Kyosho Super Ten GP FW-04 Manual

Transcription

1 INSTRUCTION MANUAL Before commencing assembly, please read these instructions thoroughly! R THE FINEST RADIO CONTROL MODELS Size GP WD Radio Controlled.5 Engine Powered Touring Car Series SuperTen GP FW-0 WD D AMG Mercedes CLK INDEX REQUIRED FOR OPERATION RADIO PREPARATION BEFORE YOU BEGIN 5 ARRANGEMENT OF PLASTIC PARTS ON RUNNERS 5 6 ASSEMBLY ADJUSTMENT OPERATING YOUR MODEL SAFELY 8 SPARE PARTS & OPTIONAL 3 PARTS EXPLODED VIEW 3 33 SAFETY PRECAUTIONS This radio control model is not a toy. 000 KYOSHO First-time builders should seek the advice of experienced modellers before commencing assembly and if they do not fully understand any part of the construction. Assemble this kit only in places out of children's reach! Take care before operating this model. You are responsible for this model's assembly and safe operation! Always keep this instruction manual ready at hand for quick reference, even after completing the assembly. SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE. No. 300

2 R REQUIRED FOR OPERATION () Minimum channel radio with servos, and battery box. Battery Box If already included with the CAUTION: Only use a surface radio with channels and servos! radio, no battery box needs to be pur-chased separately. Stick-type AA-size Batteries ch radio. AA AA AA Because there are stick-type and wheel-type transmitters, use which ever fits your convenience best. Switch the reverse (transmitter) for the steer-ing and throttle control. For more information on the radio, refer to its instruction manual. Wheel-type ch radio. Suitable servos & receiver Servo Receiver CAUTION: If servos are not able to install, eaven this size. Need to modify upper deck. Required for engine starting: Glow Fuel & Fuel Pump Booster Cord Plug Wrench Engines for R/C models require glow fuel. Be careful not to purchase gasoline or kerosene by mistake; both cannot be used! Also, be very careful when han-- dling glow fuel which is hi-ghly inflamma-- ble and high-explosive! Besides glow fuel, engines also require engine starting equipment. This comprises a glow plug heater (booster cord & batteries) and a plug wrench for removing and installing the glow plug. HANDY FUEL WARNING: Gasoline or kerosene cannot No.7330 be used. 3 Paint and Brush PAINT BRUSH For painting the body, use Kyosho paints for models! No.30 POLYCA COLOR No KYOSHO SPRAY COLOR CAUTION: Before using spray colors, always read their explanations! KY OSH O S PR AY CO LO R No.8 (mm x 5m) 8 (.5mm x 5m) 83 (.5mm x 5m) 85 (0.mm x 8m) 860 (0.7mm x 8m) Micron Line Tape KYOSHO No No.7 D- D FLEX COLOR DECAL MASKING SHEET MICRON LINE TAPE Self-adhesive super-flexible sheets that Super-flexible tape for masking and detail designing bond to polycarbonate - even when For safe masking jobs, use this plastic masking jobs. applied to curved surfaces. sheet featuring one self-adhesive edge.

3 REQUIRED FOR OPERATION () Tools required TOOLS INCLUDED Phillips Screw Driver (L.M.S) Hex Wrench (.5mm, mm,.5mm, 5mm) Needle Nose Pliers CAUTION: Handle tools carefully! Sharp Hobby Knife Cross Wrench Wire Cutters Awl Instant Glue Rubber Cement Grease GREASE No.0 LOCTITE Midium Strength ROUND CUTTER & SANDER No.8 SPECIAL TAPER REAMER No.803 To prevent the screws For trimming bodies. Cutting along curved No need to pre-drill! from becoming loose. lines never was so easy! Drills neat mm to 5mm holes directly! RADIO PREPARATION 3 Set up the radio control system as indicated below. 8 ON 0 OFF ON OFF Transmitter Insert AA-size dry batteries. (Transmitter) Extend the antenna. (Transmitter) 3 Insert AA-size dry batteries. (Battery Box) Connect the battery box. 5 Extend the antenna. (Receiver) 6 Center the trims. 7 Switch on the transmitter. 8 Switch on the receiver. Make sure the servos move according to your transmitter inputs. Servo START FINISH Switch off the receiver. Retract the antenna. (Transmitter) 0 Switch Receiver Switch off the transmitter. 5 3

4 BEFORE YOU BEGIN () Read through the manual before you begin, so you will have an overall idea of what to do. Check all parts. If you find any defective or missing parts, contact your local dealer or our Kyosho Distributor. 3 How to read the instruction manual: No., No.5, No.6 Front Suspension 5 x 0mm Metal Bushing This instruction manual uses several symbols. Please note them during the entire assembly. 5 5 King Pin mm Pillow Ball (Black) 6 R 7 L 5 8 Key Number, Part Name, True-to-scale Diagram, Quantity Used All parts except screws are identified by key numbers. For purchasing spare parts, find the key no. of the part needed in the spare part list and refer to the left column to look up the corresponding order no. Symbols used throughout the instruction manual, comprise: Part bags used. mm Drill holes with the specified diameter (here: mm). True-to-scale diagram. Apply instant glue (CA glue, super glue). Cut off shaded portion. Must be purchased separately! Apply grease. Cut off excess. Pay close attention here! x No.0 Apply rubber cement. Tentatively tighten. Ball bearings are optional! 0 (with optional part no.) Assemble as many times as Ensure smooth non-binding specified (here: twice). movement while assembling. Assemble left and right sides Assemble in the specified the same way. order.

5 BEFORE YOU BEGIN () 5 This kit contains screws and hardware in different metric sizes and shapes. Before using them, check the screws on the true-to-scale diagrams on the left side in each assembly step. Some screws are extras. SCREWS OTHER HARDWARE Screw Self-tapping (TP) Screw Screw Washer Nut E-ring Cap Screw TP F/H Screw mm Flat Head (F/H) Screw Set Screw F/H Screw Metal Bushing Bearing 5mm Pillow Ball mm 0mm 6.8mm 6 Correct Self-tapping (TP) screws cut threads into the parts when being tightened. Excessive force may Wrong permanently damage parts when tightening TP screws. It is recommended to stop tightening when the part is attached or when some resistance is felt after the threaded portion enters the plastic. Overtightened. The threads are stripped. ARRANGEMENT OF PLASTIC PARTS ON RUNNERS No S F H No No Shaded Parts are not used. 53 5

6 ARRANGEMENT OF PLASTIC PARTS ON RUNNERS No No.6 G-6 G-0 G- G- G-6 63 G- G- G-5 G G-3 G-3 No No Shaded Parts are not used

7 No. Steering Nut 5.8mm Pillow Ball (silver) 6 5 Saver Nut Servo Saver Spring mm Steering No..6mm Nut Steering Pin 0 3 x 6mm Metal Bushing 5.8mm Pillow Ball (silver).6mm Nylon Nut.6mm 8 0 No. 3 Steering 3 x 8mm 3 F/H Screw Unicrank Shaft x 8 x.5mm Plastic Bushing x8mm 3x8mm Part bags used. Cut off shaded portion. Ensure smooth non-binding Apply grease. 0 Ball bearings are optional! movement while assembling. (with optional part no.) 7

8 Gear Differential No. 0 6 x 8mm TP TP Screw 8 7 x8mm 3 x 0mm Shaft O O-ring x8mm x 5 Gearbox No. xmm Firmly tighten the set screws onto the flat spots. 5mm 3x0mm 5 xmm 5mm 3 3 Gear Differential 8 3x0mm 6 7 xmm Rear 3x0mm x mm 7 5 x 0mm Set Screw Ball Bearing 5 3 x 0mm TP TP Screw (Silver) 8 E E E-ring 8 x mm Ball Bearing 5mm Washer Front 3 Firmly tighten the set screws onto the flat spots. x x For Front For Rear x Part bags used. Apply grease. Assemble as many times as specified. Apply threadlocker (screw cement). 8

9 No.3 6 Front Suspension < Left > x mm Set Screw 5.8mm Pillow Ball (silver) 3 mm 3 3 x 8mm Ball Bearing < Right > 30 L L marked mm Hex Wrench (5mm) 33 6 x mm Ball Bearing R 3 mm Pillow Ball R R marked xmm 35 mm Pillow Ball Nut Firmly tighten the set screws onto the flat spots. 36 xmm Inside 36 No.3 7 Front Suspension < Right > 3 x Set Screw 3 3 x 0mm Set Screw 5.8mm Pillow Ball (silver) < Left >.5mm Hex Wrench (.5mm) 3x 6 E3 E E-ring 38 3x0mm For adjusting the ride height. E Suspension Shaft (E) D Suspension Shaft (D) 0.5mm 6 mm Part bags used. Ensure smooth non-binding Assemble left and right sides the same way. movement while assembling.

10 No.3 8 Front Suspension 5mm approx. 5mm 30 3 x 0mm TP TP Screw (Silver) < Left > 5.5mm approx. 5.5mm 3x0mm 3.5mm Hex Wrench (.5mm) < Right > Tighten this screws reciprocally. Front Suspension No x mm TP TP F/H Screw O O-ring 3 Front Gearbox Inside 3 Note the direction. Note the direction. Front 3xmm 3xmm 0 Steering 5 5.8mm L Ball End (L) No x 6 3 x 0mm Set Screw 8mm approx. 8mm 0 x Part bags used. Assemble left and right sides True-to-scale diagram. Assemble as many times as specified. the same way. Apply grease.

11 No. Center Gearbox 7 Front 3 x 6mm TP TP Screw (Silver) 3 x 0mm TP TP Screw (Silver) 8 x mm 3x30mm 53 3 x 30mm Ball Bearing Screw mm Aluminium Spacer 3 x 0mm Shaft 3x6mm 3x0mm 5 5 Note the direction. No. Center Gearbox x mm Set Screw 3 x 55 Set Screw 3 x mm 3x Screw Brake Piston xmm 6mm xmm Note the direction for 5 and xmm 5 Top mm approx. 5.5mm 56 Firmly tighten the set screws onto the flat spots. 3xmm No. 3 Center Gearbox 3 x mm TP TP F/H Screw 6 3 3xmm 3xmm Part bags used. Apply threadlocker Apply rubber type glue. Assemble in the Ensure smooth non-binding Apply grease. (screw cement). specified order. movement while assembling.

12 No.5 Rear Suspension 3 x 8mm Ball Bearing 3 < Left > 68 mm Pillow Ball Nut < Right > 6 3 L L marked mm Hex Wrench (5mm) 67 mm Pillow Ball 6 x mm Set Screw 66 R R marked xmm x mm Ball Bearing xmm Firmly tighten the set screws onto the flat spots. 36 Inside No.5 5 Rear Suspension 70 < Left > 6 7.5mm Hex Wrench (.5mm) For adjusting the ride height. 7 Suspension Shaft (F) 3xmm mm 73 C Suspension Shaft (C) 6 6 3x0mm 73 3 x mm Cap Screw < Right > 5.8mm 6 Pillow Ball (silver) mm Ball Use center hole. 3 x 0mm Set Screw 63 7 Part bags used. Ensure smooth non-binding movement while assembling. Assemble left and right sides the same way.

13 No.5 6 Rear Suspension < Right >.5mm approx..5mm mm approx. mm.5mm approx..5mm < Left > Tighten this 3 screws reciprocally..5mm Hex Wrench (.5mm) No.5 7 Rear Suspension < Right > 3x0mm 3 x 0mm TP TP Screw (Silver) 3 Note the Front direction. Rear Gearbox 7 3 Inside 3 Note the direction. < Left > No.3, No.5 8 Rear Suspension 3 x mm TP TP F/H Screw O O-ring xmm 3xmm 3xmm Part bags used. Assemble in the specified order. Assemble left and right sides the same way. Apply grease. 3

14 Shock 5 5.8mm L Ball End (L) No x approx. 78 Shock Shaft G 77 E.5 E E-ring Cover the shaft with cloth before gripping it with pliers. 77 x 0 Shock No.6 Oil G3 Pull down the piston 0 ~ mm and slowly fill in oil. 8 0 ~ mm 80 Add oil one more time up to the brim. Piston Then, gently move the piston up and down to get rid of air bubbles G3 Put 8 onto 7, wipe up any Ensure smooth piston excess oil and screw on G3 move-ment. together with 80. Should a piston not move smoothly. x Shock No.6 G6 Compress the spring and install G mm Ball G6 G5 8 G Use mm size spacer. 83 mm x x Part bags used. Assemble as many times as specified.

15 No.3 Front Shock 3 x mm Cap Screw 8 3xmm 3 Rear Shock No.5, No.7 3x0mm 3x0mm 3 x mm Cap Screw 3 x 0mm TP TP Screw (Silver) 86 3x0mm 3x0mm 85 3xmm 3 3 No.7 Front Bumper 3 x 0mm TP TP Screw (Silver) 3 x mm TP TP F/H Screw 87 3xmm 3x0mm Part bags used. Assemble left and right sides the same way. Assemble in the specified order. 5

16 5 Side Bumpers 88 No.7 3 x 8mm F/H Screw () FUTABA SRN-3F In case of using Futaba SRN-3F control block unit assemble left side bumper. 3x8mm 3x8mm 8 3x8mm 3x8mm 6 Fuel Tank No.8 0mm Silicone Tube Cut to one 0mm piece. Silicone Tube 80mm Cut to one 80mm piece. 0 0 Triming 3 x mm TP TP F/H Screw 3xmm Part bags used. 6

17 7 Engine 3 x 8mm Screw 3 x 8mm F/H Screw 3 No.8 Tighten the screws with one sheet of paper inserted between both gears. Engine Assembly mm Silicone Tube (80mm) 3x8mm(F/H) 3x8mm(F/H) 3x8mm 3x8mm 8 Engine No., No.8 3 x mm TP TP F/H Screw x 30mm Cap Screw xmm Nut 5 x mm Set Screw 8 Front View Assemble muffler hke picture. 3xmm 3x30mm Part bags used. True-to-scale diagram. Cut off excess. 7

18 No., No. Radio Use the same type of screw as supplied with the servos..6 x 8mm TP.6 x 8mm TP Screw Screw 0 3 x 0mm TP 3 x 8mm TP Screw (Silver) Screw Steering Servo In case of using servo horn which come with transmitter. F mm Pillow Ball (Black).6mm.6mm Nut 5.8mm Pillow Ball (Silver) Nut FUTABA SANWA KO JR HITEC H S F ~6mm 30 Radio 3 x 0mm TP TP Screw (Silver) 3 x 5mm TP TP Screw 3 x 8mm TP TP Screw No., No. 3x5mm Throttle Control Servo 3x8mm 07 3x8mm 3x0mm x5mm x0mm 05 Steering Servo No. 3 Radio Box 3 x 0mm TP TP Screw (Silver) Switch x0mm 3x0mm x8mm.6x5mm 3x0mm.6 x 5mm Screw x 8mm TP TP Screw 0 Switch 0 8 Part bags used. Cut off shaded portion. Must be purchased separately! Ensure smooth non-binding movement while assembling.

19 3 Radio 3 x 0mm TP TP Screw (Silver) No.7 Antenna 3x0mm 3 Hook Pin 3x0mm Receiver Battery Box Receiver Connect as per radio instruction manual. If receiver and battery move in the box. Add sponge or some others for holding. 33 Chassis 3 x 0mm TP TP Screw (Silver) 5 3 x mm Screw 3x0mm 3xmm 3x0mm 3x0mm 3 Steering No mm L Ball End (L) 0 F 5 3 x 30mm Adjustable Rod Adjust degree of tightness of both parts and make servo rod look as shown mm approx. 5mm Part bags used. Must be purchased separately! True-to-scale diagram. Pay close attention here!

20 35 Radio No. x 0mm Screw x0mm 3x 3 x Set Screw 8 mm Stopper Spring 6 Throttle Rod mm Nylon Nut 7 Brake Rod 6 3x 8 Servo Horn mm 7 0 mm 8 Note the top and bottom. 0mm approx.0mm Holes used. 6mm approx. 6mm No. Note the direction. 36 Radio Tapered Washer Silicone Tube Supplied with the servo. Neutral 0mm approx. 0mm 5 mm No 37 Throttle Linkage Adjustment approx.mm ( ) ( ) ( High ) ( Idle ) mm approx.mm Adjust with throttle ( ) stop screw. ( Brake ) Contracted. Throttle Stop Screw 3 Position where brake starts working. Confirm the setting before installation. 0 mm Part bags used. Tentatively Ensure smooth non-binding True-to-scale Cut off shaded Must be purchased Cut off excess. mm Drill holes with the tighten. movement while assembling. diagram. portion. separately! specified diameter.

21 38 Wheels 7 (thin : for front) 8 (thick : for rear) 5 (thin : for front) 6 (thick : for rear) (thin : for front) 30 (thick : for rear) x x For Front For Rear Fit wheels inside tyres as shown. Twist the tyre onto the wheel. After fitting wheels to tyres, apply instant glue as shown. 3 Wheels < Rear > For Rear < Front > Wheel Bolt For Front Cross Wrench 0 Body Mounts No.7 3 Widen the slit with a screwdriver and fit in Note the direction of 3 and assemble two of the snap. each kind. 35 x Part bags used. Apply rubber type glue. Apply instant glue Assemble as many Assemble left and right (CA glue, super glue). times as specified. sides the same way.

22 Body Mounts No.7 x 8mm TP TP Screw 3 x 0mm TP TP Screw (Silver) 3 x 5mm TP TP Screw 3x5mm 3x0mm < Rear > < Front > x8mm x8mm Body Shell 6mm 6mm Part bags used. Cut off shaded portion. Assemble left and right sides the same way. Drill holes with the specified diameter.

23 3 Painting Before painting, use a neutral detergent to remove any oil residues and dirt. Mask the windows from the inside. 3 Refer to the pictures on the box for the color scheme. After painting, remove the protective film from the body shell. A- Paint the body shell from the inside using KyoshoÕs spray colors. Yellow B-7 No.760 Black A- Chrome Silver Mask No.7630 Yellow Mask No.7630 Black Chrome Silver Chrome Silver Chrome Silver Plastic Parts 3 x 6mm TP TP Screw 3 x 8mm TP TP Screw 8 A- Nut B-7 A-0 3x6mm Double-sided Tape 3x8mm B- B- B- 3x6mm Double-sided Tape 3x8mm B- Washer B-6 A- 3x8mm 3x8mm Do not overtighten the nuts! Part bags used. Pay close attention here! 3

24 5 Decals The decal numbers between brackets are only for the opposite side ( 6 ) 3 8 ( ) 0 ( ) 73 6 ( 70 ) ( 5 ) 67 ( 68 ) 65 ( 66 ) 6 7 ( 8 ) Body Shell Always run your car with the body shell mounted! Do not run your car on ground: Safety Precautions that is overgrown with grass. that is muddy, sandy or rocky. Check all screws, nuts etc. on a regular basis for looseness. Assemble in the specified order.

25 Shock Spacer G5 (Shock Spacer) 3 x 0mm TP TP Screw 3x0mm G0 (Shock Spacer Holder) Installation of Fuel Filter M No.3308 Fuel Filter (M) 3 x 0mm TP TP Screw 3x0mm 0 Transponder Stay 36 Installation of 36 Cooling Fan Set 3x0mm 3x30mm 5 3x6mm 5 Must be purchased separately! 5

26 FUTABA SRN-3F Installation of FUTABA SRN-3F Unit 3 x 0mm TP TP Screw 3x0mm Switch Boots SRN-3F Futaba SRN-3F Unit L L marked R R marked In case of using slide type carburetor. Refer follouing picture for assembling. x0mm x 0mm No.7 Screw 3x 3 x Set Screw mm Stopper 3 mm Ball End 7 Brake Rod 38.6 x 5mm Rod Spring mm Nylon Nut Tapered Washer 0mm approx. 0mm 7 Supplied with the servo. mm 0 8 Servo Horn Note the top and bottom. Neutral 5 Part bags used. Must be purchased separately! Ensure smooth non-binding Cut off shaded movement while assembling. portion. mm mm Drill holes with the specified diameter. Tentatively tighten. True-to-scale diagram. 6

27 Shock () ADJUSTMENT G5 Adjust the ride height by changing the guantity and / or type of shock collars used. Adjust the caster by changing the location of the Spacer. G5 (mm) G5 (.5mm) G5 (mm) Front Suspension 3 Caster 8 Caster : approx. 8 Caster : approx. û Camber Angle (for front & rear approx. û) û Camber Angle (for front & rear approx. û) Generally, the bigger the caster, the milder cornering becomes. Ride Height 0mm width approx. 0mm G5 Increasing G5 shock collar width. Ride height becomes higher. G5 Decreasing G5 shock collar width. Ride height becomes lower. Camber Adjust the camber by tightening or unscrewing the pillow ball. < Front > 3 Do not loosen too much since will Swingshaft fall out. Shock () Adjust the steering behaviour by changing the spring tension and / or type of shock oil. Spring stiffness Hard Soft Steering Characteristics.5mm Hex Wrench (.5mm) Camber Angle (Large) Steering becomes milder. Camber Angle (Small) Enters corners more aggressively. Front Sharp Mild Steering Rear Suspension Toe Angle characteristics < Rear > Rear Grip gets lower. Grip gets higher. 3 û Adjust camber approx. û approx. û < Spring > Spring stiffness Hard Soft S On-road Shock Spring(S) Yellow Green Orange < Shock Oil > Spring stiffness Silicone Oil # 600 # 500 (660) (6608) Hard Soft # 00 # 00 (6603) (660) # 00 # 300 (6607) (6605) approx. û Rear toe angle give stability..5mm û Hex Wrench (.5mm) Adjust camber approx. û Steering Characteristics Camber Angle (Large) Gives rear tires more grip when entering corners. Camber Angle (Small) Rear tire grip becomes worse when entering corners. 7

28 OPERATING YOUR MODEL SAFELY CAUTION: Do NOT operate the model in the following places and situations: (Non-observance may lead to accidents!) Always check the dry batteries in the radio! When the dry batteries get weaker, transmission and reception of the radio decrease. You may lose control of your model when operating it under such condition. This may lead to accidents! Operate the model in spacious areas with no people around! Do NOT operate it:. on roads!. in places where children and many people gather! 3. in residential districts and parks!. indoors and in limited space! * Non-observance may account for personal injury and property damage! Keep in mind that people around you may also operate a radio control model! NEVER share the same frequency with somebody else at the same time! Signals will be mixed and you will lose control of your model. This may lead to accidents! When the model is behaving strangely...! Immediately stop the model and check the reason. As long as the problem is not cleared, do NOT operate it! This may lead to further trouble and unforeseen accidents! Handle fuel ONLY ONLY use glow fuel for radio control models! outdoors! Vapors and exhausts are very noxious to health! CAUTION: in order to avoid accidents and personal injury, be sure to observe the following: Because the use of gasoline and kerosene in R/C models ac-- counts for fires, do NOT use them! Fuel is highly inflammable and Do NOT put fingers or any objects inside high-explosive! rotating and moving parts!. NEVER use fuel indoors or in places Rotating / moving at high with open fires and sources of heat! speed, you may be. Store fuel ONLY in cool, dry and dark seriously injured! places out of children's reach! Tightly shut the cap! 3. Do NOT dispose of empty fuel cans into a fire! There is danger of explosion! NEITHER swallow fuel NOR let it into your eyes! Immediate measures Right after use, do NOT should be taken: touch equipment on the if fuel is swallowed, inmodel such as the engine -duce vomit-ing. If fuel and muffler, because they gets into eyes, rinse generate high temperatures! them and consult an orphamologist! You may burn yourself seriously touching them! 8

29 SPARE PARTS FOR JAPANESE MARKET ONLY. No. No. No. Part Names Quantity No. Part Names Quantity AB-5 Clutch Shoe 53 x GT-5 Pilot Shaft 5 x AB-7 Clutch Spring 5 x 350 LA- Steering Pin 0 x 50 BS-6 6.8mm 6.8mm Ball 6 x 0 50 LA-3 Servo Saver Shaft Set x 300 FD- Flywheel Set 5 x 650 LD-70 Clutch Bearing x 580 FD-33 EG x Tail Pipe 7 x 30 OR- EG Body Attachment x 600 FD-65 GP 3 x 05 x Linkage Set (for GP cars) 00 OT x 8 x 3 Joint 3 x 300 FM- Clutch Bell 5T (5T) 57 x 00 OT-8 Differential Gear Set x 7 8 x 750 FZ-0 Gear Box 5 x 300 OT- O O-ring x 0 00 FZ-3 Final Differential Case x x 00 OT-35 Upper Rod Set 5 x 5 x FZ- Center Plate 8 x 00 OT-36.6mm.6mm Pillow Ball (Black) 7 x FZ-5 mm mm Pillow Ball 3 x 50 SPW-5 Stainless Disk Rotor 58 x 5 60 x 000 FZ-8 C SS x 77 x Suspension Shaft (C) 73 x 50 W-56 Racing Shock (SS) G x FZ-3 5.8mm Center Shaft (Rear) x mm Pillow Ball (Silver) x 8 00 FZ-5 FW-0 Main Chassis (FW-0) 5 x 700 S 000 Fluorescent Strap (S) x 0 KP,KY 80 FZ-5 FW-0 70 M Upper Deck (FW-0) 03 x 00 KP,KY Fluorescent Strap (M) 6 x 50 FZ-53 Knuckle Arm 30 x Color Antenna (White) x FZ-5 Rear Hub x Color Silicone Tube x 00 FZ-55 Front Suspension Arm x x x0mm 5x0mm Ball Bearing 7 x 700 FZ-56 Rear Suspension Arm x 600 8xmm 8xmm Ball Bearing x 700 FZ-57 Front Bulkhead x Air Cleaner 3 x 500 FZ-58 Center Bulkhead x GS5-R GS5-R Engine 50 x 3000 FZ-5 Rear Bulkhead x Engine Mount Plate x 00 FZ-60 Bumper Set x Muffler Gasket 3 x 5 00 FZ x Receiver Box Set Heat-resistant Muffler Joining Pipe 5 x 800 FZ-6 3T Spur Gear (3T) 8 x Snap Pin x 0 00 FZ-63 Disk Holder 56 x 00 Servo Saver Tube 5 6 x 500 FZ-6 3 Spur Gear Shaft 7 x 50 Servo Saver Tube Plastic Parts x 3 x 300 FZ-65 Front Center Shaft 6 x SS Muffler 7 x 00 FZ-66 D Suspension Shaft (D) 6 x 50 7 Manifold 3 x 600 FZ-67 Suspension E 6xmm Shaft (E) x xmm Ball Bearing 33 x 00 FZ-68 Suspension F Shaft (F) 7 x O 5 P. Silicone O-ring P.5 (slim) x FZ-6 Swingshaft 3 x x8mm x8mm Ball Bearing 3 x 800 FZ-70 Brake Lever x 300 FZ-7 50 Wheel Shaft 3 x Some of the parts included are not available as spare parts. Purchase FZ-7 Wheel Stopper Bolt 3 x 00 optional parts instead. FZ-73 Drive Washer 36 x 00 FZ-7 mm mm Pillow Ball 67 x 3 50 FZ-75 mm mm Pillow Ball Nut 68 x FZ-76 mm mm Pillow Ball Nut 35 x 300 FZ-77 00cc Fuel Tank (00cc) 0 x 000

30 No. FZW- FZW-3 FZW- FZW-8 FZW- FZW-5 FZW-6 FZW-30 FZW-5 FZW-5 FZW-53 FZW-5 FZW OPTIONAL PARTS FOR JAPANESE MARKET ONLY. No. No. Part Names Quantity No. Part Names Quantity C 73 6v-600mAh Titanium Suspension Shaft (C) instead of v-600mAh Ni-Cd Battery , 6v-000mAh Steel Differential Bevel Gear instead of 7, v-000mAh Ni-Cd Battery & Steel Differential Pinion Gear instead of Locking Jig & Wrench 800 Steel Differential Gear Set Maintenance Stand Carbon Steering Plate instead of Onroad Spring Set (Hard Type) Hard Deff Case instead of Multi Ride Height Gauge , mm Viscus Cup Ring instead of 75, Titanium Adjust Rod 30mm instead of 5. pcs Cycle Fitting Kit When Mounting Cycle Engines 800 Onroad Spring Set instead of 8. 3 types mm Hard Main Chassis instead of Titanium Adjust Rod 0mm pcs. for Tie Rod Carbon Upper Deck instead of Muffler Stay strengthened 600 3, 3 57, 58 3T Universal Swingshaft instead of 3, One-piece Clutch Bell 3T instead of 57, Front Stabilizer Set T One-piece Clutch Bell T 5x0mm 600 5x0mm Ball Bearing 5T Rear Stabilizer Set One-piece Clutch Bell 5T 600 6T One-piece Clutch Bell 6T 600 7T One-piece Clutch Bell 7T 600 8T FZW-56 -Speed Automatic Transmission Set FZW-60 Low Height Engine Mount *Not available with Pull Start Engine FZW-6 High Balance Flywheel Use with FZW One-piece Clutch Bell 8T FZW-6 High Balance Flywheel (-speed) Use with FZW-60. Onroad Spring Set (Soft Type) FD- CZ-R O.S., Flywheel (CZ-R) for O.S., ENYA Engines Clutch Spring (Hard) W mm M mm Hard Ball (M3.0) instead of 83. hard anodized Dual Spring Assort Set W mm M mm Hard Ball (M3.0) instead of 6. hard anodized Loctite (medium strength) W55 SS Teflon Touring Shock (SS) One-touch Plug Heat Set W555 SS 50cc Adjustable Teflon Shock (SS) Quick Fill Fuel Bottle (50cc) 5 5.8mm 5 / HG KP,KY 5.8mm Ball End instead of 5. Fluorescent Pink / Fluorescent Yellow HG Joint Grease 706 Color Antenna (Fluorescent Pink) Oneway Bearing Grease 707 Team 5 Color Antenna (Fluorescent Yellow) Team Circuit Shock (5 different setting) 70 3, 3 Special Antenna Holder Power Universal Shaft instead of 3, / KP,KY Color Silicone Tube instead of. Fluorescent Pink / Fluorescent Yellow x8mm x8mm Ball Bearing instead of 3. pcs Air Cleaner Oil 6605 Silicone Oil M cc Fuel Filter (M) Urethane Foam Bumper , 6 Steel Final Differential Case instead of 0, Cooling Fan Set O.S. Special Engine Mount When Mounting O.S. Engines FRP 58 FRP Brake Disk instead of FRP 58 FRP Brake Disk (Thin Type) instead of 58. pcs , 7 Tuned Muffler Set (Red) instead of, Vespel Clutch Shoe instead of SuperTen Tire Box (SuperTen) SC Spring Connect Super Tuned Muffler Spring Connect Type 8000 # Differential Gear Grease # # Silicone Oil 0cc #5000 Differential # Gear Grease 30

31 ,, WHEEL, TIRE, BODY SET FZ-7G FZ-7W FZ-80G FZ-80W FZ-8BK FZ-8S FZ-8W FZ-8BK FZ-8S FZ-8W Low Profile Wheel (Gun metallic) x Low Profile Wheel (White) x Low Profile Wide Wheel (Gun metallic) 30 x Low Profile Wide Wheel (White) 30 x 8-Spoke Wheel (Black) 8-Spoke Wheel (Silver) 8-Spoke Wheel (White) 8-Spoke Wide Wheel (Black) 8-Spoke Wide Wheel (Silver) 8-Spoke Wide Wheel (White) Mercedes CLK Body Set (AMG Mercedes CLK) D Decal Set (D) decals x 800 WARSTEINER Decal Set (WARSTEINER) 500 decals x GT Body Set (PORSCHE GT) 00 Body Set (CALSONIC SKYLINE) 3800 Body Set (ESSO TOM'S CHASER) 00 SOKF-GTR Body Set (SOK McLaren F-GTR) 00 NSX Body Set (Castrol MUGEN NSX) 00 GT Body Set (Castrol Supra GT) R V K-ZERO 5R K-ZERO Slick Tire 5R for Front 5R K-ZERO 5Z K-ZERO Slick Tire 5Z K-ZERO 30Z Molded Mesh K-ZERO Slick Tire 30Z High Grip Tires 30 K-ZERO 30V K-ZERO Slick Tire 30V V K-ZERO 0Z K-ZERO Slick Tire 0Z K-ZERO 5R K-ZERO Slick Tire 5R for Rear K-ZERO 5Z K-ZERO Slick Tire 5Z 500 K-ZERO 30Z Molded Mesh K-ZERO Slick Tire 30Z High Grip Tires 500 K-ZERO 30V K-ZERO Slick Tire 30V 500 K-ZERO 0Z K-ZERO Slick Tire 0Z 500 No mm Size (mm) QUANTITY No. Round Head Screw 00 x6 x8 x0 x5 5 each 3 x x6 x8 x0 5 each 7 mm.6mm 0 each.6x8.6x0.6x.6x 5 each 33.6x6.6x8.6x0.6x5 each 7 mm 0 each 3x 3x6 3x8 3x0 3 x 5 each 3 3x6 3x8 3x0 3x 3x 5 each 3x 3x6 3x8 3x0 5 each 35 3x5 3x6 3x8 3x0 5 each Flanged Nut 00 x6 x8 x0 x 3x 3x 3x6 3x8 5 each 5 each x5 3x30 3x35.6x.6x5.6x6.6x8 5 each 5 each 7 75 mm 0 pcs 0 pcs Bind Screw 00 Bind Self-Tapping Screw 00 Nylon Nut 00.6x.6x6.6x8.6x5 each 3x 3x6 3x8 3x0 3x 5 each 0.6x6.6x8.6x0.6x5 each 3x6 3x8 3x0 3x 3x 5 each mm 5 pcs 5 pcs 3x5 3x6 3x8 3x0 5 each 7 mm 5 pcs 3 x0 x5 x8 5 each 3x 3x6 3x8 3x0 x6 x8 x0 x 3x 3x5 3x8 3x30 x5 x8 x0 x Flat Head Screw 5 each 5 each 5 each 5 each 00.6x8.6x0.6x.6x 5 each 3x6 3x8 3x0 3x 5 each 3x 3x6 3x8 3x0 5 each x8 x0 x5 x0 5 each 3x 3x 3x6 3x8 5 each 3x30 3x3 3x3 3x35 5 each Cap Screw 00 x8 x0 x x each.6x8.6x0.6x.6x each 3x8 3x0 3x 3x each 3x5 3x6 3x8 3x0 each 3x5 3x30 3x35 3x0 each x0 x5 x0 each x5 x8 x30 each x35 x0 x5 each SCREW NUT etc FOR JAPANESE MARKET ONLY. mm Size (mm) QUANTITY No. mm QUANTITY Round Head Self-Tapping Screw 00 Nut 00 Flat Head Self-Tapping Screw x6.6x8.6x0.6x5 each 3x6 3x8 3x0 3x 3x 5 each 3x5 3x6 3x8 3x0 5 each 85 x5 x0 x5 5 each 86 Flanged Cap Screw 00 3x6 3x8 3x0 x8 x0 x x8 x0 Screw 00 Set Screw 3x6 3x 3x 3x6 3x3 3x 3x5 3x0 x x5 x8 x 5x 5x5 5x6 5x30 5x0 each each 0 each 00 3 each 3 each 3 each 3 each 3 each 65 3x0 3x5 3 each mm E.5 E.0 E.5 E3.0 E.0 E5.0 E6.0 E7.0 E0.0 Flanged Nylon Nut 00 Washer 00 mm.6mm mm 5mm E E-Clips 5 pcs 0 each 0 each 50 0 pcs 0 pcs 0 pcs 0 pcs 0 pcs 0 pcs 0 pcs 6 pcs 6 pcs 3

32 SuperTen FW KYOSHO / EXPLODED VIEW < > Parts indentified only by key numbers are not sold individually FZ-7 3 OR- W-56 FZ-56 6 FZ FZ-5 7 FZ-5 7 FZ-6 3 FZ-5 85 OT-5 3 OT FZ-3 6 OT- FZ-60 3 W-56 OT-5 3 FD-65 7 FD-65 6 FZ FZ-3 FD FZ-3 6 FZ-3 0 FZ-0 5 FZ-5 70 OT-5 3 FZ-5 66 FZ FZ FZ FZ-56 6 FZ-68 7 FZ-56 6 BS-6 6 FZ FZ FZ I J FZ FZ-7 67 FZ FZ FZ-7 67 FZ FZ-5 65 FZ FZ-7 3 FZ-6 3 FZ-6 0 FZ-7 3 FZ-8S OT J E G F C D E H I G H B F C FZ-5 5 LA-3 LA- FZ-6 OT OT OT-35 5 FZ-77 0 FD-65 FZ-5 03 FD-65 0 FD FZ-60 0 FZ-6 0 FZ-6 07 FZ FZ FZ FZ-6 06 FZ FZ FZ-58 5 FZ-6 8 FZ FZ-6 7 FZ-6 FZ-6 FZ-70 5 FD-65 FZ FZ-7 3 LD LD FM- 57 FD-65 5 AB-7 5 AB-5 53 GT-5 5 FD- 5 FZ FZ-6 3 FZ-0 OT- FZ FZ-55 OT FZ-3 6 FZ-3 0 FZ-55 FZ-55 3 FZ-67 FZ-6 3 FZ-0 5 FZ-55 0 FZ-66 OT-8 FZ-3 6 FZ FZ-55 3 FZ-58 5 FZ FZ FZ SPW OT-5 3 OT- OT FZ-55 3 FZ A B A OR FZ FZ-7 3 FZ-8S FZ FZ-53 FZ FZ OT-35 5 OT FZ FZ-5 3 FZ W D 5 G6 G G G3 G0 G5 G6 G G G

33 R THE FINEST RADIO CONTROL MODELS TEL ( PRINTED IN JAPAN