POWERED MONITOR SPEAKER HS80M/HS0M SERVICE MANUAL CONTENTS HS80M SPECIFICATIONS... HS0M SPECIFICATIONS... DIMENSIONS... PANEL LAYOUT... CIRCUIT BOARD LAYOUT... 7 HS80M DISASSEMBLY PROCEDURE... 8 HS0M DISASSEMBLY PROCEDURE... 11 CIRCUIT BOARDS... 1 HS80M INSPECTIONS... 1 HS0M INSPECTIONS... 1 BLOCK DIAGRAM OVERALL CIRCUIT DIAGRAM PARTS LIST PA 01180 HS80M: 0010-70 HS0M: 0010-0 HAMAMATSU, JAPAN Copyright (c) Yamaha Corporation. All rights reserved. PDF Printed in Japan 0.1
HS80M/HS0M IMPORTANT NOTICE This manual has been provided for the use of authorized Yamaha Retailers and their service personnel. It has been assumed that basic service procedures inherent to the industry, and more specifically Yamaha Products, are already known and understood by the users, and have therefore not been restated. WARNING : IMPORTANT : Failure to follow appropriate service and safety procedures when servicing this product may result in personal injury, destruction of expensive components and failure of the product to perform as specified. For these reasons, we advise all Yamaha product owners that all service required should be performed by an authorized Yamaha Retailer or the appointed service representative. This presentation or sale of this manual to any individual or firm does not constitute authorization, certification, recognition of any applicable technical capabilities, or establish a principal-agent relationship of any form. The data provided is believed to be accurate and applicable to the unit (s) indicated on the cover. The research engineering, and service departments of Yamaha are continually striving to improve Yamaha products. Modifications are, therefore, inevitable and changes in specification are subject to change without notice or obligation to retrofit. Should any discrepancy appear to exist, please contact the distributor s Service Division. WARNING : IMPORTANT : Static discharges can destroy expensive components. Discharge any static electricity your body may have accumulated by grounding yourself to the ground bus in the unit (heavy gauge black wires connect to this bus). Turn the unit OFF during disassembly and parts replacement. Recheck all work before you apply power to the unit. WARNING: CHEMICAL CONTENT NOTICE! The solder used in the production of this product contains LEAD. In addition, other electrical/electronic and/or plastic (Where applicable) components may also contain traces of chemicals found by the California Health and Welfare Agency (and possibly other entities) to cause cancer and/or birth defects or other reproductive harm. DO NOT PLACE SOLDER, ELECTRICAL/ELECTRONIC OR PLASTIC COMPONENTS IN YOUR MOUTH FOR ANY REASON WHAT SO EVER! Avoid prolonged, unprotected contact between solder and your skin! When soldering, do not inhale solder fumes or expose eyes to solder/flux vapor! If you come in contact with solder or components located inside the enclosure of this product, wash your hands before handling food. WARNING: THIS APPARATUS MUST BE EARTHED IMPORTANT THE WIRES IN THIS MAINS LEAD ARE COLOURED IN ACCORDANCE WITH THE FOLLOWING CODE: GREEN-AND-YELLOW : EARTH BLUE : NEUTRAL BROWN : LIVE As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows: The wire which is coloured GREEN and YELLOW must be connected to the terminal in the plug which is marked by the letter E or by the safety earth symbol or coloured GREEN and YELLOW. The wire which is coloured BLUE must be connected to the terminal which is marked with the letter N or coloured BLACK. The wire which is coloured BROWN must be connected to the terminal which is marked with the letter L or coloured RED. WARNING Components having special characteristics are marked and must be replaced with parts having specification equal to those originally installed. * This applies only to products distributed by YAMAHA KEMBLE MUSIC (U.K.) LTD.
HS80M HS80M SPECIFICATIONS General specifications Type... Biamp -way Powered speaker Crossover Frequency... khz Overall Frequency Response... Hz-0 khz (-10 db) Dimensiones (W x H x D)... 0 x 90 x mm (9-1/1 x 1-/8 x 1-1/ ) Weight... 11. kg Speaker Components Speaker Components... LF: 8" Cone (Magnetic shielding Type) HF: 1" Dome (Magnetic shielding Type) Enclosure... Type: Bass-reflex Type Material: MDF Amp. unit Output Power... Total: 10 W (dynamic power) (LF: 7 W, ohms, 1 khz) (HF: W, 8 ohms, 10 khz) Input Sensitivity/Impedance... -10 dbu/ 10 k-ohms Input Connectors (parallel)... 1: XLR--1 type (balanced) : PHONE (balanced) Controls... LEVEL control (+ db/ center click) LOW CUT switch (FLAT/ 80/ 100 Hz, 1 db/ octave) MID EQ switch (+/- db at khz) HIGH TRIM switch (+/- db at HF) ROOM CONTROL switch (0/ -/ - db under 00 Hz) Power Indicator... Power ON: White LED Power Consumption... 0 W HS80M/HS0M Performance graph +10 RESPONSE (db) 0-10 -0-0 -0 0 100 1k FREQUENCY (Hz) 10k
HS80M/HS0M HS0M SPECIFICATIONS General specifications Type... Biamp -way Powered speaker Crossover Frequency... khz Overall Frequency Response... Hz-0 khz (-10 db) Dimensiones (W x H x D)... 1 x 8 x mm (-1/ x 10-9/1 x 8-/ ) Weight....8 kg Speaker Components Speaker Components... LF: " Cone (Magnetic shielding Type) HF: 0.7" Dome (Magnetic shielding Type) Enclosure... Type: Bass-reflex Type Material: MDF Amp. unit Output Power... Total: 70 W (dynamic power) (LF: W, ohms, 1 khz) (HF: W, 8 ohms, 10 khz) Input Sensitivity/Impedance... -10 dbu/ 10 k-ohms Input Connectors (parallel)... 1: XLR--1 type (balanced) : PHONE (balanced) Controls... LEVEL control (+ db/ center click) LOW CUT switch (FLAT/ 80/ 100 Hz, 1 db/ octave) MID EQ switch (+/- db at khz) HIGH TRIM switch (+/- db at HF) ROOM CONTROL switch (0/ -/ - db under 00 Hz) Power Indicator... Power ON: White LED Power Consumption... W HS0M Performance graph +10 RESPONSE (db) 0-10 -0-0 -0 0 100 1k FREQUENCY (Hz) 10k
HS80M/HS0M DIMENSIONS HS80M 0 (9-1/1") (1-1/1") 90 (1-/8") Unit: mm (inch) HS0M 1 (-1/") (8-/") 8 (10-9/1") Unit: mm (inch)
HS80M/HS0M PANEL LAYOUT +db MIN LEVEL -10dB 1 HS80M HS0M INPUT MID EQ +db 0dB -db khz ROOM CONTROL 0dB -db -db 00Hz HIGH TRIM +db 0dB -db khz LOW CUT FLAT 80Hz MID EQ +db 0dB -db khz ROOM CONTROL 0dB -db -db 00Hz HIGH TRIM +db 0dB -db khz LOW CUT FLAT 80Hz MID EQ ROOM CONTROL HIGH TRIM LOW CUT +db 0 -db 0 -db -db +db 0 -db FLAT 80Hz 100Hz 7 100Hz 100Hz OFF POWER ON 1 AC IN 8 9 1 POWER switch LEVEL control INPUT 1, connector MID EQ switch ROOM CONTROL switch HIGH TRIM switch 7 LOW CUT switch 8 AC IN Connector 9 Power indicator 1 7 8 9
HS80M/HS0M CIRCUIT BOARD LAYOUT HS80M INPUT (LF /) AMP (LF /) TRANS (LF /) AC INLET (LF 1/) HS0M INPUT (LF /) AMP (LF /) TRANS (LF /) AC INLET (LF 1/) 7
HS80M/HS0M HS80M DISASSEMBLY PROCEDURE HS80M 1. Woofer (Time required: about 1 minute) 1-1 Remove the six () screws marked []. The woofer ring can then be removed. (Fig. 1) 1- Remove the six () screws marked [0]. The woofer can then be removed. (Fig. 1). Tweeter (Time required: about 1 minute) Remove the four () screws marked [0]. The tweeter can then be removed. (Fig. 1). Rear Panel Assembly (Time required: about 1 minute) Remove the ten (10) screws marked [1]. The rear panel assembly can then be removed. (Fig. ). AMP Circuit Board (Time required: about minutes) -1 Remove the rear panel assembly.(see procedure.) - Remove the five () screws marked [90]. The AMP unit can then be removed. (Fig. ) * At this time, be careful not to lose the spacer which also comes off. Tweeter [90] Rear Panel Assembly [0] [0] Woofer [1] [1] [0] [] [] [0] Woofer Ring Fig. 1 [0]: Hexagonal Socket Tapping Screw x0 (WG1100) [0]: Bind Head Tapping Screw x1 (WG000) []: Hexagonal Socket Tapping Screw x0 (WG1100) Fig. [90]: Bind Head Tapping Screw-S x1 (WG100) [1]: Bind Head Tapping Screw x1 (WG000) 8
HS80M HS80M/HS0M - Unsolder soldered parts ( locations) on the pattern side of IC801 and IC80. (Photo. 1) - Remove the two () screws marked [A] and remove the heat sink with IC801 and IC80. (Photo. 1) Remove the two () screws marked [B] and remove IC801 and IC80. (Photo. 1) - Remove the four () screws marked [C], remove the AMP mounting bracket. The AMP circuit board can then be removed. (Photo. 1) HEAT SINK SPACER IC801 [A] IC80 AMP mounting BRACKET AMP [C] CASE PWB AMP mounting BRACKET AMP [C] [B] AMP circuit board AMP INPUT Circuit Board INPUT Photo. 1 <AMP Unit>. INPUT Circuit Board (Time required: about minutes) -1 Remove the rear panel assembly. (See procedure.) - Remove the four () screws marked [110] and the screw marked [11]. (Fig. ) - Remove the LEVEL knob, the hexagonal nut [E] and washer [D]. (Fig., Photo. ) - Remove the hexagonal nut [F] on the phone type input connector. The INPUT assembly can then be removed. (Photo. ) - Remove the three () screws marked [G] and remove the case PWB. (Photo. ) The Input circuit board can then be removed. * The case PWB is not a component of the INPUT circuit board. When replacing the INPUT circuit board, remove the case PWB and reuse it. Photo. <INPUT Assembly> [G] Photo. 9
HS80M/HS0M. TRANS Circuit Board and Power Transformer (Time required: about minutes) -1 Remove the rear panel assembly. (See procedure.) - Remove the four () screws marked [10]. The TRANS circuit board with the power transformer can then be removed. (Fig. ) - Unsolder the power transformer mounting solder ( locations) and separate the power transformer from the TRANS circuit board. * The power transformer is not a component of the TRANS circuit board. 7. AC INLET Circuit Board (Time required: about minutes) 7-1 Remove the rear panel assembly. (See procedure.) Unsold soldered parts ( locations) of the power switch. 7- Remove the two () screws marked [10]. (Fig. ) 7- Unsold the soldered part of the AC inlet grounding wire and remove the AC INLET circuit board. (Photo. ) HS80M Power Switch LEVEL Knob Solder [110] [11] AC INLET Circuit Board Photo. AC Inlet [10] [10] [D] [E] Fig. [110]: Bind Head Tapping Screw-S x10 (WG100) [11]: Bonding Tapping Screw-B x10 (WH0000) [10]: Bind Head Tapping Screw-S x10 (WG100) [10]: Bind Head Screw-S x1 (WG100) Photo. [F] 10
HS0M HS0M DISASSEMBLY PROCEDURE HS80M/HS0M 1. Woofer (Time required: about 1 minute) 1-1 Remove the four () screws marked []. The woofer ring can then be removed. (Fig. 1) 1- Remove the four () screws marked [0]. The woofer can then be removed. (Fig. 1). Tweeter (Time required: about 1 minute) Remove the four () screws marked [0]. The tweeter can then be removed. (Fig. 1). Rear Panel Assembly (Time required: about 1 minute) Remove the ten (10) screws marked [1]. The rear panel assembly can then be removed. (Fig. ). AMP Circuit Board (Time required: about minutes) -1 Remove the rear panel assembly. (See procedure.) - Remove the three () screws marked [90]. The AMP unit can then be removed. (Fig. ) * At this time, be careful not to lose the plate which also comes off. Tweeter [90] Rear Panel Assembly [0] [0] Woofer [1] [1] [0] [] [] [0] Woofer Ring Fig. 1 [0]: Hexagonal Socket Tapping Screw x0 (WG1100) [0]: Bind Head Tapping Screw x1 (WG000) []: Hexagonal Socket Tapping Screw x0 (WG1100) Fig. [90]: Bind Head Tapping Screw-S x10 (WG100) [1]: Bind Head Tapping Screw x1 (WG000) 11
HS80M/HS0M HS0M - Unsolder soldered parts ( locations) on the pattern side of IC801 and IC80. (Photo. 1) - Remove the two () screws marked [A] and remove the heat sink with IC801 and IC80. (Photo. 1) Remove the two () screws marked [B] and remove IC801 and IC80. (Photo. 1) - Remove the four () screws marked [C], remove the AMP mounting bracket. The AMP circuit board can then be removed. (Photo. 1) [A] HEAT SINK IC80 AMP mounting BRACKET AMP CASE PWB PLATE IC801 [C] AMP mounting BRACKET AMP [C] [B] AMP Circuit Board AMP INPUT Circuit Board INPUT Photo. 1 <AMP Unit>. INPUT Circuit Board (Time required: about minutes) -1 Remove the rear panel assembly. (See procedure.) - Remove the four () screws marked [110] and the screw marked [11]. (Fig. ) - Remove the LEVEL knob, the hexagonal nut [E] and washer [D]. (Fig., Photo. ) - Remove the hexagonal nut [F] on the phone type input connector. The INPUT assembly can then be removed. (Photo. ) - Remove the three () screws marked [G] and remove the case PWB. (Photo. ) The Input circuit board can then be removed. * The case PWB is not a component of the INPUT circuit board. When replacing the INPUT circuit board, remove the case PWB and reuse it. Photo. <INPUT Assembly> [G] 1 Photo.
HS0M. TRANS Circuit Board and Power Transformer (Time required: about minutes) -1 Remove the rear panel assembly. (See procedure.) - Remove the four () screws marked [10]. The TRANS circuit board with the power transformer can then be removed. (Fig. ) - Unsolder the power transformer mounting solder ( locations) and separate the power transformer from the TRANS circuit board. * The power transformer is not a component of the TRANS circuit board. HS80M/HS0M 7. AC INLET Circuit Board (Time required: about minutes) 7-1 Remove the rear panel assembly. (See procedure.) Unsold soldered parts ( locations) of the power switch. 7- Remove the two () screws marked [10]. (Fig. ) 7- Unsold the soldered part of the AC inlet grounding wire and remove the AC INLET circuit board. (Photo. ) LEVEL Knob Power Switch Solder [110] [11] AC INLET Circuit Board Photo. AC Inlet [10] [10] [D] [E] Fig. [110]: Bind Head Tapping Screw-S x10 (WG100) [11]: Bonding Tapping Screw-B x10 (WH0000) [10]: Bind Head Tapping Screw-S x10 (WG100) [10]: Bind Head Screw-S x1 (WG100) [F] Photo. 1
HS80M/HS0M CIRCUIT BOARDS HS80M / HS0M INPUT CN0: to POWER INDICATOR- CN0 CN0: to INPUT-CB101 LOW CUT 100Hz 80Hz FLAT AMP CN01: to WOOFER and TWEETER -db HIGH TRIM 0 +db ROOM CONTROL -db -db 0 INPUT MID EQ -db 0 +db CB101: to AMP-CN0 CN80: to TRANS-CN80 * 1 * 1 Component side WOOFER 1 LEVEL MIN -10dB CN0: to AMP-CN0 TWEETER * 1: IC01 and 0 are not components of the AMP P.C.B.. Component side CN80: to TRANS-CN801 TRANS POWER INDICATOR CN80: to AMP-CN80 AC INLET POWER SWITCH * * CN801: to AC INLET-CN80 Component side * : T801 is not a component of the TRANS P.C.B. CN80: to AC IN AC IN Component side * : The power switch is not a component of the AC INLET P.C.B.. Note) The parts in each P.C.B. vary depending on models, destinations, etc. For the parts information, refer to Parts List. 1
HS80M HS80M INSPECTION 1. Test conditions (1) Input Signal: PHONE 1 khz (), 10 khz (TW) () Output load: ohms (), 8 ohms (TW) () AC power supply: AC100 V, 0/0 Hz (J) AC10 V, 0 Hz (U, T) AC0 V, 0 Hz (B, H, O) AC0 V, 0 Hz (K) AC0 V, 0 Hz (A) () VR-Level: MAX MID EQ SW: 0 ROOM CONTROL SW: 0 HIGH TRIM SW: 0 LOW CUT SW: FLAT. Specifications HS80M/HS0M ITEM INPUT CONDITIONS OUTPUT CONDITIONS LIMIT 1 OUTPUT POWER 1 % THD OUTPUT TW > 0 W > W GAIN INPUT: PHONE -10 dbu, 10 khz INPUT: PHONE -10 dbu, 1 khz TW ± dbu ± dbu T.H.D. INPUT SIGNAL: 10 khz INPUT SIGNAL: 1 khz 1 W OUTPUT 10 W OUTPUT TW < 0. % FREQUENCY RESPONSE INPUT SIGNAL:. khz INPUT SIGNAL: khz INPUT SIGNAL:. Hz REF: TW OUTPUT 10 khz 1 W REF: OUTPUT 1 khz, 1 W TW - ± db - ± db ± db MID EQ SW: - REF: MID EQ SW: 0 - ± 1. db MID EQ SW: + ROOM CONTROL SW: - INPUT SIGNAL: khz REF: ROOM CONTROL SW: 0 + ± 1. db - ± 1. db ROOM CONTROL SW: - TONE-CONTROL HIGH TRIM SW: - CHARACTERISTIC HIGH TRIM SW: + LOW CUT SW: 80 Hz INPUT SIGNAL: 00 Hz REF: HIGH TRIM SW: 0 INPUT SIGNAL: 10 khz REF: LOW CUT SW: FLAT TW - ± 1. db - ± 1. db + ± 1. db - ± db LOW CUT SW: 100 Hz INPUT SIGNAL: 80 Hz REF: LOW CUT SW: FLAT - ± db INPUT SIGNAL: 100 Hz RESIDUAL NOISE LEVEL VR = MIN. DIN AUDIO Filter DIN AUDIO Filter TW < -8 dbu (NOTE): 0 dbu = 0.77 V 1
HS80M/HS0M HS0M INSPECTION HS0M 1. Test conditions (1) Input Signal: PHONE 1 khz (), 10 khz (TW) () Output load: ohms (), 8 ohms (TW) () AC power supply: AC100 V, 0/0 Hz (J) AC10 V, 0 Hz (U, T) AC0 V, 0 Hz (B, H, O) AC0 V, 0 Hz (K) AC0 V, 0 Hz (A) () VR-Level: MAX MID EQ SW: 0 ROOM CONTROL SW: 0 HIGH TRIM SW: 0 LOW CUT SW: FLAT. Specifications ITEM INPUT CONDITIONS OUTPUT CONDITIONS LIMIT 1 OUTPUT POWER 1 % THD OUTPUT TW > 1 W > 1 W GAIN INPUT: PHONE -10 dbu, 10 khz INPUT: PHONE -10 dbu, 1 khz TW ± dbu 17 ± dbu T.H.D. INPUT SIGNAL: 10 khz INPUT SIGNAL: 1 khz 8 W OUTPUT. W OUTPUT TW < 0. % FREQUENCY RESPONSE INPUT SIGNAL: khz INPUT SIGNAL: khz INPUT SIGNAL: 1 Hz REF: TW OUTPUT 10 khz 1 W REF: OUTPUT 1 khz 1 W TW - ± db - ± db 1. ± db MID EQ SW: - REF: MID EQ SW: 0 - ± 1. db MID EQ SW: + ROOM CONTROL SW: - INPUT SIGNAL: khz REF: ROOM CONTROL SW: 0 + ± 1. db - ± 1. db ROOM CONTROL SW: - TONE-CONTROL HIGH TRIM SW: - CHARACTERISTIC HIGH TRIM SW: + LOW CUT SW: 80 Hz INPUT SIGNAL: 00 Hz REF: HIGH TRIM SW: 0 INPUT SIGNAL: 10 khz REF: LOW CUT SW: FLAT TW - ± 1. db - ± 1. db + ± 1. db - ± db LOW CUT SW: 100 Hz INPUT SIGNAL: 80 Hz REF: LOW CUT SW: FLAT - ± db INPUT SIGNAL: 100 Hz RESIDUAL NOISE LEVEL VR = MIN. DIN AUDIO Filter DIN AUDIO Filter TW < -8 dbu (NOTE): 0 dbu = 0.77 V 1
POWERED MONITOR SPEAKER HS80M/HS0M CIRCUIT DIAGRAM CONTENTS BLOCK DIAGRAM... OVERALL CIRCUIT DIAGRAM... / HS80M... / HS0M... / Notation for Circuit Diagrams 1. How to identify inter-sheet connectors INPUT to page : I Signal name The page number indicates the destination page. This indicates the location of the counter inter-sheet connector. (The alphabet indicates horizontal direction and the number indicates vertical direction) Note: See parts list for details of circuit board component parts.
INPUT 1 1 INPUT INPUT (LF /) S H.P.F -1V LEVEL +1 8 + 1 + - IC101-1/ HIGH TRIM EQ VR1 IC10 / LOW CUT IC101-/ MID EQ ROOM CONTROL -1V +1 8 7 + 1 + 7 - STEP FILTER IC10-1/ IC10-/ LOW CUT IC10-/ -1V +1-1V +1 8 8-1 + 7-1 + 7 IC10-1/ IC10-/ IC10-1/ LOW CUT STEP FILTER LOW BOOST +1-1V +1 8 8 + 7 1 + + 7 - S IC10-1/ S1 S IC10-/ HIGH CUT -1V + 1-1V +1V IC10-1/ HF P LF CB101 P (S) CN0 HF LF AMP LIMITER -VCC (LF /) POWER AMP POWER AMP Q0~0 +VCC +VCC -VCC +VCC -VCC IC0 IC01 HF GND P LF GND CN01 TWEETER BLUE - + YELLOW WOOFER RED + - BLACK BLOCK DIAGRAM HS80M/HS0M AC INLET CN80 1 (S): Soldered! L80 (LF 1/) L801! F801! 1P (S) CN 1! C801 C810 POWER 1P (S) CN TRANS (LF /)! T801! S801 P (P) (S) CN80 P CN801 D01 P (S) P CN80 CN0 P P (S) CN80 CN0 R00 D801 R1 U1 +1V U -1V HS80M/HS0M
A B C D E F G H I J HS80M/HS0M 1 HS80M OVERALL CIRCUIT DIAGRAM 1/ (INPUT) 1 INPUT1 XLR INPUT LOW CUT INPUT PHONE LEVEL MID EQ khz + / 0 / -db ROOM CONTROL 0 / - / -db to AMP, TRANS, AC INLET CN0 (to Page 1 xx) D) LOW CUT STEP FILTER HIGH TRIM HIGH CUT STEP FILTER LOW CUT FLAT / 80 / 100Hz 1dB / oct MY: Mylar Capacitor 7 LOW BOOST Note: See parts list for details of circuit board component parts. 7
1 A B C D E F G H I J HS80M/HS0M HS80M OVERALL CIRCUIT DIAGRAM / (AMP, TRANS, AC INLET) 1 AMP POWER AMP REGULATOR +1V LIMITER WOOFER RED BLACK BLUE POWER AMP YELLOW TWEETER REGULATOR -1V Distination AC Cord J U, T H, A, K WG1700 WG1800 WG000 TRANS B O WG1900 WG00 POWER TRANSFORMER to INPUT CB101 (to Page I) LM88TF- (X7A00) POWER AMP AMP IC01, 0 POWER INDICATOR Distination J, U, T F801 WG8000 A 100 V, 10 V Distination J Transformer WG700 H, B, A, K, O WG8100 800 ma 0V U, T WG700 AC INLET POWER SWITCH Note: See parts list for details of circuit board component parts. Distination J, U, T H, B, A, K, O AC INLET WG700 WG900 H, B, O, K A WG700 WG7700 7 7
A B C D E F G H I J HS80M/HS0M 1 HS0M OVERALL CIRCUIT DIAGRAM 1/ (INPUT) 1 INPUT1 XLR INPUT LOW CUT INPUT PHONE LEVEL MID EQ khz + / 0 / -db ROOM CONTROL 0 / - / -db to AMP, TRANS, AC INLET CN0 (to Page 1 xx) D) LOW CUT STEP FILTER HIGH TRIM HIGH CUT STEP FILTER LOW CUT FLAT / 80 / 100Hz 1dB / oct MY: Mylar Capacitor 7 LOW BOOST Note: See parts list for details of circuit board component parts. 7
1 A B C D E F G H I J HS80M/HS0M HS0M OVERALL CIRCUIT DIAGRAM / (AMP, TRANS, AC INLET) 1 AMP POWER AMP REGULATOR +1V LIMITER WOOFER RED BLACK BLUE POWER AMP YELLOW TWEETER REGULATOR -1V Distination AC Cord J U, T H, A, K WG1700 WG1800 WG000 TRANS B O WG1900 WG00 POWER TRANSFORMER to INPUT CB101 (to Page I) LM88TF- (X7A00) POWER AMP AMP IC01, 0 POWER INDICATOR Distination J, U, T F801 WG700 1A 100 V, 10 V Distination J Transformer WG700 H, B, A, K, O WG800 00 ma 0V U, T WG800 AC INLET POWER SWITCH Note: See parts list for details of circuit board component parts. Distination J, U, T H, B, A, K, O AC INLET WG800 WG000 H, B, O, K A WG900 WG000 7 7
POWERED MONITOR SPEAKER HS80M/HS0M PARTS LIST CONTENTS OVERALL ASSEMBLY... / HS80M... HS0M... ELECTRICAL PARTS... / HS80M... HS0M... Notes: DESTINATION ABBREVIATIONS A : B : C : D : E : F : H : I : J : K : WARNING Australian model British model Canadian model German model European model French model North European model Indonesian model Japanese model Korean model Components having special characteristics are marked and specification equal to those originally installed. M : South African model O : Chinese model Q : South-east Asia model T : Taiwan model U : U.S.A. model V : General export model (110V) W: General export model (0V) N,X: General export model Y : Export model must be replaced with parts having The numbers QTY show quantities for each unit. The parts with -- in PART NO. are not available as spare parts. This mark } in the REMARKS column means these parts are interchangeable. The second letter of the shaded ( ) part number is O, not zero. The second letter of the shaded ( ) part number is I, not one.
HS80M/HS0M HS80M OVERALL ASSEMBLY HS80M Rear Panel Assembly Bonded 100 1 70 90 110 11 170 10 10 90 10 FUSE 10 80 8 SPACER 1 AC cord (ex. J) 0 10 0 0 10 0 0
HS80M/HS0M REF NO. PART NO. DESCRIPTION REMARKS QTY OVERALL ASSEMBLY HS80M -- Overall Assembly HS80M J J (7870) -- Overall Assembly HS80M U U (7880) -- Overall Assembly HS80M H H (7890) -- Overall Assembly HS80M B B (7900) -- Overall Assembly HS80M A A (7910) -- Overall Assembly HS80M K K (790) -- Overall Assembly HS80M T T (790) -- Overall Assembly HS80M CHN O (790) -- Service Parts Kits PA 8E0 (WG80) * 10 X79A00 Speaker.cm 8 OHM 9W TWEETER (08) * 0 WG1100 Hex.Socket Tapping Screw x0 (189) * 0 X70A00 Speaker 0cm OHM 8W WOOFER (18) * 0 WG000 Bind Head Tapping Screw x1 (1) * 0 WG700 Woofer Ring BLACK (07) * WG1100 Hex.Socket Tapping Screw x0 (189) * 0 WG700 Cord Assembly CORD SP (078) * 70 WG100 Knob Black LEVEL (10) * 80 WG00 Circuit Board HS80M AMP (WG0)(WG80) * 8 X7A00 IC LM88TF POWER AMP (0708) * 90 WG100 Bind Head Tapping Screw-S x1 (177) 8 * 100 WG00 Circuit Board HS80M INPUT (WG0)(WG80) * 110 WG100 Bind Head Tapping Screw-S x10 (10798) * 11 WH0000 Bonding Tapping Screw-B x10 (1770) * 10 WG00 Circuit Board HS80M TRANS (WG0)(WG80) s * 1 WG700 Transformer J J () s * 1 WG700 Transformer U/C,T U,T () s * 1 WG700 Transformer B,H,CHN H,B,O,K () s * 1 WG7700 Transformer A A (8) * 10 WG100 Bind Head Tapping Screw-S x10 (1079) s * 10 WG700 Circuit Board HS80M AC INLET J,U,T (WG0) s * 10 WG900 Circuit Board HS80M AC INLET H,B,A,K,O (WG80) * 10 WG100 Bind Head Screw x1 (8) * 1 WG000 Bind Head Tapping Screw x1 (1) 10 10 -- Cabinet Assembly (WG790) s * 170 WG00 Power Switch 81 POWER (81) RANK ACCESSRIES HS80M s * WG1700 AC Cord J J (17) s * WG1800 AC Cord U/C,T U,T (9) s * WG000 AC Cord H,A,K H,A,K (1797) s * WG1900 AC Cord B B (9) s * WG00 AC Cord CHN O (1) ELECTRICAL PARTS s * WG700 Circuit Board HS80M AC INLET J,U,T (WG0) s * WG900 Circuit Board HS80M AC INLET H,B,A,K,O (WG80) s * WG00 Circuit Board HS80M AMP (WG0)(WG80) * WG00 Circuit Board HS80M INPUT (WG0)(WG80) s * WG00 Circuit Board HS80M TRANS (WG0)(WG80) s * WG700 Circuit Board HS80M AC INLET J,U,T (WG0) s * WG900 Circuit Board HS80M AC INLET H,B,A,K,O (WG80) s * F801 WG8000 Fuse J.U. J,U,T (08991) s * F801 WG8100 Fuse 800MA S.B. H,B,A,K,O (0087) * WG00 Circuit Board HS80M INPUT (WG0)(WG80) * JK1 WG900 Cannon Type Connector JACK JY-0L 00 INPUT1 (1177) * JK WG000 Phone Jack JACK HTJ0-11D INPUT (0791) * VR1 WG100 Rotary Variable Resistor A 10K XVB1111NPD LEVEL (07) s * S801 WG00 Power Switch 81 POWER (81) : New Parts RANK: Japan only
HS80M/HS0M HS0M OVERALL ASSEMBLY HS0M Rear Panel Assembly Bonded 70 100 1 110 90 11 170 10 10 10 10 FUSE PLATE AC cord (ex. J) 80 8 10 1 0 10 0 0 10 0 0
HS80M/HS0M REF NO. PART NO. DESCRIPTION REMARKS QTY OVERALL ASSEMBLY HS0M -- Overall Assembly HS0M J J (7780) -- Overall Assembly HS0M U U (7790) -- Overall Assembly HS0M H H (7800) -- Overall Assembly HS0M B B (7810) -- Overall Assembly HS0M A A (780) -- Overall Assembly HS0M K K (780) -- Overall Assembly HS0M T T (780) -- Overall Assembly HS0M CHN O (780) -- Service Parts Kits PA 8E9 (WG0) * 10 X77A00 Speaker 1.9cm 8 OHM 19W TWEETER (07) * 0 WG1100 Hex.Socket Tapping Screw x0 (189) * 0 X78A00 Speaker 1cm OHM 8W WOOFER (0) * 0 WG000 Bind Head Tapping Screw x1 (1) * 0 WG00 Woofer Ring BLACK (07) * WG1100 Hex.Socket Tapping Screw x0 (189) * 0 WG00 Cord Assembly CORD SP (077) * 70 WG100 Knob Black LEVEL (10) * 80 WG00 Circuit Board HS0M AMP (WG0)(WG90) * 8 X7A00 IC LM88TF POWER AMP (0708) * 90 WG100 Bind Head Tapping Screw-S x10 (10798) * 100 WG00 Circuit Board HS0M INPUT (WG0)(WG90) * 110 WG100 Bind Head Tapping Screw-S x10 (10798) * 11 WH0000 Bonding Tapping Screw-B x10 (1770) * 10 WG00 Circuit Board HS0M TRANS (WG0)(WG90) s * 1 WG700 Transformer J J (0) s * 1 WG800 Transformer U/C,T U,T (1) s * 1 WG900 Transformer B,H,CHN H,B,O,K () s * 1 WG000 Transformer A A (8) * 10 WG100 Bind Head Tapping Screw-S x10 (1079) s * 10 WG800 Circuit Board HS0M AC INLET J,U,T (WG0) s * 10 WG000 Circuit Board HS0M AC INLET H,B,A,K,O (WG90) * 10 WG100 Bind Head Screw x1 (8) * 1 WG000 Bind Head Tapping Screw x1 (1) 10 10 -- Cabinet Assembly (WG0) s * 170 WG00 Power Switch 81 POWER (81) RANK ACCESSRIES HS0M s * WG1700 AC Cord J J (17) s * WG1800 AC Cord U/C,T U,T (9) s * WG000 AC Cord H,A,K H,A,K (1797) s * WG1900 AC Cord B B (9) s * WG00 AC Cord CHN O (1) ELECTRICAL PARTS s * WG800 Circuit Board HS0M AC INLET J,U,T (WG0) s * WG000 Circuit Board HS0M AC INLET H,B,A,K,O (WG90) * WG00 Circuit Board HS0M AMP (WG0)(WG90) * WG00 Circuit Board HS0M INPUT (WG0)(WG90) * WG00 Circuit Board HS0M TRANS (WG0)(WG90) s * WG800 Circuit Board HS0M AC INLET J,U,T (WG0) s * WG000 Circuit Board HS0M AC INLET H,B,A,K,O (WG90) s * F801 WG700 Fuse 1 J.U. J,U,T (91) s * F801 WG800 Fuse 00MA S.B. H,B,A,K,O (071) * WG00 Circuit Board HS0M INPUT (WG0)(WG90) * JK1 WG900 Cannon Type Connector JACK JY-0L 00 INPUT1 (1177) * JK WG000 Phone Jack JACK HTJ0-11D INPUT (0791) * VR1 WG100 Rotary Variable Resistor A 10K XVB1111NPD LEVEL (07) s * S801 WG00 Power Switch 81 POWER (81) : New Parts RANK: Japan only