iStorage NS480ユーザーズガイド

Size: px

Start display at page:

Download "iStorage NS480ユーザーズガイド"

としなりすみい
7 years ago
Views:

1 7

8 Phoenix BIOS 4.0 Release 6.0.XXXX : CPU=Xeon Processor XXX MHz 0640K System RAM Passed 0127M Extended RAM Passed WARNING 0B60: DIMM group #1 has been disabled. : Press <F1> to resume, <F2> to setup

9 0200 Failure Fixed Disk Stuck Key Keyboard erro 0213 Keyboard locked - Unlock key sitch Monitor type does not match CMOS - Run SETUP System RAM Failed at offset Shado Ram Failed at offset Extended RAM Failed at address line System battery is dead - Replace and run SETUP System CMOS checksum bad - Default configuration used Passord checksum bad - Passords cleared System timer error Real time clock error Check date and time setting Previous boot incomplete - Default configuration used 0281 Memory size found by POST differd from EISA CMOS 02D0 System cache error - Cache disabled. 02D1 System Memory exceeds the CPU's caching limit. 02F4 EISA CMOS not rite able. 02F5 DMA Test Failed. 02F6 Softare NMI Failed. 02F7 Fail-safe Timer NMI Failed. 0B22 Processors are installed out of order. 0B28 Unsupported CPU detected on CPU Socket 1. 0B29 Unsupported CPU detected on CPU Socket 2.

10 0B42 Resource Conflict 0B43 Warning: IRQ not configured 0B45 System Configuration Data Write Error 0B60 0B61 0B62 0B63 0B64 0B65 0B66 0B67 0B68 0B69 0B6A 0B6B 0B6F 0B70 0B71 0B74 0B75 0B80 0B81 0B82 0B83 CPU1_DIMM1 has been disabled CPU1_DIMM2 has been disabled CPU1_DIMM3 has been disabled CPU1_DIMM4 has been disabled CPU1_DIMM5 has been disabled CPU1_DIMM6 has been disabled CPU2_DIMM1 has been disabled CPU2_DIMM2 has been disabled CPU2_DIMM3 has been disabled CPU2_DIMM4 has been disabled CPU2_DIMM5 has been disabled CPU2_DIMM6 has been disabled DIMM group ith error is enabled. The error occurred during temperature sensor reading. System Temperature out of the range. The error occurred during voltage sensor reading. System voltage out of the range. BMC Memory Test Failed. BMC Firmare Code Area CRC check failed. BMC core Hardare failure. BMC IBF or OBF check failed. 0B8A BMC SEL area full.

11 0B8B 0B8C 0B8D 0B8E 0B8F 0B90 0B91 0B92 0B93 0B94 0B95 0B96 0B97 BMC progress check timeout. BMC command access failed. Could not redirect the console - BMC Busy - Could not redirect the console - BMC Error - Could not redirect the console - BMC Parameter Error - BMC Platform Information Area corrupted. BMC update firmare corrupted. Internal Use Area of BMC FRU corrupted. BMC SDR Repository empty. IPMB signal lines do not respond. BMC FRU device failure. BMC SDR Repository failure. BMC SEL device failure. 0B98 BMC RAM test error. 0B99 BMC Fatal hardare error. 0B9A Management controller not responding. 0B9B 0B9C 0B9D 0B9E Private I2C bus not responding. BMC internal exception. BMC A/D timeout error. SDR repository corrupt. 0B9F SEL corrupt. 0BB0 SMBIOS - SROM data read error. 0BB1 SMBIOS - SROM data checksum bad.

12 0BD1 1st SMBus device Error detected. 0BD4 2nd SMBus device Error detected. 0BD7 3rd SMBus device Error detected. 0BDA 4th SMBus device Error detected. 0BDD 5th SMBus device Error detected. 0BE0 6th SMBus device Error detected Unsupported Processor Speed detected on CPU Slot Unsupported Processor Speed detected on CPU Slot NVRAM Cleared By Jumper 8151 Passord Cleared By Jumper 8160 Mismatch Processor Type/Speed detected on Processor Mismatch Processor Type/Speed detected on Processor 2. Expansion ROM not initialized - PCI Mass Storage Controller in slot xx H/W Configuration of BMC is corrupted.!!update BMC F/W Configuration by configuration tool!!!!refer to BMC configuration manual!! Memory Scramble mode disabled

13 Memory/battery problems ere detected. The adapter has recovered, but cached data as lost. Press any key to continue, or 'C' to load the configuration utility. Firmare version inconsistency as detected. The adapter has recovered, but cached data as lost. Press any key to continue, or 'C' to load the configuration utility. Foreign configuration(s) found on adapter Press any key to continue, or 'C' to load the configuration utility. Previous configuration cleared or missing Importing configuration created on MM/DD hh:mm Press any key to continue, or 'C' to load the configuration utility. An enclosure as found that contains both SAS and SATA drives, but this controller does not allo mixed drive types in a single enclosure. Please correct the problem then restart your system. Press any key to continue, or 'C' to load the configuration utility. SAS drives ere detected, but this controller does not support SAS drives. Please remove the SAS drives then restart your system. Press any key to continue, or 'C' to load the configuration utility. SATA drives ere detected, but this controller does not support SATA drives. Please remove the SATA drives then restart your system. Press any key to continue, or 'C' to load the configuration utility. Invalid SAS topology detected. Please check your cable configurations, repair the problem, and restart your system. The battery hardare is missing or malfunctioning, or the battery is unplugged. If you continue to boot the system, the battery-backed cache ill not function. Please contact technical support for assistance. Press 'D' to disable this arning (if your controller does not have a battery).

14 Your VDs that are configured for rite-back are temporarily running in rite-through mode. This is caused by the battery being charged, missing, or bad. Please allo battery to charge for 24 hours before evaluating battery for replacement. The folloing VDs are affected :XX Press any key to continue. Invalid SAS Address present in MFC data. Please program valid SAS Address, and restart your system. Some configured disks have been removed from your system, or are no longer accessible. Please check your cables and also ensure all disks are present. Press any key to continue, or 'C' to load the configuration utility. The folloing VDs have missing disks: xx If you proceed (or load the configuration utility), these VDs ill be marked OFFLINE and ill be inaccessible. Please check your cables and ensure all disks are present. Press any key to continue, or 'C' to load the configuration utility. The folloing VDs are missing: xx If you proceed (or load the configuration utility), these VDs ill be removed from your configuration. If you ish to use them at a later time, they ill have to be imported. If you believe these VDs should be present, please poer off your system and check your cables to ensure all disks are present. Press any key to continue, or 'C' to load the configuration utility. All of the disks from your previous configuration are gone. If this is an unexpected message, then please poer off your system and check your cables to ensure all disks are present. Press any key to continue, or 'C' to load the configuration utility.

15 The cache contains dirty data, but some VDs are missing or ill go offline, so the cached data can not be ritten to disk. If this is an unexpected error, then please poer off your system and check your cables to ensure all disks are present. If you continue, the data in cache ill be permanently discarded. Press 'X' to acknoledge and permanently destroy the cached data. Invalid memory configuration detected. Please contact your system support. System has halted. RAID Adapter FW Failed Validation!!! Adapter needs to be reflashed. Press any key to continue. Cache data as lost due to an unexpected poer-off or reboot during a rite operation, but the adapter has recovered. This could be due to memory problems, bad battery, or you may not have a battery installed. Press any key to continue or 'C' to load the configuration utility. Entering the configuration utility in this state ill result in drive configuration changes. Press 'Y' to continue loading the configuration utility or please poer off your system and check your cables to ensure all disks are present and reboot. Multibit ECC errors ere detected on the controller. DIMM on the controller needs replacement. If you continue, data corruption can occur. Press 'X' to continue or else poer off the system and replace the DIMM module and reboot. If you have replaced the DIMM please press 'X' to continue. Multiple Single-bit ECC errors ere detected during the previous boot of the controller. DIMM on the controller needs replacement. If you continue, data corruption can occur. Press 'X' to continue or else poer off the system and replace the DIMM module and reboot. If you have replaced the DIMM please press 'X' to continue.

16 Single-bit overflo ECC errors ere detected during the previous boot of the controller. DIMM on the controller needs replacement. If you continue, data corruption can occur. Press 'X' to continue or else poer off the system and replace the DIMM module and reboot. If you have replaced the DIMM please press 'X' to continue.

21 *** STOP: 0x A (0x , 0x , 0x , 0x80108E7A) IRQL_NOT_LESS_OR_EQUAL*** Address 80108E7A has base at _ ntoskrnl.exe

Express5800/R110a-1Hユーザーズガイド

Express5800/R110a-1Hユーザーズガイド 4 Phoenix BIOS 4.0 Release 6.0.XXXX : CPU=Xeon Processor XXX MHz 0640K System RAM Passed 0127M Extended RAM Passed WARNING 0B60: DIMM group #1 has been disabled. : Press to resume, to