WOUND CHIP INDUCTORS LB SERIES OPERATING TEMP. 2 Including self-generated heat FEATURES Rdc LB/LBRRdcIdc LBCIdcRdc LB LBMF Wound Chip Ind

Size: px
Start display at page:

Download "WOUND CHIP INDUCTORS LB SERIES OPERATING TEMP. 2 Including self-generated heat FEATURES Rdc LB/LBRRdcIdc LBCIdcRdc LB LBMF Wound Chip Ind"

Transcription

1 Notice for TAIYO YUDEN products Please read this notice before using the TAIYO YUDEN products. REMINDERS Product information in this catalog is as of October All of the contents specified herein are subject to change without notice due to technical improvements, etc. Therefore, please check for the latest information carefully before practical application or usage of the Products. Please note that Taiyo Yuden Co., Ltd. shall not be responsible for any defects in products or equipment incorporating such products, which are caused under the conditions other than those specified in this catalog or individual specification. INFORMATION ON THE GENERAL CATALOG Please contact Taiyo Yuden Co., Ltd. for further details of product specifications as the individual specification is available. Please conduct validation and verification of products in actual condition of mounting and operating environment before commercial shipment of the equipment. All electronic components or functional modules listed in this catalog are developed, designed and intended for use in general electronics equipment.(for AV, office automation, household, office supply, information service, telecommunications, (such as mobile phone or PC) etc.). Before incorporating the components or devices into any equipment in the field such as transportation,( automotive control, train control, ship control), transportation signal, disaster prevention, medical, public information network (telephone exchange, base station) etc. which may have direct influence to harm or injure a human body, please contact Taiyo Yuden Co., Ltd. for more detail in advance. Do not incorporate the products into any equipment in fields such as aerospace, aviation, nuclear control, submarine system, military, etc. where higher safety and reliability are especially required. In addition, even electronic components or functional modules that are used for the general electronic equipment, if the equipment or the electric circuit require high safety or reliability function or performances, a sufficient reliability evaluation check for safety shall be performed before commercial shipment and moreover, due consideration to install a protective circuit is strongly recommended at customer's design stage. The contents of this catalog are applicable to the products which are purchased from our sales offices or distributors (so called TAIYO YUDENs official sales channel). It is only applicable to the products purchased from any of TAIYO YUDENs official sales channel. Please note that Taiyo Yuden Co., Ltd. shall have no responsibility for any controversies or disputes that may occur in connection with a third party's intellectual property rights and other related rights arising from your usage of products in this catalog. Taiyo Yuden Co., Ltd. grants no license for such rights. Caution for export Certain items in this catalog may require specific procedures for export according to Foreign Exchange and Foreign Trade Control Lawof Japan, U.S. Export Administration Regulations, and other applicable regulations. Should you have any question or inquiry on this matter, please contact our sales staff. Should you have any question or inquiry on this matter, please contact our sales staff. Please read the "Notice for TAIYO YUDEN products" before using this catalog. 3

2 WOUND CHIP INDUCTORS LB SERIES OPERATING TEMP. 2 Including self-generated heat FEATURES Rdc LB/LBRRdcIdc LBCIdcRdc LB LBMF Wound Chip Inductors that cover customers' wide range module design by wide-line-up shape, standard, low Rdc, and high electric current series. LB/LBR Series Super low Rdc and high Idc characteristics. LBC Series Super high Idc and low Rdc characteristics. LB328 Series This series are down sized from 3 size. Land pattern can be used by 3 size. LBMF608 Series The best efficiency design is achieved by adopting bottom-surface electrode structure. Because of 608 shape, it can be high-density mount. APPLICATIONS DSC / DVC / HDD DSC/DVC/HDD, LCD, portable telephones, game equipments. Various audio-visual equipments, various communication equipments, etc. ORDERING CODE LB 2 C R MF Rdc 3 mm T L B T H R0 R 6 K M 7 R 8 20 Rdc LB 2 Shape C R MF Wound chip inductor Standard products High current Low Rdc Bottom-surface electrode 3 External Dimensions mm Packaging T Tape & Reel Nominal H example R0 *R=decimal point 6 s % K M 20 7 Special code Standard products R Low Rdc type 8 Internal code Standard Products Blank space 2 Please read the "Notice for TAIYO YUDEN products" before using this catalog.

3 EXTERNAL DIMENSIONS L W T e LB Recommended Land Patterns LB28 LBC28 LBR28 LB206 LBC206 LB202 LBC202 LBR202 LB608 LBMF Unit mminch Surface Mounting Mounting and soldering conditions should be checked beforehand. Applicable soldering process to this products is reflow soldering only. Recommended Land Patterns Unit mm A B A C TYPE A B C MF AVAILABLE INDUCTANCE RANGE Range LB328 LB28 LB206 LB202 LB608 LBC28 LBC206 LBC202 LBR28 LBR202 LBMF608 ImaxmARdc30 ImaxmARdc30 ImaxmARdc30 ImaxmARdc30 ImaxmARdc30 ImaxmARdc30 ImaxmARdc30 ImaxmARdc30 ImaxmARdc30 ImaxmARdc30 ImaxmARdc30 H H H H H H H H H H H H H H H H H H H H H 24 0H 680H Examples Imax Rdc30% Imax Rdc30% Imax Rdc30% Imax Rdc30% Imax Rdc30% Imax Rdc30% Imax Rdc30% Imax Rdc30% Imax Rdc30% Imax Rdc30% Imax Rdc30% ma ma ma ma ma ma ma ma ma ma ma H H H H).8H H 2.H 0H Selection Guide Part Numbers Electrical Characteristics Packaging Reliability Data Precautions P.4 P.4 P.8 P.73 P.74 P.84 etc Please read the "Notice for TAIYO YUDEN products" before using this catalog. 3

4 PART NUMBERS LB608 TYPE L B 608 T R 0 M L B 608 T 2 R 2 M L B 608 T 4 R 7 M L B 608 T 8 R 2 M L B 608 T 0 0 M Environmental Substances H MHz min Rated current ma max MHz 7.96 LB202 TYPE L B 202 T R 0 M L B 202 T 2 R 2 M L B 202 T 3 R 3 M L B 202 T 4 R 7 M L B 202 T 6 R 8 M L B 202 T 0 0 L B 202 T 0 0 R L B 202 T 0 L B 202 T L B 202 T L B 202 T L B 202 T 0 Environmental Substances H MHz min Rated current ma max MHz LB206 TYPE L B 206 T R 0 M L B 206 T R M L B 206 T 2 R 2 M L B 206 T 3 R 3 M L B 206 T 4 R 7 M L B 206 T 6 R 8 M L B 206 T 0 0 L B 206 T 0 L B 206 T L B 206 T L B 206 T L B 206 T L B 206 T 0 Environmental Substances H MHz min Rated current ma max MHz LB28 TYPE L B 28 T R 0 M L B 28 T R M L B 28 T 2 R 2 M L B 28 T 3 R 3 M L B 28 T 4 R 7 M L B 28 T 4 R 7 M R L B 28 T 6 R 8 M L B 28 T 0 0 L B 28 T 0 L B 28 T L B 28 T L B 28 T L B 28 T L B 28 T 0 L B 28 T L B 28 T 2 2 L B 28 T 3 3 L B 28 T 4 7 L B 28 T 6 8 L B 28 T 0 2 Environmental Substances H MHz min Rated current ma max MHz Pleasespecifythetolerancecode K or M 4 Please read the "Notice for TAIYO YUDEN products" before using this catalog.

5 PART NUMBERS LB328 TYPE L B 328 T R 0 M L B 328 T R M L B 328 T 2 R 2 M L B 328 T 3 R 3 M L B 328 T 4 R 7 M L B 328 T 6 R 8 M L B 328 T 0 0 L B 328 T 0 L B 328 T L B 328 T L B 328 T L B 328 T L B 328 T 0 L B 328 T L B 328 T 2 2 L B 328 T 3 3 L B 328 T 4 7 L B 328 T 6 8 L B 328 T 0 2 (Environmental Substances) H % % 20% MHz min (30% Rated current ma max MHz LBMF608 TYPE L B M F T R 0 M L B M F T 2 R 2 M L B M F T 3 R 3 M L B M F T 4 R 7 M L B M F T 0 0 L B M F T L B M F T (Environmental Substances) H % % 20% MHz min % Rated current ma max MHz 7.96 LBC28 TYPE L B C 2 8 T R 0 M L B C 2 8 T R 0 M R L B C 2 8 T R M L B C 2 8 T 2 R 2 M L B C 2 8 T 3 R 3 M L B C 2 8 T 4 R 7 M L B C 2 8 T 6 R 8 M L B C 2 8 T 0 0 L B C 2 8 T 0 L B C 2 8 T L B C 2 8 T L B C 2 8 T L B C 2 8 T L B C 2 8 T 0 L B C 2 8 T L B C 2 8 T 2 2 L B C 2 8 T 3 3 L B C 2 8 T 4 7 L B C 2 8 T 6 8 (Environmental Substances) H % % 20% MHz min (30% Rated current ma max MHz Pleasespecifythetolerancecode K or M Please read the "Notice for TAIYO YUDEN products" before using this catalog.

6 PART NUMBERS LBC206 TYPE L B C T R 0 M L B C T R M L B C T 2 R 2 M L B C T 3 R 3 M L B C T 4 R 7 M L B C T 6 R 8 M L B C T 0 0 L B C T 0 L B C T L B C T L B C T L B C T L B C T 0 Environmental Substances H MHz min % Rated current ma max MHz LBC202 TYPE L B C T R 0 M L B C T 2 R 2 M L B C T 4 R 7 M L B C T 0 0 L B C T L B C T Environmental Substances H MHz min % Rated current ma max MHz 7.96 LBR28 TYPE L B R 2 8 T R 0 M L B R 2 8 T 2 R 2 M L B R 2 8 T 4 R 7 M L B R 2 8 T 0 0 L B R 2 8 T L B R 2 8 T L B R 2 8 T 0 Environmental Substances H MHz min % Rated current ma max MHz LBR202 TYPE L B R T R 0 M L B R T 2 R 2 M L B R T 4 R 7 M L B R T 0 0 L B R T L B R T L B R T 0 Environmental Substances H MHz min % Rated current ma max MHz Pleasespecifythetolerancecode K or M 6 Please read the "Notice for TAIYO YUDEN products" before using this catalog.

7 ELECTRICAL CHARACTERISTICS Bias characteristics Measured by HP428A4284A Standard LB608 LB202 LB H M R0M H R0M H R0M 0. 0 Bias ma Bias ma Bias ma LB28 LB H R0M H R0M Bias ma Bias ma High Current LBC202 LBC206 LBC H R0M H R0M H R0M 0. 0 Bias ma Bias ma Bias ma Low Rdc Bottom-surface electrode LBR202 LBR28 LBMF H H R0M H 4R7M R0M R0M 0 Bias ma Bias ma 0. 0 Bias ma 8 Please read the "Notice for TAIYO YUDEN products" before using this catalog.

8 ELECTRICAL CHARACTERISTICS Impedance-vs-Frequency characteristics Measured by HP429A Standard LB608 LB202 LB M Impedance Frequency MHz LB28 R0M Impedance R0M 0 00 Frequency MHz LB328 Impedance 00 0 R0M 0 00 Frequency MHz Impedance 00 0 R0M Impedance 00 0 R0M 0 00 Frequency MHz 0 00 Frequency MHz High Current LBC202 LBC206 LBC Impedance 0 0 R0M Impedance 0 R0M Impedance 0 R0M 0 00 Frequency MHz 0 00 Frequency MHz 0 00 Frequency MHz Low Rdc Bottom-surface electrode LBR202 LBR28 LBMF Impedance 0 R0M Impedance 0 R0M Impedance 0 4R7M 0 00 Frequency MHz 0 00 Frequency MHz 0 00 Frequency MHz Please read the "Notice for TAIYO YUDEN products" before using this catalog. 9

9 WOUND CHIP POWER INDUCTORS SERIES OPERATING TEMP. 2 Including self-generated heat FEATURES LB / LBC / MF 608 / This series correspond to high electric current compared with LB/LBC series. Wound Chip Inductors that can be used for small / converters and are suit for choke uses. MF608 Series The best efficiency design is achieved by adopting bottom-surface electrode structure. Wound Chip Inductors that are suit for module design which needs high electric current like / converters. APPLICATIONS DSC / DVC / HDD DSC/DVC/HDD, LCD, portable telephones, game equipments. Various audio-visual equipments, various communication equipments, etc. ORDERING CODE 2 C L MF C Rdc 3 mm T B T H R0 R 6 K M 20 7 R Rdc 8 2 Wound chip power inductor Characteristic Spec Low Rdc C High current L Low profile MF Bottom-surface electrode 3 External Dimensions mm Packaging T Tape & Reel Nominal H example R0 *R=decimal point 6 s % K M 20 7 Special code R Standard products Low Rdc type 8 Internal code Standard Products Blank space 60 Please read the "Notice for TAIYO YUDEN products" before using this catalog.

10 EXTERNAL DIMENSIONS L W T e Recommended Land Patterns C3 28 C C C202 L202 MF Unit mminch Surface Mounting Mounting and soldering conditions should be checked beforehand. Applicable soldering process to this products is reflow soldering only. Recommended Land Patterns AVAILABLE INDUCTANCE RANGE Range C3 C28 C206 C202 L202 MF608 ImaxmA Rdc30 ImaxmA Rdc30 ImaxmA Rdc30 ImaxmA Rdc30 ImaxmA Rdc30 ImaxmA Rdc30 ImaxmA Rdc30 ImaxmA Rdc30 ImaxmA Rdc H H H H H 0.08 H H H H H H 4.2 H 0 2. H H H H H H H Examples Imax Rdc30% ma Imax ma Rdc30% Imax ma Rdc30% H H H H H Imax Rdc30% Imax Rdc30% Imax ma ma ma Rdc30% Imax Rdc30% Imax Rdc30% Imax ma ma ma Rdc30% Selection Guide Part Numbers Electrical Characteristics Packaging Reliability Data Precautions P.4 P.62 P.66 P.73 P.74 P.84 etc Please read the "Notice for TAIYO YUDEN products" before using this catalog. 6

11 PART NUMBERS 202 TYPE C B T R 0 M C B T 2 R 2 M C B T 3 R 3 M C B T 4 R 7 M C B T 6 R 8 M C B T 00 C B T 00 R C B T 0 C B T 2 20 C B T 4 70 C B T T 0 Environmental Substances H % % 20% MHz min Saturation current Idc ma Temperature rise current Idc MHz TYPE T R 0 M T R M T 2 R 2 M T 3 R 3 M T 4 R 7 M T 6 R 8 M T T T T T T T 0 Environmental Substances H % % 20% MHz min Saturation current Idc ma Temperature rise current Idc MHz TYPE 2 8 T R 0 M 2 8 T R M 2 8 T 2 R 2 M 2 8 T 3 R 3 M 2 8 T 4 R 7 M R 2 8 T 4 R 7 M 2 8 T 6 R 8 M 2 8 T T T T T T T T 2 8 T T T T T 02 Environmental Substances H Pleasespecifythetolerancecodeor 20% % 20% MHz min Saturation current Idc Idc30% at 20 The saturation current valueidcis the current value having inductance decrease down to 30%. at 20 Idc240 at 20 The temperature rise current valueidc2is the current value having temperature increase up to 40. at ma Temperature rise current Idc2 The maximum rated current is the current value that satisfies both of saturation current value and temperature rise current value MHz Please read the "Notice for TAIYO YUDEN products" before using this catalog.

12 PART NUMBERS C202 TYPE C B C T R 0 M C B C T 2 R 2 M C B C T 4 R 7 M C B C T 0 0 C B C T C B C T C206 TYPE C T R 0 M C T R M C T 2 R 2 M C T 3 R 3 M C T 4 R 7 M C T 6 R 8 M C T 0 0 C T 0 C T C T C T C T C T 0 C28 TYPE C 2 8 T R 0 M C 2 8 T R M C 2 8 T 2 R 2 M C 2 8 T 3 R 3 M C 2 8 T 4 R 7 M C 2 8 T 6 R 8 M C 2 8 T 0 0 C 2 8 T 0 C 2 8 T C 2 8 T C 2 8 T C 2 8 T C 2 8 T 0 C 2 8 T C 2 8 T 2 2 C 2 8 T 3 3 C 2 8 T 4 7 C 2 8 T 6 8 Environmental Substances Environmental Substances Environmental Substances H.0 H H Pleasespecifythetolerancecodeor 20% % 20% 20% % 20% 20% % 20% MHz min MHz min MHz min Saturation current Idc Saturation current Idc Saturation current Idc Idc30% at 20 The saturation current valueidcis the current value having inductance decrease down to 30%. at 20 Idc240 at 20 The temperature rise current valueidc2is the current value having temperature increase up to 40. at ma Temperature rise current Idc2 ma Temperature rise current Idc2 ma Temperature rise current Idc2 The maximum rated current is the current value that satisfies both of saturation current value and temperature rise current value MHz 7.96 MHz MHz Please read the "Notice for TAIYO YUDEN products" before using this catalog. 63

13 PART NUMBERS C3 TYPE C B C3 T R 0 MR C3 T R M R C3 T 2 R 2 M R C3 T 3 R 3 M R C3 T 4 R 7 M R C3 T 6 R 8 M R C3 T 00 R C3 T 0 R C3 T 2 20 R C3 T 3 30 R C3 T 4 70 R C3 T 6 80 R C3 T 0 R Environmental Substances H % % 20% MHz min ma Saturation current Temperature rise current Idc Idc MHz 0. L202 TYPE C B L T R 0 M C B L T 2 R 2 M C B L T 4 R 7 M C B L T 0 0 M C B L T M C B L T M Environmental Substances H.0 20% MHz min ma Saturation current Temperature rise current Idc Idc MHz 0. MF608 TYPE C B M F T R 0 M C B M F T 2 R 2 M C B M F T 3 R 3M C B M F T 4 R 7 M C B M F T 0 0 C B M F T C B M F T Environmental Substances H % % 20% MHz min Saturation current Idc ma Temperature rise current Idc MHz 7.96 Pleasespecifythetolerancecodeor Idc30% at 20 The saturation current valueidcis the current value having inductance decrease down to 30%. at 20 Idc240 at 20 The temperature rise current valueidc2is the current value having temperature increase up to 40. at 20 The maximum rated current is the current value that satisfies both of saturation current value and temperature rise current value. 64 Please read the "Notice for TAIYO YUDEN products" before using this catalog.

14 ELECTRICAL CHARACTERISTICS Bias characteristics Measured by HP428A4284A Low Rdc H R0M H R0M H R0M Bias ma Bias ma Bias ma High Current C202 C206 C H R0M H R0M H R0M 0. 0 Bias ma Bias ma Bias ma C3 R H R R0MR Bias ma Low Profile Bottom-surface electrode L202 MF608 0M 4R7M H M H R0M 4R7M 0 Bias ma 0 Bias ma 66 Please read the "Notice for TAIYO YUDEN products" before using this catalog.

15 ELECTRICAL CHARACTERISTICS Impedance-vs-Frequency characteristicsmeasured by HP429A Low Rdc Impedance 0 Frequency MHz High Current R0M 0 00 Impedance 0 R0M 0 00 Frequency MHz Impedance 0 R0M 0 00 Frequency MHz C202 C206 C Impedance 0 R0M Impedance 0 R0M Impedance 0 R0M 0 00 Frequency MHz 0 00 Frequency MHz 0 00 Frequency MHz C3 R R R0MR Impedance Frequency MHz Low Profile Bottom-surface electrode L202 MF M M 4R7M 00 0 Impedance 0 Impedance 0 4R7M 0 Frequency MHz 0 00 Frequency MHz Please read the "Notice for TAIYO YUDEN products" before using this catalog. 67

16 WOUND CHIP INDUCTORS FOR SIGNAL LINE LB SERIES M TYPE LE SERIES M TYPE OPERATING TEMP. LBM206 TYPE LEM0 TYPE 2 Including self-generated heat 408 FEATURES LBM206 Q LEM0 LBM206 Series High Q and narrow tolerance are achieved by adopting bottom-surface electrode structure.wound Chip Inductors that are suit for module design of signal line uses. LEM0 Series A high-quality inductor that is simple to mass-produce and conforms to the same production process and basic construction as an axial lead type inductor. APPLICATIONS DSC / DVC / HDD DSC/DVC/HDD, LCD, portable telephones, game equipments. Various audio-visual equipments, various communication equipments, etc. ORDERING CODE LBM LEM 3 T 4 H R2 0.2 R J K 2 mm L B M T J 4 6 LBM LEM Wound chip inductor for signal line Wound chip inductor for signal line 3 Packaging T Tape & Reel 4 Nominal H example R2 0.2 R s J K 2 External Dimensions mm Internal code Standard Products Blank space 68 Please read the "Notice for TAIYO YUDEN products" before using this catalog.

17 EXTERNAL DIMENSIONS LBM206 LEM0 e e L W T e w LBM LEM Unitmminch Recommended Land Patterns LB Surface Mounting Mounting and soldering conditions should be checked beforehand. Applicable soldering process to this products is reflow soldering only. LB only Recommended Land Patterns Unit mm C A B A AVAILABLE INDUCTANCE RANGE Range 0.2 LBM206 Idc[mA] Rdc30[] LEM0 Idc[mA] Rdc max Ordinary type H H H Examples IdcmA Rdc LBM206 LEM0 LBM206 LEM0 max. max. 30 max. 0.2H H H H Selection Guide Part Numbers Electrical Characteristics Packaging Reliability Data Precautions P.4 P.70 P.72 P.73 P.74 P.84 etc Please read the "Notice for TAIYO YUDEN products" before using this catalog. 69

18 PART NUMBERS LBM206 TYPE LB M206TR2J LB M206TRJ LB M206TR8J LB M206TRJ LB M206TR27J LB M206TR33J LB M206TR39J LB M206TRJ LB M206TR6J LB M206TR68J LB M206TR82J LB M206TR0J LB M206TR2J LB M206TRJ LB M206TR8J LB M206T2R2J LB M206T2R7J LB M206 T 3 R 3 J LB M206T3R9J LB M206T4R7J LB M206TR6J LB M206T6R8J LB M206T8R2J LB M206TJ LB M206T20J LB M206T0J LB M206T80J LB M206T0J LB M206T270J LB M206T330J LB M206T390J LB M206T0J LB M206T60J LB M206T680J LB M206T820J LB M206TJ Environmental Substances H Q Q VALUE min MHz min Rated current ma max MHz Please read the "Notice for TAIYO YUDEN products" before using this catalog.

19 PART NUMBERS LEM0 TYPE L E M T R 2 K L E M T R K L E M T R 8 K L E M T R 2 2 K L E M T R 2 7 K L E M T R 3 3 K L E M T R 3 9 K L E M T R 4 7 K L E M T R 6 K L E M T R 6 8 K L E M T R 8 2 K L E M T R 0 J L E M T R 2 J L E M T R J L E M T R 8 J L E M T 2 R 2 J L E M T 2 R 7 J L E M T 3 R 3 J L E M T 3 R 9 J L E M T 4 R 7 J L E M T R 6 J L E M T 6 R 8 J L E M T 8 R 2 J L E M T 0 0 J L E M T 2 0 J L E M T 0 J L E M T 8 0 J L E M T J L E M T J L E M T J L E M T J L E M T J L E M T 6 0 J L E M T J L E M T J L E M T 0 J (Environmental Substances) H Q min. MHz min. max. ma max MHz Please read the "Notice for TAIYO YUDEN products" before using this catalog. 7

20 ELECTRICAL CHARACTERISTICS LBM206 Q- Q-Characteristics Impedance-vs-Frequency characteristics J R0J J J J 00 R0J Q 0 0 Frequency[MHz] Freaquency[MHz] -vs-frequency characteristics 0 [H] J J R0J 0 Freaquency[MHz] LEM0 Q-Q-Characteristics Ordinary typemeasured by HP428A428A Bias characteristicsmeasured by HP428A4284A Temperature characteristicsmeasured by HP428A428A 72 Please read the "Notice for TAIYO YUDEN products" before using this catalog.

21 PACKAGING Minimum Quantity Standard Quantity pcs Papar Tape Embossed Tape C3 0 LB LBR28/LBC28/LB28 /28/C28/LEM LBM206/LBC206/LB206 /206/C LB202/LBC202/LBR202 /202/C L LB LBMF608/MF Tape material Chip cavity Insertion pitch Tape thickness A B F T K LBM LEM C max 4.0max LB max LB28 / LBC28 / C LBR28 LB206/ LBC206 / C LB202 / LBC202 / C LBR202 L max.max LB max.max LBMF608 / MF max.6max Leader and Blank Portion Reel Size 2.max Taping Dimensions 8mmEmbossed Tape 0.3 inches wide 8mmCard board carrier tape 0.3 inches wide ) ).0. ( ) Top Tape Strength 0.0.7N The top tape requires a peel-off force 0. to 0.7N in the direction of the arrow as illustrated below. Please read the "Notice for TAIYO YUDEN products" before using this catalog. 73

22 RELIABILITY DATA / Specified Value Item LEM0 LB328 LB28 LB206 LB202 LB608 LBMF608 LBC28 LBC206 LBC202 LBR28 LBR C3 C28 C206 C202 L202 MF608 LBM206 Test Methods and Remarks.Operating tem Including self-generated heat perature Range 2.Storage Rated Current Within the specified tolerance LEMLBLBCLBMFLBM Series The maximum value having inductance decrease within and temperature increase within 20 by the application of bias. LBR Series The maximum value having inductance decrease within 20 and temperature increase within 20 by the application of bias. CLMF Series The maximum value having inductance decrease within 30 and temperature increase within 40 by the application of bias. 4. Within the specified tolerance LEM Series R2 equipmentlcr Meter HP428A428A or its equivalent Specified LBLBC LBR CLLBMF MFLBM Series equipmentlcr Mater HP428A or its equivalent.q Within the Within the LEM Series R2 specified specified equipmentlcr Meter tolerance tolerance HP428A428A or its equivalent Specified LBM Series equipmentlcr Mater HP428A or its equivalent 6. Resisitance Within the specified tolerance LEMLBLBCLBRCLLBM LBMFMF Series equipment Ohmmeter HIOKI 37 or its equivalent 7.Self-Resonant Within the specified tolerance LEM0 Frequency equipmentimpedance analyzer HP429A or its equivalent LBLBCLBRCLLBMF MF Series equipment Impedance analyzer HP429A or its equivalent LBM Series equipmentnetwork analyzer HP8720B or its equivalent Please read the "Notice for TAIYO YUDEN products" before using this catalog. 7

23 RELIABILITY DATA 2/ Specified Value Item 8.Temperature Characteristic LEM0 change: Within LB328 LB28 LB206 LB202 LB608 LBMF608 LBC28 LBC206 LBC202 change: LBC28 Within LBC206 LBR28 LBR202 change: C3 28 C C C202 change: C3 Within Within C28 L202 change: MF608 change: LBM206 change: Within Within20 Within Test Methods and Remarks Change of maximum inductance deviation in step change: C206 9.Rasistance to Flexure of Substrate No damage. LBMF608 LB328 Within20 change: LBC202 Within20 change: Within30 change: Within20 C202 change: Within30 Step Temperture Reference temperature 4 8Maximum operating temperature 20 Warp: 2mm LB, LBC, LBR,, C, L, LBM,LBMF, MF Series Warp: 3mm LEM0 Test substrate: Printed board According to JIS C00 Pressig jig LBLBMF MF mm Others.0mm Board.Body Strength. S e l f R e s o n a n t Freguency 2.Adhesion of terminal electrode 3. R e s i s t a n c e t o vibration No damage. change : Within No abnormality. change: change : Within Within No significant abnormality in appearance. No significant abnormality in appearance. change: change : Within30 Within20 LBLBCLBRCLLBMLEM0 Applied forcen Durationsec. LB608LBMF608MF608 Applied forcen Durationsec. change: Measure inductance with application of rated Within current using LCR metre to cpmpare it with the initial value. LBLBCLBRCLLBMLBMF MFLEM0 Applied forcen to X and Y directions Duration sec. Test substrateprinted board change: LEMLBLBCLBRCL Within LBMLBMFMF No significant abnor- Vibration type According to JIS C2 clause 8.2. mality in Directions 2 hrs each in X, Y and Z directions. Total6 hrs appearance. Frequency range to to Hz min. Amplitude.mm Mounting methodsoldering onto printed board Recovery At least 2 hrs of recovery under the standard condition after the test, followed by the measurement within 48 hrs. Please read the "Notice for TAIYO YUDEN products" before using this catalog. 77

24 RELIABILITY DATA 3/ Specified Value Item LEM0 LB328 LB28 LB206 LB202 LB608 LBMF608 LBC28 LBC206 LBC202 LBR28 LBR C3 C28 C206 C202 L202 MF608 LBM206 Test Methods and Remarks 4.Drop test change : LEM Within Acceleration980m/sec 2 No significant Duration6msec abnormality Number of times6 sides 3 times in appearance. Mounting methodsoldering onto printed board Recovery At least 2 hrs of recovery under the standard condition.solderability At least 90 of surface of terminal electrode is covered by new solder. after the test, followed by the measurement within 48 hrs. LEM Solder temperature230 Duration0.sec. Flux Methanol solution with 2 of colophony LBLBCLBRCLLBM LBMFMF Solder temperature24 Duration0.sec Flux Methanol solution with 2 of colophony 6.Resisitance to soldering heat change : LB328 LB28 Within LB206 No significant LB202 abnormality in LB608 change : appearance. Within No significant change : within No significant abnormality in appearance. change : Within20 No significant abnormality in appearance. change : LEM Within Reflow condition 3 times of reflow over No significant at 0 for 40sec. MAX, With Peak abnormality temperature at 240 for sec. MAX. in appearance. Refer to a Profile of chart below. abnormality in appearance. LBMF608 change : Within20 No significant abnormality in appearance. Flow condition Solder temperature260 Durationsec. Once LBLBCLBRCLLBM LBMFMF 3 times of reflow oven at 230 MIN for 40sec. with peak temperature 0 at 260 for sec. 7.Resisitance to Solvent temperatureroom temperature solvent No significant abnormality in appearance of solventisopropyl alcohol LEM0LBLBCLBR CLLBM LBMFMF Cleaning conditions90s. Immersion and cleaning. LEM0LBLBC LBRC LLBMLBMF MF Please read the "Notice for TAIYO YUDEN products" before using this catalog. 79

25 RELIABILITY DATA 4/ Specified Value Item 8.Thermal shock LEM0 change : LB328 LB28 LB206 LB202 LB608 LBMF608 LBC28 LBC206 LBC202 LBR28 LBR202 change :Within C3 C28 C206 C202 L202 MF608 LBM206 Test Methods and Remarks LEM : Conditions for cycle Within No significant abnormality in appearance. Step Temperature Durationmin Q R24R min. R6330 2min. Number of cycle cycle Recovery At least hr of recovery the standard condition after the removal min. min. from test chamber, followed by measurement within 2 hrs. LBLBCLBRCLLBM LBMFMF 408, maintain times 30min., cycle Recovery At least 2 hrs of recovery under the standard condition after the test, followed by the measurement within 48 hrs. 9.Damp heat change : change :Within Temperature602 Within No significant abnormality in appearance. Humidity909RH Q Duration0 hrs R24R7 Recovery At least 2 hrs of recovery under 30min. the standard condition after the R6330 test, followed by the measure- 2min. ment within 48 hrs min. min. 20.Loading under change : change : Within LEMLBLBCCLLBM damp heat Within No significant abnormality in appearance. LBMFMF Q Temperature602 R24R7 Humidity909RH 30min. Duration0 hrs R6330 Applied current 2min. Recovery At least 2 hrs of recovery under the standard condition after the 20min. test, followed by the measure- min. ment within 48 hrs. 2.High temperature change : change :Within LEMCLLBMMF life test Within No significant abnormality in appearance. Temperature82 Q Duration0 hrs R24R7 Recovery At least 2 hrs of recovery under 30min. the standard condition after R6330 the test, followed by the mea- 2min. surement within 48 hrs min. min..loading at high temperature change :Within No significant abnormality in appearance. LBLBCLBRLBMF Temperature82 Duration0 hrs Applied current Recovery At least 2 hrs of recovery under the standard condition after the test, followed by the measurement within 48 hrs. Please read the "Notice for TAIYO YUDEN products" before using this catalog. 8

26 RELIABILITY DATA / Specified Value Item 23.Low temperature life test 24.Standard condition LEM0 LB328 LB28 LB206 LB202 LB608 LBMF608 LBC28 LBC206 LBC202 LBR28 LBR202 change : change :Within Within No significant abnormality in appearance. Q R24R7 30min. R6330 2min min. min C3 C28 C206 C202 L202 MF608 LBM206 Standard test conditionunless otherwise specified,temperature is 20, and 620 of relative humidity.when there are question concerning measurement result In order to provide correlation date, the test shall be condition of 202 of temperature, 6 relative humidity. is in accordance with our measured value. Test Methods and Remarks LEMLBLBCLBRCLLBM LBMFMF Temperature402 Duration0 hrs Recovery At least 2 hrs of recovery under the standard condition after the test, followed by the measurement within 48 hrs. Please read the "Notice for TAIYO YUDEN products" before using this catalog. 83

27 PRECAUTIONS LEM LB Stages Precautions Technical considerations.circuit Design Operating environment,.the products described in this specification are intended for use in general electronic equipment,(office supply equipment, telecommunications systems, measuring equipment, and household equipment). They are not intended for use in mission-critical equipment or systems requiring special quality and high reliability (traffic systems, safety equipment, aerospace systems, nuclear control 2.P Design systems and medical equipment including life-support systems,) where product failure might result in loss of life, injury or damage. For such uses, contact TAIYO YUDEN Sales Department in advance. Land pattern design.please contact any of our offices for a land pattern, and refer to a recommended land pattern of a right figure or specifications. PRECAUTIONS Recommended Land Patterns Surface Mounting Mounting and soldering conditions should be checked beforehand. Applicable soldering process to this products is reflow soldering only. Recommended Land Patterns C Unit : mm TYPE A B C MF LEM A B A Considerations for Adjustment of mounting machine automatic placement.excessive impact load should not be imposed on the. When installing products, care should be taken not to apply distortion stress as it products when mounting onto the PC boards. may deform the products. 2.Mounting and soldering conditions should be checked beforehand. 4.Soldering Wave soldering (LEM only).for wave soldering,please apply conditions meeting the.components can be damaged by excessive heat whre soldering conditions exceed range of the specifed conditions in our catalog or the the specified range. relevant specifications. Reflow soldering (LB and s).for reflow soldering with either leaded or lead-free.reflow profile solder,the profile specified in "point for controlling" is recommended. Reflow soldering (LEM).For reflow soldering, please apply conditions meeting the range of the specified conditions in our catalog or the relevant specifications Pre-heat zone 9030 sec 30 sec Peak Temp: 20 sec Max 230 Minn 0.Cleaning 6.Handling 7.Storage conditions Recommended conditions for using a soldering iron.put the soldering iron on the land-pattern. Soldering iron's temperature-below 30 Duration-3 secons or less The soldering iron shoud not come in contact with inductor directly. Cleaning conditions LEM, LB,.Washing by supersonic waves shall be avoided. Handling.Keep the inductors away from all magnets and magnetic objects. Breakaway PC boards (splitting along perforations).when splitting the PC board after mounting inductors, care should be taken not to give any stresses of deflection or twisting to the board. 2.Board separation should not be done manually, but by using the appropriate devices. Mechanical considerations.please do not give the inductors any excessive mechanical shocks. Storage.To maintain the solderability of terminal electrodes and to keep the packing material in good condition, temperature and humidity in the storage area should be controlled. Recommended conditions Ambient temperature 040 Humidity Below 70% RH The ambient temperature must be kept below 30 Even under ideal storage conditions, solderability of products electrodes may decrease as time passes. For this reason, LE type inductors should be used within one year from the time of delivery. LB type Please should be used within 6 months from the time of delivery. LE type In case of storage over 6 months, solderability shall be checked before actual usage. 0.Components can be damaged by excessive heat whre soldering conditions exceed the specified range. LEM, LB,.If washing by supersonic waves, supersonic waves may cause broken products..there is a case that a characteristic varies with magnetic influence..planning pattern configurations and the position of products should be carefully performed to minimize stress..there is a case to be damaged by a mechanical shock.. Under a high temperature and humidity environment, problems suchas reduced solderability caused by oxidation of terminal electrodes and deterioration of taping/packaging materials may take place. Please read the "Notice for TAIYO YUDEN products" before using this catalog. 8

28 SMD INDUCTORS LOW PROFILE TYPE OPERATING TEMP 0 Inducting self-generated heat FEATURES Small and Low profile inductor. It corresponds to High current. Simple and original magnetic shield structure. Structure strong against a shock-proof. APPLICATIONS HDDDVCDSCPDA/ For small / converter cellular Phone, HDD,DVC, DSC, PDA, LCD display etc. ORDERING CODE 2 WLH NR, NRG mm mm mm mm mm mm mm mm mm mm mm mm 3 T 2R H M 20 N 30 6 N R T 0 0 M NR, NRG Coating resin specification Blank Space 2 External dimensionswlh example mm mm mm mm mm mm mm mm mm mm mm mm 3 Packaging T example 2R Tape and Reel Blank Space 4 Nominal inductanceh tolerance M 20 N 30 6 Internal code 6 Standard product Blank Space 342 Please read the "Notice for TAIYO YUDEN products" before using this catalog.

29 f EXTERNAL DIMENSIONS L H L H 2.3 e e W f W e Δe e NR 30.0 max (0.039 max) NR 302 NR 30 NR 40 NR 402 NR 408 NRG4026 NR ( ) ( ) ( ) ( ) ( ) ( ).2 max (0.0 max). max (0.09 max).0 max (0.039 max).2 max (0.0 max).8 max (0.07 max) 2.6 max (0.2 max) *4.2max (0.6max) *24.0max (0.7max) ( ).0.2 ( ).60.3 ( ).90.2 ( ).0.2 ( ).60.3 ( ) *0R96R8 *2 Unit mminch NR max E max max NR max max NR (0. max) max NR max Unit mminch Recommended Land Patterns AVAILABLE INDUCTANCE RANGE Range NR30 NR302 NR30 NR40 NR402 NR408 NR602 NR6020 NR6028 NR604 NR8040 NRG4026 ImaxmA Rdc20ImaxmA Rdc20ImaxmA Rdc20ImaxmA Rdc20ImaxmA Rdc20ImaxmA Rdc20ImaxmA Rdc20ImaxmA Rdc30ImaxmA Rdc30ImaxmA Rdc30ImaxmA Rdc30ImaxmA Rdc H Selection Guide Part Numbers Electrical Characteristics Packaging Reliability Data Precautions P.4 P.344 P.348 P.33 P.366 P.374 etc Please read the "Notice for TAIYO YUDEN products" before using this catalog. 343

30 PART NUMBERS NR 30 Shielded type [H] ma Saturation current Idc Temperature rise current Idc2 khz NR T R 0 N NR T R N NR T 2 R 2 M NR T 3 R 3 M NR T 4 R 7 M NR T 6 R 8 M NR T 0 0 M NR T 0 M NR T M NR T M NR T M Environmental Substances % 20% MHz min ,300,200, ,400,300, NR 302 Shielded type Environmental Substances ma Saturation current Idc Temperature rise current Idc2 khz NR T R 0 N NR T R N NR T 2 R 2 M NR T 3 R 3 M NR T 4 R 7 M NR T 6 R 8 M NR T 0 0 M NR T 0 M NR T M NR T M NR T M [H] % 20% MHz min ,00,360, ,490,400,200, NR 30 Shielded type NR 3 0 T R 0 N NR 3 0 T R N NR 3 0 T 2 R 2 M NR 3 0 T 3 R 3 M NR 3 0 T 4 R 7 M NR 3 0 T 6 R 8 M NR 3 0 T 0 0 M NR 3 0 T 0 M NR 3 0 T M NR 3 0 T M NR 3 0 T M Environmental Substances [H] % 20% MHz min ,,800,480,2, ma Saturation current Idc Temperature rise current Idc2 2,,820,00,230, khz Idc) 30% at 20 ) The saturation current valueidc) is the current value having inductance decrease down to 30%. at 20 ) Idc2) 40 at 20 ) The temperature rise current valueidc2) is the current value having temperature increase up to 40. at 20 ) The rated current is the current value that satisfies both of current value saturation current value and temperature rise current value. 344 Please read the "Notice for TAIYO YUDEN products" before using this catalog.

31 PART NUMBERS NR 40 Shielded type NR T R 0 N NR T 2 R 2 N NR T 3 R 3 M NR T 4 R 7 M NR T 6 R 8 M NR T 0 0 M NR T 0 M NR T M NR T M NR T M NR 402 Shielded type NR T R 0 N NR T 2 R 2 M NR T 3 R 3 M NR T 4 R 7 M NR T 6 R 8 M NR T 0 0 M NR T 0 M NR T M NR T M NR T M Environmental Substances Environmental Substances [H] H % 20% 30% 20% MHz min MHz min ,800,0, ,00,60,200, ma Saturation current Idc ma Saturation current Idc Temperature rise current Idc2, Temperature rise current Idc2,00, khz khz NR 408 Shielded type NR T R 0 N NR T 2 R 2 M NR T 3 R 3 M NR T 4 R 7 M NR T 6 R 8 M NR T 0 0 M NR T 0 M NR T M NR T M NR T M NR T M NR T 0 M NR T M NR T 2 2 M Environmental Substances H % 20% MHz min ,000 2,700 2,000,700,40, ma Saturation current Idc Temperature rise current Idc2,830,440,230,200, khz Idc) 30% at 20 ) The saturation current valueidc) is the current value having inductance decrease down to 30%. at 20 ) Idc2) 40 at 20 ) The temperature rise current valueidc2) is the current value having temperature increase up to 40. at 20 ) The rated current is the current value that satisfies both of current value saturation current value and temperature rise current value. Please read the "Notice for TAIYO YUDEN products" before using this catalog. 34

32 PART NUMBERS NR 602 Shielded type NR T 2 R NE NR T 4 R 0 NE NR T R 3 ME NR T 6 R 8 ME NR T 0 0 ME NR T 0 ME NR T ME NR T ME NR T ME NR T ME NR T 0 ME Environmental Substances H % 20% MHz min ,,800,00,300, ma Saturation current Idc Temperature rise current Idc2,730,70,400,80, khz NR 6020 Shielded type Environmental Substances H MHz min 30% ma Saturation current Idc Temperature rise current Idc2 NR 6020T 0R8N ,00 3,800 NR 6020T RN ,000 3,200 NR 6020T 2R2N ,200 2,700 30% NR 6020T 3R3N ,800 2,600 NR 6020T 4R7N ,400 2,000 NR 6020T 6R8N ,000,800 NR 6020T M 8 0.2,700,400 20% NR 6020T 0M 0.290,00 90 khz NR 6028 Shielded type NR 6028T 0R9N NR 6028T RN NR 6028T 2R2N NR 6028T 3R0N NR 6028T 4R7M NR 6028T 6R0M NR 6028T M NR 6028T 0M NR 6028T 0M NR 6028T 330M NR 6028T 0M NR 6028T 680M NR 6028T M Environmental Substances H % 20% MHz min ,600,000 4,200 3,600 2,700 2,00,900,600,300, ma Saturation current (L/L-30%) Temperature rise current (T40) 4,600 4,200 3,700 3,400 3,000 2,00,900,800,400, khz Idc) 30% at 20 ) The saturation current valueidc) is the current value having inductance decrease down to 30%. at 20 ) Idc2) 40 at 20 ) The temperature rise current valueidc2) is the current value having temperature increase up to 40. at 20 ) The rated current is the current value that satisfies both of current value saturation current value and temperature rise current value. 346 Please read the "Notice for TAIYO YUDEN products" before using this catalog.

WOUND CHIP POWER INDUCTORS SERIES OPERATING TEMP. 2 Including self-generated heat FEATURES LB / LBC / MF 608 / This series correspond to high electric

WOUND CHIP POWER INDUCTORS SERIES OPERATING TEMP. 2 Including self-generated heat FEATURES LB / LBC / MF 608 / This series correspond to high electric Notice for TAIYO YUDEN products Please read this notice before using the TAIYO YUDEN products. REMINDERS Product information in this catalog is as of October 2008. All of the contents specified herein

More information

WOUND CHIP INDUCTORS LB SERIES OPERATING TEMP. 2 Including self-generated heat FEATURES Rdc LB/LBRRdcIdc LBCIdcRdc LB83 3 LBMF Wound Chip Induc

WOUND CHIP INDUCTORS LB SERIES OPERATING TEMP. 2 Including self-generated heat FEATURES Rdc LB/LBRRdcIdc LBCIdcRdc LB83 3 LBMF Wound Chip Induc Notice for TAIYO YUDEN products Please read this notice before using the TAIYO YUDEN products. REMINDERS Product information in this catalog is as of October 2008. All of the contents specified herein

More information

cms.pdf

cms.pdf RoHS compliant INTERNAL STRUTURE FEATURES Part name over Slider Housing Slider contact Fixed contact Terminal pin lick spring Ground terminal Material Steel (SP), Tin-plated Polyamide opper alloy, Gold-plated

More information

Ł\”ƒ_−mflF

Ł\”ƒ_−mflF COAXIAL CONNECTORS CAT.NO.COAX-007H.JAN.2018 Adapter for pin/socket conversion of the same series or connection between connectors of different series. Applicable to various series. A wide variety of types

More information

Description

Description Metal Hybrid Inductor Description Metal Hybrid Inductor Magnetically shielded Suitable for Large Current Size: 4.3 x 4.3 x H2.1 mm Max. Product weight:.18g (Ref.) Halogen Free available Operating temperature

More information

Microsoft Word - CDEIR10D50ME_Ver1.0_E.docx

Microsoft Word - CDEIR10D50ME_Ver1.0_E.docx CDEIR1D5ME Description Metal alloy core construction Magnetically shielded L W H: 11.5 1.7 5.mm Max. Product weight :.7 g (Ref.) Moisture Sensitivity Level: 1 Applications Ideally used in Notebook, PDA

More information

PowerPoint プレゼンテーション

PowerPoint プレゼンテーション 一般機器用 For Consumer Products 汎用パワーインダクタ Common Power Inductors HER series RoHS HER327 HER427 HER527 HER627 HER88 HER9 特徴 直流重畳特性に優れている為 DC-DC コンバータ用インダクタとして最適 ドラムコアとリングコアに異なる磁性材料を使い電流特性を向上 * 既存同サイズと比べて電流特性を約

More information

MULTILAYER CHIP INDUCTORS LK SERIES OPERATING TEMP. 40 LK Except for LK FEATURES HLK Internal printed coil structure creates a closed magnetic circuit

MULTILAYER CHIP INDUCTORS LK SERIES OPERATING TEMP. 40 LK Except for LK FEATURES HLK Internal printed coil structure creates a closed magnetic circuit Notice for TAIYO YUDEN products Please read this notice before using the TAIYO YUDEN products. REMINDERS Product information in this catalog is as of October 200. All of the contents specified herein are

More information

Tornado Series selection SW TiCN HSS Co FAX VL PM

Tornado Series selection SW TiCN HSS Co FAX VL PM Metal Band Saw Blades Tornado Series selection SW TiCN HSS Co FAX VL PM Selection Chart Selection Chart Solids 3 Selection Teeth 4 note 1) Structurals, Tubing H section steels Light gauge steels Tube Products

More information

メタルバンドソー

メタルバンドソー Metal Band Saw Blades Tornado Series selection TiCN HSS Co FAX FMX PM VL Selection Chart Selection Chart Solids Selection Teeth 3 note 1) Structurals, Tubing H section steels Light gauge steels Tube 4

More information

LC304_manual.ai

LC304_manual.ai Stick Type Electronic Calculator English INDEX Stick Type Electronic Calculator Instruction manual INDEX Disposal of Old Electrical & Electronic Equipment (Applicable in the European Union

More information

…X…C…b…`A001_212

…X…C…b…`A001_212 RoHS compliant ITERAL STRUCTURE FEATURES RoHS compliant Meets EIAJ SP standard outline dimensions (B type) Low profile design of 2.5 mm 12 types of 1, 2, 4, 6, or 1 bit with either gull wing or J-hook

More information

5 11 3 1....1 2. 5...4 (1)...5...6...7...17...22 (2)...70...71...72...77...82 (3)...85...86...87...92...97 (4)...101...102...103...112...117 (5)...121...122...123...125...128 1. 10 Web Web WG 5 4 5 ²

More information

WARNING To reduce the risk of fire or electric shock,do not expose this apparatus to rain or moisture. To avoid electrical shock, do not open the cabi

WARNING To reduce the risk of fire or electric shock,do not expose this apparatus to rain or moisture. To avoid electrical shock, do not open the cabi ES-600P Operating Instructions WARNING To reduce the risk of fire or electric shock,do not expose this apparatus to rain or moisture. To avoid electrical shock, do not open the cabinet. Refer servicing

More information

I N S T R U M E N T A T I O N & E L E C T R I C A L E Q U I P M E N T box number basic type Standard Specification Material of Enclosure Material of F

I N S T R U M E N T A T I O N & E L E C T R I C A L E Q U I P M E N T box number basic type Standard Specification Material of Enclosure Material of F 01 Flameproof Junction Box Junction Box Series Our junction boxes are designed and manufactured based on the Recommended Practices for Explosion-Protected Electrical Installations in General Industries

More information

…X…C…b…`A001_212

…X…C…b…`A001_212 SA- RoHS compliant INTERNAL STRUCTURE FEATURES RoHS compliant Low profile of. mm Wide variety (top or side setting, or positions, J-hook, gull wing or through hole pins) to choose from Easy to recognize

More information

IEC :2014 (ed. 4) の概要 (ed. 2)

IEC :2014 (ed. 4) の概要 (ed. 2) IEC 60601-1-2:2014 (ed. 4) (ed. 2) e 2018 4 2 1 1 2 / 1 2.1............... 2 2.2............... 3 2.3.................. 4 3 6 4 6 4.1.................. 6 4.1.1............... 7 4.1.2....... 7 4.1.3............

More information

Microsoft Word - PCM TL-Ed.4.4(特定電気用品適合性検査申込のご案内)

Microsoft Word - PCM TL-Ed.4.4(特定電気用品適合性検査申込のご案内) (2017.04 29 36 234 9 1 1. (1) 3 (2) 9 1 2 2. (1) 9 1 1 2 1 2 (2) 1 2 ( PSE-RE-101/205/306/405 2 PSE-RE-201 PSE-RE-301 PSE-RE-401 PSE-RE-302 PSE-RE-202 PSE-RE-303 PSE-RE-402 PSE-RE-203 PSE-RE-304 PSE-RE-403

More information

I N S T R U M E N T A T I O N & E L E C T R I C A L E Q U I P M E N T STW Symbol Symbol otary switch) 05 otary switch Symbol angle of notch 181

I N S T R U M E N T A T I O N & E L E C T R I C A L E Q U I P M E N T STW Symbol Symbol otary switch) 05 otary switch Symbol angle of notch 181 These items are using an aluminum alloy cast, so the weight is corrosion-resistant and excel halo tolerance and is light-weight and it's about 1/3 compared with conventional cast iron and made of steel

More information

利隆塑料

利隆塑料 w w w. d g p e n g x u. c o m TECHNO PLASTICS GUIDE TECHNO ABS TECHNO MUH TECHNO AES EXCELLOY SANREX Grade Choices Flow Sheet TECHNO MUH TECHNO MUH Molding Condistions Our resin products represented

More information

alternating current component and two transient components. Both transient components are direct currents at starting of the motor and are sinusoidal

alternating current component and two transient components. Both transient components are direct currents at starting of the motor and are sinusoidal Inrush Current of Induction Motor on Applying Electric Power by Takao Itoi Abstract The transient currents flow into the windings of the induction motors when electric sources are suddenly applied to the

More information

- 1 -

- 1 - - 1 - - 2 - - 3 - - 4 - - 5 - - 6 - - 7 - - 8 - - 9 - - 10 - - 11 - - 12 - - 13 - - 14 - - 15 - 1 2 1-16 - 2 3 4 5 6 7-17 - 1 2 1 2 3 4-18 - 1 2 3 4 1 2-19 - 1 2 3 1 2-20 - 3 4 5 6 7 1-21 - 1 2 3 4-22

More information

ユーザーズマニュアル

ユーザーズマニュアル 1 2 3 4 This product (including software) is designed under Japanese domestic specifications and does not conform to overseas standards. NEC *1 will not be held responsible for any consequences resulting

More information

音響部品アクセサリ本文(AC06)PDF (Page 16)

音響部品アクセサリ本文(AC06)PDF (Page 16) Guide for Electret Condenser Microphones A microphone as an audio-electric converting device, whose audio pickup section has a structure of a condenser consisting of a diaphragm and a back plate opposite

More information

Huawei G6-L22 QSG-V100R001_02

Huawei  G6-L22 QSG-V100R001_02 G6 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 1 2 3 17 4 5 18 UI 100% 8:08 19 100% 8:08 20 100% 8:08 21 100% 8:08 22 100% 8:08 ********** 23 100% 8:08 Happy birthday! 24 S S 25 100% 8:08 26 http://consumer.huawei.com/jp/

More information

内蔵ハードディスクユニット-20GB (PG-HD2E4H) 内蔵ハードディスクユニット-40GB (PG-HD4E4H)取扱説明書 HARD DISK DRIVE 20GB(PG-HD2E4H) HARD DISK DRIVE 40GB(PG-HD4E4H) USER'S GUIDE

内蔵ハードディスクユニット-20GB (PG-HD2E4H) 内蔵ハードディスクユニット-40GB (PG-HD4E4H)取扱説明書 HARD DISK DRIVE 20GB(PG-HD2E4H)  HARD DISK DRIVE 40GB(PG-HD4E4H) USER'S GUIDE B7FY-0351-02 J E J 1 J 1 2 3 2 4 J 3 4 Preface Thank you very much for purchasing the hard disk drive. This hard disk drive provides a IDE interface and can be installed in the 3.5-inch storage bay of

More information

How to read the marks and remarks used in this parts book. Section 1 : Explanation of Code Use In MRK Column OO : Interchangeable between the new part

How to read the marks and remarks used in this parts book. Section 1 : Explanation of Code Use In MRK Column OO : Interchangeable between the new part Reservdelskatalog MIKASA MVB-85 rullvibrator EPOX Maskin AB Postadress Besöksadress Telefon Fax e-post Hemsida Version Box 6060 Landsvägen 1 08-754 71 60 08-754 81 00 info@epox.se www.epox.se 1,0 192 06

More information

FC741E2_091201

FC741E2_091201 T101-1587-04 1 2 2 0 0 9 2 0 0 8 0 9 0 1 0 5 0 9 1 4 0 5 1 0 5 5 1 2 3 4 4 5 6 7 8 9 1 2 3 0 3 3 0 2 1 1 5 0 1 3 3 3 0 2 0 3 0 3 4 0 9 1 1 0 9 0 9 1 1 5

More information

How to read the marks and remarks used in this parts book. Section 1 : Explanation of Code Use In MRK Column OO : Interchangeable between the new part

How to read the marks and remarks used in this parts book. Section 1 : Explanation of Code Use In MRK Column OO : Interchangeable between the new part Reservdelskatalog MIKASA MT65H vibratorstamp EPOX Maskin AB Postadress Besöksadress Telefon Fax e-post Hemsida Version Box 6060 Landsvägen 1 08-754 71 60 08-754 81 00 info@epox.se www.epox.se 1,0 192 06

More information

How to read the marks and remarks used in this parts book. Section 1 : Explanation of Code Use In MRK Column OO : Interchangeable between the new part

How to read the marks and remarks used in this parts book. Section 1 : Explanation of Code Use In MRK Column OO : Interchangeable between the new part Reservdelskatalog MIKASA MVC-50 vibratorplatta EPOX Maskin AB Postadress Besöksadress Telefon Fax e-post Hemsida Version Box 6060 Landsvägen 1 08-754 71 60 08-754 81 00 info@epox.se www.epox.se 1,0 192

More information

How to read the marks and remarks used in this parts book. Section 1 : Explanation of Code Use In MRK Column OO : Interchangeable between the new part

How to read the marks and remarks used in this parts book. Section 1 : Explanation of Code Use In MRK Column OO : Interchangeable between the new part Reservdelskatalog MIKASA MCD-L14 asfalt- och betongsåg EPOX Maskin AB Postadress Besöksadress Telefon Fax e-post Hemsida Version Box 6060 Landsvägen 1 08-754 71 60 08-754 81 00 info@epox.se www.epox.se

More information

I N S T R U M E N T A T I O N & E L E C T R I C A L E Q U I P M E N T Pressure-resistant gasket type retreat method effective bulk compressibility Fro

I N S T R U M E N T A T I O N & E L E C T R I C A L E Q U I P M E N T Pressure-resistant gasket type retreat method effective bulk compressibility Fro Cable Gland This is the s to use for Cable Wiring in the hazardous location. It is much easier to install and maintenance and modification compared with Conduit Wiring with Sealing Fitting. The Standard

More information

! " # $ % & ' ( ) +, -. / 0 1 2 3 4 5 6 7 8 9 : ; < = >? @ A B C D E F G H I J K L M N O P Q R S T U V W X Y Z [ ] ^ _ ` a b c d e f h i j k l m n o p q r s t u v w x y z { } ~ This product is

More information

(1) (2) (3) (4) (5) (6) (7) (8) (9) PLC PLC LAN MASTER PLC LAN MASTER PLC LAN MASTER PLC LAN MASTER PLC LAN MASTER MASTER MASTER PLC LAN PLC LAN PLC LAN MASTER PLC LAN MASTER MASTER TERMINAL MASTER TERMINAL

More information

DIN Connector_p2-25.qxd

DIN Connector_p2-25.qxd INDEX 1 DIN Connectors Varieties of DIN Connectors, Kinked Contact and One Touch Lock Metal Tab Kinked Contacts One Touch Lock Metal Tabs 2 Spec Sheet Soldering/Wire wrapping type Pitch Rated current 3A

More information

1 2 3

1 2 3 INFORMATION FOR THE USER DRILL SELECTION CHART CARBIDE DRILLS NEXUS DRILLS DIAMOND DRILLS VP-GOLD DRILLS TDXL DRILLS EX-GOLD DRILLS V-GOLD DRILLS STEEL FRAME DRILLS HARD DRILLS V-SELECT DRILLS SPECIAL

More information

untitled

untitled 1.0 1. Display Format 8*2 Character 2. Power Supply 3.3V 3. Overall Module Size 30.0mm(W) x 19.5mm(H) x max 5.5mm(D) 4. Viewing Aera(W*H) 27.0mm(W) x 10.5mm(H) 5. Dot Size (W*H) 0.45mm(W) x 0.50mm(H) 6.

More information

チョークコイル・リアクタ

チョークコイル・リアクタ THIN TRNSORMRS (MPT TYP) OMSTI(JPN) U S I TYP MPT MPT series are available for the thinner-sized sets and suit to I standard. H MPT I KS5535 KS6435 KS7235 KS7250 KS7270 KS9640 KS9660 KS9680 KS00 75.0 67.0

More information

137. Tenancy specific information (a) Amount of deposit paid. (insert amount of deposit paid; in the case of a joint tenancy it should be the total am

137. Tenancy specific information (a) Amount of deposit paid. (insert amount of deposit paid; in the case of a joint tenancy it should be the total am 13Fast Fair Secure PRESCRIBED INFORMATION RELATING TO TENANCY DEPOSITS* The Letting Protection Service Northern Ireland NOTE: The landlord must supply the tenant with the Prescribed Information regarding

More information

How to read the marks and remarks used in this parts book. Section 1 : Explanation of Code Use In MRK Column OO : Interchangeable between the new part

How to read the marks and remarks used in this parts book. Section 1 : Explanation of Code Use In MRK Column OO : Interchangeable between the new part Reservdelskatalog MIKASA MVC-88 vibratorplatta EPOX Maskin AB Postadress Besöksadress Telefon Fax e-post Hemsida Version Box 6060 Landsvägen 1 08-754 71 60 08-754 81 00 info@epox.se www.epox.se 1,0 192

More information

2015 Template Japanese A4

2015 Template Japanese A4 Liqualloy TM Toroidal Coil Technical Data Sheet ALPS ALPINE CO., LTD. リカロイ TM トロイダルコイル Liqualloy TM Toroidal Coil 特長 / Features (1) 100kHz 以上のスイッチング電源に対応 (2) 周波数特性が良好 (3) 当社オリジナルの軟磁性アモルファス材料リカロイ TM を用いることで超低損失を実現このため発熱が低減でき電源効率改善を実現

More information

PC_14ZY6_BFT150A_US_ indd

PC_14ZY6_BFT150A_US_ indd PARTS CATALOG BFT 0A OB NO.00-ZY- US Instruction for use of parts catalogue This parts catalogue was prepared based on the latest information available as of October,. See the Service Bulletin for any

More information

高周波同軸コネクタ

高周波同軸コネクタ RF circuit ANT Probe Signal in Signal out Probe Signal out Signal in RF circuit ANT Probe Probe Signal in Signal out Signal out Signal in RF ANT. RF ANT. Probe Probe Signal out Signal out Signal in Signal

More information

untitled

untitled SUBJECT: Applied Biosystems Data Collection Software v2.0 v3.0 Windows 2000 OS : 30 45 Cancel Data Collection - Applied Biosystems Sequencing Analysis Software v5.2 - Applied Biosystems SeqScape Software

More information

TH-47LFX60 / TH-47LFX6N

TH-47LFX60 / TH-47LFX6N TH-47LFX60J TH-47LFX6NJ 1 2 3 4 - + - + DVI-D IN PC IN SERIAL IN AUDIO IN (DVI-D / PC) LAN, DIGITAL LINK AV IN AUDIO OUT 1 11 2 12 3 13 4 14 5 6 15 7 16 8 17 9 18 10 19 19 3 1 18 4 2 HDMI AV OUT

More information

Motivation and Purpose There is no definition about whether seatbelt anchorage should be fixed or not. We tested the same test conditions except for t

Motivation and Purpose There is no definition about whether seatbelt anchorage should be fixed or not. We tested the same test conditions except for t Review of Seatbelt Anchorage and Dimensions of Test Bench Seat Cushion JASIC Motivation and Purpose There is no definition about whether seatbelt anchorage should be fixed or not. We tested the same test

More information

K02LE indd

K02LE indd I Linear Stage Table of Contents 1. Features... 1 2. Description of part Number... 1 3. Maximum Speed Limit... 2 4. Specifications... 3 5. Accuracy Grade... 4 6. Motor and Motor Adaptor Flange... 4 6-1

More information

Direct Motor Drive Lead Screws / Resin Lead Screw type RM / RM RM Resin Lead Screw type RM / Resin MoBo 2 MRH 2 Features A 2-phase Stepping Motor is m

Direct Motor Drive Lead Screws / Resin Lead Screw type RM / RM RM Resin Lead Screw type RM / Resin MoBo 2 MRH 2 Features A 2-phase Stepping Motor is m RM Resin Lead Screw typerm / Resin MoBo MRH Features A -phase Stepping Motor is mounted directly onto the shaft end of a Resin Lead Screw, which is multi-use product. Lead Screw Shaft is ideally constructed

More information

1. Database&Logic 2. 3. Word/Excel/PPT/PDF&Web Ultimate Dictionary 4. Jukkou&Rewrite 5. Convenience&Safety 6. Chinese&Korean 7. Support&Consultation 8

1. Database&Logic 2. 3. Word/Excel/PPT/PDF&Web Ultimate Dictionary 4. Jukkou&Rewrite 5. Convenience&Safety 6. Chinese&Korean 7. Support&Consultation 8 www.jukkou.com 1. Database&Logic 2. 3. Word/Excel/PPT/PDF&Web Ultimate Dictionary 4. Jukkou&Rewrite 5. Convenience&Safety 6. Chinese&Korean 7. Support&Consultation 8. Jukkou Z 9. Introduction Example 10.

More information

0 PARTS CATALOG BFT A BFT 0A OB NO.00-ZYET- US Instruction for use of parts catalogue This parts catalogue was prepared based on the latest information available as of October, 0. See the Service Bulletin

More information

2 3 12 13 6 7

2 3 12 13 6 7 2 8 17 42ZH700046ZH700052ZH7000 28 43 54 63 74 89 2 3 12 13 6 7 3 4 11 21 34 63 65 8 17 4 11 4 55 12 12 10 77 56 12 43 43 13 30 43 43 43 43 10 45 14 25 9 23 74 23 19 24 43 8 26 8 9 9 4 8 30 42 82 18 43

More information

2

2 2 3 ( 4 1) ( 49 8) ( 49 82) ( 49 822) ( 49 823) ( 49 14) ( 49 14) ( 49 14) 49 14 ( 49 17) ( 49 202) IEEE802.11 ( 49 201) IEEE802.11 Bluetooth 5GHz ( 49 203) IEEE802.11 ( 49 204) 5GHz ( 49 21) IEEE802.11

More information

Z7000操作編_本文.indb

Z7000操作編_本文.indb 2 8 17 37Z700042Z7000 46Z7000 28 42 52 61 72 87 2 3 12 13 6 7 3 4 11 21 34 61 8 17 4 11 4 53 12 12 10 75 18 12 42 42 13 30 42 42 42 42 10 62 66 44 55 14 25 9 62 65 23 72 23 19 24 42 8 26 8 9 9 4 11 18

More information

Mikio Yamamoto: Dynamical Measurement of the E-effect in Iron-Cobalt Alloys. The AE-effect (change in Young's modulus of elasticity with magnetization

Mikio Yamamoto: Dynamical Measurement of the E-effect in Iron-Cobalt Alloys. The AE-effect (change in Young's modulus of elasticity with magnetization Mikio Yamamoto: Dynamical Measurement of the E-effect in Iron-Cobalt Alloys. The AE-effect (change in Young's modulus of elasticity with magnetization) in the annealed state of iron-cobalt alloys has been

More information

2

2 8 23 26A800032A8000 31 37 42 51 2 3 23 37 10 11 51 4 26 7 28 7 8 7 9 8 5 6 7 9 8 17 7 7 7 37 10 13 12 23 21 21 8 53 8 8 8 8 1 2 3 17 11 51 51 18 23 29 69 30 39 22 22 22 22 21 56 8 9 12 53 12 56 43 35 27

More information

2

2 8 22 19A800022A8000 30 37 42 49 2 3 22 37 10 11 49 4 24 27 7 49 7 8 7 9 8 5 6 7 9 8 16 7 7 7 37 10 11 20 22 20 20 8 51 8 8 9 17 1 2 3 16 11 49 49 17 22 28 48 29 33 21 21 21 21 20 8 10 9 28 9 53 37 36 25

More information

Tab 5, 11 Tab 4, 10, Tab 3, 9, 15Tab 2, 8, 14 Tab 1, 7, 13 2

Tab 5, 11 Tab 4, 10, Tab 3, 9, 15Tab 2, 8, 14 Tab 1, 7, 13 2 COMPANION 20 MULTIMEDIA SPEAKER SYSTEM Owner s Guide Tab 5, 11 Tab 4, 10, Tab 3, 9, 15Tab 2, 8, 14 Tab 1, 7, 13 2 Tab1, 7, 13 Tab 2, 8, 14 Tab 3, 9, 15 Tab 4, 10, Tab 5, 11 This product conforms to all

More information

SCR8-17XX Technical Data Optical Magnetic Brushless Coreless Encoder Motor Unitmm 5 Number of commutator segments Brushes Precious Metal Bearings Slee

SCR8-17XX Technical Data Optical Magnetic Brushless Coreless Encoder Motor Unitmm 5 Number of commutator segments Brushes Precious Metal Bearings Slee CORELESS MOTOR SCR8-17 SCR10-17 SCR10-25 SCR12-13 SCR12-18 SCR12-26 SCR13-20 SCR13-28 NEW SCR16-25 SCR16-35 SCR17-25 SCR17-35 SCR18-37 SC21-37 SC24-32 Smaller and higher-performance motors realized by

More information

01.eps

01.eps 444 SumiTurn T-REX Tool Holders Cost reduction for copying with unique multiple cornered insert Carbide inserts, cermet inserts and 4 types of breakers are available. Expansion of our popular steel turning

More information

MIDI_IO.book

MIDI_IO.book MIDI I/O t Copyright This guide is copyrighted 2002 by Digidesign, a division of Avid Technology, Inc. (hereafter Digidesign ), with all rights reserved. Under copyright laws, this guide may not be duplicated

More information

6 4 45 7ZS 5 59 7 8 94 05 4 5 6 4 5 5 6 8 8 40 45 48 56 60 64 66 66 68 7 78 80 8 7 8 0 0 0 90 0 57 64 69 66 66 69 0 4 4 4 4 4 0 7 48 5 4 4 5 4 4 4 7 46 46 6 46 8 46 48 46 46 4 46 46 4 4 5 4 6 4 9 9 0

More information

untitled

untitled TZ-BDT910M TZ-BDT910F TZ-BDT910P μ μ μ μ TM VQT3F51-1 l l l [HDD] [BD-RE] [BD-R] [DVD-V] [BD-V] [RAM] [CD] [SD] [-R] [USB] [-RW] [RAM AVCREC ] [-R AVCREC ] [RAM VR ][-R VR ] [-RW VR ] [-R V ] [-RW

More information

080906_…o…−…^…b…vVSCW

080906_…o…−…^…b…vVSCW Thyristor Type Single-Phase Power Regulator 2030 A 6A 150200A TOKYO RIKOSHA CO., LTD Latest VARITAP VSCW Series Achieved 1/2 the width (our company comparison). Free Power source of 100 to 240V specification.cover-type

More information

00_1512_SLIMLINE_BOOK.indb

00_1512_SLIMLINE_BOOK.indb PIECE type SLIM type Imbalance value Less interference type, ideal for deep machining Ideal for drilling 2 PIECE REGULAR type Rigidity value Nozzle type When compared to the slim type, it has more rigidity

More information

/ Motor Specifications Direct Motor Drive Ball Screws / Precision Ball Screw type MB / MB MB Precision Ball Screw type MB / MoBo C3 5 5 Features A 5-p

/ Motor Specifications Direct Motor Drive Ball Screws / Precision Ball Screw type MB / MB MB Precision Ball Screw type MB / MoBo C3 5 5 Features A 5-p / Motor Specifications MB Precision Ball Screw type MB / MoBo C3 5 5 Features A 5-pahse Stepping Motor is mounted directly onto the shaft end of a C3 grade precision Ball Screw, which is suitable for high

More information

6 4 4 9RERE6RE 5 5 6 7 8 9 4 5 6 4 4 5 6 8 4 46 5 7 54 58 60 6 69 7 8 0 9 9 79 0 4 0 0 4 4 60 6 9 4 6 46 5 4 4 5 4 4 7 44 44 6 44 8 44 46 44 44 4 44 0 4 4 5 4 8 6 0 4 0 4 4 5 45 4 5 50 4 58 60 57 54

More information

2

2 8 24 32C800037C800042C8000 32 40 45 54 2 3 24 40 10 11 54 4 7 54 30 26 7 9 8 5 6 7 9 8 18 7 7 7 40 10 13 12 24 22 22 8 55 8 8 8 8 1 2 3 18 11 54 54 19 24 30 69 31 40 57 23 23 22 23 22 57 8 9 30 12 12 56

More information

Features Features FeaturesThread milling cutters 1

Features Features FeaturesThread milling cutters 1 Thread Milling Cutter Series NEW SIZES Features Features FeaturesThread milling cutters 1 Threading process (view from above) CUTTER Series PLANET Machining Technique Guide to (Tool Specification) Icons

More information

The Japanese economy in FY2015 suffered from sluggish growth in individual consumption, while the foreign exchange market remained unstable with high volatility. Even in such an economic environment, MSF

More information

6 4 45 ZS7ZS4ZS 5 59 7 8 94 05 4 5 6 4 5 5 6 8 8 40 45 48 56 60 64 66 66 68 7 78 80 8 7 8 0 0 0 90 0 0 4 4 4 4 6 57 64 69 66 66 66 69 4 0 7 48 5 4 4 5 4 4 4 7 46 46 6 46 8 46 48 46 46 4 46 46 4 4 5 4

More information

A5 PDF.pwd

A5 PDF.pwd DV DV DV DV DV DV 67 1 2016 5 383 DV DV DV DV DV DV DV DV DV 384 67 1 2016 5 DV DV DV NPO DV NPO NPO 67 1 2016 5 385 DV DV DV 386 67 1 2016 5 DV DV DV DV DV WHO Edleson, J. L. 1999. The overlap between

More information

H8000操作編

H8000操作編 8 26 35 32H800037H800042H8000 49 55 60 72 2 3 4 48 7 72 32 28 7 8 9 5 7 9 22 43 20 8 8 8 8 73 8 13 7 7 7 55 10 49 49 13 37 49 49 49 49 49 49 12 50 11 76 8 24 26 24 24 6 1 2 3 18 42 72 72 20 26 32 80 34

More information

AD8212: 高電圧の電流シャント・モニタ

AD8212: 高電圧の電流シャント・モニタ 7 V typ 7 0 V MSOP : 40 V+ V SENSE DC/DC BIAS CIRCUIT CURRENT COMPENSATION I OUT COM BIAS ALPHA 094-00 V PNP 0 7 V typ PNP PNP REV. A REVISION 007 Analog Devices, Inc. All rights reserved. 0-9 -- 0 40

More information

2

2 8 23 32A950S 30 38 43 52 2 3 23 40 10 33 33 11 52 4 52 7 28 26 7 8 8 18 5 6 7 9 8 17 7 7 7 38 10 12 9 23 22 22 8 53 8 8 8 8 1 2 3 17 11 52 52 19 23 29 71 29 41 55 22 22 22 22 22 55 8 18 31 9 9 54 71 44

More information

0810_UIT250_soto

0810_UIT250_soto UIT UNIMETER SERIES 250 201 Accumulated UV Meter Digital UV Intensity Meter Research & Development CD Medical Biotech Sterilization Exposure Bonding Manufacturing Curing Production Electronic Components

More information

OPA134/2134/4134('98.03)

OPA134/2134/4134('98.03) OPA OPA OPA OPA OPA OPA OPA OPA OPA TM µ Ω ± ± ± ± + OPA OPA OPA Offset Trim Offset Trim Out A V+ Out A Out D In +In V+ Output In A +In A A B Out B In B In A +In A A D In D +In D V NC V +In B V+ V +In

More information

Thread Milling Cutter Series

Thread Milling Cutter Series Thread Milling Cutter Series Features Features FeaturesThread milling cutters 1 Planet Cutter Series Threading process (view from above) Machining Technique Guide to (Tool Specification) Icons Tool Materials

More information

32R22J NN332AEVB

32R22J NN332AEVB 32R22J Total Pages 4 Page The product specifications described in this book are subject to change without notice for the product which is currently under development. At the final stage of your design,

More information

PRODUCT INFORMATION Highly Efficient FXS Carbide Ball Nose End Mills Vol. 3 PAT.P. FXS-EBT FXS-LS-EBT FXS-PC-EBT FXS-EBM

PRODUCT INFORMATION Highly Efficient FXS Carbide Ball Nose End Mills Vol. 3 PAT.P. FXS-EBT FXS-LS-EBT FXS-PC-EBT FXS-EBM PRODUCT INFORMATION Highly Efficient FXS Carbide Ball Nose End Mills Vol. 3 PAT.P. FXS-EBT FXS-LS-EBT FXS-PC-EBT FXS-EBM 3 Flutes Series Features Thanks to 3 flutes ball nose geometry, all of that reach

More information

LM mA 低ドロップアウト・リニア・レギュレータ

LM mA 低ドロップアウト・リニア・レギュレータ 800mA 800mA LM1117I 800mA LM1117 Chris Russell LM1117 800mA 1.2V LM1117 LM317 LM1117 2 1.25V 13.8V 1.8V 2.5V 2.85V 3.3V 5V 5 LM1117 1 LM1117 LLP TO-263 SOT-223 TO-220 TO-252 10 F 19970801 23900 DS100919

More information

Fig. 1 Schematic construction of a PWS vehicle Fig. 2 Main power circuit of an inverter system for two motors drive

Fig. 1 Schematic construction of a PWS vehicle Fig. 2 Main power circuit of an inverter system for two motors drive An Application of Multiple Induction Motor Control with a Single Inverter to an Unmanned Vehicle Propulsion Akira KUMAMOTO* and Yoshihisa HIRANE* This paper is concerned with a new scheme of independent

More information

MKS-05 "TERRA-Pプラス 日本語訳取扱説明書

MKS-05 TERRA-Pプラス 日本語訳取扱説明書 MKS-05 "TERRA-P+" BICT.412129.021 KE Sparing-Vist Center Sparing-Vist Center ECOTEST (+38 032) 242-15-15 (+38 032) 242-20-15 sales@ecotest.ua 18 ( ) 2 1. 3 2. 3 3. 4 4. 4 5. 6 6. 7 7. 11 8. 11 9. 11 10.

More information

untitled

untitled VQT3B82-1 DMP-BDT110 μ μ μ 2 VQT3B82 ÇÕÇ¹Ç Ç +- VQT3B82 3 4 VQT3B82 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 ij SD 1 2 3 4 5 6 7 8 Í VQT3B82 5 BD DVD CD SD USB 6 VQT3B82 2 ALL 1 2 4 VQT3B82 7

More information

植物23巻2号

植物23巻2号 (J.SHITA)23(2):37-43. 2011. 37 520-0531 1-13-15 Operation Should be Automated and not so in Plant Factory for Leafy Vegetables Touichi OGURA Goodgoal Inc, 1-13-15 Suimei Otsu-shi, Shiga 520-0531, Japan

More information

™…

™… Review The Secret to Healthy Long Life Decrease in Oxidative and Mental Stress My motto is Health is not all. But nothing can be done without health. Health is the most important requisite for all human

More information

_念3)医療2009_夏.indd

_念3)医療2009_夏.indd Evaluation of the Social Benefits of the Regional Medical System Based on Land Price Information -A Hedonic Valuation of the Sense of Relief Provided by Health Care Facilities- Takuma Sugahara Ph.D. Abstract

More information

combat_manual_site.ai

combat_manual_site.ai 131 71 71 71 71 71 71 71 71 71 71 71 7 1 71 71 71 71 71 71 7 1 71 71 71 71 71 71 71 71 71 71 7 1 71 7 1 71 71 71 71 71 71 71 71 71 71 71 7 www.sven.1 7 13RUS 1 71 71 71 71 71 71 71 71 71 71 7 1 71 7 1

More information

96R22J NN396AEVB

96R22J NN396AEVB 96R22J Total Pages 4 Page The product specifications described in this book are subject to change without notice for the product which is currently under development. At the final stage of your design,

More information

ユーザーズマニュアル

ユーザーズマニュアル 1 2 3 This product (including software) is designed under Japanese domestic specifi cations and does not conform to overseas standards. NEC *1 will not be held responsible for any consequences resulting

More information

μ μ DMR-BZT700 DMR-BZT600 μ TM VQT3C03-2B ! ! l l l [HDD] [BD-RE] [BD-R] [DVD-V] [BD-V] [RAM] [CD] [SD] [-R] [USB] [-RW] [RAM AVCREC ] [-R AVCREC ] [RAM VR ][-R VR ] [-RW VR ] [-R V ] [-RW V ] [DVD-V]

More information

修士論文

修士論文 2004 Decay of timber and its mechanical characteristic 1075015 1075015 1. 1 1. 2. 3. 4. 5. 4.5. 2. JIS 3. 3.1 3.1.1 ( ) ( ) i 3.1.2 3.1.3 10 3.2 ( 3% ) 4 3% ii Decay of timber and its mechanical characteristic

More information

19_22_26R9000操作編ブック.indb

19_22_26R9000操作編ブック.indb 8 19R900022R900026R9000 25 34 44 57 67 2 3 4 10 37 45 45 18 11 67 25 34 39 26 32 43 7 67 7 8 7 9 8 5 7 9 21 18 19 8 8 70 8 19 7 7 7 45 10 47 47 12 47 11 47 36 47 47 36 47 47 24 35 8 8 23 12 25 23 OPEN

More information

KOMET KUB K2® 小径対応ヘッド交換式ドリル

KOMET KUB K2® 小径対応ヘッド交換式ドリル KOMET KUB K2 Replaceable Head Drill for Tiny Diameters With this replaceable head system for the doublecutting KUB K2, KOMET has introduced an ingenious system of replaceable drill heads. These now also

More information

-5 DMP-BV300 μ μ l μ l l +- l l j j j l l l l l l l l l l l l l Ë l l l l l l l l l l l l l l l l l l l l l l l BD DVD CD SD USB 2 ALL 1 2 4 l l DETACH ATTACH RELEASE DETACH ATTACH DETACH ATTACH RELEASE

More information

H1-4_0718.ai

H1-4_0718.ai Eyelash extension enters the age of comfort Comfort Usability Riche was developed by Takara Belmont using knowledge from not only the salon industry but also medical areas such as ophthalmology. A series

More information

VQT3A26-1 DMR-T2000R μ μ μ ! R ! l l l [HDD] [BD-RE] [BD-R] [BD-V] [RAM] [-R] [-R]DL] [-RW] [DVD-V] [CD] [SD] [USB] [RAM AVCREC ] [-R AVCREC ] [-R]DL AVCREC ] [RAM VR ][-R VR ] [-R]DL VR ] [-RW VR ]

More information

インターネット接続ガイド v110

インターネット接続ガイド v110 1 2 1 2 3 3 4 5 6 4 7 8 5 1 2 3 6 4 5 6 7 7 8 8 9 9 10 11 12 10 13 14 11 1 2 12 3 4 13 5 6 7 8 14 1 2 3 4 < > 15 5 6 16 7 8 9 10 17 18 1 2 3 19 1 2 3 4 20 U.R.G., Pro Audio & Digital Musical Instrument

More information

DZ-GX20/DZ-MV780取扱説明書(上巻)

DZ-GX20/DZ-MV780取扱説明書(上巻) DZ-GX20 DZ-MV780(S) DZ-MV780(R) DZ-MV780(A) Important Information WARNING : To prevent fire or shock hazard, do not expose this unit to rain or moisture. WARNING : To prevent fire or shock hazard, use

More information

speax55CL 4版

speax55CL 4版 1 2 3 4 5 6 100m 7 8 9 10 11 12 13 14 15 16 17 4 1 5 2 3 6 1 4 2 5 3 6 7 8 0 9 18 19 20 21 1 2 3 4 1 2 22 23 2 1 1 2 3 4 5 6 7 8 24 25 1 2 3 4 5 26 1 2 3 4 5 6 1 2 3 4 5 6 7 7 8 8 27 1 2 3 4 1 2 3 5 4

More information

6 50G5S 3 34 47 56 63 http://toshibadirect.jp/room048/ 74 8 9 3 4 5 6 3446 4755 566 76373 7 37 3 8 8 3 3 74 74 79 8 30 75 0 0 4 4 0 7 63 50 50 3 3 6 3 5 4 4 47 7 48 48 48 48 7 36 48 48 3 36 37 6 3 3 37

More information