基本 CMYK

Size: px
Start display at page:

Download "基本 CMYK"

Transcription

1

2 Ultra Miniaturized Linear Actuator Ultra Compact 1628 mm 630 mm Rated Thrust 1.56 kgf High Resolution m Unidirectional Repeatable Accuracy 320 m Bidirectional Repeatable Accuracy 525 m Bidirectional Positioning Accuracy 1050 m Special Features Ultra miniaturized AC servo linear actuators are the compact and light linear actuators, which enable precision positioning. The motor section adapts an AC servo motor of hollow structure and the encoder section adopts an optical rotary encoder with ultra miniaturization and high resolution. Together with these devices, the direct design without gearhead achieves the precision positioning of high resolution. MAB and MALB series utilizes ball screw to accomplish high speed and long life. MALS and MALB series are cost-effective models, which largely reduce the prices, but maintain the high precision positioning. The compact and light multifunctional driver was specially developed for this AC servo linier actuator. With the sinusoidal wave and gain low, this actuator has a smooth motion and positions itself without vibration, the most crucial for the linear actuator. The actuator is easily adaptable to be used in vacuum chambers or clean rooms, and can also be applied to a wide range of applications, such as production, inspection and experimental equipment in optical and semiconductor industries. Contents Reference to Model No.Drawing of Actuator FixingSystem ConfigurationP.2 Linear Actuator for General Environment MALS-D18 Series NEW Standard type (Cost-effective Model) P.3 MAS-D16 Series Standard Type P.4 MALS-D23 Series NEW Standard Type (Cost-effective Model) P.5 MAS-D23 Series Standard Type P.6 MALB-D28 Series NEW High Speed / Long Life Type(Cost-effective Model) P.7 MAB-D28 Series High Speed / Long Life Type P.8 Models for Special Environments MASC-D16 Series Linear Actuator for Clean Room P.9 MASC-D23 Series Linear Actuator for Clean Room P.10 MAVB-D28 Series High Vacuum P.11 MASG-D23 Series Chemical Cleanliness P.12 Cautions for Handling Products P.13 Control Driver LAD-01 Series NEW P.15 P.16 BSD-11, BSD-06 Series P.17 P.18 Cable P.19 P.20 Term Definition / Accuracy Measurement P.21 P.22 1

3 Model No. MAS - D23 H Type : : : : : : : S : Standard type LS : Standard type(cost-effective Model) B : Ball screw type LB : Ball screw type(cost-effective Model) SC : for clean room VB : for vacuum condition SG : for chemical cleanliness Outer diameter Tip shape 03: cable length is 200mm Standard cable length is 2m when no code is written at this position. H : Tip with flat point R : Tip with spherical point N : Tip with tapped hole (For MAB, MALB and MALS only) Drawing of Actuator Fixing Use an accompanying screw nut to fix the actuator to a locking plate. Accompanying screw nut for fixing the actuator Locking Plate Note 1) Use the accompanying screw nut to fix the actuator to your equipment. Desired accuracy may not be obtained when the actuator housing is clenched for fixing. Note 2) The malfunction of shaft slide is concerned when the hardness of locking plate is insufficient and the screw nut is tightened too strongly. System Configuration Positioning Controller Driver Cable AC AC Servo Linear Actuator DC24V DC24V Power = Products of our company 2

4 MALS-D18 Series NEW 6/ 10/ 20 mm 1.5 kgf Rated thrust 0.5 m Resolution Cost-Effective Model SF Tube Standard Type Nut Flat tip Original position with tapped hole type : 1.5 mm Add -03 at the last part of model number with order when 200 mm cable length is required. Specification Parameter Rated thrust Resolution Max speed Screw lead Unidirectional repeatable accuracy Bidirectional repeatable accuracy Bidirectional positioning accuracy Average reversal error Limit sensor Length Weight Diameter Model Flat tip : H type Spherical tip : R type Tapped hole : N type M2 with depth of 4 (Note 6) Note 1) Use the accompanying screw nut to fix the actuator to your equipment. Desired accuracy may not be obtained when the actuator housing is clenched for fixing. Note 2) The actuator shaft can receive a load in the both of forward and backward thrust directions. Use springs or something similar to apply pre-load to the shaft in either one direction at the operation. Backlash is concerned and desired accuracy may not be obtained when no pre-load is applied to the shaft. We perform the accuracy measurements by applying the pre-load of 800gf in the backward thrust direction at our shipping inspection. Please be careful not to place more than a rated trust in a forward thrust direction at a time of installation. Note 3) The actuator cable is not designed to withstand repeated bending stress. Please contact us if the cable receives repeated bending stress. Note 4) The encoders of these models have 2 channels only and have no Z phase. Note 5) As to the original position, refer to the page of term definition. Note 6) Torque loaded on a rod of actuator need to be less than 1 Nm when installing a screw to a hole in the tip of N type. Torque of over 1 Nm may cause a deterioration of actuator s precision. Safety Mechanism The damper system is set at the front end of stroke and limit sensor is installed at the rear end. Compatibility The mounting section of this linear actuator is compatible with manual micrometer. Special Driver Please use the driver LAD-01 series (Recommend), BSD-06 series which was specially developed for this actuator. Extension Cable The encoder is open collector type. The transmission distance may be extended by the use of LAD-01D-012 or BSD-06D-012 (good for line driver type) with an extension cable. 3

5 MAS-D16 Series 6/ 10/ 20 mm 2 kgf Rated thrust 0.25 m Resolution Spherical tip SF Tube Standard Type (Extra Fine) Nut Flat tip Original position Add -03 at the last part of model number with order when 200 mm cable length is required. Specification Parameter Model Rated thrust Resolution Max speed Screw lead Unidirectional repeatable accuracy Bidirectional repeatable accuracy Bidirectional positioning accuracy Average reversal error Limit sensor Length Weight Diameter Note 1) Use the accompanying screw nut to fix the actuator to your equipment. Desired accuracy may not be obtained when the actuator housing is clenched for fixing. Note 2) The actuator shaft can receive a load in the both of forward and backward thrust directions. Use springs or something similar to apply pre-load to the shaft in either one direction at the operation. Backlash is concerned and desired accuracy may not be obtained when no pre-load is applied to the shaft. We perform the accuracy measurements by applying the pre-load of 800gf in the backward thrust direction at our shipping inspection. Please be careful not to place more than a rated trust in a forward thrust direction at a time of installation. Note 3) The actuator cable is not designed to withstand repeated bending stress. Please contact us if the cable receives repeated bending stress. Safety Mechanism The damper system is set at the front end of stroke and limit sensor is installed at the rear end. Compatibility The mounting section of this linear actuator is compatible with manual micrometer. Special Driver Please use the driver LAD-01 series (Recommend), BSD-11 series which was specially developed for this actuator. Extension Cable The encoder is open collector type. The transmission distance may be extended by the use of LAD-01D-012 or BSD-11D-012 (good for line driver type) with an extension cable. 4

6 MALS-D23 Series NEW 10/ 15/ 25 mm 4 kgf Rated thrust 0.5 m Resolution Cost-Effective Model SF Tube Standard Type Specification Nut Flat tip Original position with tapped hole type : 1.5 mm Add -03 at the last part of model number with order when 200 mm cable length is required. Parameter Rated thrust Resolution Max speed Screw lead Unidirectional repeatable accuracy Bidirectional repeatable accuracy Bidirectional positioning accuracy Average reversal error Limit sensor Length Weight Diameter Model Flat tip : H type Spherical tip : R type Tapped hole : N type M3 with depth of 5 (Note 6) Note 1) Use the accompanying screw nut to fix the actuator to your equipment. Desired accuracy may not be obtained when the actuator housing is clenched for fixing. Note 2) The actuator shaft can receive a load in the both of forward and backward thrust directions. Use springs or something similar to apply pre-load to the shaft in either one direction at the operation. Backlash is concerned and desired accuracy may not be obtained when no pre-load is applied to the shaft. We perform the accuracy measurements by applying the pre-load of 800gf in the backward thrust direction at our shipping inspection. Note 3) The actuator cable is not designed to withstand repeated bending stress. Please contact us if the cable receives repeated bending stress. Note 4) The encoders of these models have 2 channels only and have no Z phase. Note 5) As to the original position, refer to the page of term definition. Note 6) Torque loaded on a rod of actuator need to be less than 1 Nm when installing a screw to a hole in the tip of N type. Torque of over 1 Nm may cause a deterioration of actuator s precision. Safety Mechanism The damper system is set at the front end of stroke and limit sensor is installed at the rear end. Compatibility The mounting section of this linear actuator is compatible with manual micrometer. Special Driver Please use the driver LAD-01 series (Recommend), BSD-06 series which was specially developed for this actuator. Extension Cable The encoder is open collector type. The transmission distance may be extended by the use of LAD-01D-012 or BSD-06D-012 (good for line driver type) with an extension cable. 5

7 MAS-D23 Series 10/ 15/ 25 mm 6 kgf Rated thrust 0.25 m Resolution Spherical tip Standard Type Nut Flat tip Original position Add -03 at the last part of model number with order when 200 mm cable length is required. Specification Parameter Model Rated thrust Resolution Max speed Screw lead Unidirectional repeatable accuracy Bidirectional repeatable accuracy Bidirectional positioning accuracy Average reversal error Limit sensor Length Weight Diameter Note 1) Use the accompanying screw nut to fix the actuator to your equipment. Desired accuracy may not be obtained when the actuator housing is clenched for fixing. Note 2) The actuator shaft can receive a load in the both of forward and backward thrust directions. Use springs or something similar to apply pre-load to the shaft in either one direction at the operation. Backlash is concerned and desired accuracy may not be obtained when no pre-load is applied to the shaft. We perform the accuracy measurements by applying the pre-load of 800gf in the backward thrust direction at our shipping inspection. Note 3) The actuator cable is not designed to withstand repeated bending stress. Please contact us if the cable receives repeated bending stress. Safety Mechanism The damper system is set at the front end of stroke and limit sensor is installed at the rear end. Compatibility The mounting section of this linear actuator is compatible with manual micrometer. Special Driver Please use the driver LAD-01 series (Recommend), BSD-11 series which was specially developed for this actuator. Extension Cable The encoder is open collector type. The transmission distance may be extended by the use of LAD-01D-012 or BSD-11D-012 (good for line driver type) with an extension cable. 6

8 MALB-D28 Series NEW 10/ 30 mm 5 kgf Rated thrust m Resolution with tapped hole M3 with depth of 5 Cost-Effective Model High Speed/ Long Life Type SF Tube Specification Parameter Nut Rated thrust Short time max thrust Resolution Max speed Screw lead Unidirectional repeatable accuracy Bidirectional repeatable accuracy Bidirectional positioning accuracy Average reversal error Limit sensor Length Weight Diameter 3-M3 with depth of 4 on24circumference Flat tip Original position with tapped hole type : 1.5 mm Model Add -03 at the last part of model number with order when 200 mm cable length is required. Flat tip : H type Spherical tip : R type M3 with depth of 5 Note 1) Use the accompanying screw nut to fix the actuator to your equipment. Desired accuracy may not be obtained when the actuator housing is clenched for fixing. Note 2) The actuator shaft can receive a load in the both of forward and backward thrust directions. Use springs or something similar to apply pre-load to the shaft in either one direction at the operation. Backlash is concerned and desired accuracy may not be obtained when no pre-load is applied to the shaft. We perform the accuracy measurements by applying the pre-load of 800gf in the backward thrust direction at our shipping inspection. Note 3) The actuator cable is not designed to withstand repeated bending stress. Please contact us if the cable receives repeated bending stress. Note 4) The relative position between the tapped hole for M3 set-screw and the cable is arbitrary. Note 5) The encoders of these models have 2 channels only and have no Z phase. Note 6) As to the original position, refer to the page of term definition. Tapped hole : N type 7 Safety Mechanism The damper systems are set at the both ends of stroke and limit sensor is installed at the rear end. The actuator shaft may move when a load is applied to it under the condition of no current since the actuator is unequipped with a built-in brake mechanism. Therefore, the customer may need safety measures to protect the equipment. High speed and long life High speed and long life operation is realized by the application of ball screw. Special Driver Please use the driver LAD-01 series (Recommend), BSD-06 series which was specially developed for this actuator. Extension Cable The encoder is open collector type. The transmission distance may be extended by the use of LAD-01D-012 or BSD-06D-012 (good for line driver type) with an extension cable.

9 MAB-D28 Series 10/ 30 mm 5 kgf Rated thrust 0.5 m Resolution High Speed / Long Life Type with tapped hole M3 with depth of 5 3-M3 with depth of 4 on24circumference Specification Parameter Nut Rated thrust Short time max thrust Resolution Max speed Screw lead Unidirectional repeatable accuracy Bidirectional repeatable accuracy Bidirectional positioning accuracy Average reversal error Limit sensor Length Weight Diameter Flat tip Original position with tapped hole type: 6mm Model Note 1) Use the accompanying screw nut to fix the actuator to your equipment. Desired accuracy may not be obtained when the actuator housing is clenched for fixing. Note 2) The actuator shaft can receive a load in the both of forward and backward thrust directions. Use springs or something similar to apply pre-load to the shaft in either one direction at the operation. Backlash is concerned and desired accuracy may not be obtained when no pre-load is applied to the shaft. We perform the accuracy measurements by applying the pre-load of 800gf in the backward thrust direction at our shipping inspection. Note 3) The actuator cable is not designed to withstand repeated bending stress. Please contact us if the cable receives repeated bending stress. Note 4) The relative position between the tapped hole for M3 set-screw and the cable is arbitrary. Add -03 at the last part of model number with order when 200 mm cable length is required. Flat tip : H type Spherical tip : R type Tapped hole : N type M3 with depth of 5 Safety Mechanism The damper systems are set at the both ends of stroke and limit sensor is installed at the rear end. The actuator shaft may move when a load is applied to it under the condition of no current since the actuator is unequipped with a built-in brake mechanism. Therefore, the customer may need safety measures to protect the equipment. High speed and long life High speed and long life operation is realized by the application of ball screw. Special Driver Please use the driver LAD-01 series (Recommend), BSD-11 series which was specially developed for this actuator. Extension Cable The encoder is open collector type. The transmission distance may be extended by the use of LAD-01D-012 or BSD-11D-012 (good for line driver type) with an extension cable. 8

10 Models for Special Environments MASC-D16 Series Linear Actuator for Clean Room Applicable to Clean Class 100 6/ 10/ 20 mm 1.5 kgf Rated thrust 0.25 m Resolution Spherical tip Clean SF Tube Specification Nut Flat tip Original position Add -03 at the last part of model number with order when 200 mm cable length is required. Parameter Model Rated thrust Resolution Max speed Screw lead Unidirectional repeatable accuracy Bidirectional repeatable accuracy Bidirectional positioning accuracy Average reversal error Limit sensor Length Weight Diameter Note 1) The shaft moves in the direction of the arrow when the motor rotates in CW direction. Note 2) Always use the limit switch. If not, the shaft may retrieve too deeply and never come out. Note 3) The Logic of the limit switch is normally " Close ". Please connect the limit switch to the higher rank controller and adjust the switch so as to stop the pulse output when the signal is ON. Note 4) The actuator shaft can receive a load in the both of forward and backward thrust directions. Use springs or something similar to apply pre-load to the shaft in either one direction at the operation. Backlash is concerned and desired accuracy may not be obtained when no pre-load is applied to the shaft. We perform the accuracy measurements by applying the pre-load of 800gf in the backward thrust direction at our shipping inspection. Please be careful not to place more than a rated trust in a forward thrust direction at a time of installation. Note 5) The actuator cable is not designed to withstand repeated bending stress. Please contact us if the cable receives repeated bending stress. Safety Mechanism The damper system is set at the front end of stroke and limit sensor is installed at the rear end. Compatibility The mounting section of this linear actuator is compatible with manual micrometer. Special Driver Please use the driver LAD-01 series (Recommend), BSD-11 series which was specially developed for this actuator. Extension Cable The encoder is open collector type. The transmission distance may be extended by the use of LAD-01D-012 or BSD-11D-012 (good for line driver type) with an extension cable. 9

11 Models for Special Environments MASC-D23 Series Linear Actuator for Clean Room Applicable to Clean Class / 15/ 25 mm 3 kgf Rated thrust 0.25 m Resolution Spherical tip Clean Specification Parameter Rated thrust Resolution Max speed Screw lead Unidirectional repeatable accuracy Bidirectional repeatable accuracy Bidirectional positioning accuracy Average reversal error Limit sensor Length Weight Diameter Nut Flat tip Original position Model Add -03 at the last part of model number with order when 200 mm cable length is required. Note 1) The shaft moves in the direction of the arrow when the motor rotates in CW direction. Note 2) Always use the limit switch. If not, the shaft may retrieve too deeply and never come out. Note 3) The Logic of the limit switch is normally " Close ". Please connect the limit switch to the higher rank controller and adjust the switch so as to stop the pulse output when the signal is ON. Note 4) The actuator shaft can receive a load in the both of forward and backward thrust directions. Use springs or something similar to apply pre-load to the shaft in either one direction at the operation. Backlash is concerned and desired accuracy may not be obtained when no pre-load is applied to the shaft. We perform the accuracy measurements by applying the pre-load of 800gf in the backward thrust direction at our shipping inspection. Note 5) The actuator cable is not designed to withstand repeated bending stress. Please contact us if the cable receives repeated bending stress. Safety Mechanism The damper system is set at the front end of stroke and limit sensor is installed at the rear end. Compatibility The mounting section of this linear actuator is compatible with manual micrometer. Special Driver Please use the driver LAD-01 series (Recommend), BSD-11 series which was specially developed for this actuator. Extension Cable The encoder is open collector type. The transmission distance may be extended by the use of LAD-01D-012 or BSD-11D-012 (good for line driver type) with an extension cable. 10

12 MAVB-D28 Series 10-6 Pa Specification 10/ 15/ 25 mm 2 kgf Rated thrust m Resolution Nut Flat Tip Note1 Models for Special Environments Linear Actuator for Vacuum High Vacuum Original Position Correspondence Pressure : 10-6 Pa Motor Cable Sensor Cable Positional relationship is arbitrary Limit Sensor Wire The cable ends are not fabricated. Parameter Model Rated thrust Resolution Max speed Screw lead Unidirectional repeatable accuracy Bidirectional repeatable accuracy Bidirectional positioning accuracy Average reversal error Limit sensor Sensor Allowable temperature limit Emitted Gas Speed (Note 5) Length Diameter Contact CS Touch Sensor (Normal Close) Resolver (Excitation to 1 phase Outputs from 2 phases) 1Pa Torr Wiring Color Motor Cable Note 1) The shaft moves in the direction of the arrow when the motor rotates in CW direction. Note 2) Always use the limit switch. If not, the shaft may retrieve too deeply and never come out. Note 3) The Logic of the limit switch is normally " Close ". Please connect the limit switch to the higher rank controller and adjust the switch so as to stop the pulse output when the signal is ON. Note 4) The actuator shaft can receive a load in the both of forward and backward thrust directions. Use springs or something similar to apply pre-load to the shaft in either one direction at the operation. Backlash is concerned and desired accuracy may not be obtained when no pre-load is applied to the shaft. We perform the accuracy measurements by applying the pre-load of 800gf in the backward thrust direction at our shipping inspection. Note 5) This is not guaranteed value but representative value. 1Pa Torr Resolver Cable U Phase Red V Phase Black W Phase White White Green Red Blue Black Driver Please contact us for the details about the driver. Yellow 11

13 MASG-D23 Series 10/ 15/ 25 mm 3 kgf Rated thrust 0.25 m Resolution Spherical tip Models for Special Environments Chemical Cleanliness Chemical Cleanliness Specification Nut Flat tip Original position Add -03 at the last part of model number with order when 200 mm cable length is required. Parameter Model Rated thrust Resolution Max speed Screw lead Unidirectional repeatable accuracy Bidirectional repeatable accuracy Bidirectional positioning accuracy Average reversal error Limit sensor Length Weight Diameter Note 1) The shaft moves in the direction of the arrow when the motor rotates in CW direction. Note 2) Always use the limit switch. If not, the shaft may retrieve too deeply and never come out. Note 3) The Logic of the limit switch is normally " Close ". Please connect the limit switch to the higher rank controller and adjust the switch so as to stop the pulse output when the signal is ON. Note 4) The actuator shaft can receive a load in the both of forward and backward thrust directions. Use springs or something similar to apply pre-load to the shaft in either one direction at the operation. Backlash is concerned and desired accuracy may not be obtained when no pre-load is applied to the shaft. We perform the accuracy measurements by applying the pre-load of 800gf in the backward thrust direction at our shipping inspection. Note 5) The actuator cable is not designed to withstand repeated bending stress. Please contact us if the cable receives repeated bending stress. 12

14 Cautions for Handling Products Products and other accompanying items are high precision products. All the cautions and warnings listed below should be properly understood and observed. Use the products after fully acquiring the product knowledge and confirming the safety handlings. Minimal cautions for safety use are followings. Caution at unpacking Perform visual inspection and confirm the model number when receiving the products. Cautions for handling Check the wire connection firstly. Faulty wiring shall cause malfunctions and defects. Do not pull the actuator cable and bend the root of cable. It may cause defects. Our actuator does not have ground terminals. Use the motor housing for the earth ground. Do not hit or add radial overload to the shaft. Do not add impermissible thrust overload to the shaft. It shall damage the products. Refer toactuator Fixingon P. 2 for the method. Use the screws, which are prescribed in the drawings, for driver and accompanying items. It shall damage the boards and cause malfunction, electric leakage and ignition, especially when excessively long screws are used for the driver. The life of actuator and accompanying items shall be affected by the load condition, operation mode and use environment. Fully perform the machine operation test. Do not use and store the products under the environment, which stores the materials of corrosive or poisonous gas. Avoid the intrusion of dust, droplet and oil into the products. Stop the operation and turn off the power when smoke, excess heat, abnormal smell, abnormal sound and abnormal vibration are perceived. Additional Caution Do not disassemble the products, but report it and return them when you find troubles. We perform the investigation and repair only when the products are returned properly. 13

15 Memo 14

16 LAD-01 Series Control Driver For Linear Actuator NEW LAD-01 Series LAD-01C-012 for Open Collector LAD-01D-012 for Line Driver Parameters and gains can be set by serial communication through USB cable. Outside Configuration, Install Dimension (Unit: mm) Special Features This motor driver is designed with a PWM control method to output 3 phase sine wave. This motor driver is designed for exclusive use of our ultra miniaturized linear actuators. Two types of preprogrammed gain setting can be switched by input signal. M3 Tap for a frame ground. Metal cover 4-4 hole Aluminum chassis to hold a circuit board Circuit Configuration DC/DC CONV. 24 V Power-supply to drive motor 0 V USB MINI-B USB MINI-B Connector Forward Backward USB USB Transceiver Pulse Counter I/O E2PROM Serial I/O Process to set up parameters Micro Controller /SVON /GLOW /RES /CLR /GAIN /TRQ /ORZ EMG /LSF /LSR /READY /ALM /INP IO IO Port Position command I/O Position controller Input/ output control ω cos sin i d =0 Speed controller i q cos i d i q sin Current controller v d v q Current controller d-q/ 3-phase a.c.ordinate converter 3 d-q d-q/ 3 3-phase a.c./d-q ordinate converter i v 12bit A/D i converter u v u v v v w PWM output 3 Circuit to detect current of motor Circuit to drive 3-phase motor Linear Actuator /ORGF /LSFM /LSRM EAM EBM EZM RS-422A Line Driver RS-422A Speed ω mechanical angle electric angle Speed / position signal processor Pulse Counter Encoder 15

17 Specification LAD-01 Model LAD-01 Series Input Power Supply DC 24V Continuous Rated Output Current 3 Arms Max Rated Output Current 10 A peak Control System Positioning Control Encoder Input A B Z (MALS / MALB series has no Z phase.) Hall sensor U V W (Hall IC) MAS-D16 16kHz MAB-D28 100kHz Input Max Frequency MASC-D16 MAS-D23 16kHz 20kHz MALS-D18 MALS-D23 8kHz 10kHz MASC-D23 20kHz MALB-D28 64kHz Positioning Accuracy 1 pulse of encoder resolution Multiplication function of encoder 4 multiplication function Control multiplication function 2 pulse systems: fixed 4 multiplications, others: 1 multiplication. Operating temperature 0 50 Operating humidity Below 85%RH without bedewing Storage temperature 20 to 85without bedewing Input Signals Pulse input system Selectable with parameter setting 1.2 pulse systemcw or CCW pulse system 2.1 pulse systempulse, Direction, Input 3.2-phase pulse system (Input is isolated by photo coupler) Reset input Alarm output reset, Residual pulse reset, Low active logic. Limit sensor input LSF (CW prohibition), LSR (CCW prohibition) (motor-free input) Not available G-Low input Low active is the logic of Gain Low (gain lowering due to the reduction of vibration at stoppage) Deviation clear Reset residual pulse, Low active Gain switching Switchable to 2 types of preprogrammed gain setting, Low active Start of retrieving original point Execute searching of an original point with a preprogrammed mode, Low active Output Signals INP Output In-position output can be set within a range from 0 to 15 pulse, Low active Alarm output It is output when encoder disconnection or full torque or full count or overheat occurs. (Encoder disconnection alarm is available only for a line driver type.) Cause of alarm is expressed by a number of times of flushing Encoder output A B Z Equivalent to RS-422 output Limit output Input from limit sensor is output by photo coupler Completion of searching an original point Ready Control Functions Power supply gain It is output when a search of original point is completed by a start signal to retrieve an original point. It is output when command pulse is ready to be input with the servo activated. Speed proportionate gain Speed integration gain Adjustable by parameter setting Positional gain Display Functions PWR Power ( 24V) SV Light up at the time of servo activation ALM Light up at the time of alarm occurrence. INP Residual deviation is within in-position setting point ORZ Light up when a search of original point is completed by a start signal to retrieve an original point. 16

18 BSD-11 BSD-06 Series Control Driver For Linear Actuator BSD-11 Series BSD-11C-012 for Open Collector BSD-11D-012 for Line Driver BSD-06 Series MALS / MALB for Cost-effective models, MALS/MALB Series BSD-06C-012 for Open Collector BSD-06D-012 for Line Driver Outside Configuration (Unit: mm) Special Features Driver by 3-phase sine wave PWM. Driver specially designed for our ultra compact actuator. Compact size attained by the full digital servo control where ASIC and CPU are incorporated. DC 24V single power supply. (built-in power control) Install Dimension(Unit: mm) 3-M3 Tap 2-M3 Tap Circuit Configuration Forward Backward STOP GLOW RESET ALARM INP Z A B Vref LSS LSF LSR 24V V Gate array Position command Position controller Gate array To 3-phase Transistor module Micro Controller cos sin i d =0 cos sin Speed controller i q Speed detector i d i q Current controller v d v q Current controller d-q/ 3-phase a.c.ordinate converter 3 d-q d-q3 3-phase a.c./d-q ordinate converter i v v u v v v w mechanical angle electric angle 8ch A/D 8ch i u A/D converter PWM output To 3-phase transistor module Gate array Speed / position signal processor Proportional gain(during PI control) Integration gain Positional gain Feed forward gain Proportional gain (during P control) Linear Actuator Encoder 17 MALS/MALB series has no Z phase and you do not connect the pin.

19 Specification BSD-11 BSD-06 Model BSD-11 Series BSD-06 Series Input Power Supply DC 24V Continuous Rated Output Current 1.2 Arms Changeable by adjustment of heat radiation Max Rated Output Current 2.1 Arms Control System Positioning Control Encoder Input A B Z (MALS / MALB series has no Z phase.) Hall sensor U V W (Hall IC) Input Max Frequency MAS-D16 MASC-D16 MAS-D23 MASC-D23 MAB-D28 16kHz 16kHz 20kHz 20kHz 100kHz MALS-D18 MALS-D23 MALB-D28 8kHz 10kHz 64kHz Positioning Accuracy 1 pulse of encoder resolution Multiplication function of encoder 1, 2, 4 multiplication function Control multiplication function 1, 2, 4 multiplication function ( 4 is applicable only by 2-phase input) Operating temperature 0 40 Operating humidity Below 85%RH without bedewing Storage temperature 20 to 85without bedewing Weight 250g Input Signals Pulse input system [ Chosen by jumper circuit ] 1.2 pulse systemcw or CCW pulse system 2.1 pulse systempulse, Direction, Input 3. 2-phase pulse system (Input is isolated by photocoupler) Reset input Alarm output reset, Residual pulse reset, Low active logic. Limit sensor input LSF (CW prohibition), LSR (CCW prohibition), LSS (motor free) (motor-free input) Input logic of LSF or LSR is changeable by jumper circuit G-Low input Low active is the logic of Gain Low(gain lowering due to the reduction of vibration at stoppage) Gain at gain low is re-settable by volume Output Signals INP Output In-position output, which can be set within a range from 0 to 15 pulse, Low active Alarm output Alarm for encoder disconnection or full torque or full count or fin overheat. Alarm display on LED. Logic of low active Encoder output A B Z Another 5V power to A and B is required. (MALS / MALB series has no Z phase.) Limit output Input from limit sensor is output by photocoupler Control Functions LOOP Loop Gain (adjustment for integral TC and proportional gain) P Adjustment for proportional gain POS Adjustment for position loop gain GAIN Adjustment for gain low Display Functions PWR Power ( 24V) EE Encoder disconnection: Either phase of IC Hall / Either A or B phase of Line Driver FT Full torque alarm: Max current runs longer than 1 second FC Full count alarm: Overflows of deviation counters ( counts) OH Overheat alarm: Over 75 ( 5) at heat radiate fin IP Residual deviation is within in-position setting point PL Z Deviation polarity (residual deviation : display, : no display) Z-phase 18

20 MA RoHS RoHS Directive Compliance Products Thermal contraction tube 50 Cable Actuator connection cable This cable is used for open collector type. To actuator To driver Connectors for cable are accompanied with actuator and driver so that you can make your own cable by yourself (The shapes of connectors are different from the drawing). MA-321-XXX Extension cable with line driver box Direct connection type to driver for line driver. 40 Thermal contraction tube L To driver MA L=3m 50mm MA L=5m 70mm MA L=10m 100mm MA-322-XXX Extension cable with line driver box When MA-322-XXX connector is fixed to your panel unit. This cannot be directly connected to the driver MRP-25F01 HONDA TSUSHIN KOGYO CO., LTD. 2. DF1B-24DS-2.5RC HIROSE ELECTRIC CO., LTD. 3. H4P-SHF-AA J.S.T. Mfg. Co., Ltd L Attached connector MA L=3m 50mm MA L=5m 70mm MA L=10m 100mm MA Robot cable This cable is connected directly to the open collector type driver. This cable can be used only when the actuator, whose cable length is 200mm, is selected. Thermal contraction tube To actuator Thermal contraction tube To driver 2.5mMA (03)200mm The prompt transmission of electric current and signals is guaranteed only when the total cable length is within 2.5m for Open Collector. Please add -03 (actuator cable length:200mm) at the last part of Open Collector model type with MA MA mm Robot cable This cable can be used only when the actuator, whose cable length is 200mm, is selected. Thermal contraction tube To actuator Thermal contraction tube 2.5mMA (03)200mm The prompt transmission of electric current and signals is guaranteed only when the total cable length is within 2.5m for Open Collector. Please add -03 (actuator cable length:200mm) at the last part of Open Collector model type with MA

21 Reference Drawing of Combination with Cables Open Collector Type Driver MAS / MALS MAB / MALB MASC / MASG Driver for Line Driver MA MA-321-XXX Wiring by yourself MA-322-XXX Wiring by yourself ) e.g. When Linear Actuator connector is fi xed to your panel unit. ) MA-322-XXX e.g. When MA-322-XXX connector is fi xed to your panel unit. LAD-01C-012 BSD-11C The last code of Linear Actuator LAD-01D-012 BSD-11D-012 BSD-06C-012 MA MA (Robot cable) MA (Robot cable) -03 (200mm) MA-321-XXX MA-322-XXX Wiring by yourself BSD-06D-012 Wiring by yourself MA (Robot cable) MA (Robot cable) MA-321-XXX ) e.g. When Linear Actuator connector is fi xed to your panel unit. MA (Robot cable) MA-322-XXX ) MA-322-XXX e.g. When MA-322-XXX connector is fi xed to your panel unit. Wiring by yourself MA : (03) MA : It can be used as an extension cable by connecting to -03 Actuator. 2.5m Total Cable Length: Shorter than 2.5m 12.5m Total Cable Length: Shorter than 12.5m 20

22 Term Definition L [m] 10-3 P m L [mm]p [Pulse]m Traveling range of linear actuator shaft at forward and backward movements Rated Thrust Max thrust power including pre-load amount at the max speed of linear actuator Resolution This is a minimum traveling distance per 1 pulse transmitted from the driver, which is logically attained for the position control. It is calculated by the pulse train number of encoder, multiplying rate of driver and lead length of screw. L Resolution [m] 10-3 P m L: Screw Lead (mm), P: Encoder pulse train (Pulse), m: Multiplication Pre-load Load toward the thrust (backward) direction to reduce the gaps in lead screw and ball screw of shaft. Original Position Our company defines two ways of original position settings as followings. Definition A Linear Actuator Limit Sensor ON Limit Sensor OFF Encoder Z phase Backward Forward Forward Original Position You move the shaft toward the backward direction and stop it when the alarm of limit sensor is activated. You move the shaft at 10% of max speed toward the forward direction to deactivate the alarm and stop it when the first Z phase is detected. The above point is regarded as an original position. Definition B Linear Actuator Limit Sensor ON Limit Sensor OFF Backward Forward You move the shaft toward the backward direction and stop it when the alarm of limit sensor is activated. You move the shaft at 10% of max speed toward the forward direction, and stop it when the alarm is deactivated. The above point is regarded as the original position. Original Position Definition A B Model MAS Series MAB SeriesMAR SeriesMASC SeriesMASG Series MALS SeriesMALB Series Positioning Accuracy This indicates an absolute error at the position where the shaft stops at the target position. It is synonymous with absolute accuracy including repeatable accuracy. Repeatable Accuracy This means repeatability when you perform the positioning repeatedly. Average Reversal Error This is an average difference of stop positions when you operate the positioning to the target position from the forward and backward directions. Accuracy Measurement In accordance with JIS B 6201 (Machine Tool - General Rule of Test Method), CITIZEN CHIBA PRECISION performs the accuracy measurement and defines the accuracy. Linear Actuator Number of Positioning 1 Forward Backward Original Position P0 P1 P2 P3 P4 P5 P6 P7 P8 P9 Moving Direction Accuracy Measurement As indicated in Drawing 1, we operate the positioning to the target positions from the forward and backward directions five times. By investigating the difference (deviation) of target and actual stop positions, we calculate Unidirectional Repeatable Accuracy, Bidirectional Repeatable Accuracy, Bidirectional Positioning Accuracy and Average Reversal Error. 1 The following formula calculates the distance of 1 step from P.0~8. stroke mm 2 [mm] 8 stroke mm Distance of 1 step [mm] 8 1 Step We truncate less than 100 pulses from the number of pulse trains, which is transmitted 5 5 from the amount of 1 step. The following is the amount between P8~P9; stroke (amount of 1 step 8) stroke Drawing 1 21

23 Table-1 Number Definition In accordance with the above formula in the Drawing 1 and the difference (deviation) of target and actual stop positions, we calculate Unidirectional Repeatable Accuracy, Birectional Repeatable Accuracy, Bidirectional Positioning Accuracy and Average Reversal Error. Code Positioning from Forward Direction Definitional Identity Positioning from Backward Direction 1 Number of Target Stop Position 2 j th target position Actual stop point to the target position j on i th positionings from forward or backward direction Deviation between actual and target stop positions at Pj point on i th positionings from forward or backward direction Average deviation of actual stop positions to Pj point on 5 positionings 6 Reversal error at Pj point axispositioning accuracy at Pj Positioning point accuracy of kinetic 7 8 Limit of unidirectional positioning accuracy Calculating Formula Upper Limit Lower Limit 12 Bidirectional Repeatable Accuracy (of Kinetic Axis) 13 Bidirectional Positioning Accuracy (of Kinetic Axis) Estimate of average deviation at Pj point on unidierctional positioning Calcuration from width 9 Bidirectional Positioning Accuracy 10 Bidirectional Repeatable Accuracy Average Reversal Error Maximum value ofor Unidirectional Repeatable Accuracy (of Kinetic Axis) The drawing -2 is the graph, which is calculated from /xj, Pju, Pjl, Rj of Table-1. Rj is a figure, which is calculated from 3sj+3sj+ l B l in the graph P1 4 P2 P3 P4 P5 P6 P7 P8 /xj Pju Pjl Rj 3 2 Rj max /xj Pju Pjl 1 [m] error 0 A -1 Drawing Rjmax Rjmax Accuracy Definition Unidirectional Repeatable Accuracy This indicates the repeatability, which is attained by positioning from the forward or backward direction. We define the maximum value of Rjor Rjin Table -2 as unidirectional repeatable accuracy. Bidirectional Repeatable Accuracy We define the maximum value of Rjand Rjor Rjmax in Table -2 as bidirectional repeatable accuracy Bidirectional Positioning Accuracy This is the maximum difference between the target and actual stop positions and it includes bidirectional repeatable accuracy We define A in Table-2 as bidirectional positioning accuracy. Average Reversal Error The average value of reversal error Bj Regarding the above definitions, we investigate all the products at the shipping inspection. 22

24 Semiconductor Equipment: Stepper aligner, spincoater, dicing saw, turbo molecular pump, cleaning equipment, die bonder, equipment for test, inspection and high accuracy motion control including use in vacuum condition. Optical and Magnetic Disk Storage Equipment: Optical disk initializer, optical disk testing system, optical disk storage media certifi ers. Digital Imaging Equipment: Laser scanner with mirror / polygons, high-end laser printer, image setter and other high performance spinning scanning products. Medical Equipment: High-speed dental micro grinder, ultrasonic diagnosis, artifi cial heart, X-ray instruments and centrifugal separater. Laser and Optical Equipment: Laser marker, laser scanner, optical measuring equipment, image processor, optical fi ber splicing machine, laser microscope, optical connector equipment and electron microscope. Machine Tools, FA and Inspection Equipment: Robots, actuator, cardreader, high speed drilling machine, grinding machine, mirror polishing equipment, welding machine, contact lens lathers, 3-D measuring equipment and high speed winding machine. Technical data and products are subject to change without notice. For further information, please contact us or our authorized agent at any time. / , Yoshihashi, Yachiyo, Chiba , Japan Telephone : / Facsimile : /

2

2 8 24 32C800037C800042C8000 32 40 45 54 2 3 24 40 10 11 54 4 7 54 30 26 7 9 8 5 6 7 9 8 18 7 7 7 40 10 13 12 24 22 22 8 55 8 8 8 8 1 2 3 18 11 54 54 19 24 30 69 31 40 57 23 23 22 23 22 57 8 9 30 12 12 56

More information

6 50G5S 3 34 47 56 63 http://toshibadirect.jp/room048/ 74 8 9 3 4 5 6 3446 4755 566 76373 7 37 3 8 8 3 3 74 74 79 8 30 75 0 0 4 4 0 7 63 50 50 3 3 6 3 5 4 4 47 7 48 48 48 48 7 36 48 48 3 36 37 6 3 3 37

More information

5 11 3 1....1 2. 5...4 (1)...5...6...7...17...22 (2)...70...71...72...77...82 (3)...85...86...87...92...97 (4)...101...102...103...112...117 (5)...121...122...123...125...128 1. 10 Web Web WG 5 4 5 ²

More information

6 4 45 ZS7ZS4ZS 5 59 7 8 94 05 4 5 6 4 5 5 6 8 8 40 45 48 56 60 64 66 66 68 7 78 80 8 7 8 0 0 0 90 0 0 4 4 4 4 6 57 64 69 66 66 66 69 4 0 7 48 5 4 4 5 4 4 4 7 46 46 6 46 8 46 48 46 46 4 46 46 4 4 5 4

More information

L C -6D Z3 L C -0D Z3 3 4 5 6 7 8 9 10 11 1 13 14 15 16 17 OIL CLINIC BAR 18 19 POWER TIMER SENSOR 0 3 1 3 1 POWER TIMER SENSOR 3 4 1 POWER TIMER SENSOR 5 11 00 6 7 1 3 4 5 8 9 30 1 3 31 1 3 1 011 1

More information

MIDI_IO.book

MIDI_IO.book MIDI I/O t Copyright This guide is copyrighted 2002 by Digidesign, a division of Avid Technology, Inc. (hereafter Digidesign ), with all rights reserved. Under copyright laws, this guide may not be duplicated

More information

Standard products AR Series AR Anti-rotating device built-in type Standard products AR Series AR Anti-rotating device built-in type DDAAR-G Leadmm Tra

Standard products AR Series AR Anti-rotating device built-in type Standard products AR Series AR Anti-rotating device built-in type DDAAR-G Leadmm Tra Miniature Electric cylinder AR / CL シリーズ AR / CL Series / Internal Structure AR シリンダ / AR Cylinder 実 用 新 案 取 得 / Utility model resisterd 2 Compact Cylinder with 2-phase Hollow Stepping Motor integrated

More information

2 3

2 3 * This device can only be used inside Japan in areas that are covered by subscription cable TV services. Because of differences in broadcast formats and power supply voltages, it cannot be used in overseas

More information

H8000操作編

H8000操作編 8 26 35 32H800037H800042H8000 49 55 60 72 2 3 4 48 7 72 32 28 7 8 9 5 7 9 22 43 20 8 8 8 8 73 8 13 7 7 7 55 10 49 49 13 37 49 49 49 49 49 49 12 50 11 76 8 24 26 24 24 6 1 2 3 18 42 72 72 20 26 32 80 34

More information

2 3 12 13 6 7

2 3 12 13 6 7 2 8 17 42ZH700046ZH700052ZH7000 28 43 54 63 74 89 2 3 12 13 6 7 3 4 11 21 34 63 65 8 17 4 11 4 55 12 12 10 77 56 12 43 43 13 30 43 43 43 43 10 45 14 25 9 23 74 23 19 24 43 8 26 8 9 9 4 8 30 42 82 18 43

More information

Z7000操作編_本文.indb

Z7000操作編_本文.indb 2 8 17 37Z700042Z7000 46Z7000 28 42 52 61 72 87 2 3 12 13 6 7 3 4 11 21 34 61 8 17 4 11 4 53 12 12 10 75 18 12 42 42 13 30 42 42 42 42 10 62 66 44 55 14 25 9 62 65 23 72 23 19 24 42 8 26 8 9 9 4 11 18

More information

Technische Beschreibung P82R SMD

Technische Beschreibung P82R SMD P26 halstrup-walcher GmbH http://www.krone.co.jp/ Stegener Straße 10 D-79199 Kirchzarten, Germany 124-0023 2-22-1 TEL:03-3695-5431 FAX:03-3695-5698 E-MAIL:sales-tokyo@krone.co.jp 530-0054 2-2-9F TEL:06-6361-4831

More information

*Ł\”ƒ‚ä(DCH800)

*Ł\”ƒ‚ä(DCH800) B B B B B B B B B C * This device can only be used inside Japan in areas that are covered by subscription cable TV services. Because of differences in broadcast formats and power supply voltages, it cannot

More information

32720_MR-03_JSCC_CUP

32720_MR-03_JSCC_CUP Before beginning assembly, please read these instructions thoroughly. THE FINEST RADIO CONTROL MODELS R MINI-Z Racer MR-03 Chassis Set ASF.4GHz JSCC CUP Edition Thank you for purchasing the Chassis Set

More information

FA-78F0138HDGK-8A8-RX ユーザーズ・マニュアル

FA-78F0138HDGK-8A8-RX ユーザーズ・マニュアル FA-78F0138HDGK-8A8-RX ユーザーズ マニュアル 2007.6 第 1 版 B5D 1 第 1 章 概 説 本 製 品 は FlashプログラマFL-PR5(PG-FP5 * ) 及 びFL-PR4(PG-FP4 * ) MINICUBE2に 接 続 することにより 対 象 デバイスのFlashプログラマとして 使 用 できる 変 換 アダプタです (RoHS 対 応 品 です )

More information

MOTIF XF 取扱説明書

MOTIF XF 取扱説明書 MUSIC PRODUCTION SYNTHESIZER JA 2 (7)-1 1/3 3 (7)-1 2/3 4 (7)-1 3/3 5 http://www.adobe.com/jp/products/reader/ 6 NOTE http://japan.steinberg.net/ http://japan.steinberg.net/ 7 8 9 A-1 B-1 C0 D0 E0 F0 G0

More information

SHIMPO_40P抜粋版用_H1-H4.indd

SHIMPO_40P抜粋版用_H1-H4.indd VRS VRS series For servo motor VRSSeries VRS Coaxial shaft series Features VRS series バックラッシは3 分 以 下 精 密 な 位 置 決 めに 威 力 を 発 揮 Standard backlash is 3 arc-min, ideal for precision control. 総 ころ 形 軸 受 を

More information

C FGIH C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C

C FGIH C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C TUDSR5SET TUDSR5 C 7 8 9 ch DIGITAL CS TUNER C C C C S-A C FGIH C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C

More information

Boxer 15000 DC motor 6-24V operation DC From 6V to 24V DC Selection of planetary gearboxes Up to 420rpm Front through panel mounting Bidirectional 15K

Boxer 15000 DC motor 6-24V operation DC From 6V to 24V DC Selection of planetary gearboxes Up to 420rpm Front through panel mounting Bidirectional 15K BOXER 15KS Peristaltic Pump DC, AC or Stepper Motor oem peristaltic pumps for accurate dispense of liquids. From 20オl to 700ml/min Clamshell design容asy tube change Clip-on pump head Continuous tube length

More information

2

2 8 26 38 37Z800042Z800047Z8000 54 65 72 83 101 2 3 4 7 101 53 27 33 7 8 9 5 7 9 22 47 72 8 8 8 8 102 8 13 7 7 7 65 10 67 67 13 71 40 67 67 67 67 43 67 12 55 55 11 104 8 24 26 24 20 25 6 1 2 3 18 46 101

More information

2 3 12 13 6 7

2 3 12 13 6 7 02 08 22AV55026AV550 17 25 32 22AV550 26AV550 39 50 2 3 12 13 6 7 3 4 11 8 8 9 9 8 9 23 8 9 17 4 11 4 33 12 12 11 24 18 12 10 21 39 21 4 18 18 45 45 11 5 6 7 76 39 32 12 14 18 8 1 2 32 55 1 2 32 12 54

More information

32C2100操作編ブック.indb

32C2100操作編ブック.indb 02 08 32C2100 18 24 31 37 2 3 12 13 6 7 68 67 41 42 33 34 3 4 11 8 18 4 11 4 22 13 23 11 23 12 13 14 15 10 18 19 20 20 10 9 20 18 23 22 8 8 22 9 9 4 30 10 10 11 5 13 13 16 15 26 24 37 40 39 6 7 8 1 2 29

More information

Tornado Series selection SW TiCN HSS Co FAX VL PM

Tornado Series selection SW TiCN HSS Co FAX VL PM Metal Band Saw Blades Tornado Series selection SW TiCN HSS Co FAX VL PM Selection Chart Selection Chart Solids 3 Selection Teeth 4 note 1) Structurals, Tubing H section steels Light gauge steels Tube Products

More information

137. Tenancy specific information (a) Amount of deposit paid. (insert amount of deposit paid; in the case of a joint tenancy it should be the total am

137. Tenancy specific information (a) Amount of deposit paid. (insert amount of deposit paid; in the case of a joint tenancy it should be the total am 13Fast Fair Secure PRESCRIBED INFORMATION RELATING TO TENANCY DEPOSITS* The Letting Protection Service Northern Ireland NOTE: The landlord must supply the tenant with the Prescribed Information regarding

More information

evel egarding the Transmission apability Table 1. The values given in the table are for a service factor of 1.Using the table on the right, please mod

evel egarding the Transmission apability Table 1. The values given in the table are for a service factor of 1.Using the table on the right, please mod NISSEI evel New Products evel gears atalog Number of NISSEI evel The catalog number systems of differs from other miter gears. 001 G F Hand of () Products Shape (Finished Shape) Surface finish () The haracteristics

More information

LM4663 2 Watt Stereo Class D Audio Pwr Amp w/Stereo Headphone Amplifier (jp)

LM4663 2 Watt Stereo Class D Audio Pwr Amp w/Stereo Headphone Amplifier (jp) 2 Watt Stereo Class D Audio Power Amplifier with Stereo Headphone Amplifier Literature Number: JAJS693 Boomer 2006 4 A very minor text edit (typo). (MC) Converted to nat2000 DTD. Few edits on Table 1 and

More information

combat_manual_site.ai

combat_manual_site.ai 131 71 71 71 71 71 71 71 71 71 71 71 7 1 71 71 71 71 71 71 7 1 71 71 71 71 71 71 71 71 71 71 7 1 71 7 1 71 71 71 71 71 71 71 71 71 71 71 7 www.sven.1 7 13RUS 1 71 71 71 71 71 71 71 71 71 71 7 1 71 7 1

More information

LC-24_22_19K30.indb

LC-24_22_19K30.indb L C -24K 30 L C -22K 30 L C -19K 30 http://www.sharp.co.jp/support/aquos/ 2 3 4 5 6 7 8 LC-24K30 9 10 11 12 LC-24K30 8 10 PM 11 12 9 PM 13 10 PM 14 11 15 PM 16 0 17 AM 1 3 101 103 00 00 30 50 00 00 00

More information

NKK NEWS 2012

NKK NEWS 2012 2012Spring 42 CONTROLS SINGLE POINT OF CONTROL (S.P.O.C.) Introduction / Index INDEX Module Versions: C / D BECAUSE CONTROL IS LOGIC! www.42controls.com Introduction... 2 Console Desktop Version... 3

More information

橡

橡 CO2 Laser Treatment of Tinea Pedis Masahiro UEDA:,' Kiyotaka KITAMURA** and Yukihiro GOKOH*** Table I Specifications 1. Kind of Laser 2. Wavelength of Lasers. Power of Laser. Radiation Mode. Pulse Duration.

More information

2 3

2 3 RR-XR330 C Matsushita Electric Industrial Co., Ltd.2001 2 3 4 + - 5 6 1 2 3 2 1-3 + + - 22 +- 7 22 8 9 1 2 1 2 1 2 3 12 4 1 2 5 12 1 1 2 3 1 2 1 2 10 11 1 2 $% 1 1 2 34 2 % 3 % 1 2 1 2 3 1 2 12 13 1 2

More information

1..FEM FEM 3. 4.

1..FEM FEM 3. 4. 008 stress behavior at the joint of stringer to cross beam of the steel railway bridge 1115117 1..FEM FEM 3. 4. ABSTRACT 1. BackgroundPurpose The occurrence of fatigue crack is reported in the joint of

More information

32_42H3000操作編ブック.indb

32_42H3000操作編ブック.indb 02 08 32H300037H300042H3000 19 28 40 50 60 2 3 12 13 6 7 3 4 11 44 32 46 9 9 8 8 10 29 42 19 42 42 42 22 20 41 13 16 13 11 52 12 13 42 42 14 47 8 4 11 27 26 4 42 24 26 10 9 19 26 4 11 10 44 29 42 42 13

More information

Nano Range Specification Stable & Stable Telescopic Resonators Model Nano S Nano S Nano S Nano S Nano L Nano L Nano L Nano L Nano L Nano L Nano L 130-

Nano Range Specification Stable & Stable Telescopic Resonators Model Nano S Nano S Nano S Nano S Nano L Nano L Nano L Nano L Nano L Nano L Nano L 130- L i t r o n T o t a l L a s e r C a p a b i l i t y Nano Series Ultra Compact Pulsed Nd:YAG Lasers Product Range Specification Nano Range Specification Stable & Stable Telescopic Resonators Model Nano

More information

02 08 32C700037C700042C7000 17 25 32 39 50 2 3 12 13 6 7 3 4 11 8 8 9 9 8 9 23 8 9 17 4 11 4 33 12 12 11 24 18 12 10 21 39 21 4 11 18 45 5 6 7 76 39 32 12 14 18 8 1 2 31 55 1 2 31 12 54 54 9 1 2 1 2 10

More information

ZV500操作編_本文.indb

ZV500操作編_本文.indb 2 8 17 37ZV50042ZV500 28 42 52 61 72 87 2 3 12 13 6 7 3 4 11 21 34 61 8 17 4 11 4 53 12 12 10 75 18 12 42 42 13 30 42 42 42 42 10 44 55 14 25 9 62 65 23 72 23 19 24 42 8 26 8 9 9 4 11 10 18 41 80 5 6 7

More information

J. Jpn. Inst. Light Met. 65(6): 224-228 (2015)

J. Jpn. Inst. Light Met. 65(6): 224-228 (2015) 65 62015 224 228 ** Journal of The Japan Institute of Light Metals, Vol. 65, No. 6 (2015), 224 228 2015 The Japan Institute of Light Metals Investigation of heat flow behavior on die-casting core pin with

More information

™…

™… Review The Secret to Healthy Long Life Decrease in Oxidative and Mental Stress My motto is Health is not all. But nothing can be done without health. Health is the most important requisite for all human

More information

Unidirectional Measurement Current-Shunt Monitor with Dual Comparators (Rev. B

Unidirectional Measurement Current-Shunt Monitor with Dual Comparators (Rev. B www.tij.co.jp INA206 INA207 INA208 INA206-INA208 INA206-INA208 V S 1 14 V IN+ V S 1 10 V IN+ OUT CMP1 IN /0.6V REF 2 3 1.2V REF 13 12 V IN 1.2V REF OUT OUT CMP1 IN+ 2 3 9 8 V IN CMP1 OUT CMP1 IN+ 4 11

More information

Fig. 4. Configuration of fatigue test specimen. Table I. Mechanical property of test materials. Table II. Full scale fatigue test conditions and test

Fig. 4. Configuration of fatigue test specimen. Table I. Mechanical property of test materials. Table II. Full scale fatigue test conditions and test (J. Soc. Mat. Sci., Japan), Vol. 52, No. 11, pp. 1351-1356, Nov. 2003 Fatigue Life Prediction of Coiled Tubing by Takanori KATO*, Miyuki YAMAMOTO*, Isao SAWAGUCHI** and Tetsuo YONEZAWA*** Coiled tubings,

More information

MKS-05 "TERRA-Pプラス 日本語訳取扱説明書

MKS-05 TERRA-Pプラス 日本語訳取扱説明書 MKS-05 "TERRA-P+" BICT.412129.021 KE Sparing-Vist Center Sparing-Vist Center ECOTEST (+38 032) 242-15-15 (+38 032) 242-20-15 sales@ecotest.ua 18 ( ) 2 1. 3 2. 3 3. 4 4. 4 5. 6 6. 7 7. 11 8. 11 9. 11 10.

More information

323742RH500操作編.indb

323742RH500操作編.indb 02 08 18 32RH50037RH50042RH500 28 43 49 60 56 69 2 3 12 13 6 7 3 4 11 22 34 20 9 9 8 8 30 43 43 43 30 43 XX 45 15 50 12 12 11 27 40 12 43 43 13 8 4 11 27 4 26 56 24 24 9 24 17 26 4 10 10 XX 19 42 64 30

More information

LM117/LM317A/LM317 可変型3 端子レギュレータ

LM117/LM317A/LM317 可変型3 端子レギュレータ LM117,LM317 LM117/LM317A/LM317 3-Terminal Adjustable Regulator Literature Number: JAJSBC1 LM317A/LM317 3 3 LM317A 3 LM317 1.2 37V 1.5A 3 IC 2 / IC AC IC 6 3 LM317 3-Terminal Adjustable Regulator LM117

More information

elemmay09.pub

elemmay09.pub Elementary Activity Bank Activity Bank Activity Bank Activity Bank Activity Bank Activity Bank Activity Bank Activity Bank Activity Bank Activity Bank Activity Bank Activity Bank Number Challenge Time:

More information

Motivation and Purpose There is no definition about whether seatbelt anchorage should be fixed or not. We tested the same test conditions except for t

Motivation and Purpose There is no definition about whether seatbelt anchorage should be fixed or not. We tested the same test conditions except for t Review of Seatbelt Anchorage and Dimensions of Test Bench Seat Cushion JASIC Motivation and Purpose There is no definition about whether seatbelt anchorage should be fixed or not. We tested the same test

More information

388599-P036-P041

388599-P036-P041 Die life improvement of flat type punches for hot forging Morihiko Nakasaki, Koji Era, Hiroyuki Myochin and Ichiro Takasu Synopsis: Since forged products have been required more complex and net-shape,

More information

L3 Japanese (90570) 2008

L3 Japanese (90570) 2008 90570-CDT-08-L3Japanese page 1 of 15 NCEA LEVEL 3: Japanese CD TRANSCRIPT 2008 90570: Listen to and understand complex spoken Japanese in less familiar contexts New Zealand Qualifications Authority: NCEA

More information

NSR-500 Create USB Installer Procedures

NSR-500 Create USB Installer Procedures Creating NSR-500 USB Installer Overview This document describes how to create the USB installer for the NSR- 500 series. Applicable Model NSR-500 Series To Be Required * Windows (XP, Vista or 7) installed

More information

untitled

untitled SURVEY PROGRAMME For Special Survey No. / Intermediate Survey that is scheduled from to for the ship as stated below: : : SHIP S NAME : CLASS ID : : CLASS NOTATION: : : PORT OF REGISTRY: FLAG : / : OFFICIAL

More information

Vol. A-TAP A-SFT A-POT Highly Efficient Multi-Purpose Tap Series Galling No Galling Galling No Galling Spiral Fluted Tap NEXT NEW SIZES FROM NEXT Spiral Fluted Tap FROM P.18 P.20 NEXT NEW SIZES FROM

More information

Diskette Drive Installation

Diskette Drive Installation Diskette Drive Installation HP Workstation xw Series This document describes how to install a diskette drive. Kit Contents This product is shipped with the necessary supplies for installing a diskette

More information

目 次 : ページ 使 用 目 的 4 安 全 上 のご 注 意 4 重 要 なご 注 意 4 機 能 4 接 続 4 各 種 フィードバックコンタクトの 接 続 例 6 2

目 次 : ページ 使 用 目 的 4 安 全 上 のご 注 意 4 重 要 なご 注 意 4 機 能 4 接 続 4 各 種 フィードバックコンタクトの 接 続 例 6 2 フィードバックモジュール 60881 目 次 : ページ 使 用 目 的 4 安 全 上 のご 注 意 4 重 要 なご 注 意 4 機 能 4 接 続 4 各 種 フィードバックコンタクトの 接 続 例 6 2 Using the Product as Intended 8 Safety Notes 8 Important Notes 8 Functions 8 Connect 8 Sample

More information

Diskette Drive Installation

Diskette Drive Installation Diskette Drive Installation HP xw Series Workstation This document describes how to install a diskette drive. Kit Contents This product is shipped with the necessary supplies for installing a diskette

More information

Anti-Vibration AD Bar for Internal Machining AD Feature for maximum 6 times of L/D with the advanced damper effect. By anti vibration damper effect, i

Anti-Vibration AD Bar for Internal Machining AD Feature for maximum 6 times of L/D with the advanced damper effect. By anti vibration damper effect, i 内径 Boring ADバー AD Bar ADバー 防振機構内蔵ヘッド交換式ボーリングバー Anti-Vibration AD Bar ヘビーメタル製特殊ダンパー機構で ビビリ や 振動 を抑制 Suppressed chattering with the anti-vibration dampener ヘッド交換で 多様な加工に対応 A wide variety of internal machining

More information

1

1 PalmGauss SC PGSC-5G Instruction Manual PalmGauss SC PGSC-5G Version 1.01 PalmGauss SC PGSC5G 1.... 3 2.... 3 3.... 3 3.1... 3 3.2... 3 3.3 PalmGauss... 4 3.4... 4 3.4.1 (Fig. 4)... 4 3.4.2 (Fig. 5)...

More information

Removable doors Removable type Size Shelves Weight Order a total of 8 shelves per cabinet Shelf Part No.TD50 60kg/shelf Removable Tool Storage Cabinet

Removable doors Removable type Size Shelves Weight Order a total of 8 shelves per cabinet Shelf Part No.TD50 60kg/shelf Removable Tool Storage Cabinet STORAGE CABINET TOOL STORAGE CABINET TOOL REMOVABLE 265 Removable doors Removable type Size Shelves Weight Order a total of 8 shelves per cabinet Shelf Part No.TD50 60kg/shelf Removable Tool Storage Cabinet

More information

C C C - J TH-D TH-D TH-D C C C C C - J TH-D TH-D TH-D C - J TH-D TH-D TH-D C C C C

C C C - J TH-D TH-D TH-D C C C C C - J TH-D TH-D TH-D C - J TH-D TH-D TH-D C C C C C Matsushita Electric Industrial Co., Ltd. - J TH-D TH-D TH-D C C C C - J TH-D TH-D TH-D C C C C C - J TH-D TH-D TH-D C - J TH-D TH-D TH-D C C C C - J FGIH FGIH FG IH FGIH F G FGIH - J c c c c c c C C

More information

DL1720/DL1740ディジタルオシロスコープユーザーズマニュアル

DL1720/DL1740ディジタルオシロスコープユーザーズマニュアル DL1720/DL1740 IM 701710-01 http://www.yokogawa.co.jp/measurement/ 0120-137046 tmi-cs@csv.yokogawa.co.jp FAX 0422-52-6624 Disk No. DL30 2nd Edition : July 2001 (YK) All Rights Reserved, Copyright 2001 Yokogawa

More information

**編集*

**編集* $ NTN constant velocity joint for automobiles supports the concept of "Fun to Drive" NTN constant velocity joints are used in automotive propeller shafts and half shafts to transmit power from the engine

More information

Triple 2:1 High-Speed Video Multiplexer (Rev. C

Triple 2:1 High-Speed Video Multiplexer (Rev. C www.tij.co.jp OPA3875 µ ± +5V µ RGB Channel OPA3875 OPA3875 (Patented) RGB Out SELECT ENABLE RED OUT GREEN OUT BLUE OUT 1 R G B RGB Channel 1 R1 G1 B1 X 1 Off Off Off 5V Channel Select EN OPA875 OPA4872

More information

Microsoft Word - Meta70_Preferences.doc

Microsoft Word - Meta70_Preferences.doc Image Windows Preferences Edit, Preferences MetaMorph, MetaVue Image Windows Preferences Edit, Preferences Image Windows Preferences 1. Windows Image Placement: Acquire Overlay at Top Left Corner: 1 Acquire

More information

NotePC 8 10cd=m 2 965cd=m 2 1.2 Note-PC Weber L,M,S { i {

NotePC 8 10cd=m 2 965cd=m 2 1.2 Note-PC Weber L,M,S { i { 12 The eect of a surrounding light to color discrimination 1010425 2001 2 5 NotePC 8 10cd=m 2 965cd=m 2 1.2 Note-PC Weber L,M,S { i { Abstract The eect of a surrounding light to color discrimination Ynka

More information

(1 ) (2 ) Table 1. Details of each bar group sheared simultaneously (major shearing unit). 208

(1 ) (2 ) Table 1. Details of each bar group sheared simultaneously (major shearing unit). 208 2463 UDC 621.771.251.09 : 621.791.94: 669.012.5 Improvement in Cold Shear Yield of Bar Mill by Computer Control System Koji INAZAKI, Takashi WASEDA, Michiaki TAKAHASHI, and Toshihiro OKA Synopsis: The

More information

C 04 D 10 D 11 D 12 D A 14 D 16 D 17 D 18 D 19 D 419 29 D A A A 33 D 2933 2028 3445 20 D A 21 D 22 D 23 D 23 D 24 D 27 D 34 D 35 D 36 D 38 D A A 40 D

C 04 D 10 D 11 D 12 D A 14 D 16 D 17 D 18 D 19 D 419 29 D A A A 33 D 2933 2028 3445 20 D A 21 D 22 D 23 D 23 D 24 D 27 D 34 D 35 D 36 D 38 D A A 40 D C C D D D D D D C Matsushita Electric Industrial Co., Ltd.All Rights Reserved. C 04 D 10 D 11 D 12 D A 14 D 16 D 17 D 18 D 19 D 419 29 D A A A 33 D 2933 2028 3445 20 D A 21 D 22 D 23 D 23 D 24 D 27 D 34

More information

Z3500操作編ブック.indb

Z3500操作編ブック.indb 02 08 18 37Z350042Z350046Z3500 52Z350057Z3500 28 40 57 68 82 2 3 12 13 6 7 3 4 11 21 19 57 9 9 8 8 10 42 42 42 42 42 18 16 23 41 13 16 13 11 70 12 13 42 42 14 45 8 4 11 27 26 4 25 10 9 24 23 18 26 4 10

More information

特-3.indd

特-3.indd Development of Automation Technology for Precision Finishing Works Employing a Robot Arm There is demand for the automation of finishing processes that require technical skills in the manufacturing of

More information

PA M01 LITEON SPEC Rev A

PA M01 LITEON  SPEC Rev A 規格書 Electrical Specification Model No: PA-1360-5M01 Description: 12V 36W single output AC adapter Revision: A Issued Date: May 21, 2013 Customer Part No.: 90, Chien I Rd, Chung Ho city, Taipei Hsien 235,

More information

137ヌ6 7ヌ7 7ヌ7 7ヌ8 7ヌ8 7ヌ8 2 LightSYS Quick Engineer Guide

137ヌ6 7ヌ7 7ヌ7 7ヌ8 7ヌ8 7ヌ8 2 LightSYS Quick Engineer Guide 13Quick Installation Guide LightSYS Ver 2.xx For detailed information please refer to the full LightSYS Engineer Manual provided on our website: www.riscogroup.com 137ヌ6 7ヌ7 7ヌ7 7ヌ8 7ヌ8 7ヌ8 2 LightSYS

More information

エイブル 減 速 機 は 豊 富 なバリエーションでお 客 様 の 要 望 にお 応 え Nidec Shimpo has a lineup with a lot of product variation; Able reducers 同 芯 軸 タイプ ABLE Reducer 静 音 高 精 度

エイブル 減 速 機 は 豊 富 なバリエーションでお 客 様 の 要 望 にお 応 え Nidec Shimpo has a lineup with a lot of product variation; Able reducers 同 芯 軸 タイプ ABLE Reducer 静 音 高 精 度 Coaxial shaft type VRS VRS series VRT VRT series VRSF VRSF series VRG VRG series エイブル 減 速 機 は 豊 富 なバリエーションでお 客 様 の 要 望 にお 応 え Nidec Shimpo has a lineup with a lot of product variation; Able reducers 同

More information

1. Database&Logic 2. 3. Word/Excel/PPT/PDF&Web Ultimate Dictionary 4. Jukkou&Rewrite 5. Convenience&Safety 6. Chinese&Korean 7. Support&Consultation 8

1. Database&Logic 2. 3. Word/Excel/PPT/PDF&Web Ultimate Dictionary 4. Jukkou&Rewrite 5. Convenience&Safety 6. Chinese&Korean 7. Support&Consultation 8 www.jukkou.com 1. Database&Logic 2. 3. Word/Excel/PPT/PDF&Web Ultimate Dictionary 4. Jukkou&Rewrite 5. Convenience&Safety 6. Chinese&Korean 7. Support&Consultation 8. Jukkou Z 9. Introduction Example 10.

More information

10 2000 11 11 48 ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) CU-SeeMe NetMeeting Phoenix mini SeeMe Integrated Services Digital Network 64kbps 16kbps 128kbps 384kbps

More information

The Japanese economy in FY2015 suffered from sluggish growth in individual consumption, while the foreign exchange market remained unstable with high volatility. Even in such an economic environment, MSF

More information

NSR-500 Installation Guide

NSR-500 Installation Guide NSR Installation Guide This information has been prepared for the professional installers not for the end users. Please handle the information with care. Overview This document describes HDD installation

More information

FCC This product is conform to the FCC standards. FCC Rules (Federal Communications Commission) This product complies with Part15 Subpart B and C of the FCC Rules. FCC ID : MK4TR3XM-SX01 FCC NOTICE This

More information

Fig. 1. Relation between magnetron anode current and anode-cathod voltage. Fig. 2. Inverter circuit for driving a magnetron. 448 T. IEE Japan, Vol. 11

Fig. 1. Relation between magnetron anode current and anode-cathod voltage. Fig. 2. Inverter circuit for driving a magnetron. 448 T. IEE Japan, Vol. 11 High Frequency Inverter for Microwave Oven Norikazu Tokunaga, Member, Yasuo Matsuda, Member, Kunio Isiyama, Non-member (Hitachi, Ltd.), Hisao Amano, Member (Hitachi Engineering, Co., Ltd.). Recently resonant

More information

1 138

1 138 5 1 2 3 4 5 6 7 8 1 138 BIOS Setup Utility MainAdvancedSecurityPowerExit Setup Warning Item Specific Help Setting items on this menu to incorrect values may cause your system to malfunction. Select 'Yes'

More information

Tetsu-to-Hagane Vol. 87 (2001) No. 5 Table 1. Physical properties of particles. (a) side view (b) front view Fig. 1. Experimental apparatus with semic

Tetsu-to-Hagane Vol. 87 (2001) No. 5 Table 1. Physical properties of particles. (a) side view (b) front view Fig. 1. Experimental apparatus with semic Tetsu-to-Hagane Vol. 87 (2001) No. 5 Deadman.Renewal Motion in a Cold Model of Blast Furnace Hiroshi TAKAHASHI and Hideki KAWAI Synopsis : Permeability in coke bed in the lower part of blast furnace is

More information

i5 Catalyst Case Instructions JP

i5 Catalyst Case Instructions JP Catalyst iphone iphone iphone ON/OFF O O Touch ID Page 01 iphone O O O O O Page 02 ( ) O OK O O O 30 30 min Page 03 ( ) 30 O iphone iphone iphone iphone iphone iphoneiphone Catalyst ON/OFF iphone iphone

More information

IM 21B04C50-01

IM 21B04C50-01 User s Manual Blank Page Media No. (CD) 5th Edition : Sep. 2009 (YK) All Rights Reserved. Copyright 2001, Yokogawa Electric Corporation Yokogawa Electric Corporation Software License Agreement This

More information

パナソニック技報

パナソニック技報 Panasonic Technical Journal Vol. 59 No. 2 Nov. 2013 Environmental Resistance Technology of Outdoor Surveillance Camera Takaya Kamimura Izumi Satou Jouji Wada Tamotsu Uchida Yuuya Jikihara Hideki Yasuda

More information

Author Workshop 20111124 Henry Cavendish 1731-1810 Biot-Savart 26 (1) (2) (3) (4) (5) (6) Priority Proceeding Impact factor Full paper impact factor Peter Drucker 1890-1971 1903-1989 Title) Abstract

More information

189 2015 1 80

189 2015 1 80 189 2015 1 A Design and Implementation of the Digital Annotation Basis on an Image Resource for a Touch Operation TSUDA Mitsuhiro 79 189 2015 1 80 81 189 2015 1 82 83 189 2015 1 84 85 189 2015 1 86 87

More information

ユーザーズマニュアル

ユーザーズマニュアル 1 2 3 4 This product (including software) is designed under Japanese domestic specifications and does not conform to overseas standards. NEC *1 will not be held responsible for any consequences resulting

More information

123-099_Y05…X…`…‘…“†[…h…•

123-099_Y05…X…`…‘…“†[…h…• 1. 2 1993 2001 2 1 2 1 2 1 99 2009. 1982 250 251 1991 112 115 1988 75 2004 132 2006 73 3 100 3 4 1. 2. 3. 4. 5. 6.. 3.1 1991 2002 2004 3 4 101 2009 3 4 4 5 1 5 6 1 102 5 6 3.2 2 7 8 2 X Y Z Z X 103 2009

More information

What s GLAS LUCE Flat / Minimum / Stylish / Surprise Interior / Public / Information and more! POSSIBILITIES Multi-display Kitchen back panel Powder r

What s GLAS LUCE Flat / Minimum / Stylish / Surprise Interior / Public / Information and more! POSSIBILITIES Multi-display Kitchen back panel Powder r Stylish & Elegant LCD GLASS Technorogy System interior Oct. 2015 Ver.04 In our contemporary society, many information are sent from a display monitor as pictures,sound and light, which is indispensable

More information

394-04

394-04 Change and Development of Continuous Casting Technology Abstract It is about 60 years that history of continuous casting process in our country. From the start of commercial operation of the first continuous

More information

国際恋愛で避けるべき7つの失敗と解決策

国際恋愛で避けるべき7つの失敗と解決策 7 http://lovecoachirene.com 1 7! 7! 1 NOT KNOWING WHAT YOU WANT 2 BEING A SUBMISSIVE WOMAN 3 NOT ALLOWING THE MAN TO BE YOUR HERO 4 WAITING FOR HIM TO LEAD 5 NOT SPEAKING YOUR MIND 6 PUTTING HIM ON A PEDESTAL

More information

202

202 201 Presenteeism 202 203 204 Table 1. Name Elements of Work Productivity Targeted Populations Measurement items of Presenteeism (Number of Items) Reliability Validity α α 205 α ä 206 Table 2. Factors of

More information

LEGACY 1. LEGACY A: DIMENSION 1. SEDAN MODEL 2.5 L SOHC 2.5 L DOHC turbo Overall length mm (in) 4,730 (186.2) Overall width mm (in) 1,730 (68.1) Overa

LEGACY 1. LEGACY A: DIMENSION 1. SEDAN MODEL 2.5 L SOHC 2.5 L DOHC turbo Overall length mm (in) 4,730 (186.2) Overall width mm (in) 1,730 (68.1) Overa LEGACY 1. LEGACY A: DIMENSION 1. SEDAN MODEL 2.5 L SOHC 2.5 L DOHC turbo Overall length mm (in) 4,730 (186.2) Overall width mm (in) 1,730 (68.1) Overall height (at C.W.) mm (in) 1,425 (56.1), 1,435 (56.5)

More information

\615L\625\761\621\745\615\750\617\743\623\6075\614\616\615\606.PS

\615L\625\761\621\745\615\750\617\743\623\6075\614\616\615\606.PS osakikamijima HIGH SCHOOL REPORT Hello everyone! I hope you are enjoying spring and all of the fun activities that come with warmer weather! Similar to Judy, my time here on Osakikamijima is

More information

1

1 05FEB2013 Rev. B LCD COAXIAL EMBEDDED DISPLAY INTERFACE(LCEDI)CONNECTOR 1. 目 的 LCD COAXIAL EMBEDDED DISPLAY INTERFACE (LCEDI) CONNECTOR において ケーブルのはんだ 付 け 手 順 及 びUPPER SHELL, PULL BAR の 組 み 付 けについて 明 記

More information

Fig. 1. Active faults in the Kanto district (after Coordinating Committee for Earthquake Prediction, 1980). A-A' PROFILE DOUGUER ANOMALY RESIDUAL ANOM

Fig. 1. Active faults in the Kanto district (after Coordinating Committee for Earthquake Prediction, 1980). A-A' PROFILE DOUGUER ANOMALY RESIDUAL ANOM Structure of the Basement and the Gravity Anomaly in the Kanto Plain -A Geophysical Study of Active Fault- Takashi TADA Crustal Dynamics Department, Geographical Survey Institute (Received Apirl 7, 1983)

More information

Table 1. Main specifications of VAD plant. Fig. 2. Typical operating pattern of low alloy steel.

Table 1. Main specifications of VAD plant. Fig. 2. Typical operating pattern of low alloy steel. UDC 669. 184. 244. 66-251: 669. 046. 554-982 On the Operations of LD-VAD Process and Product Qualities Takaharu MORIYA and Masanori TAWARA Synopsis: VAD (Vacuum Arc Degassing) plant is characterized by

More information

Jan THE JAPANESE JOURNAL OF ANTIBIOTICS XL-1 Table 1. Outline of administering doses, routes and sampling times *: 4 ml/hr/kg Bacillus subtilis

Jan THE JAPANESE JOURNAL OF ANTIBIOTICS XL-1 Table 1. Outline of administering doses, routes and sampling times *: 4 ml/hr/kg Bacillus subtilis THE JAPANESE JOURNAL OF ANTIBIOTICS XL-1 Jan. 1987 Jan. 1987 THE JAPANESE JOURNAL OF ANTIBIOTICS XL-1 Table 1. Outline of administering doses, routes and sampling times *: 4 ml/hr/kg Bacillus subtilis

More information

DPA,, ShareLog 3) 4) 2.2 Strino Strino STRain-based user Interface with tacticle of elastic Natural ObjectsStrino 1 Strino ) PC Log-Log (2007 6)

DPA,, ShareLog 3) 4) 2.2 Strino Strino STRain-based user Interface with tacticle of elastic Natural ObjectsStrino 1 Strino ) PC Log-Log (2007 6) 1 2 1 3 Experimental Evaluation of Convenient Strain Measurement Using a Magnet for Digital Public Art Junghyun Kim, 1 Makoto Iida, 2 Takeshi Naemura 1 and Hiroyuki Ota 3 We present a basic technology

More information

Clustering in Time and Periodicity of Strong Earthquakes in Tokyo Masami OKADA Kobe Marine Observatory (Received on March 30, 1977) The clustering in time and periodicity of earthquake occurrence are investigated

More information

memo 1 2 H L N Y N

memo 1 2 H L N Y N C-3 3B21 BSB3B21-A1302 memo 1 2 H L N Y N JJY 1000km 1000km B 20066 NICT 0120612911 1 2 3 3 4 1 1 1 1 5 UTC DST UTC UTC JSTUTC DST UTCJST 1 2 3 4 1 2 3 4 WATER RESISTANT 10BAR 7N01-0B40 R2 AG WATER RESISTANT

More information

Table 1. Assumed performance of a water electrol ysis plant. Fig. 1. Structure of a proposed power generation system utilizing waste heat from factori

Table 1. Assumed performance of a water electrol ysis plant. Fig. 1. Structure of a proposed power generation system utilizing waste heat from factori Proposal and Characteristics Evaluation of a Power Generation System Utilizing Waste Heat from Factories for Load Leveling Pyong Sik Pak, Member, Takashi Arima, Non-member (Osaka University) In this paper,

More information

TM-m30 詳細取扱説明書

TM-m30 詳細取扱説明書 M00094101 Rev. B Seiko Epson Corporation 2015-2016. All rights reserved. 2 3 4 5 6 7 8 Bluetooth 9 Bluetooth 10 1 11 Bluetooth 12 1 13 1 2 6 5 4 3 7 14 1 1 2 3 4 5 15 16 ONF 1 N O O N O N N N O F N N F

More information

This paper is going to take up the "Cultural history of dishes" as a part of the "Ancient pulley and the Korean people series II". In the ancient times the pulley was used to make basically dishes for

More information