Kyosho GP TR-15 Rally Manual

Transcription

1 Before commencing assembly, please read these instructions thoroughly. R THE FINEST RADIO CONTROL MODELS INSTRUCTION MANUAL GP TR-5 RALLY WD MITSUBISHI LANCER EVOLUTION VII WRC INDEX This kit is half assembled Please start assembling from page 8 ~0 8. REQUIRED FOR OPERATION RADIO PREPARATION BEFORE YOU BEGIN ASSEMBLY OPERATING YOUR MODEL SAFELY 5 6 SPARE PARTS & OPTIONAL 5 PARTS EXPLODED VIEW 8 9 SAFETY PRECAUTIONS This radio control model is not a toy! commencing assembly and if they do not fully understand any part of the construction. Assemble this kit only in places out of children s reach! completing the assembly. First-time builders should seek the advice of experienced modellers before Take enough safety precautions prior to operating this model. You are responsible for this model s assembly and safe operation! Always keep this instruction manual ready at hand for quick reference, even after *SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE. 00 KYOSHO No. 06

2 R REQUIRED FOR OPERATION () Minimum channel radio with servos, and battery box. Battery Box If already included with the CAUTION: Only use a surface radio with channels and servos! radio, no battery box needs to be pur-chased separately. Stick-type ch radio. AA-size Batteries Because there are stick-type and wheeltype transmitters, use which ever fits your convenience best. Use a transmitter with reverse function. For more information on the radio, refer to its instruction manual. Wheel-type ch radio. AA Servo AA AA Suitable servos & receiver Receiver Required for engine starting: Glow Fuel & Fuel Pump Booster Cord Plug Wrench Engines for R/C models require glow fuel. Be careful not to purchase gasoline or kerosene by mistake; both cannot be used! Also, be very careful when han-- dling glow fuel which is hi-ghly inflamma-- ble and high-explosive! Besides glow fuel, engines also require engine starting equipment. This comprises a glow plug heater (booster cord & batteries) and a plug wrench for removing and installing the glow plug. HANDY FUEL WARNING: Gasoline or kerosene cannot No.0 be used. Paint and Brush PAINT BRUSH For painting the body, use Kyosho paints for models! No.0 POLYCA COLOR No.60 6 KYOSHO SPRAY COLOR CAUTION: Before using spray colors, always read their explanations! FUELPROFF PAINT KY OSH O S PR AY CO LO R No.8 (mm x 5m) 8 (.5mm x 5m) 8 (.5mm x 5m) 859 (0.mm x 8m) 860 (0.mm x 8m) Micron Line Tape KYOSHO No No.9 D- D FLEX COLOR DECAL MASKING SHEET MICRON LINE TAPE Self-adhesive super-flexible sheets that Super-flexible tape for masking and detail designing bond to polycarbonate even when For safe masking jobs, use this plastic masking jobs. applied to curved surfaces. sheet featuring one self-adhesive edge.

3 REQUIRED FOR OPERATION () Tools required Phillips Screwdriver (L.M.S) CAUTION: Handle tools carefully! TOOLS INCLUDED Hex Wrench.5mm mm Cross Wrench Grease GREASE Needle Nose Pliers Awl Instant Glue Instant Glue RUBBER Rubber Cement Wire Cutters Sharp Hobby Knife Screw Cement SCREW CEMENT No.90 LOCTITE Medium Strength No.89 No.80 ROUND CUTTER & SANDER SPECIAL TAPER REAMER To prevent the screws For trimming bodies. Cutting along curved No need to pre-drill! from becoming loose. lines never was so easy! Drills neat mm to 5mm holes directly! RADIO PREPARATION Set up the radio control system as indicated below. Switch the reverse switch for both the steering and the throttle. ON OFF Transmitter Insert AA-size dry batteries. (Transmitter) Extend the antenna. (Transmitter) Insert AA-size dry batteries. (Battery Box) Connect the battery box. 5 Extend the antenna. (Receiver) 6 Center the trims. Switch on the transmitter. 8 Switch on the receiver. 9 Make sure the servos move according to your transmitter inputs. Servo START FINISH Switch off the receiver. Retract the antenna. (Transmitter) 0 8 ON 0 OFF Switch Receiver Switch off the transmitter. Battery Box 5

4 BEFORE YOU BEGIN () Read through the manual before you begin, so you will have an overall idea of what to do. Check all parts. If you find any defective or missing parts, contact your local dealer or our Kyosho Distributor. How to read the instruction manual: No., No.5, No.6 Front Suspension 5 x 0mm Metal Bushing This instruction manual uses several symbols. Please note them during the entire assembly. 5 5 King Pin 6 5.8mm Pillow Ball (Black) 6 R L 5 8 Key Number, Part Name, True-to-scale Diagram, Quantity Used All parts except screws are identified by key numbers. For purchasing spare parts, find the key no. of the part needed in the spare part list and refer to the left column to look up the corresponding order no. Symbols used throughout the instruction manual, comprise: Part bags used. mm Drill holes with the specified diameter (here: mm). Must be purchased separately! Apply epoxy glue. Cut off excess. Pay close attention here! Apply instant glue (CA glue, super glue). Cut off shaded portion. Apply rubber cement. Tentatively tighten. Apply grease. Ensure smooth non-binding movement while assembling. x Apply threadlocker (screw cement). True-to-scale diagram. Assemble as many times as Assemble in the specified specified (here: twice). order. Assemble left and right sides No.90 the same way. Ball bearings are optional! 90 (with optional part no.)

5 BEFORE YOU BEGIN () 5 This kit contains screws and hardware in different metric sizes and shapes. Before using them, check the screws on the true-to-scale diagrams on the left side in each assembly step. Some screws are extras. SCREWS OTHER HARDWARE Screw Self-tapping (TP) Screw Screw Washer Nut E-ring Cap Screw TP F/H Screw mm mm mm mm Flat Head (F/H) Screw Set Screw F/H Screw Metal Bushing Bearing 5mm Pillow Ball mm mm 0mm 6.8mm 6 Correct Self-tapping (TP) screws cut threads into the parts when being tightened. Excessive force may Wrong permanently damage parts when tightening TP screws. It is recommended to stop tightening when the part is attached or when some resistance is felt after the threaded portion enters the plastic. Overtightened. The threads are stripped. Included engine has no screws to adjust Air/Fuel Mixture at slow engine speed. MEMO 5

6 ARRANGEMENT OF PLASTIC / PARTS ON RUNNERS No. Shaded Parts are not used No. A B C Shaded Parts are not used. 5 6 No.5 Part bags used. 6

7 ARRANGEMENT OF PLASTIC / PARTS ON RUNNERS No.5 G-6 G- G- Shaded Parts are not used. G- G- G-6 G-5 G-5 G-8 G-8 G- G- No. Shaded Parts are not used Part bags used.

8 Differential Gear 0 05 x8mm 0 0 x 8mm TP 8 0 x 0mm Shaft x8mm x Gearbox 5 x 0mm x mm Metal Bushing Set Screw 6 x 0mm TP 0 8 x 0mm Metal Collar 5mm Washer 09 0 x mm Firmly tighten the set screws onto Metal Bushing the flat spots. xmm 0 E E E-ring xmm 5mm mm Differential Gear xmm x0mm x0mm Firmly tighten the set screws onto the flat spots. 08 x 8 x Assemble as many times as specified. Apply grease. Apply threadlocker (screw cement). Ball bearings are optional! (with optional part no.)

9 Front Suspension x 0mm TP x mm TP TP F/H Screw TP F/H Screw Note the direction. Front x0mm 5 xmm x0mm Center Gearbox Front x 6mm TP 8 (Silver) x 0mm TP 0 (Silver) 0 8 x 0mm x0mm x 0mm Metal Collar Screw 0 x 0mm Shaft 09 0 x mm Metal Bushing 8mm x6mm Aluminium Spacer x0mm Note the direction Center Gearbox x mm Set Screw 8 Note the direction for 8. x 8mm Screw 5 Brake Piston xmm Top.5mm approx..5mm xmm x8mm Firmly tighten the set screws onto the flat spots. 5 Apply threadlocker Ensure smooth non-binding Pay close attention Ball bearings are optional! Apply grease. (screw cement). movement while assembling. here! (with optional part no.) 9

10 6 Center Gearbox x 0mm TP TP F/H Screw 9 x0mm x0mm Rear Gearbox x 0mm TP TP F/H Screw x 0mm TP Front Note the direction. 0 x0mm x0mm x0mm ( ) (F/H) x0mm ( ) (F/H) 8 Front Suspension x 0mm TP TP F/H Screw x0mm x0mm Assemble in the specified order. 0

11 START No., 9 Front Suspension No. Note the direction. Inside Outside 0 x 0mm 9 6.8mm Adjustable Rod Ball x 0mm TP.8mm Ball x 5mm 5.8mm F/H Screw Flange Ball mm Flanged Nylon Nut x 0mm Set Screw mm A "A" marked 5 x 0mm Metal Bushing 8 6.8mm Ball End mm approx. 9mm 5.8mm Pillow Ball 6 Take care balls from any damage when assemble. B "B" marked 9 8 mm approx. mm x0mm Note the direction. x5mm Do not overtighten. Left mm Do not overtighten. Right 5 6 x5mm No., 0 Front Suspension No. x 5mm TP Right x 8mm F/H Screw x 8mm F/H Screw O O-ring Put O-rings on the left side. Put O-rings on the right side. Use inside hole. x8mm x8mm ( ) (F/H) Left x5mm Tentatively tighten. Part bags used. Ensure smooth non-binding Assemble left and right Pay close attention here! Apply grease. Apply threadlocker Ball bearings are optional! movement while assembling. sides the same way. (screw cement). (with optional part no.)

12 No., No., Rear Suspension No., No. Note the direction. Inside Outside x 5mm TP 66 Tapered Washer mm Flanged Nylon Nut mm 5 x 0mm Metal Bushing 5.8mm Pillow Ball Take care balls from any damage when assemble. 9 Left 8 6.8mm Ball End mm Ball 8 Use this hole. 5.8mm Flange Ball.5mm approx..5mm Left Screw Hub Pin 66 mm x5mm 8 5 Right No. Rear Suspension x 5mm TP x 8mm F/H Screw O O-ring Right Use O-rings for both side. Use inside hole. x5mm Left Use inside hole. x8mm Tentatively tighten. Part bags used. Ensure smooth non-binding Assemble left and right Pay close attention here! Apply grease. Apply threadlocker Ball bearings are optional! movement while assembling. sides the same way. (screw cement). (with optional part no.)

13 Steering No., No..6x6mm.6 x 6mm Screw Hex Wrench (small) 5.8mm Pillow Ball mm Nylon Nut x8x.5mm Plastic Bushing 8 C C marked mm Widen the slit with a screwdriver and fit in the snap Steering No., No mm Ball End 0 x 0mm Set Screw 0 x0mm mm approx. 0.5mm x Bumper No., No. x8mm x 8mm Screw x0mm x 0mm TP x Part bags used. Ensure smooth non-binding 9699 Ball bearings are optional! Assemble as many movement while assembling. (with optional part no.) times as specified.

14 6 Shock 5.8mm M Ball End (M) No.5 x.5mm approx..5mm 8 Shock Shaft G E.5 E E-ring mm L Ball End (L) 9 5 L Use 5.8mm Ball End (L) at the time of driving on off-road. Cover the shaft with cloth before gripping it with pliers. x Shock No.5 Oil G Pull down the piston 0 ~ mm and slowly fill in oil. 8 0 ~ mm 80 Add oil one more time up to the brim. Piston Then, gently move the piston up and down to get rid of air bubbles G Put 8 onto 9, wipe up any Ensure smooth piston excess oil and screw on G move-ment. together with 80. x 8 Shock 8 5.8mm Ball No.5 G6 Compress the spring and install G6. G8 G6 x 8mm F/H Screw 8 mmmm Use mm spacer for Front and mm spacer for Rear. 8 x8mm G G5 ~mm x x Part bags used. Assemble as many times as specified.

15 9 Front Shock 0 Rear Shock Use the upper hole. No.5 mm Install mm spacer only the left. Bumper No.,No. x0mm x0mm x 0mm TP xmm Remove both screws and reinstall together with. Part bags used. Assemble left and right sides the same way. Pay close attention here! 5

16 Fuel Tank No., No.6 6 0mm Silicone Tube Cut to one 0mm piece. 6 Silicone Tube 0mm Cut to one 0mm piece. 5 6 Use in. x 0mm TP TP F/H Screw x0mm 0mm 0mm 5mm Engine No. Tighten the screws with one sheet of paper inserted between both gears. Engine Assembly Included engine has no screws to adjust Air/Fuel Mixture at slow engine speed. x 8mm Screw x8mm x8mm Part bags used. Cut off excess. 6

17 Muffler No., No Front View mm 5 5 Assemble muffler like the picture xmm x 0mm Screw xmm x 8mm F/H Screw x mm Set Screw mm Nut x8mm x0mm 5 Radio No., No. Throttle Servo x 0mm x 0mm TP 0 TP TP F/H Screw Steering Servo x0mm x0mm 5 x 5 x0mm x0mm ( ) (F/H) x0mm x0mm ( ) (F/H) Part bags used. Cut off excess. Must be purchased separately! x Assemble as many times as specified.

18 6 Radio No. Receiver Battery Box Switch Switch 55 Switch Radio No. Connect as per radio instruction manual. x 0mm TP TP F/H Screw Antenna Receiver x0mm x0mm 8 Radio x 8mm TP No., No. x8mm 58 Antenna 5 Hook Pin 5 x8mm 56 Make sure to place the cord inside of the box. Part bags used. Must be purchased separately! Pay close attention here! 8

19 No., No. 9 Radio Supplied with the servo Steering Rod x mm Set Screw xmm mm The hole used. mm approx.mm 0 Radio No., No. 0mm Bend. x 8mm TP x mm Set Screw 60 mm Stopper 6 xmm 60 x8mm xmm Note the top and bottom. 6 Spring Holes used. 6 Throttle Rod 6 Brake Rod 6 Servo Horn mm 0mm approx.0mm 6mm approx. 6mm Radio x mm Set Screw 66 Tapered Washer 65 No., No. 6mm Supplied with the servo. Link to the bottom hole. xmm 5 Neutral Brake Lever Note the direction mm Silicone Tube (5mm) Part bags used. Must be purchased separately! Assemble in the specified order. Ensure smooth non-binding movement while assembling. mm Cut off shaded portion. Pay close attention here! mm Drill holes with the specified diameter. True-to-scale diagram. Tentatively tighten. 9

20 No. Throttle Linkage Adjustment ( ) ( ) ( Neutral ) ( High ) mm Adjust with throttle approx.mm stop screw. ( ) ( Brake ) Brake works properly? mm approx.mm Contracted. a b 8 85 Confirm the setting 86 before installation. 8 Carburetor open fully? Throttle Stop Screw Replace air cleaner to Position where brake starts working. No.965 Air Cleaner a,b (option) at the time of Set up a and b screws as shown. driving on off-road. No.,No. Front Body Mounts 9 8 x8mm x 8mm TP x 0mm TP 9 x8mm x0mm No.,No. Rear Body Mounts No.6,No..6 x 6mm TP x 5mm TP 5.8mm Pillow Ball 0 xmm 9 60mm approx. 60mm 9 9 x8mm x5mm 9.6x6mm x5mm 5 x8mm mm Ball End x 8mm TP 0 x mm Rod 6.6x6mm Part bags used. Cut off excess. Assemble left and right sides the same way. Cut off shaded portion. 0

21 5 Wheels Note the direction. x For Right x For Left Fit wheels inside tyres as shown. Twist the tyre onto the wheel. After fitting wheels to tyres, apply instant glue as shown. 6 Wheels No. < Rear > Hold the shaft tight with a hex wrench to tighten the nut. < Front > mm For Rear mm For Front Cross Wrench Remove this nut from the chassis and fasten the tire with it. Cross Wrench Body Shell 6mm 6mm mm 6mm mm mm mm 6mm x Apply rubber type glue. Apply instant glue Assemble as many Assemble left and right Cut off shaded 6mm Drill holes with the (CA glue, super glue). times as specified. sides the same way. portion. specified diameter.

22 8 Painting Before painting, use a neutral detergent to remove any oil residues and dirt. Mask the windows from the inside. Refer to the pictures on the box for the color scheme. After painting, remove the protective film from the body shell. Paint the body shell from the inside using Kyosho s spray colors. No.6 Italian Red Mask Windows Italian Red Mask Windows Italian Red Italian Red 9 Body Shell x8mm mm x 8mm Screw mm mm Washer 8 mm Nut x8mm mm mm mm mm

23 0 Decals Apply the decals to the positions indicated in numerical order. The decal numbers between brackets are only for the opposite side ( ) 9 ( 0 ) ( ) ( ) ( ) 5 55 Body Shell No Slightly bend the body pins as shown in the diagram for easier removal. 5 Body Pin Always run your car with the body shell mounted! Do not run your car on ground: Safety Precautions that is overgrown with grass. that is muddy, sandy or rocky. Check all screws, nuts etc. on a regular basis for looseness. Part bags used.

24 OPERATING YOUR MODEL SAFELY In order to avoid accidents and personal injury, be sure to observe the following: Since exhausts and fuel vapors are noxious to health, use fuel only outdoors! Keep hands and objects away from rotating engine parts to avoid personal injury. Because after running the engine, the engine and the muffler are extremely hot, beware of getting burned! For accident prevention, do not run your model under Only use glow fuel for radio control models! Never use the following circumstsnces: gasoline or kerosene which might cause accidents such as fires! In place where many people gather. Near residential districts, schools and hospitals. Because fuel is highly inflammable, never use fuel indoors, near any source of heat, open flames or even Near roads, railroads, air corridors and electric lines. sparks! Do not dispose of an empty fuel can into a fire. It might explode causing serious injury! Also make sure that nobody is using the same frequency as you do at the same time! Be particularly careful not to swallow fuel or to get fuel When the radio batteries are empty. into eyes! Nevertheless, should fuel be swallowed, immediately induce vomiting and call a physician. When the model's control or running behavior is Should fuel get into eyes, thoroughly rinse the eyes strange. and seek medical advice. Always store fuel in a safe place out of children's reach with the cap shut tight! The place for storage should be dark, cool and dry!

25 SPARE PARTS FOR JAPANESE MARKET ONLY. No. No. No. Part Names Quantity No. Part Names Quantity 6.8mm x0mm BS6 6.8mm Ball 9 x x0mm Set Screw 0 x DX x0mm BS5 Clutch Shoe (DX) x x x0mm Set Screw x 00 BV5 Servo Saver 5 6 x x mm mm mm Swingshaft (mm) 9 x 00 FD Flywheel Set x mm 5.8mm Pillow Ball x 8 00 FD9 FD65 6.8mm Fuel Tube 6 x mm Ball End 8 x GP x 00 S Linkage Set (for GP cars) x 6 6 x KP/KY Fluorescent Strap (S) x FM Clutch Bell 5T (5T) x 00 0 KP/KY M Fluorescent Strap (M) 9 x 0 50 FT5 Suspension Arm Set 6 0 x Color Antenna (White) 58 x FT Knuckle Arm 5 6 x x0mm 5x0mm Metal Bushing x 0 00 FT Body Mount 8 0 x 9 x xmm 8xmm Metal Bushing 09 0 x FZ0 Gear Box 06 0 x Muffler Gasket x 5 00 FZ EVO.VII Final Differential Case 0 05 x Body Set (MITSUBISHI LANCER EVO.VII) body, decals 00 FZ9 EVO.VII Swing Shaft x x Decal Set (MITSUBISHI LANCER EVO.VI) decals 000 FZ58 GS5R Center Bulkhead 6 0 x GS5R Engine 50 x 000 FZ6 9T xmm Spur Gear (9T) 8 9 x xmm Rod 0 x 00 FZ6 FZ6 FZ0 LA8 LA Disk Holder x Muffler Post Set 5 5 x 5cc Spur Gear Shaft 0 x cc Fuel Tank 5 x Brake Lever 65 5 x Screw Hub Pin x Rear Hub Carrier 8 9 x Low Profile High-Grip Tire x 5.8mm 5 5.8mm Ball End 9 x Low Profile Wheel (5-spoke) x LD0 Clutch Bearing 6 8 x BK Heat-resistant Muffler Joining Pipe 50 x 800 GT5 OT5 OT8 OT9 Pilot Shaft x Snap Pin 5 x 0 t Joint 08 x Steel Drive Washer (t) x OT6 Differential Gear Set 0 0 x 0 x Swingshaft (OT6) x O O-ring x Disk Brake Pads 8 x RM Air Filter (AB5) AB5 x0mm x x0mm Rod 0 x 00 TRB.8mm Main Chassis 5 x mm Flanged Ball 5 x 500 TR.8mm Front Bulk Set x mm Ball x 0 00 TR SS Rear Bulk Set 6 0 x 5 x SS Tuned Muffler 5 x 00 TR5 Steering Plate Set 8 6 x x Manifold 8 x 600 TR6 Receiver Box x 600 TR8 S Upper Rod (S) x 00, TR0 Bumper, Rear Body Mount 5 x x 00 Some of the parts included are not available as spare parts. Purchase optional parts instead. TR Wheel Shaft x 00 UM VZ0 BK W50 W56 Servo Saver Reinforcing Ring x Urethane Bumper (Black) x M,L Shock End (M,L) x SS x Racing Shock (SS) x

26 FOR JAPANESE MARKET ONLY. No. No. No. Part Names Quantity No. Part Names Quantity & + FD0 Engine Mount for optional engine Locking Jig & Wrench Cross wrench + plug locker CZ-R O.S.CV FD9 Flywheel (CZ-R) for O.S. CV type engine Maintenance Stand 800 FZW Steel Differential Bevel Gear strengthened gear Onroad Spring Set (Hard Type) instead of 8. types. 800 FZW5 05, Steel Differential Pinion Gear strengthened gear High Ratio Steel Final Gear instead of 05,. 800 FZW8 FZW0 FZW56 FZW6 KC5 SPW5 S 8 Steel Differential Gear Set Steel type Differential Gear Onroad Spring Set (S) instead of 8. types cycle Fitting Kit mm When Mounting -cycle Engines Titanium Adjust Rod 0mm 600 pcs. for Tie Rod No T -Speed Automatic Transmission Set Only for on road One-piece Clutch Bell 5T Need to purchas separatly. 600 FZW56 No T Braking Center Oneway Only for FZW One-piece Clutch Bell 6T Need to purchas separatly. 600 No T Special Clutch instead of One-piece Clutch Bell T Need to purchas separatly. 600 No T Stainless Disk Rotor high performance disk rotor One-piece Clutch Bell 8T Need to purchas separatly. 600 TRWB TRW W555 SP 5 / Special Main Chassis instead of Low Profile Wheel (mesh-type, white) 5x0mm 8xmm / Ball Bearing Set 5x0mm pcs. 8xmm S Low Profile Wheel (mesh-type, silver) SS 966 / Adjustable Teflon Shock (SS) 00 BK Low Profile Wheel (mesh-type, black) mm / 968 K-ZERO5R KP/KY 5.8mm Ball End Fluorescent Pink / Fluorescent Yellow 00 5R K-ZERO Slick Tire 5R K-ZERO5Z Color Antenna (Pink) instead of K-ZERO Slick Tire 5Z K-ZERO0Z Molded Mesh Color Antenna (Yellow) instead of K-ZERO Slick Tire 0Z High Grip Tires K-ZERO0V Color Antenna (Black Cap) instead of V K-ZERO Slick Tire 0V 968 K-ZERO0Z Special Antenna Holder aluminum K-ZERO Slick Tire 0Z / KP/KY Color Silicone Tube Fluorescent Pink / Fluorescent Yellow Dual Spring Set Air Cleaner Oil Loctite (medium strength) Screw cement. 900 R Super Tuned Silencer R Set Gives an increase in engine power One-touch Plug Heat Set booster cord, Ni-Cd battery, charger M 50cc Fuel Filter (M) Shuts out dirt from fuel Quick Fill Fuel Bottle (50cc) aid for fueling 500cc Steel Final Differential Case Quick Fill Fuel Bottle (500cc) aid for fueling 5x0mm Cooling Fan Set x0mm Ball Bearing pcs. 8, 85, 86, 8 5x8mm Air Cleaner instead of 8, 85, 86, x8mm Ball Bearing pcs. O.S. 8xmm Special Engine Mount When Mounting O.S. Engines xmm Ball Bearing pcs Vespel Clutch Shoe High strength clutch shoe 500 XR6 50 Servo Saver Ues with No.9655 SC Spring Connect Super Tuned Muffler spring connect type Special Unicrank Ues with No.XR6 95 Servo Saver Reinforcing Spring instead of # HG 6v X-FORCE #000 HG Joint Grease 6 6v X-FORCE 600 Ni-Cd Battery for receiver Differential # SP GS-5R GS-5R 9650 Gear Grease #5000 Oneway Bearing Grease -BL SP Cylinder Head (GS-5R) for GS-5R #0000 FOR JAPANESE MARKET ONLY. No. Part Names Qty. No. Part Names Qty. No. Part Names Qty Silicone Oil (00) Silicone Oil (600) 965 Silicone Oil (000) for shocks Silicone Oil (50) 9660 Silicone Oil (800) 9696 Silicone Oil (0000) Silicone Oil (00) 965 Silicone Oil (000) 9696 Silicone Oil (0000) for diffs Silicone Oil (50) 965 Silicone Oil (000) 9696 Silicone Oil (50000) for shocks Silicone Oil (00) Silicone Oil (000) 9696 Silicone Oil (00000) for diffs Silicone Oil (50) 965 Silicone Oil (000) Silicone Oil (0000) Silicone Oil (00) 9655 Silicone Oil (5000) Silicone Oil (500) 9656 Silicone Oil (6000) 6 OPTIONAL PARTS

27 Round Head Screw 0 x6 x8 x0 x5 5 each 0.6x8.6x0.6x.6x 5 each 0 x x6 x8 x0 x 5 each 0 x x6 x8 x0 5 each 05 x6 x8 x0 x 5 each 06 x x x6 x8 5 each Bind Screw 0.6x.6x6.6x8.6x 5 each x x6 x8 x0 x 5 each x x6 x8 x0 5 each x6 x8 x0 x 5 each x x5 x8 x0 5 each 5 x5 x8 x0 x 5 each Flat Head Screw 8.6x8.6x0.6x.6x 5 each 9 x6 x8 x0 x 5 each 0 x x6 x8 x0 5 each x8 x0 x5 x0 5 each x x x6 x8 5 each x0 x x x5 5 each Cap Screw x8 x0 x x each 5.6x8.6x0.6x.6x each 6 x8 x0 x x each x5 x6 x8 x0 each 8 x5 x0 x5 x0 each 9 x0 x5 x0 each 0 x5 x8 x0 each x5 x0 x5 each SCREW NUT etc. Ø Nut x x6 x8 x0 5 each.6x6.6x8.6x0.6x 5 each x6 x8 x0 x x 5 each 5 x5 x6 x8 x0 5 each 6 x5 x0 x5 5 each.6x.6x5.6x6.6x8 5 each 0.6x6.6x8.6x0.6x 5 each x6 x8 x0 x x 5 each x5 x6 x8 x0 5 each x0 x5 x8 5 each Flat Head Self-Tapping Screw.6x6.6x8.6x0.6x 5 each 8 x6 x8 x0 x x 5 each 9 x5 x6 x8 x0 5 each 50 x5 x0 x5 5 each Flanged Cap Screw 5 x6 x8 x0 each 5 x8 x0 x each Screw 5 x8 x0 0 each Set Screw 60 x6 x x x6 each 6 x x x5 x0 each 6 x x5 x8 x each 6 5x 5x5 5x6 each 6 5x0 5x0 each mm.6mm 0 each mm mm 0 each Flanged Nut mm 0 pcs 5 mm 0 pcs Nylon Nut.6mm 5 pcs 8 mm 5 pcs 9 mm 5 pcs Flanged Nylon Nut 80 mm 5 pcs Washer 85 mm.6mm mm 0 each 86 mm 5mm 0 each 80 E.5 0 pcs 8 E.0 0 pcs 8 E.5 0 pcs 8 E.0 0 pcs 8 E.0 0 pcs 85 E5.0 0 pcs 86 E6.0 0 pcs 8 E.0 6 pcs 90 E0.0 6 pcs

28 GP TR-5 Rally WD 00 KYOSHO / EXPLODED VIEW < > Parts indentified only by key numbers are not sold individually 8 9 W56 W FT5 0 LA N I BS6 9 W56 G8 W56 8 BS FD TR FZ9 TR8 TR OT OT8 FZ FZ 96 8 O FZ0 OT9 0 TR TR 0 OT5 08 FZ0 06 OT LA Q Q O P M OT BK 50 FD65 66 FD9 6 FD65 6 LA 9 LA KP/KY 0KP/KY H FD9 6 RM FD9 6 W56 G8 90 TR5 OT5 08 TR5 TR 96 OT TR5 6 8 OT5 08 TR FZ0 0 OT9 FT G J F A C E 5 5 FZ OT8 FZ FZ0 FZ FZ0 06 BS FZ9 8 OT TR 96 FT BS6 9 8 FT5 6 B FT5 FT5 FZ0 5 FZ58 0 FZ6 9 LD0 8 LD0 6 BS5 BS5 GT5 FD FZ58 FZ6 8 FZ FZ58 FM 65 FZ58 6 L TR6 56 TR E 0 0 K 8 8 P W56 8 W56 G W56 8 W56 80 G6 8 G 9 G 8 8 G FD65 6 FD65 6 FD65 6 FD65 60 FD65 6 TR 5 TR 5 TR 5 TR 5 FD65 60 TRB 5 N M I L K H G B C R D FD TR LA 9 FD TR5 8 LA 9 LA 9 BV5 BV5 8 8 LA 9 D TR BV5 UM BV5 5 6 F TR0 VZ0BK TR0 5 TR0 TR J W56 8 W56 G8 W56 80 W56 W50 G 9 G 8 8 G 8 G6 R A FT FT 9 0 OT9

29 R THE FINEST RADIO CONTROL MODELS R/C -00 ( PRINTED IN JAPAN