7 7
Phoenix BIOS 4.0 Release 6.0.XXXX : CPU=Pentium III Processor XXX MHz 0640K System RAM Passed 0127M Extended RAM Passed WARNING 0212: Keybord Controller Failed. : Press <F1> to resume, <F2> to setup 0200 Failure Fixed Disk 0210 Stuck Key 0211 Keyboard error 0212 Keyboard Controller Failed 0213 Keyboard locked - Unlock key switch 0230 System RAM Failed at offset 0231 Shadow RAM Failed at offset 0232 Extended RAM Failed at address line 0233 Memory type mixing detected 0250 System battery is dead - Replace and run SETUP 0251 System CMOS checksum bad-default configuration used
0252 Password checksum bad - Password cleared 0260 System Timer error 0270 Real time clock error 0271 Check date and time setting 02D0 System cache error - Cache disabled 02D1 System Memory exceeds the CPU's caching limit 0613 COM A configuration change 0614 COM A config, error - device disable 0B28 0B29 0B60 0B61 0B62 0B70 0B71 0B74 0B75 0B80 0B81 0B82 0B83 Unsupported Processor detected on Processor 1 Unsupported Processor detected on Processor 2 DIMM group #1has been disabled DIMM group #2 has been disabled DIMM group #3 has been disabled The error occurred during temperature sensor reading System Temparature out of the range The error occurred during voltage sensor reading System voltage out of the range BMC Memory Test Failed BMC Firmware Code Area CRC check failed BMC core Hardware failure BMC IBF or OBF check failed
0B8A BMC SEL area full 0B8B 0B8C 0B8D 0B8E 0B8F 0B90 0B91 0B92 0B93 0B94 0B95 0B96 BMC progress check timeout BMC command access failed Could not redirect the console - BMC Busy Could not redirect the console - BMC Error Could not redirect the console - BMC parameter Error - BMC Platform Information Area corrupted BMC update firmware corrupted Internal Use Area of BMC FRU corrupted BMC SDR Repository empty IPMB signal lines do not respond BMC FRU device failure BMC SDR Repository failure 0B97 BMC SEL device failure 0B98 BMC RAM test error 0B99 BMC Fatal hardware error 0B9A BMC not responding 0B9B 0B9C 0B9D Private I2C bus not responding BMC internal exception BMC A/D timeout error 0B9E SDR respository corrupt
0B9F SEL corrupt 0BA0 0BB0 0BB1 0BC0 0BC1 SDR/PIA mismatched. SDR, PIA must be updated. SMBIOS - SROM data read error SMBIOS - SROM data checksum bad POST detected startup failure of 1st Processor POST detected startup failure of 2nd Processor 8120 Unsupported DIMM detected in DIMM group #1 8121 Unsupported DIMM detected in DIMM group #2 8122 Unsupported DIMM detected in DIMM group #3 8130 Mismatch DIMM detected in DIMM group#1 8131 Mismatch DIMM detected in DIMM group#2 8132 Mismatch DIMM detected in DIMM group#3 8150 NVRAM Cleared By Jumper 8151 Password Cleared By Jumper 8160 Mismatch Processor Speed detected on Processor 1 8161 Mismatch Processor Speed detected on Processor 2 8170 Processor 1 not operating at intended frequency 8171 Processor 2 not operating at intended frequency 9064 Mixed CPU Steppings detected
9038 Check date and time settings (Chipset) 9001 Missing date and time synchronization 9002 Memory not installed. 9003 Memory implementation error detected 9004 Real time clock error (Chipset) 9005 Remote BMC access failed. 9006 HW Memory Test failed. 9009 Chipset NMI occurred! 900A PEXA Link Width Warning 900B PEXB Link Width Warning 900D PEXD Link Width Warning 900E PEXE Link Width Warning 9021 Trace memory test failed 902C BMCFW major revision mismatched. 902D 902E IPMB#1 SROM failure detected. IPMB#2 SROM failure detected. 902F PCI Device Test failed. 9060 Module#0 is not present. 9061 Module#1 is not present. 9039 Not keep last boot order. 9070 The error occurred during water-cooling unit sensor reading NOTI- CE System is force boot with POST error
STOP : C000021A (FATAL SYSTEM ERROR) The Windows logon process.. System process terminated. Unexpectedly with a status of 0x00000001 (0x00000000 0x00000000). The system has been shutdown. crashdump : initializing miniport driver crashdump : dumping physical memory to disk
w w
w w