00.cdr

Transcription

1 PROFILCO UNIVERSAL JUNE- 2005

2

3 PROFILCO UNIVERSAL ﾁ ｨ ｨｦ090208ｨ ｨｬｨ ｨｰ ｨｪ00ｨ ｨｰ 0007 ｨｮ05ｨｮ0004ｨｬｨ ISO 9001, 01ｨｦ02ｨｪ ﾂ07 ｨｮ00ｨ ｨｲｨｹｨｪ00ｨ ｨｮ ｨｬ07ｨｬｨ 04ｨ 09ｨ 00ｨｴ0007ｨｰ ｨｺｨ ｨｦ ｨｬ07ｨｬｨ 0407ｨｦ0700ｨｦｨｺ ﾂ ｨｮ02ｨｦ ｨｦｨ 0009ｨ 0206ｨｪ , ｨｺｨ ｨｦ DIN ｨｦｨ 00ｨ 0002ｨｴｨｬ020009ｨｦｨｺ05 ﾂｨ 09ｨ ｨｺ000409ｨｦｨｮ00ｨｦｨｺ ｨ ｨｺｨ ｨｦ QUALICOAT ｨｹｨｮ07ｨｪ ｨ ｨｪ 0208ｨｦｨｺ ｨｰ. QUALITY CONTROL METHODS FOR EXTRUDED PROFILES AND POWDER COATINGS Our company abides ISO 9001 system carry out tests on the extruded profiles by the Department of Production and Quality Control of our company, implementing ISO 9001 system, carries out tests on the extruded profiles. The tests have been done by the specifications of ELOT EN , and DIN and those of QUALICOAT for the powder coating ｨｦｨ ｨ 09ｨ 00ｨｴ ｨｴｨｪ ﾂ0904ｨｮｨｦｨｬ070807ｨｦ020800ｨ ｨｦ ｨｺ0905ｨｬｨｬｨ W 6063 (Al Mg 0.7Si) ｨｬ02 00ｨ 08ｨ 09ｨ ｨｺ0500ｨｴ 0002 ﾂｨｪｨｦｨｺ05 ﾂｨ 09ｨ ｨｺ000409ｨｦｨｮ00ｨｦｨｺ05: ｨｬｨｦｨｺ07 ｨｺｨ ｨ ｨｮ08ｨ : ｨｦ07 01ｨｦｨ ｨｰ: R P0.2= 0 00pa (min) 0409ｨｦ07 ｨｨ09ｨ 05ｨｮ04ｨｰ: R m= pa (min) 3 03ｨｦ01ｨｦｨｺｨｹ ｨｰ:Y= 2,69 gr/cm 2 M ｨ ｨｮ00ｨｦｨｺｨｹ000400ｨ ｨｰ: 03 = N/mm 0701ｨｪ ｨｮ0007ｨｰ 0009ｨ ｨｬｨｬｨｦｨｺ07ｨｰ 01ｨｦｨ ｨｮ ｨｰ: -6 ｨ = 2,34x10 / K 04ｨ 09ｨ ｨｬｨｹ0902ｨｴｨｮ04 ｨｨ09ｨ 05ｨｮ04ｨｰ:09 mm%= 6(min) ﾁ ｨｦｨ ｨｮ0005ｨｮ02ｨｦｨｰ 03ｨｦ 01ｨｦｨ ｨｮ0005ｨｮ02ｨｦｨｰ (0805 ﾂ07ｨｰ ｨｺｨ ｨｦ ｨｹ0502ｨｰ 07ｨｦ 0108ｨｹ0507ｨｦ0802ｨｰ 01ｨｦｨ ｨｮ0005ｨｮ02ｨｦｨｰ) ｨ ｨｺ ｨｨ0705ｨｪ 00ｨｦｨｰ ｨｦｨ 0009ｨ 0206ｨｰ ﾂ. 0205ｨｪ 06 ﾂ0701ｨｬ02 ｨｬｨｦｨ 07ｨｪ07ｨｬｨ ｨｮ00ｨｦｨｺ07 01ｨｦ05ｨｮ00ｨ ｨｮ04 55 ﾂｨｦ ｨｪ0200ｨ ｨｦ ｨ ｨｪ07 ﾂ07 (+/-) 0,40 ﾂｨｦ ｨｮ04ｨｬｨ 08ｨｪ02ｨｦ ｨｹ00ｨｦ ｨｺ01ｨｬｨ 08ｨｪ0200ｨ ｨｦ ｨ 08ｨｹ 54,60 06ｨｴｨｰ 55,40 ﾂｨｦ ｨｴｨｮ ｨｬ02ｨｴｨｪｨ ｨｬ02 00ｨｦｨｰ ｨｦｨ 0009ｨ 0206ｨｰ ｨｦｨ 06ｨｪｨ ｨｬ ｨｰ ｨｬ06 ﾂ09ｨｦ 75 ﾂｨｦ ｨ 08ｨｹｨｺ05ｨｦｨｮ ｨｪｨ ｨｦ 2 ﾂｨｦ05. 01ｨｦｨ ｨｪｨ ﾂｨｨ ｨｮ ｨｴｨｮ ｨｦ ｨ ｨｪｨ ｨｨ020004ｨｨ0208 ｨｮ ｨｺ07 ｨｺｨ ｨｦ ｨｪｨ ｨｬ ｨｨ ｨｬ0600ｨｦｨｮ0004 ｨ 08ｨｹｨｮ00ｨ ｨｮ04 ｨｮ ｨｦ ｨｮ04ｨｬ ｨｰ ｨ ｨｰ ｨｬ0200ｨ ｨｰ ｨｺ0500ｨｴ 0208ｨｦ0205ｨｪ02ｨｦｨ ｨｰ ｨ ｨｰ ｨｺｨ ｨｦ ｨｺ ALUMINUM PROFILES Alloy ENAW 6063 (Al Mg 0.7Si) used for the production of profiles has the following technical characteristics: Heat treatment: T5 0.2% Proof Strength: R P0.2= 0 00pa (min) Ultimate strength: R m= pa (min) 3 Density:Y= 2,69 gr/cm 2 Elastic modulus: 03 = N/mm Coefficientlinear expansion: -6 ｨ =2,34x10 /K Minimum elongation:09 mm% = 6 (min) GEOMETRICAL CHARACTERISTICS Dimensions The tolerances of dimensions (wall thickness and all the rest dimensions) follow the specifications of EN e.g. if we have 55 mm dimension the tolerance is (+/-) 0.40 mm, which means that the dimension is between 54,60 and 55,40 mm. Twist By the specifications of E for a profile bar with width no more than 75 mm the deviation is 2 mm. The twist is measured by placing the bar on a flat base plate and measuring the maximum distance at any point along the length between the bottom surface of the bar and the base plate surface. 50 JUNE A1

4 PROFILCO UNIVERSAL 0301ｨｨ ｨ 0705ｨｬ02ｨｴｨｪｨ ｨｬ02 00ｨｦｨｰ ｨｦｨ 0009ｨ 0206ｨｰ ｨｦｨ ｨｬｨｦｨ ｨ 6 ｨｬ060009ｨｴｨｪ, ｨｦ ｨｹｨｬ02ｨｪ ｨｰ 0208ｨｪｨ ｨｦ 3 ﾂｨｦ05. ｨｺｨ ｨｦ ﾂ07ｨｰ 0008ｨｪ0200ｨ ｨｦ ｨｮ ｨｪ00ｨ ｨｰ ｨ ｨｮ00ｨｦｨｰ ｨｺ0902ｨｰ 0004ｨｰ 0805ｨｪｨｴ ｨｮ02 06ｨｪｨ ｨｪ ｨｺ ｨｰ ｨｮ0004 ｨｬ06ｨｮ ｨｰ ｨ ｨｰ 0102ｨｪ ｨｦ ｨｪｨ 0208ｨｪｨ ｨｦ 0805ｨｪｨｴ ｨ 08ｨｹ 3 ﾂｨｦ05. 07ｨｺ050409ｨｹ000400ｨ H ｨｮｨｺ050409ｨｹ000400ｨ 00ｨｴｨｪ ﾂ0200ｨ ｨｦ ｨｮ05ｨｬ02ｨｴｨｪｨ ｨｬ02 00ｨｦｨｰ ｨｦｨ 0009ｨ 0206ｨｰ 0301 ISO ｨｬ0205ｨｪｨｦｨｮ ｨｦｨｺ ｨｴｨｪ ｨｮ04ｨｬｨ ｨｪ00ｨｦｨｺ06ｨｪ 0208ｨｦ02ｨ ｨｪ02ｨｦ06ｨｪ ｨ ｨｦ ｨｺ0500ｨｴ ｨ 08ｨｹ ｨｦｨｺ07 00ｨｴｨｪ08ｨ 60 ｨｺｨ ｨｦ ｨ 08ｨｹｨｮ00ｨ ｨｮ04 2 ｨｬ060009ｨｴｨｪ (07ｨｦ ｨｦｨ 0009ｨ 0206ｨｰ QUALICOAT ｨ ｨｪｨ ｨｪ 3 ｨｬ060009ｨ ). 0202ｨｪ ｨｦ ｨｪｨ 0208ｨｪｨ ｨｦ 0709ｨ ｨ ｨｬｨ 00ｨ ｨｹ08ｨｴｨｰ: 02ｨｬ0205ｨｪｨｦｨｮ ｨ ｨｰ ｨｺｨ 05ｨｦ0705, ｨｮ000800ｨｬｨ 00ｨ, ｨｬ08ｨｦｨｬ0808ｨｺｨｦｨ, ｨｺ09ｨ ｨｰ, ｨｺ Straightness By the specifications of E for a 6 meter bar the allowed deviation from straightness is 3 mm and is measured with the profile bar placed on horizontal base plate, so that its own mass decreases the deviation. The deviation in the middle of the bar must not exceed the 3 mm. Hardness The profile's hardness is tested by the specifications of EN ISO ELECTROSTATIC COATING Appearance The coating on the significant surface is 0 viewed at an oblique angle of about 60 and at distance of 2 meters. (The specifications of QUALICOAT mention 3 meters). Excessive roughness, runs, blisters, inclusions, craters, dull spots, pinholes, pits, scratches must not be visible from this distance. 0908ｨｹ0507ｨｦ0807ｨｦ ｨｹｨｬ02ｨｪ07ｨｦ ﾂ07ｨｦ ﾂ07ｨｰ ﾂ0701ｨｰ 0208ｨｦｨｺ ｨｰ ｨｺｨ ｨｦ 07ｨｦ 01ｨｦ ｨｰ ｨｬ04 ﾂｨ ｨｪｨｦｨｺ06ｨｰ ｨｺｨ ｨｦ ﾂ04ｨｬｨｦｨｺ06ｨｰ 0107ｨｺｨｦｨｬｨ ｨｮ0802ｨｰ 01ｨｦ02ｨｪ ｨｪ00ｨ ｨｦ ｨ 08ｨｹ 0007ｨｪ 0407ｨｦ0700ｨｦｨｺｨｹ ﾂ07 ｨｬ ｨｦ01ｨｦｨｺ0201ｨｬ06ｨｪ ｨｮｨｴ08ｨｦｨｺｨｹ ｨｺｨ ｨｦ ｨｮ ｨｦｨｮｨｬ06ｨｪｨ ｨ ｨｮ000709ｨｦｨ. 01ｨｦｨ ｨｰ 08ｨ 09ｨ 0805ｨｪｨｴ ﾂ0701ｨｰ ｨｺｨ ｨｦ 0107ｨｺｨｦｨｬ06ｨｰ ｨ ｨｺ ｨｨ0705ｨｪ00ｨ ｨｦ 07ｨｦ ｨｦｨ 0009ｨ 0206ｨｰ QUALICOAT ｨｺ0508ｨｮ02ｨｦｨｰ ｨｰ ｨｬ02ｨ ｨｪ ｨ ｨｦ ｨｮ0007ｨｪ ｨｺｨ ｨｪｨ ｨｦ 0007 ｨｨ02ｨｴ090400ｨｦｨｺｨｹ ｨｰ ｨ ﾂ0701ｨｪ ｨ 0807ｨｺ0508ｨｮ02ｨｦｨｰ ｨｬ0200ｨ ｨｨ02ｨｴ090400ｨｦｨｺ0705 ｨｺｨ ｨｦ ｨ 00ｨｬｨ 00ｨｦｨｺ ｨｰ ｨｪ0701ｨｪ 0007 (+/-) 6% 02ｨｪ ｨｮ00ｨｦｨｨ06ｨｬ02ｨｪ ｨｰ ｨ 08ｨｹ 0004ｨｪ 09ｨ ｨｪ02ｨｦ ｨｮ ｨｰ %. Rest regulation tests The Quality Control Department, with specialized technical stuff in a well-equipped laboratory, carries out the coating thickness tests as well as several chemical and mechanical tests. For the above-mentioned tests the QUALICOAT specifications are followed. Tolerances Weight that is shown in present catalogue, is the theoretical weight of mill finish profile. There is a tolerance between the theoretical and the actual weight, which is up to (+/-)6%, and the additional weight due to color is up to 3-4 %. A2 JUNE

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

25

26

27

28

29

30

31

32

33

34

35

36

37

38

39

40

41

42