Kyosho Pure Ten EP KX-One Manual

Transcription

1 Before commencing assembly, please read these instructions thoroughly! R THE FINEST RADIO CONTROL MODELS INSTRUCTION MANUAL RADIO CONTROLLED ELECTRIC POWERED TOURING CAR SERIES PureTen EP WD CHASSIS KIT KX-One INDEX Required for operation Radio preparation Before you begin Assembly Operating your model safely Spare parts & Optional parts Exploded View SAFETY PRECAUTIONS This radio control model is not a toy. First-time builders should seek the advice of experienced modellers before commencing assembly and if they do not fully understand any part of the construction. Assemble this kit only in places out of children's reach! Take care before operating this model. You are responsible for this model's assembly and safe operation! Always keep this instruction manual ready at hand for quick reference, even after completing the assembly. Ni-Cd The product you have purchased is powered by a rechargeable battery. The battery is recyclable. At the end of its useful life, under various national / state and local laws, it may be illegal to dispose of this battery into the municipal waste stream. Check with your local solid waste officials for details in your area for recycling options or proper disposal. *SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE. 00 KYOSHO No. 00

2 NI-CD BATTERY JRM No.70 NI-CD BATTERY 0AT R THE FINEST RADIO CONTROL MODELS JRM R REQUIRED FOR OPERATION () AA-size Batteries (For Transmitter) ch with electronic speed controller and servo radio control set AA AA CAUTION: Only use a surface radio with channels and electronic speed controller! (Any other radio is prohibited!) Suitable servos, receiver & electric speed controller Stick-type ch radio set Standard Size Servo Electric Speed Controller 0 9mm This kit requires a channel radio control set with electronic speed controller. Wheel-type 6 mm 0mm ch radio set Because there are stick-type and wheeltype transmitters, use which ever fits your convenience best. For more information on the radio control set, refer to its instruction manual. Receiver 0mm Approx. 0mm 50mm Approx. 50mm 7.V-000mAh XFORCE 7.V-00mAh Operation/Receiver Battery XFORCE 7.V-00mAh 000 Ni-Cd Battery and Charger for Ni-Cd Battery 7.V-000mAh XFORCE Ni-MH Battery XFORCE 000 Ni-MH Separate Type Battery is also available. X- DC X- AC A single Ni-Cd battery powers operation and receiver. Batteries listed right are suitable. X-CHARGER DC X-CHARGER AC Two types of chargers are available. One operates for 7.-8.V Ni-Cd & Ni-MH on a V car battery. The other operates on a 00V house outlet. Ni-Cd Motor Body Tire / Wheel / Inner Sponge (Pure Ten Size) 90mm /0 Use a 50 size motor. This kit does not include a body shell. Purchase one for :0 scale cars, with about 90mm in width. mm Gear ratio included in the kit suits T motor. Use tires, wheels and Inner Sponge less than mm width. 5 Paint and Brush For painting the body, use Kyosho paints for models! No.0 PAINT BRUSH POLYCA COLOR No KYOSHO SPRAY COLOR CAUTION: Before using spray colors, always read their explanations! KY OSH O S PR AY CO LO R MICRON LINE TAPE No.9670 No.97 No.8 (mm x 5m) 8 (.5mm x 5m) 8 (.5mm x 5m) 859 (0.mm x 8m) 860 (0.7mm x 8m) KYOSHO D FLEX COLOR DECAL Micron Line Tape Super-flexible tape for masking and detail designing jobs. Self-adhesive super-flexible sheets that bond to polycarbonate - even when applied to curved surfaces. MASKING SHEET For safe masking jobs, use this plastic masking sheet featuring one self-adhesive edge.

3 REQUIRED FOR OPERATION () Tools required Needle Nose Pliers Phillips Screwdriver ( L. M. S. ) CAUTION: Handle tools carefully! Instant Glue Sharp Hobby Knife Wire Cutters Awl Rubber Cement Threadlocker (screw cement) TOOLS INCLUDED Hex Wrench Grease Cross Wrench Grease No.80 No.89 SPECIAL TAPER REAMER ROUND CUTTER & SANDER No need to pre-drill! For trimming bodies! Drills neat mm to 5mm Cutting along curved lines holes directly! never was so easy! RADIO PREPARATION A new Ni-Cd battery must be charged before it is used. Refer to the charger instruction manual for charging. Set up the radio control system as indicated below. Ni-Cd Battery Charger Electronic Speed Controller 7 ON 9 OFF 5 Transmitter ON OFF Servo START FINISH Receiver 9 Switch off. (Receiver) 0 Switch off. (Transmitter) Retract the antenna. (Transmitter) Switch Install batteries. (Transmitter) Extend the antenna. (Transmitter) Connect the Ni-Cd battery. Extend the antenna. (Receiver) Center the trims. Switch on. (Transmitter) Switch on. (Receiver) 8 8 Make sure the servos are in command. 9 0

4 BEFORE YOU BEGIN () Read through the manual before you begin, so you will have an overall idea of what to do. Check all parts. If you find any defective or missing parts, contact your local dealer or our Kyosho Distributor. How to read the instruction manual: No., No.5, No.6 Front Suspension 5 x 0mm Metal Bushing This instruction manual uses several symbols. Please note them during the entire assembly. 5 King Pin mm Pillow Ball (Black) 6 R 7 L 5 8 Key Number, Part Name, True-to-scale Diagram, Quantity Used All parts except screws are identified by key numbers. For purchasing spare parts, find the key no. of the part needed in the spare part list and refer to the left column to look up the corresponding order no. Symbols used throughout the instruction manual, comprise: Part bags used. Apply instant glue (CA glue, super glue). mm Assemble left and right sides Assemble in the specified order. the same way. Drill holes with the specified diameter (here: mm). True-to-scale diagram. Apply rubber cement. Cut off shaded portion. Must be purchased separately! x Apply grease. Assemble as many times as Tentatively tighten. specified (here: twice). Apply threadlocker (screw cement). Ensure smooth non-binding movement while assembling. Pay close attention here! 90 No.90 Ball bearings are optional! (with optional part no.)

5 BEFORE YOU BEGIN () 5 This kit contains screws and hardware in different metric sizes and shapes. Before using them, check the screws on the true-to-scale diagrams on the left side in each assembly step. Some screws are extras. SCREWS Screw Self-tapping (TP) Screw OTHER HARDWARE Screw Washer Nut E-ring Cap Screw TP F/H Screw mm mm mm mm Flat Head (F/H) Screw Set Screw F/H Screw Metal Bushing Bearing 5mm Pillow Ball mm mm 0mm 5.8mm 6 Correct Self-tapping (TP) screws cut threads into the parts when being tightened. Excessive force may permanently damage parts when tightening TP screws. It is recommended to stop tightening when the part is attached or when some resistance is felt after the threaded portion enters the plastic. Wrong Overtightened. The threads are stripped. MEMO 5

6 ARRANGEMENT OF PLASTIC PARTS ON RUNNERS No No. 78 Shaded parts are not used No.7 No.8 Shaded parts are not used. Shaded parts are not used

7 Chassis No.,0 x 8mm Screw 8 For Right Side. x8mm x8mm x8mm x8mm For Left Side. Chassis No.,0 x 6mm Screw x 0mm Round Head Screw x 8mm TP TP Screw x8mm For Left Side. x0mm x6mm Part bags used. 7

8 Chassis No.,,,9,0 x 8mm Screw x mm F/H Screw 9 x 6mm Screw x 0mm TP TP Screw x mm Round Head Screw 5 7 x6mm 0 x 8mm TP TP Screw 5 6 Note the direction. x0mm 7 Aluminum Frame Spacer x8mm xmm 8 xmm x8mm(tp) x0mm No.,0 Front One Way Unit x 6mm Screw x 8mm Ball Bearing Note the direction. x6mm 8 Part bags used. Apply instant glue (CA glue, super glue).

9 No. 5 Gear Differential 5 5 Note the direction. 9.6 x 5mm Cap Screw Place the differential balls into 6 and apply ball differential grease Ball Differential Grease Remove oil deposits from 7 and 8 before applying a small amount of ball differential grease to the spots marked with 7 8 x 0 Apply grease on 0, and put on 8pcs. x 8mm Ball Bearing 0 Thrust Washer 8 Thrust Plate mm Hex Wrench /6 Thrust Ball 8 6 / Ball 7 8.6x5mm Follow illustration below, to tighten.6 5mm Cap Screw properly Now, hold the differential case firmly and rotate part 5. If part 5 rotates into the opposite direction to part 5, no further adjustment is necessary. If part does not rotate, screw 9 is Secure parts and 5 in place with two flat head screwdrivers and rotate the differential case until it becomes tight. Then, too tight. In this case, gradually loosen screw 9 until part tighten screw 9. When running the car, the differential must rotates. be tight, otherwise it may damage and MAINTENANCE As soon as the ball differential's smooth action becomes rough, parts 6, 8, 0 and may have become "gritty". If this happens, disassemble the unit and clean these parts, apply more grease and reassemble. If the action is still not smooth, the parts are worn and, therefore, must be replaced. We recommend that these parts be replaced from time to time to ensure smooth running. Part bags used. Apply grease. Apply instant glue (CA glue, super glue). Assemble as many times as specified. x 9

10 6 Chassis 7 0 x 5mm Ball Bearing 8 No.,,0 Bearing Color (Rear) Note the direction Note the direction. 7 8 Wipe out oil. Rolling it, insert x 0mm Ball Bearing Place Drive Belt properly as illustration shown. 9 Bearing Color (Front) x 0mm Round Head Screw 0 A Front Cup Joint A x 0mm TP TP Screw Install as illustration shown. Note the direction. Note the direction. x 6mm Screw x 8mm TP TP Screw x0mm(tp) x mm Round Head Screw x0mm x6mm x8mm x6mm x8mm x0mm(tp) xmm 0 Part bags used. Pay close attention here!

11 7 Chassis No.,,,0 7 0 x 5mm 8.6x8mm Ball Bearing Bearing Color (Rear) x 8mm TP TP Screw x8mm x8mm.6 x 8mm TP TP Screw B Front Cup Joint B Wipe out oil. Rolling it, insert Chassis x mm Set Screw No.,0 mm Place Set Screw as shown. Do not tighten too much. xmm xmm Adjust to place the pulley center as shown. Make sure the pulley rotates smoothly. xmm Part bags used. Pay close attention here!

12 No.,0 9 Motor Plate mm x 5mm F/H Screw x 8mm F/H Screw 6 5 mm Nut x5mm 6 7mm Aluminum collar 6 6 x8mm 0 No.,0 Center Pulley Cut the excess plastic xmm Place the pulley under the belt. Apply threadlock and place on flat part. 0 mm x 8mm Ball Bearing mm Nylon Nut x mm Set Screw xmm Adjust the space by the xmm set screw, so they don't touch each other. Part bags used. Pay close attention here! Apply instant glue (CA glue, super glue). Apply threadlocker (screw cement).

13 Tensioner No.,0 x 8mm Cap Screw 6 mm Washer 6 5 x 0mm Ball Bearing 6 5 Install the belt as illustration shown. Tension Collar x 8mm mm mm x 8mm Adjust Belt Tension Press by the finger and tighten the screw. Do not tighten too much. x 6mm Screw Loosen slightly. ( same as opposite side) 6 Install 6 Spur Gear. T 8T Generally loosen the belt tension when using big torque type motor such as T. While tighten the belt tension when using high revolution type such as 8T. If tighten the belt tension too much, it may cause bad response and skip the belt teeth. 6 x6mm Part bags used. Tentatively tighten. Apply instant glue (CA glue, super glue).

14 Shock Stay No.,0 x 0mm < For Front > Cap Screw 7 mm Nut x0mm mm Nylon Nut 9 8 x 8mm mm TP TP Screw x8mm mm Nylon Nut x 8mm Screw < For Rear > x 0mm Screw 9 5.8mm Pillow Ball 50 x8mm(tp) x0mm 8 mm Tapered Washer mm Ball Nut mm x8mm x0 mm No.5,0 Front Suspension.6 x 6mm Round Head Screw < For Right Side > 8 Cut little by little not to crack the part. 8 < For Left Side> 5 5 Short Long Short Long.6x6mm < For Right Side > < For Left Side > Part bags used. Pay close attention here! Assemble left and right sides the same way. Cut off shaded portion.

15 No.5,0 Front Suspension < 9 5.8mm For Right Side> Pillow Ball mm 8 mm 8 Tapered Washer 9 mm Nylon Nut x 0mm Ball Bearing Apply threadlock. Flame a moment when disassemble the parts. x 5.5 x 9mm Pin < Right > L King Pin (L) 6 Not to tighten too much. 60 LL 58 King Pin (LL) 58 x 8 x mm Plastic Collar < Left > Note the direction. mm Not to tighten too much. mm 6 No.,5,0 5 Front Suspension E.5 E E-ring 6 Suspension Shaft < Right > 9 8 < Left > 9 5.8mm Pillow Ball 65.8mm (S) Ball Stud (S) E.5 8 mm Tapered Washer Part bags used. Apply grease. Assemble left and right sides the same way. Ensure smooth non-binding movement while assembling. Assemble in the specified order. Assemble as many times as specified. x 5

16 No.5,0 6 Front Suspension 67 x 57mm Shaft 66 Sponge E.5 E.5 E E-ring E.5 No.5 7 Front Suspension mm L Ball End (L) 69 x 0mm Adjustable Rod The side with the step is a reverse screw. mm approx. mm x 6 Part bags used. True-to-scale diagram. x Assemble left and right sides the same way. Assemble as many times as specified.

17 No.,5,0 8 Front Suspension xmm x mm Set Screw 7 Stabilizer Ball xmm 7 7 x 0mm Screw Insert 7 as shown. x0mm xmm 7 Tighten the set screws and make sure part 7 is stable. No.6 9 Rear Suspension mm Pillow Ball 8 8 mm 75 Tapered Washer Parts assembled step 6 5 x 0mm Ball Bearing 6 x Part bags used. Pay close attention here! Ensure smooth non-binding movement while assembling. Assemble as many times as specified. Assemble left and right sides the same way. Assemble in the specified order. x 7

18 0 E.5 No.,6,0 Rear Suspension E E-ring 6 Suspension Shaft mm Note part (S) 75 has each right and Ball Stad (S) left different shape. Lean the tires toward the right way as illustration shown E.5 Cut off shaded portion if part 75 and 76 contacts. < Left > 6 < Right > Use this hole No.6,0, Rear Suspension 67 x 57mm Shaft E.5 E E-ring 78 x 6 x mm Plastic Collar E E.5 No.6 Rear Suspension mm The side with the step approx. 6mm is a reverse screw. x mm L 79 x mm Ball End (L) Adjustable Rod 8 Part bags used. Pay close attention here! Assemble left and right sides the same way. Assemble as many times as specified. True-to-scale diagram. x

19 No.6,0 Rear Suspension 0.8mm (M) Ball End (M) x 0mm 0 Set Screw x 6mm Screw x 0mm x xmm 7 5 x mm Set Screw 7 Stabilizer Ball 6mm approx. 6mm 5 x6mm No.,6,7 Oil Shock 8 O O-ring (White) 80 8 Shaft Slider (White) mm (S) Ball End (S) 8 8 Apply Silicon Oil. For Front : pcs For Rear : pc 0mm : For Front mm : For Rear x 5 x mm Plastic Collar 8 85 x x For Front Grab with a piece of cloth. For Rear No.7 5 Oil Shock Stop-ring 87 O O-ring (Black) Silicon Oil (For shock absorber) 88 Thrust in the Pressure Top 90 as shown with care not to tear 89 it up and have it stick fast. Wipe out oil flown over with facial tissue or the like Pressure Top x Move down the piston and put some oil. Move up and down the piston slowly to get rid of air bubbles. Part bags used. Pay close attention here! True-to-scale diagram. Assemble as many times as specified. Assemble in the specified order. Ensure smooth non-binding movement while assembling. Assemble left and right sides the same way. x 9

20 No.7 6 Oil Shock There are types of 9. You can adjust the car clearance to be level fore and aft while running by picking up correct types mm Ball 5 mm Shock Stopper 5 Compress the spring for This is for adjusting the spring. inserting x No.7 7 Oil Shock 95 Shock Aluminum Collar 96 mm Plastic Nut Note the direction < Front > Note the direction < Rear > 0 Part bags used. x Assemble left and right sides the same way. Assemble as many times as specified.

21 8 Radio.6 x 6mm F/H Screw 0 5.8mm Servo Ball.6 x 6mm Round Head Screw.6 x 6mm TP TP Screw x 6mm Round Head Screw x 6mm TP Round Head TP Screw No.8, Insert 0 through 00 ( 0 or 0 ) to install 99 spring. After installing 99 spring, pull 0 away Choose this part, depending on the servo. HITEC FUTABA KO JR SANWA Use the screws included the servos..6x6mm Use following screws for alternative..6 x 6mm Screw.6 x 6mm TP Screw x 6mm Screw x 6mm TP Screw Place the servo under 0 neutral condition. { No. No.5 No. 9 Radio No.,8,0 Short x0mm mm L Ball End (L) Long 05 x 0mm Adjustable Rod x 0mm Screw (silver) mm mm Washer Nut mm mm mm The side with the step approx. 7mm is a reverse screw. x Part bags used. Must be purchased separately! x Assemble left and right sides the same way. Tentatively tighten. Assemble as many times as specified. True-to-scale diagram.

22 0 Radio No.0 x 5mm Screw mm Washer mm x5mm Servo Backward Front Pulley Place Servo Horn center of the chassis. Place the servo backward not to contact Front Pulley. No.,8,0 Radio x 0mm Screw x mm Screw mm Washer 5 07 If there is a space here, insert mm washer between x0mm mm mm Nut xmm mm mm xmm Part bags used. Tentatively tighten. Assemble left and right sides the same way.

23 Motor No.8,0 x 8mm Screw mm Washer x mm Set Screw mm Motor x8mm.5mm Hex Wrench Insert a sheet of paper between both gears and xmm tighten both screws that hold the motor. 08 Firimiy tighten the set screw on to flat spots. Radio Plate No.9,0 x mm TP TP Screw 8 x 0mm Set Screw x0mm Cut off shaded portion. 0 x0mm 0 09 Tighten with.5mm Hook Pin. Do not tighten too much. xmm 5mm 09 xmm Cut off shaded portion. Part bags used. Must be purchased separately! Cut off shaded portion. Assemble left and right sides the same way.

24 Radio Plate No.,9,0 x8mm Hook Pin x 8mm F/H Screw 5 Radio Hook Pin No.9,0 Speed Controller Place Receiver and Speed Controller parallel with chassis. Receiver Antenna 6 5 Double-sided Tape Switch Take care of wiring. Part is removal for changing a battery. AMB In case of using AMB Transmitter. ( Transponder) 5 Double-sided Tape Connect as per radio equipment instruction manual. Strap down the cords as they may trail on the ground or into moving parts. 7 Part bags used. Assemble left and right sides the same way. Must be purchased separately!

25 6 Tire Mould Inner mm Use tires for /0 Touring Car. ( less than mm width) In case wheels contact Rear Sus Arm, cut off the part of Rear Sus Arm. x After fitting them together, pour instant Insert the wheels inside the tires as shown. Twist the tire onto the wheel. glue along the seam. No.,,9,0 7 Tire and Front Bumper x8mm 8 x mm Pin x 8mm TP TP Screw < Front > 9 mm Flanged Nylon Nut 0 x Assemble all four tires the same way. Take care not to tighten too much. 6 8 x8mm mm x Part bags used. Assemble as many times as specified. Pay close attention here! Apply instant glue (CA glue, super glue). Ensure smooth non-binding movement while assembling. 5

26 No.8,0 8 Body Mounts x 6mm TP TP Screw Adjust height of body mount depending upon kind of body. Cut off excess part. < Front > x6mm No.8,0 9 Body Mounts x 6mm TP TP Screw Adjust height of body mount depending upon kind of body. Cut excess comes down. x 8mm Screw mm Nut mm < Rear > Note the direction. Top x6mm x8mm Apply threadlock. 0 Battery No.9 Attach after battery is loaded. Disconnect Ni-Cd battery when it is not in use. < > < Straight Packed Battery > Ni-Cd Battery < > < Separated Battery > 6 Apply Sponge Tape if there is a space between Battery Sponge Tape and Radio Plate. Part bags used. Cut off shaded portion. Pay close attention here! Assemble left and right sides the same way. Must be purchased separately!

27 Body Shell No.0 Hook Pin No.9965 When using Altezza body, drill holes to match the chassis. Combine Spur & Pinion according to the motor. Gear Ratio T T T 8.0 Included in this kit. Pinion 0T T T T T 5T 6T 7T 8T 9T 0T T T T T 5T 6T 7T 8T 9T 50T Spur 05T 0T 5T 0T 5T Shock Adjustment No.,7 5 xx0.mm Rebound Adjustment Piston Function Speed Adjustment Shim x5 x mm Plastic Collar x5xmm A 6 Piston A T Motor : 0 5 x x 0.mm B : 0 pc Shim Using Plastic Collar makes the length of Piston B E. E8T T Shock short. E-ring Motor Also adjust the length, screwing Shock : End. : pcs Adjust Front Shock little longer than Rear Shock. Generally use a shorter shock on slippery surface. On the other hand, use a longer shock on high traction surface. Lifting up the car and down, balance both right and left tires on the ground at the same time. Using mobile Piston A, it makes difference speed of extending and shrinking. Under the original condition, extending speed is faster than shrinking speed. When the difference of extending and shrinking speed is big, it would be easier to turn mildly. While the difference is small, it gives quick response of steering. Part bags used. Must be purchased separately! Pay close attention here! 7

28 Location of Knuckle Arm can be adjusted. Front Hub 59 Set 9 x8xmm 6 9 x8xmm Plastic Collar is placed under Knuckle Arm. Set 58 x8xmm Standard 58 x8xmm Plastic Collar to both below and above the Knuckle Arm. 58 Set 9 x8xmm 9 x8xmm Plastic Collar is placed over the Knuckle Arm Set Set Set for high grip track. Set for low grip track, but this is up to your preference. If the location of Plastic Collar is changed, Chassis Height and Rebound should be adjusted, too. Adjust by changing the length of Steering Rod. Front Toe Angle Steering Characteristics Toe - in Straightline stability becomes better. Mild steering. Toe - out Quick steering. To change Camber Angle, adjust the length of Upper Rod. Camber Angle Making longer. Positive Camber Shortening. Negative Camber Front / Rear Steering Characteristics Front Steering becomes milder. Rear Rear tire grip becomes worse when entering corners. Front Enters corners more aggressively. Rear Gives rear tires more grip when entering corners. MEMO 8 Ensure smooth non-binding movement while assembling.

29 OPERATING YOUR MODEL SAFELY WARNING: Do NOT operate the model in the following places and situations: (Non-observance may lead to accidents!) Always check the dry batteries in the radio! When the dry batteries get weaker, transmission and reception of the radio decrease. You may lose control of your model when operating it under such condition. This may lead to accidents! Operate the model in spacious areas with no people around! Do NOT operate it:. on roads!. in places where children and many people gather!. in residential districts and parks!. indoors and in limited space! * Non-observance may account for personal injury and property damage! Keep in mind that people around you may also operate a radio control model! NEVER share the same frequency with somebody else at the same time! Signals will be mixed and you will lose control of your model. This may lead to accidents! When the model is behaving strangely...! Immediately stop the model and check the reason. As long as the problem is not cleared, do NOT operate it! This may lead to further trouble and unforeseen accidents! WARNING: in order to avoid accidents and personal injury, be sure to observe the following: Do NOT put fingers or any objects inside rotating and moving parts! Rotating / moving at high speed, you may be seriously injured! After operation, the electric motor and Ni-Cd battery are hot! You may burn yourself seriously touching them! Before charging, please carefully read the explanations of the Ni-Cd battery and charger unit! While charging, the Ni-Cd battery and charger unit get hot! NEVER charge on top of or near easily inflammable material as this will result in fires! NEVER short out Ni-Cd batteries!. Do NOT disassemble or modify Ni-Cd batteries!. Ensure the cords do NOT trail into rotating and moving parts! Ni-Cd batteries use heavy metals that are noxious to health! NEVER throw them into fires as they will explode! ALWAYS return disused Ni-Cd batteries to the shop! Do NOT dispose of them into the usual waste stream! 9

30 PRE-RUN CHECKLIST Are all screws securely tight? Are the radio batteries fully charged? Are the onboard batteries fully charged? Is the backlash properly adjusted? Does the car's steering react according to your transmitter inputs? Does the speed (electric speed controller) change according to your transmitter inputs? Is the Ni-Cd battery securely attached? Is the running area safe? Is nobody using the same frequency as you do in the same running area at the same time? A the wheels and tires securely attached? Are all rotating parts greased? Do moving parts not contact anywhere? Do the shocks move and damp? EVERYDAY MAINTENANCE Make sure screws and nuts are securely tightened and parts are not worn. Grease all rotating parts. Repair wiring if for example cords drag on the ground or cords are damaged. Should the servo cords and the antenna be damaged, get them repaired by their manufacturers. Make sure the suspension train ist broken due to crashes. Make sure that gears are not worn or damaged. Remove dirt from the chassis. 0

31 BATT. BATT. BATT. BATT. BATT. BATT. BATT. / PROPER OPERATING PROCEDURES Fully charge the Ni-Cd battery. Check the transmitter batteries. Make sure the throttle control is in neutral. CH- CH- CH- CH- 5 Connect the Ni-Cd batter Extend the transmitter antenna. Switch on the transmitter. 6 ON CH- CH- CH- CH- OFF ON Switch on the receiver. Make sure the model steers according Make sure the speed (electric speed controller) to your transmitter inputs. changes according to your transmitter inputs. ON CH- CH- CH- CH- 0 Make sure the running area is safe. / AFTER FINISHING RUNNING After finishing running, collect your car. Switch off the receiver. Switch off the transmitter. Do not leave on the racing car. OFF STOP OFF CH- CH- OFF ON 5 Remove dirt from the chassis. OFF Disconnect the Ni-Cd battery. CHECK When NOT using the model, always switch off the receiver and transmitter! Furthermore, disconnect the Ni-Cd battery and remove it from the model! This may lead to overheat and fires!

32 TROUBLESHOOTING Steering control servo does not operate. Transmitter and/or receiver is not switched on. Transmitter batteries are weak. Improper radio installation. Switch on. Replace with new batteries. Correct as per radio instruction manual. Motor does not run. Ni-Cd battery capacity is insufficient. Improper radio installation. Loose connectors. Motor trouble. Recharge Ni-Cd battery. Correct as per instruction manual. Make connectors tighter with minus screwdriver. Replace with a new motor. Motor runs but car does not run. Pinion gear is not installed. Or, screw is loose. Tighten screw that holds pinion gear. Not enough speed. Wheels hardly rotate/do not rotate at all. Ni-Cd battery capacity is insufficient. Electronic speed controller is not properly adjusted. Dirt entered rotating parts on wheels. Backlash is too tight. Recharge Ni-Cd battery. Adjust throttle trim (transmitter). Should electronic speed controller not shift into high, readjust it as per instruction manual. Clean and regrease. Readjust as per instruction manual. Even when releasing throttle, car does not run. Electronic speed controller is not properly adjusted. Adjust throttle trim (transmitter). Should electronic speed controller not shift into high, readjust it as per instruction manual.

33 SPARE PARTS FOR JAPANESE MARKET ONLY. No. No. No. Part Names Quantity No. Part Names Quantity KX00 0 x LL Spur Gear Shaft SP King Pin (LL) 60 x KX00 8 x 7 (0T) x Drive Pulley Set (0T) 500 SPW5 Adjust Rod Set 69 x 650 KX00 Tensioner Set 5 x 600 SPW5BK (M) Urethane Bumper (M) Black 0 x 500 KX00 7 x 6 x 07 x Frame Collars 600 SPW0 -V 6 Front Hub 6 x 9 x 58 x 600 KX005 5 x Motor Mount 00.8mm UM.8mm Ball End 85 0 x 6 00 KX006 TypeA 7 x Front Shock Stay TypeA 00 UM9 Diff. Ring 8 x 500 KX007 TypeA Rear Shock Stay TypeA 50 x 500 / UM0 / Ball 6 x 00 KX008 7 x Diff. Housing 700 UM 9 Diff. Adjust Screw x 50 KX009 5 x Diff. Cup Joint 000 UM9.8mm (S).8mm Ball Stad (S) 65 x 00 KX00 (9T) Pulley Set (9T) 5 x x 800 WBD7 Diff. Adjust Spring x 50 KX0 Front Suspension Plate 68 x 00 W0 mm 8 x 0 mm Tapered Washer 50 KX0 67 x x Suspension Shaft 700 W56- Shock Case (Plastic Parts) 9 x KX x W60 T Universal Swing shaft 600 Pinion Gear (T) 08 x KX0-0T 56 x 600 W60 6 x Wheel Shaft Spur Gear (0T) KX0-5.8mm Drive Shaft 57 x mm Pillow Ball 9 x KX0-700 S 5 55 x x 8 Joint Pin Set KP/KY Fluorescent Nylon Strap (S) Pink / Yellow 80 KX0 Front One way Unit x Color Antenna (Black Cap) 6 x 500 KX05 One Way Cup Joint 0 x x Shock Case 000 KX05- Sponge ( for Cup Joint ) 66 x x Shock Cap 600 KX06 5.8mm (S) 5.8mm Ball Nut (S) 0 x Lower Cap Set 8 8 x 600 KX07 Shock Absorbing Tape x Stop-ring Set x 700 KX09.8mm mm.8mm 7 x x 0 mm O-ring (White) 500 KX0 Knuckle Plate 8 x mm mm Ball Set 95 x 00 KX0 Assy Drive Belt x Variable Piston Assy. 8 x 700 KX0 Main Chassis x 000 xx0.mm xx0.mm Shim Set 5 x E. x 8 00 KX xmm Direct Servo Saver x xmm Pin 8 x 8 00 KX05 0 x 09 0 x Battery Holder Set Snap Pin x 0 00 KX Plastic Parts Set x 6 x 96 Suspension Shaft 6 x E.5 x 50 KX07 KX08 Frame Set 5 x mm 5.8mm Ball Nut 5 x x Bumper Set x x 8 97 Body Mount x x KX09 (KX-One) x Decal (KX-One) Double-sided Tape 5 x 00 LA (L) 0 x 5mm King Pin (L) 59 x x 5mm Ball Bearing 7 x 00 LA 5.8mm 70 x 5.8mm Ball End Diff. Thrust Bearing 0 x x 8 00 OT6VB 5 x 0mm Knuckle Arm 5 5 x x 5 x 0mm Ball Bearing 000 OT 5.8mm x 8mm 9 x mm Ball x 8mm Ball Bearing x 000 OTW S 79 x Adjust Rod (S) 00 OTW M Adjust Rod (M) 05 x 00 SP0 Drive Hub, Pulley Set x 00 Some of the parts included are not available as spare parts. Purchase optional parts instead. SP0B Suspension Arm Set x 600 SP07V- Rear Hub x 00

34 OPTIONAL PARTS FOR JAPANESE MARKET ONLY. No. No. No. Part Names Quantity No. Part Names Quantity KXW0 90 Titanium Screw Set Light Weight / BK Aero Wheel (5-spoke / black) KXW0...6, / Front Stabilizer Set Diameter:.,.6,.8mm 600 Aero Wheel (5-spoke / white) 800-8W KXW0.,.,.6,.8,.0 7 x Rear Stabilizer Set 90-5 VM-5MN Diameter:.,.,.6,.8,.0mm 900 V Slick Tire M-5MN 000 (mm JMRCA 90-0 VM-0MN 5 5 = V Slick Tire M-0MN Includes pcs. Medium 000 KXW0 Rear Belt Tensioner Prevent from skipping the belt at 00 Narrow Size (mm width) the time of breaking and reverse VM-5MN V Slick Tire M-5MN 5 5 = Soft Hard KXW05 Multi Ride Height Gauge For measurement Multi Ride Height 800 Racing Battery Holder Made from Carbon. Light weight. 99 On-road Spring Set Includes kinds (each) (S) KXW06 On-road Spring Set (S) Includes kinds (each) 800 Oneway Universal SwingShaft Gives quick response of steering with One Way Bearing on Drive Shaft. 967 Super Narrow Wheel 00 (mm JMRCA RC M Racing Slick Tire M-5 00 SPW0V 7 7 Front Hub 7 Hub Carrier ( 7 camber) M-0 Includes pcs. Super -0 Racing Slick Tire M-0 Narrow Size 00 SPW M = Soft Hard Front Hub 0 Hub Carrier (0 ) 600-0V -0 Racing Slick Tire M-0 00 SPW6 SP 990 SP Gear Holder Aluminum Gear Holder 500-8S Aerodish Wheel 8pcs 800 SPW (H) Hard Rear Hub Aluminum Rear Hub (0 ) 00-8H Aerodish Wheel (H) 8pcs 800 SPW Hard Rear Hub Aluminum Rear Hub ( ) 00 -BK Aerodish Wheel (Black) pcs W509 M-5MN Damper Oil Decal 5 difference color. For sign of oil container Racing Slick Tire M-5MN mm ( JMRCA 00 W600 0T) /6 ( 990 M-0MN 600 Pinion Gear (0T) -0 Racing Slick Tire M-0MN 00 Includes pcs. Medium 990 M-5MN Narrow Size Matches with /6 Inch Racing Slick Tire M-5MN 00-5 W T) 5 0 = Soft Hard Pinion Gear (50T) Pitch ( Pinion Gear Motor M-0MN -0 Racing Slick Tire M-0MN 00 W605 05T 990 Spur Gear (05T) 50 MN-0-0 Mould Inner Form MN-0 (mm 00 0T 990 W60 MN-0 Spur Gear (0T) 50-0 Mould Inner Form MN-0 Includes pcs. Medium 00 /6 5T /6 Inch Pitch Spur Gear 990 Narrow Size W65 MN-0 Spur Gear (5T) 50-0 Mould Inner Form MN = Soft Hard 00 W65 5T (S) Spur Gear (5T) Dual Springs (S) Special Antenna Holder Aluminum Antenna Holder 500 (M) 99 Dual Springs (M) Hobby Shears & Sander 000 (H) 99 Dual Springs (H) Use with 99. A set 00 Includes different type mm Body (ALTEZZA) 99 Matches with 90mm chassis. 000 Ring Set of springs.( each) 600 Makes various spring Precision Camber Gauge For best alignment 997 Dual Springs (S) hardness Assy - Piston Shaft Assy steps adjustment available 90 Loctite (medium strength) Fixes screws (0T) T Xspeed Modified Motor 800 Ball Diff. Grease Stops vain slip of Ball Differential 800 Gives big power in HG 800 HG Joint Grease Decreases a friction (7T) severe competition T Xspeed Modified Motor One Way Bearing Grease Prevents from slipping of One Way Bearing T -SS Xspeed Stock Motor SS x7mm 5x7mm Shim Set To make up for extra space of wheel parts X-FORCE 000 X-FORCE Straight NI-MH Battery 6800 Straight NI-CD Battery x6mm x6mm Shim Set To make up for extra space of wheel parts X DC DC X CHARGER DC DC Battery Charger for NI-MH 9800 X AC C Taper Reamer Handy to drill a hole for body mount Maintenance Stand Convenient stand for work Team KYOSHO Team KYOSHO Transmitter Bag Transmitter Carrying Bag 800 (H) On-road Spring Set (H) Includes kinds. (each) 800

35 OPTIONAL PARTS FOR JAPANESE MARKET ONLY. No. No. No. No. Part Names Qty. No. Part Names Qty. No. Part Names Qty Silicone Oil (00) Silicone Oil (00) Silicone Oil (000) Silicone Oil (50) Silicone Oil (500) 9675 Silicone Oil (000) for shocks Silicone Oil (00) Silicone Oil (600) Silicone Oil (5000) 600 for diffs for shocks Silicone Oil (50) 9660 Silicone Oil (800) Silicone Oil (6000) Silicone Oil (00) 965 Silicone Oil (000) Silicone Oil (7000) for diffs Silicone Oil (50) 9675 Silicone Oil (000) FOR JAPANESE MARKET ONLY. mm mm No. Size (mm) QUANTITY No. Size (mm) QUANTITY No. QUANTITY 00 Round Head Screw Round Head Self-Tapping Screw Nut x6 x8 x0 x5 5 each x x6 x8 x0 5 each 7 mm.6mm 0 each.6x8.6x0.6x.6x 5 each.6x6.6x8.6x0.6x5 each 7 mm mm 0 each x x6 x8 x0 x 5 each x6 x8 x0 x x 5 each x x6 x8 x0 5 each 5 x5 x6 x8 x0 5 each 00 Flanged Nut x6 x8 x0 x 5 each 6 x5 x0 x5 5 each 7 mm 0 pcs x x x6 x8 5 each 7.6x.6x5.6x6.6x8 5 each 75 mm 0 pcs Bind Screw Bind Self-Tapping Screw 00 Nylon Nut.6x.6x6.6x8.6x5 each x x6 x8 x0 x 5 each 0.6x6.6x8.6x0.6x5 each x6 x8 x0 x x 5 each mm mm 5 pcs 5 pcs x5 x6 x8 x0 5 each 79 mm 5 pcs x0 x5 x8 5 each x x6 x8 x0 x6 x8 x0 x x x5 x8 x0 x5 x8 x0 x Flat Head Screw 5 each 5 each 5 each 5 each 00.6x8.6x0.6x.6x 5 each x6 x8 x0 x 5 each x x6 x8 x0 5 each x8 x0 x5 x0 5 each x x x6 x8 5 each x0 x x x5 5 each 00 Cap Screw x8 x0 x x each.6x8.6x0.6x.6x each x8 x0 x x each x5 x6 x8 x0 each x5 x0 x5 x0 each x0 x5 x0 each x5 x8 x0 each x5 x0 x5 each SCREW NUT etc Flat Head Self-Tapping Screw x6.6x8.6x0.6x5 each x6 x8 x0 x x 5 each x5 x6 x8 x0 5 each 85 x5 x0 x5 5 each Flanged Cap Screw x6 x8 x0 x8 x0 x Screw x8 x0 Set Screw x6 x x x6 x x x5 x0 x x5 x8 x 5x 5x5 5x6 5x0 5x0 each each 00 0 each 00 each each each each each 65 x0 x5 each mm E.5 E.0 E.5 E.0 E.0 E5.0 E6.0 E7.0 E0.0 Flanged Nylon Nut Washer mm.6mm mm mm 5mm E E-Clips 5 pcs 0 each 0 each 50 0 pcs 0 pcs 0 pcs 0 pcs 0 pcs 0 pcs 0 pcs 6 pcs 6 pcs 5

36 00 KX-One 00 KYOSHO EXPLODED VIEW < > Parts indentified only by key numbers are not sold individually 6 7 A F F B A G E C D D E C G 96 5 KX05 KX06 6 KX KX0- KX0 KX0- KX0- KX0 - OT6VB 5 SP W0 8 LA 59 LA 70 LA 70 OTW 79 LA W0 8 LA 70 KX0 67 KX0 67 UM9 65 UM OTW 05 KX06 KX0 0 KX05 09 KX05 0 SPW0-V 6 SPW0-V 58 KX07 KX05 8 W KX08 7 KXW KX08 W56 - W UM 80 W56- W OT LA 70 SPW5 69 LA 70 KX KX SP0B 6 KX0 67 KX006 7 KX05-66 KX05 KX0 KX06 W KX06 9 KX00 KX00 KX0 KX07 KX07 SPW5BK 0 KX08 9 KX KY KX08 W60 08 KX005 5 W60 6 SP0 KX00 0 KX00 6 KX05 KX KX KX KX08 7 KX KX07 KX06 8 OT6VB 5 SPW0-V 6 KX06 SP0B 6 UM9 65 B KX0 KX KX KX06 KX06 8 KX009 KX008 7 UM KX KX007 KX009 5 WBD7 UM KX KXW0 95 W56- OT 9 7 UM9 8 UM KX00 5 KX UM 9 7 KX06 9 KX06 KX06 06 SP0B KX KX KX06 9 KX00 7 KX05 0 SP07V SP07V- 76 KX KXW UM 0 KX W KX UM W W /

37 R THE FINEST RADIO CONTROL MODELS -00 TEL. ( PRINTED IN JAPAN