p01.pdf

Before commencing assembly, please read these instructions thoroughly! R THE FINEST RADIO CONTROL MODELS Radio Controlled. Engine Powered Racing Car Series INSTRUCTION MANUAL INDEX REQUIRED FOR OPERATION RADIO PREPARATION BEFORE YOU BEGIN ARRANGEMENT OF PLASTIC PARTS ON RUNNERS ASSEMBLY OPERATING YOUR MODEL SAFELY EXPLODED VIEW SPARE PARTS & OPTIONAL PARTS 3 3 5 6 7 5 6 7 8 3 SAFETY PRECAUTIONS This radio control model is not a toy. First-time builders should seek the advice of experienced modellers before commencing assembly and if they do not fully understand any part of the construction. Assemble this kit only in places out of children's reach! Take care before operating this model. You are responsible for this model's assembly and safe operation! Always keep this instruction manual ready at hand for quick reference, even after completing the assembly. SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE. No. 30 00 KYOSHO

RECHARGEABLE Ni-Cd BATTERY KYOSHO CORPORATION NO.790 R R REQUIRED FOR OPERATION () ch radio control set with servos. This kit requires a channel radio con-trol set with servos. Because there are stick-type and wheel-type transmitters, use which ever fits your convenience best. In case of using reverse switch, refer to instruction manual included in the radio set. Stick-type ch radio set. Wheel-type ch radio set. AA-size Batteries (For Transmitter) AA AA Ni-Cd Battery Only use No.76 6V X-FOURCE 600 Ni-Cd Battery. (Do not use other batteries.) Suitable servos & receiver Servo Receiver Engine & Muffler This kit requires a. class engine. *Only SG Shaft (Pilot Shaft) with Slide Carburettor engine without pull starter is available. Engine for. class cars Plug Muffler Joining Pipe Manifold No.3905 No.3905 No.3905 Tuned Silencer Set (Side) or, No.3905 Tuned Silencer Set (Rear) 3 Required for engine starting: Glow Fuel Glow Engine Fuel Fuel Pump Plug Heater Paint For painting the body, use Kyosho paints for models! No.60700 RC No.96 No.96 Quick Fill Fuel Bottle One-touch Plug Heater Set No.30 POLYCA COLOR Plug Wrench Starter Battery No.7650 767 KYOSHO SPRAY COLOR No.803 No.3977 Locking Jig & Wrench Multi Starter Box No.70 X - Force 00 Ni-Cd Battery KY OSH O S PR AY CO LO R KY OSH O S PR AY CO LO R 5 Other equipment required. Air Filter Tape Tire setter

REQUIRED FOR OPERATION () 6 Tools required Phillips Screwdriver (L.M.S) Needle Nose Pliers Instant Glue Sharp Hobby Knife Wire Cutters Screw Cement Box Wrench Awl Pliers Rubber Cement TOOLS INCLUDED Hex Wrench Cross Wrench (S) Grease Grease No.803 SPECIAL TAPER REAMER No need to pre-drill! Drills neat mm to 5mm holes directly! No.89 ROUND CUTTER & SANDER For trimming bodies! Cutting along curved lines never was so easy! Set up the radio control system as indicated below. RADIO PREPARATION 3 5 6 7 8 9 0 START FINISH 8 3 5 6 7 8 9 0 Install batteries. (Transmitter) Extend the antenna. (Transmitter) Connect the charged Ni-Cd battery to the receiver. Extend the antenna. (Receiver) Center the trims. Switch on. (Transmitter) Switch on. (Receiver) Make sure the servos are in command. Switch off. (Receiver) Switch off. (Transmitter) Retract the antenna. (Transmitter) 5 6 7 3 3

3 BEFORE YOU BEGIN Read through the manual before you begin, so you will have an overall idea of what to do. Check all parts. If you find any defective or missing parts, contact your local dealer or our Kyosho Distributor. How to read the instruction manual: Front Suspension 5 x 0mm Metal Bushing No., No.5, No.6 Example 3 5 This instruction manual uses several symbols. Please note them during the entire assembly. 5 King Pin 6 7 6 5.8mm Pillow Ball (Black) Key Number, Part Name, True-to-scale Diagram, Quantity Used All parts except screws are identified by key numbers. For purchasing spare parts, find the key no. of the part needed in the spare part list and refer to the left column to look up the corresponding order no. R 5 8 L 5 Symbols used throughout the instruction manual, comprise: Apply instant glue (CA glue, super glue). Apply rubber cement. Apply threadlocker (screw cement). mm Assemble left and right sides the same way. Drill holes with the specified diameter (here: mm). Cut off shaded portion. Apply grease. x True-to-scale diagram. Must be purchased separately! Pay close attention here! Assemble as many times as specified (here: twice). Ensure smooth non-binding movement while assembling. Tentatively tighten. Assemble in the specified order. This kit contains screws and hardware in different metric sizes and shapes. Before using them, check the screws on the true-to-scale diagrams on the left side in each assembly step. Some screws are extras. SCREWS Screw Self-tapping (TP) Screw OTHER HARDWARE Screw Washer Nut E-ring Cap Screw Flat Head (F/H) Screw TP F/H Screw mm F/H Screw 3mm 3mm 3mm Metal Bushing Bearing 5mm mm Pillow Ball mm 0mm 5.8mm 6 Self-tapping (TP) screws cut threads into the parts when being tightened. Excessive force may permanently damage parts when tightening TP screws. It is recommended to stop tightening when the part is attached or when some resistance is felt after the threaded portion enters the plastic. Correct Wrong Overtightened. The threads are stripped.

ARRANGEMENT OF PLASTIC PARTS ON RUNNERS Shaded Parts are not used. 9 86 9 87 95 85 93 88 89 90 9 3 3 3 5 6 3 3 33 33 33 33 5

ARRANGEMENT OF PLASTIC PARTS ON RUNNERS Shaded Parts are not used. 79 80 8 83 8 8 6 0 9 7 55 9 5 5 5 53 50 9 7 88 76 90 9 9 96 93 9 96 95 89 6

Gear Differential No. 5 63 7 9 8 8 6 8 5 < > < For Rear > 3 7 9 8 7 9 OP5 O-ring P5 9 63 5 x mm Pin 7 x 0mm Shim 8 5 x mm Shim 6 5 7 5.6 x 8mm TP TP F/H Screw 50 x 7mm Shaft 63 Differential Joint 5 7 5 50 5 7 Silicone Oil (Hard).6x8mm.6x8mm 63 Pour Silicon Oil (Hard) included in the kit. Front Oneway No., No., No.3 9 Apply Instant Glue. x 8mm Screw 76 Front Oneway Collar 66 30 9 Note the direction. 67 Cup Joint 56 x 8mm Ball Bearing 67 76 56 30 9 x8mm 56 76 67 Apply threadlocker (screw cement). Apply instant glue (CA glue, super glue). 7

3 Steering No., No.3, No.0 3.5mm approx. 3.5mm HITEC FUTABA KO JR SANWA 95 93 9 H Serrated Cap (H) F Serrated Cap (F) KJS Serrated Cap (KJS) 98 7 The Side with groove is reverse screw. 3mm 9 0 x 98 0 3mm 7 Nylon Nut Steering Rod 98.8mm Ball End (Medium) 0.8mm Ball Stud Front Bulkhead No., No.3, No.0 x8mm Steering Front Oneway 77 Front Belt 0.5mm approx. 0.5mm x8mm 3 x mm TP TP F/H Screw x 8mm 3xmm 3xmm x Assemble as many times as specified. True-to-scale diagram. 8

5 Front Suspension Arm 3 x 3mm 3 x mm 3 x 5mm F/H Screw x 8mm 0.8mm 0 5.8mm Ball Stud Flange Ball 55 6 x mm Ball Bearing No., No.3, No.0 3x3mm 99 3x5mm < > 03 3mm < Right > 5 0 x 5mm F/H Washer Ball Bearing 6mm 00 9mm Pillow Ball Nut 6 Wheel Shaft (Front) (Black) 03 85 87 6 x8mm 0 5.5mm approx..5mm 6 < > < Left > 7 0 3xmm 55 3 5 00 99 3.mm Note the direction. 99 00 3 5mm Hex Wrench (5mm) mm mm Flanged Nylon Nut 99 9mm 5 x mm Pin Pillow Ball 86 00.5mm Hex Wrench (.5mm).7mm 6 Front Suspension Arm 3x3mm No.3, No.0 75 For Right 7 3x3mm 75 5 E.5 E.5 3 x 3mm 7 3 6 0 9 E.5 E E-ring 6 Swing Shaft (Front) For Left 5 OP3 O-ring P3 (Red) 75 3 x 7mm Shaft 7 3 x 7mm Shaft Ensure smooth, non-binding movement when assembling. Assemble left and right sides the same way. Assemble in the specified order. Tentatively tighten. Apply grease. Apply threadlocker (screw cement). 9

7 Bumper No., No.3, No.0 3 x 0mm 3 x 0mm TP TP Screw F/H Screw 3 3mm Nylon Nut 3 3 x 8mm TP TP F/H Screw 8 8 8 8 3x8mm 80 3mm 3x0mm 3x0mm(F/H) 79 8 Rear Bulkhead 6 Brake Piston No., No., No.0 66 6.5mm approx. 6.5mm 66 Brake Shaft 3 x 5mm Cap Screw Note the direction. Top 6 5 5 3x5mm 9 Rear Bulkhead No., No. 5 Cut off. 9T Pulley 5 x mm Pin 6 3 5 6 Spur Gear Shaft 9 "9" Inscription Apply rubber type glue. 0

0 Rear Bulkhead No., No., No.0 x8mm 55 79 Belt (Small) 3 x 8mm 3 x mm TP TP F/H Screw 5 x mm Pin E5 E E-ring 56 x 8mm Ball Bearing 55 6 x mm Ball Bearing 3 3xmm 56 3 3xmm 56 55 Assy Rear Differential Assembly 6 5 Tighten up to the end. x8mm 9 "9" Inscription E5 Rear Suspension Arm 3 x mm x 8mm 3 x 5mm Cap Screw 55 6 x mm Ball Bearing 5 0 x 5mm Ball Bearing.5mm approx..5mm 6x8xmm Aluminium Collar mm Flanged Nylon Nut No., No., No.0 x8mm The side with the step is a reverse screw. x 90 For Right 89 For Left 0 0 88 0 3xmm 5mm approx. 5mm Insert from wider side. < > < Left > 3x5mm 5 x mm Pin 88 6.8mm Wheel Shaft (Rear) (Silver) Ball End 0 x0mm 00 9mm Adjustable Rod Pillow Ball Nut 6 0 6.8mm Flange Ball 99 9mm Pillow Ball 0 5.8mm Flange Ball 5 L 99 Marked L R Marked R < > < Right > 55 99 3.5mm Hex Wrench (.5mm) 5 0.5mm 5 00 mm.3mm 5mm Hex Wrench (5mm) 00 Ensure smooth, non-binding movement when assembling. x Assemble left and right Assemble as many sides the same way. times as specified. True-to-scale diagram. Assemble in the specified order. Tentatively tighten. Apply threadlocker (screw cement).

Rear Suspension Arm No., No., No.0 3x0mm For Right 3 x 0mm 3 x mm TP TP Screw TP TP F/H Screw 3x0mm 9 3 x 0mm Cap Screw 3 3 Swing Shaft (Rear) 3xmm 76 3 x 59mm Shaft 76 For Left 3 Speed Changer No.5, No.0 x mm.6 x mm Cap Screw 5mm Roller 0.6 x 3 x 5.5mm Collar 9 Speed Spring.6xmm 0 9 8 3.6xmm 5 xmm Firmly tighten the set screws onto the flat spots. 0.6mm 0 3 Tighten.6mm Cap Screw to 0 Collar till the screw stops, and unscrew 3 rounds, then please set up according to the track condition. 8 9 0.6xmm Part bags used. Apply threadlocker Apply grease. Assemble left and right (screw cement). sides the same way. Assemble in the specified order. Ensure smooth, non-binding movement when assembling.

Speed Changer No.5, No.0 3 x 6mm F/H Screw 3 3 x 0mm Cap Screw 55 6 x x mm Ball Bearing 3 3 x mm Washer 3 x 8 x mm Collar 3x6mm 55 55 3x6mm 7 3 6 Note the direction. 3x0mm 5 Middle Shaft Support 3 x mm TP TP F/H Screw No.6, No.0 5 3xmm 3xmm 3

6 Middle Shaft Support 5 x mm E5 Pin 55 6 x mm Ball Bearing E E-ring 6 No., No.6, No.0 3 E5 55 E5 6 8 "8" Inscription 8 5 Front Belt 8T Pulley 5 3 0 5T Pulley 55 7 5 5 "5" Inscription 65 65 Middle Shaft 55 8 96 97 5 0 E5 78 Middle Belt 5 "5" Inscription 9 7 Center Bulk No., No.6, No.0 3 x mm TP TP F/H Screw 5 5 Front Note the direction. 5 3x0mm 37 3x0mm 3 x 0mm TP TP Screw 5 3xmm 3xmm Assemble in the specified order.

8 Engine No.7 0 7 x mm Washer 0 SG For Side Exhaust, SG shaft (Pilot shaft) type. In case of no space as shown, insert the washer included in the kit. 09 98 07 09 08 mm 9 8 06 7 9 Engine No.7, No.0 3x0mm (Cap) 3x0mm (Cap) 3 x 0mm 3 x mm 3 x 5mm Cap Screw Cap Screw Cap Screw 5 Bell Guide Washer 58 5 x 0 x mm Ball Bearing Engine Assembly 0.5mm 0 0.5mm 0 5x0.mm 5x0.5mm 3x0. mm Adjust 0 5x0.mm, 5x0.5mm and 3x0.mm so that this space to be 0.5mm (Refer to the Setting Sheet). 05 58 6 58 3 08 08 08 5 0 08 3xmm 3x5mm Select according to the engine you use. O.S. Marked O.S. 08 Cut off shaded portion if it is needed. Must be purchased separately! Apply threadlocker (screw cement). 5

0 Engine No.6, No.0 Engine Assembly V-One R 3905 39053 In case of Side Exhaust engine, No.3905 Tuned Silencer or No.39053 Manifold. Tighten the screws with one sheet of paper inserted b etween both gears. 7 Not use for Rear Exhaust engine. 3x0mm 3x8mm (TP F/H) 3 x 8mm Screw 3 x 8mm TP TP F/H Screw 3x8mm 3x8mm 3 x 0mm TP TP Screw Muffler 3 x 0mm F/H Screw 3 x 3mm No.7, No.0 3x3mm 0 Bend the wire to adjust the muffler. Nylon Strap 3x0mm Must be purchased separately! 6

No.8 Front Shock 3 5.8mm Shock End 38 A.6mm Shock Collar (A) Nylon Nut 33.6mm 35 3 3 36 0 30A 5mm 35 39 C Shock Piston C-ring 37 O.6mm O-ring (Blue) Washer 37 38 39.6mm 3 3 Silicone (Soft) x.5mm 3 Front Shock 30B (Black) No.8 8 For Front (Short) x No.8 Rear Shock 3 5.8mm Shock End 38 A.6mm Shock Collar (A) Nylon Nut 33.6mm 35 3 3 36 0 30A 6.5mm 35 39 C Shock Piston C-ring 37 O.6mm O-ring (Blue) Washer 37 38 39.6mm 3 3 Silicone (Soft) x mm 5 Rear Shock No., No.8 9 (Blue) 83 30B Do not use the 30B! For Rear (Long) x x Assemble as many times as specified. 7

6 Front Shock Stay 3 x 0mm 0 5.8mm Flange Ball No., No.8, No.0 83 3x0mm 0 Front Shock 7 Rear Stabilizer No., No.6, No.0 3 x 3mm 6 5.8mm Ball Stopper 3 x mm 98.8mm Ball End (Medium) 3x8mm 3 x 8mm Screw 3x0mm.8mm S 3 x 0mm Ball Stud (S) Cap Screw 7 5.8mm 3 x 6mm Ball End Flanged Cap Screw 03 9 3x0mm 7 73 mm 3xmm 0mm x 98 3x3mm 78 3x6mm 0 Apply threadlocker (screw cement). x Assemble left and right Assemble as many sides the same way. times as specified. True-to-scale diagram. 8

8 Rear Shock Stay 9 No., No.0 Note the direction. 3x0mm 93 3x0mm 3x0mm 3x0mm 3mm 93 95 3x0mm 3mm 3 x 0mm TP TP Screw 3mm 3 x 0mm Screw 3mm Nylon Nut 3mm 9 Rear Shock 3 x mm 0 5.8mm Flange Ball No., No.0 3xmm 0 0 3xmm Rear Shock Apply threadlocker (screw cement). Ensure smooth, non-binding movement when assembling. 9

30 Fuel Tank No.6, No.9, No.0 3 x 5mm F/H Screw Pull the Nylon Strap to open the tank. Note the direction. 9 3mm (Nylon) 3mm 3mm (Nylon) 9 56 50 60 63 Nylon Straps (Mid size) 3mm Nylon Nut 3mm Nut 3x5mm 3x5mm 3 Servo Saver No., No.0 3xmm (TP) 3xmm (TP) 3 x mm TP TP Screw 6 Note the direction. 33 Set up according the servo you use. 3 x 8mm Screw 3 x 0mm Screw 33 Throttle Control Servo Note the direction. 33 33 33 Insert Rubber Grommet into Both Servo. 3xmm (TP) Steering Servo 3x8mm3x0mm Depending on Servo, select 3x8mm or 3x0mm. 3 Roll Bar No.6, No.0 53 Note the direction. 3 x 0mm TP TP Screw 53 Front 3x0mm 3x0mm Must be purchased separately! Apply threadlocker (screw cement). 0

33 Belt Tensioner No., No.9, No.0 E 3x3mm xmm 3 x 3mm x mm 57 57 07 E E E-ring 88 06 3 Battery No. 90 Suitable Battery KYOSHO 76 X-FORCE 6V-600 KYOSHO 76 X-FORCE 6V-600 Ni-Cd Battery 90 Fix with Glass Tape, etc. Attach Glass Tape around while holding the battery and 90 on flat place. Battery 8.5mm Battery of over 8.5mm width cannot be used. 35 Radio Plate No.0 3x0mm 3 x 0mm TP TP Screw 3 x 8mm TP TP F/H Screw Belt Tensionner 3x8mm (TP F/H) Battery Must be purchased separately!

36 Receiver No., No.9 Come with radio. 89 Connect as per radio instruction manual. 6 Use 6 Nylon Strap (Small) to keep cords away from moving parts. 89 Receiver Switch 63 Nylon Strap (Middle) Receiver Attach on the corner. / 37 Throttle Servo / Radio 57 No.9, No.0 3x5mm (TP) 5 5 3x5mm (TP) 73 7 Thread antenna cord through. 5 5 3 x 5mm TP5 OP3 TP Screw O-ring P3 (Red) 38 Radio Plate No.0 3x8mm 3x0mm 3 x 8mm TP TP F/H Screw 3 x 0mm TP TP Screw 3x0mm 3x0mm 3x8mm Set up according the servo you use..6 x 0mm Cap Screw 3 x 0mm Cap Screw.6x0mm 3x0mm Set up according the servo you use. Must be purchased separately! Apply instant glue (CA glue, super glue).

39 Fuel Tube No.9 0 50 00mm 53 90mm Silicone Tube (90mm) 53 0mm Silicone Tube (0mm) 0 Linkage.6 x 5mm 9 mm Screw 3 x 3mm 6 Throttle Brake Spring 9.6mm Nylon Nut.6mm Nut 9 No.3, No.9, No.0 3x3mm Stopper 9 5.6x5mm 96 6 9.6mm Servo Horn.6mm (Nylon) 3x3mm.6x5mm 3 53 96 Cut off the fuel tube 0mm..6mm Linkage 3 x 3mm No.9, No.0 Come with radio. Air Cleaner 3x3mm 8 Must be purchased separately! Ensure smooth non-binding movement while assembling. 3

Wheels < > < Rear > 30mm < > < Front > 6mm 7 75 mm Remove when adjust. 3 Body Shell 65 Body Pin No., No.0 65 65 6mm 6mm 6mm 65 Drill holes for muffler tail pipe. Safety Precautions Always run your car with the body shell fitted! Avoid changing the running direction too often and too abruptly. Do not run your car on ground: that is overgrown with grass. that is muddy, sandy or rocky. Check all screws, nuts etc. on a regular basis for looseness. Assemble left and right sides the same way. Cut off shaded portion. 6mm 6mm Drill holes with the specified diameter.

OPERATING YOUR MODEL SAFELY In order to avoid accidents and personal injury, be sure to observe the following: Since exhausts and fuel vapors are noxious to health, use fuel only outdoors! Keep hands and objects away from rotating engine parts to avoid personal injury. Because after running the engine, the engine and the muffler are extremely hot, beware of getting burned! For accident prevention, do not run your model under Only use glow fuel for radio control models! Never use the following circumstsnces: gasoline or kerosene which might cause accidents such as fires! In place where many people gather. Near residential districts, schools and hospitals. Because fuel is highly inflammable, never use fuel indoors, near any source of heat, open flames or even Near roads, railroads, air corridors and electric lines. sparks! Do not dispose of an empty fuel can into a fire. It might explode causing serious injury! Also make sure that nobody is using the same frequency as you do at the same time! Be particularly careful not to swallow fuel or to get fuel When the radio batteries are empty. into eyes! Nevertheless, should fuel be swallowed, immediately induce vomiting and call a physician. Should fuel get into eyes, thoroughly rinse the eyes and seek medical advice. Always store fuel in a safe place out of children's reach with the cap shut tight! The place for storage should be dark, cool and dry! When the model's control or running behavior is strange. 5

< EXPLODED VIEW > 3 VZ00 08 VZ095 8 FM33- 一部パーツ販売していないパーツがあります FM37 Parts indentified only by key numbers are not sold individually! 96 FM37C 9 VZ007 9 VZ007 5 FM37 58 96996 FM38-66 VZ00 53 VZ060 9 VZ060 33 VZ00 33 55 967 73 95 90 VZ083 J N G 0 9 55 967 60 VZ06 76 56 9659 F VZ086 93 9 95 73 708 7 708 0 UM8 63 70KP/KY 86 VZ083 VZ00 D 00 VZ08 5 W508 8 8 VZ08 7 VZ068 K 0 W058 75 VZ07 C 35 80 6 37 6 85 0 W058 VZ008B 03 W06 76 VZ08 3 VZ00 3 VZ080 55 967 5 VZ060 76 FM3 89 VZ083 0 VZ077 F H 99 FZ7 D 6 I 88 VZ083 VZ08 VZ008B 5 9699 0 W05 55 967 VZ00 L 55 967 L A 3 W505 M 5 905 5 67 VZ079 00 FZ75 7 3 W505 73 95 98 UM 78 UM9 L I 9 83 VZ073-06 7 9053 97 99 FZ7 00 FZ75 VZ083 30B 0 VZ085 3 VZ005 8 VZ07-307 00 KYOSHO / 禁無断転載複製 VZ008B 55 VZ060 7 VZ003 87 3 9 VZ083 78 VZW06 VZ009 56 9659 5 9699 VZ05 7 VZ060 VZ003 0 3 O 56 9659 77 VZW0 7 VZ06 38 39 3 A 0 UM8 VZ075 79 VZ08 5 905 38 39 3 3 VZ009 63 37 93 VZ083 M 96 33 K N 9 905 VZ075 33 03 VZ088 5 905 5 3 5 905 99 VZ08 B P 55 967 65 VZ06 98 UM 3 95 VZ083 9 VZ083 VZ0 9 7 35 VZ009 6 VZ0 9 3 VZ09 3 5 5 79 VZW0 VZ03 6 8 6 VZ063 30 6 VZ0 50 5 VZ060 66 VZ078 76 FM3 VZ00 50 VZ0 8 9 30A 36 65 9638 7 0 W058 93 VZ083 5 BS07 E 0 VZ075 5 7 36 O 9 VZ083 VZ087 55 967 56 9659 83 VZ08 6 VZ008B 67 VZ079 7 8 5 905 6 98 UM 75 VZ07 9 5 9696 3 VZ03 30A VZ0 5 FM37C B 9 905 VZ0 9 0 VZ075 0 W058 5 905 9985 90 FM3 P L 5 5 9696 6 VZ00 H 0 7 VZ009 63 VZ05 57 VZ06 5 W508 5 W508 89 FM3 8 08 FD0 5 FM36 FM360 VZ00 VZ005 7 FM35 G 07 06 E 0 UM3 3 FM357-0H 76 VZ08 57 FM37 5 W508 8 FM35 FM360 FM356-6L 57 VZ00 09 UM3 9 FM353 8 9 0 78 UM9 88 FM3 33 58 96996 06 VZ093 50 VZ060 37 VZ0 09 VZ096 05 VZ09 5 FM358 966 55 967 FM358 0 FM358 7 FM363-H 6 96995 9 808 J 07 VZ09 FM359 6 VZ006 9 808 96 FM37C 98 VZ09 VZ090 3 FM38-56 9050 6 FM37 53 790 6 FM36-8L 53 790 0 W058 99 FZ7 00 FZ75 5 VZ006 99 FZ7 C 00 FZ75 3 VZ00 75 3 VZ00 VZ08 VZ076 V-One RR 7

No. Part Names No. Quantity VZ00 Front Bulkhead x VZ00 Rear Bulkhead 3 x VZ003 Front Suspension Arm Set 6 7 0 x 9 x VZ00 Rear Suspension Arm Set x VZ005 VZ006 VZ007 VZ008B VZ009 VZ00 VZ0 VZ0 VZ03 VZ0 VZ05 VZ06 VZ07 VZ08 VZ09 VZ00 VZ0 VZ03 VZ060 VZ06 VZ06 VZ063 VZ06 VZ068 VZ07-57 VZ07-307 VZ07-357 VZ073-356 VZ073-06 8 Front Knockle Arm 3 x Rear Upright 5 6 x Bumper 9 x 3 96 97 x Pulley Set x 6 x 3 9 30 3 x Differential Pulley Set 7 8 x.6x8mmtp.6x8mm TP Flat Head Screw x 8 x8mmtp x8mm TP Bind Screw x Drive Washer Set 3 33 x 3 x Shock Stay Set 37 x Differential Gear Set 6 8 9 x 5 7 x 8 Wheel Shaft 6 5 x Swingshaft 6 x Differential Joint 63 5 x Front Lower Suspention Shaft 7 x E E.5 E-ring (E.5) x Front Upper Suspention Shaft 75 x Rear Lower Suspention Shaft 76 x Front Suspension Plate 3 x Brake Shaft Set 66 6 x Differential Packing Brake Disk 8 x 5 3 x V-One R7 50 5 Center Parts (for V-One R) 5 53 5 55 V-One R Crystal Cap (for V-One R) 57 x V-One R Upper Plate (for V-One R) 60 x V-One R nd Gear Main Shaft (for V-One R) 6 x V-One R Middle Shaft (for V-One R) 65 x 5 Adjustable Rod (5) 7 x x 9 x.5x.7 Front Spring (.5x.7) Gold 3x.7 Front Spring (3x.7) Black 3.5x.7 Front Spring (3.5x.7) Silver 3.5x.6 Rear Spring (3.5x.6) Gold x.6 Optional Parts (Hard) x 8 x SPARE PARTS () Optional Parts (Soft) x Optional Parts (Hard) x 500 00 500 600 600 500 500 00 600 700 00 500 900 600 600 600 00 00 00 00 700 00 500 00 00 00 00 Rear Spring (x.6) Black 83 x 00 VZ073.5x.6 x -56 Rear Spring (.5x.6) Silver Optional Parts (Soft) 00 VZ075 V-One 9 3 3 33 3 35 36 V-One Shock 38 0 x 30A 30B x 39 x 3 37 x Instruction Manual VZ076 V-One R Main Chassis (for V-One R) x 3500 VZ077 0 Upper Rod (0) 0 x 00 FOR JAPANESE MARKET ONLY. No. No. Part Names Quantity VZ078 Front Oneway Shaft x8mm x8mm Bind Screw x 000 00 VZ079 Cup Joint 67 x 600 VZ080 Swingshaft (Wide tyres) 3 x 600 VZ08 Wheel Shaft (Wide tyres) x 700 VZ08 79 80 83 8 x Wide Bumper Set 8 8 x 500 85 86 89 90 9 9 9 VZ083 Rear Body Mount Parts 95 x 87 88 93 x 700 VZ08 Front Stabilizer Set 99 00 x VZ085 Rear Stabilizer Bar Set 0 x 800. Rear Stabilizer Bar (ø.) x.6 Rear Stabilizer Bar (ø.6) x VZ086 Muffler Stay Holder 0 x 3x3mm 3x3mm x 00 3x0mm 3x0mm Flat Head Screw x VZ087 Muffler Stay x 3 VZ088 Body Mount Post 03 x V-One RR VZ089 Decal Set (V-One RR) 8 x 800 VZ090 3D ASSY 09 0 05 06 07 08 09 3D Clutch Assembly 5 7 8 9 x 6500 58 0 x 98 x 3 x 6 x set 3xmm 3xmm Cap Screw x 3x5mm 3x5mm Cap Screw x VZ09 3D 3D Weight 98 x 3 00 VZ09 3D 3D Clutch Bell 05 x 00 VZ093 3D 3D Spring Catch 06 x VZ09 3D 3D Flywheel Nut 07 x 500 VZ095 3D 3D Clutch Disk 08 x 600 VZ096 3D 3D Flywheel 09 x 00 VZW0 SP 0 SP Front Belt (0) 77 x 800 VZW0 SP9 SP Rear Belt (9) 79 x 900 VZW06 SP375 SP Middle Belt (375)RR 78 x 950 BS07 Bevel Shaft 50 x 550 FD0 Engine Mount 08 x 350 FM3 Small Parts Set 88 89 90 x 9 76 x 00 FM37 Servo Savor () Optional parts mm Pitch 500 FM37B Servo Savor (0) Optional parts 0mm Pitch 500 FM37C 9 x set 93 9 95 x 96 x 500 FM38 - x 500 FM38 - FM33-9 Servo Saver (9) 3x8xmm Collar 3xmm Washer Brake Lever FM35 Clutch Shoe FM35 Clutch Spring FM353 Spring Nut FM356 6T -6L st Gear (6T) 3 x 5 8 x 7 x 8 x 9 x x 600 00 00 50 700

No. Part Names FM356 7T -7L st Gear (7T) FM356 8T -8L st Gear (8T) FM357 0T -0H nd Gear (0T) FM357 T -H nd Gear (T) FM357 T -H nd Gear (T) FM358-7L FM36-8L FM36-9L FM363 -H FM363-5H FM37 FM37 st Spur Gear (7T) 8T st Spur Gear (8T) 9T st Spur Gear (9T) T nd Spur Gear (T) 5T nd Spur Gear (5T) Linkage Set Tensionner Set No. Quantity Optional Parts x 700 00 x 700 Optional Parts 3 x Bell Guide Washer FM359 st Housing 3x6mm x 3x6mm Flat Head Screw x3 FM360 nd Shoe Set 8 9 0 x.6xmm.6xmm Cap Screw x FM36 nd Shoe Holder 5 x xmm xmm x FM36 7T x Optional Parts 6 x x Optional Parts 7 x Optional Parts x 5 x 06 07 x 6 x 57 x E E E-ring (E) x 3x3mm 3x3mm x FZ7 9mm 9mm Pillow Ball 99 x 3 FZ75 9mm 9mm Pillow Ball Nut 00 x 3 UM.8mm.8mm Ball End 98 x 6 UM8 UM9.8mm L.8mm Ball Stud (L) 0 x.8mm S.8mm Ball Stud (S) 78 x UM3 Tapered Collet 09 0 x W06 3mm 3mm Flat Head Washer 03 x 0 W05 6.8 3mm 6.8mm Flange H.Ball (3mm H) 0 x 0 W058 5.8 M3 5.8mm Flange H.Ball (3mm T) 0 x W505 Shock End 3 x SPARE PARTS () Optional Parts x Optional Parts x 5 x 0 x x 700 700 700 50 800 500 00 00 00 650 650 500 50 00 00 50 500 700 00 00 FOR JAPANESE MARKET ONLY. No. No. Part Names Quantity W507 Shock Diaphragm 36 x 0 00 00 W508 O-ring Set 5 x 350 W505 BL Shock Cap Set (Blue) 0 x 700 W506 Shock Plastic Parts 30A 30B x 50 W507 O O-ring Set 38 39 x 37 x 50 95 5.8mm 5.8mm Ball End 73 x 8 00 700 KP S Fluorescent Nylon Strap Pink (S) 6 x 8 80 700 KY S Fluorescent Nylon Strap Yellow (S) 6 x 8 80 70 KP M Fluorescent Nylon Strap Pink (M) 63 x 8 50 70 KY M Fluorescent Nylon Strap Yellow (M) 63 x 8 50 708 Color Antenna (Black Cap) 7 73 x 500 790 Color Silicone Tube 53 x 00 808 Rod Stopper 9 x 5 50 879 Hoby Grease pcs. 50 3983 V-One RR V-One RR Lola x 9050 75cc Fuel Tank (75cc Plate) 56 x set 9050 5CS 8mm -0 Fuel Tank Sponge Packing 5 pcs. CS-ring (8mm) x 5 905 xmm xmm Pin 5 x 0 905 O P5 O-ring (P5) 9 x 0 9053 5.8mm.8mm 5.8mm Hard Ball Joint (w/.8mm hole) 7 x 9638 Snap Pin 65 x 0 9696 Disk Brake Pad 5 x 9985 Hard Brake Lining x 967 6xxmm 6xxmm Ball Bearing 55 x 9659 x8xmm x8xmm Ball Bearing 56 x 966 3x5mm 3x5mm Shim Set x 0 9663 5x7mm 5x7mm Shim Set x 0 9699 0x5xmm 0x5xmm Ball Bearing 5 x 96995 5x0xmm 5x0xmm Thrust Bearing 6 x set 96996 5x0mm 5x0mm Ball Bearing 58 x Some of the parts included are not available as spare parts. Purchase optional parts instead. 000 500 00 600 00 00 000 800 50 50 00 800 000 OPTIONAL PARTS () No. No. Part Names Quantity 0 VZ069 Drive Belt 0 Hard Type (High durability.) 700 00 9 VZ07 Drive Belt 9 Hard Type (High durability.) 700 VZW00 SP7075 V-One RNC Special Main Chassis 7075 (for V-One R) Hard Main Chassis 7000 VZW008 V-One Rigid Axle (for V-One) For High Traction Course 000 VZW009 TCDV-One TCD Gear Set (for V-One) 7500 VZW00 Drive Washer Set Aluminum (Hard Type) No. Part Names VZW05 SP Brake Disk FOR JAPANESE MARKET ONLY. No. Quantity 700 00 96986 Soft Brake Lining Use Together with. 00 VZW07 Body Mount Shaft E-Clips Type (Hard Type) pcs 700 TSW TSW TSW5 7075 7075 Hard Main Chassis High Traction Type. V-One Aluminum Brake Disk Holder (V-One) Aluminum (Hard Type) Clutch Spring Adjust Tool Scale (0.05mm) 7500 500 9

No. Part Names No. Quantity TSW6 Aluminum Ride Height Gauge Large Type. 500 FM337 9mm 9mm Ball Screw High Intensity & Quality. 900 SPW5 Adjust Rod Set(L=5,0) pcs. 650 FMW FMW6 FMW.mm Body Stiffener (.mm) Required Processing. Clutch Shoe(Red) Mild for shifting. Rear Spoiler Required Processing. 900 000 700 FMW6 Clutch Spring(H) Hard Type 776 / 0x0x330mm Pit Box Size / 0x0x330mm 6800 89 Hobby Shears & Sander Making short work of cutting bodys. 000 98 659 3905 3905 39053 3905 39055 39056 Air Cleaner Oil Tuned Silencer Set (Side) Muffler Manifold (Side) Tuned Silencer Set (Back) Manifold (Back) Manifold Spring pcs. 5 Muffler Gasket 5pcs. (Side) 000 00 6800 800 500 7000 0 50 39058 SC Tuned Silencer Set (Back) Spring Connect Type. 8500 39059 SC Tuned Silencer (Back) 5800 39060 SC Manifold (Back) 0 3906 SC Muffler Joint & Ring Each One. 800 3968 560 5739 57507 57507P 57507G 57507Y Special Engine Mount Precision Camber Gauge Dust Creaner Team Team Silicone Fuel Tube (Clear) Team Team Silicone Fuel Tube (Pink) Team Team Silicone Fuel Tube (Green) Team Team Silicone Fuel Tube (Yellow) 500 00 000 00 00 00 00 Team 5803R Team Multi Box (Red) 9800 5803B Team Team Multi Box (Black) 9800 76 6v X-FORCE 600 6v X-FORCE 600 Ni-Cd Battery 3800 803 Taper Reamer Tool for making holes on Bodies. 800 80 5mm Ball-Point Hex Wrench 5mm 850 8765 Maintenance Stand Aluminum Stand for Maintenance. 800 OPTIONAL PARTS () 00 No. 90 9060 95 9605 Part Names Multi Ride Height Gauge Muffler Joint Pipe(-5) 6mm Titanium Adjust Rod 6mm FOR JAPANESE MARKET ONLY. No. Quantity 970 SC Spring 6pcs. 90 Loctite (medium strength) Screw Cement. 9606 6x8mm 6x8mm Shim Set Power Cleaner 9698 60700 6070 6 6 63 6 65 66 67 63 63 633 63 635 636 637 69505 69505-69505- 69506 69506-69506- 695030 69503 800 00 900 700 900 50 800 96 One-touch Plug Heat Set AC 800 9665 SP SP Bearing Liquid 000 Molybdenum Coat 600 96 500cc Quick Fuel Pump 500cc 00 SP Tornade Fuel.5L 3600 Tornade After Run Oil 600 GRP /0 F30 GRP /0 Touring Sponge Tire F30 (Wheel) GRP /0 F3 GRP /0 Touring Sponge Tire F3 (Wheel) GRP /0 F35 GRP /0 Touring Sponge Tire F35 (Wheel) GRP /0 F37 GRP /0 Touring Sponge Tire F37 (Wheel) GRP /0 F0 GRP /0 Touring Sponge Tire F0 (Wheel) GRP /0 F GRP /0 Touring Sponge Tire F (Wheel) GRP /0 F5 GRP /0 Touring Sponge Tire F5 (Wheel) GRP /0 WR30 GRP /0 Touring W Sponge Tire R30 (Wheel) GRP /0 WR3 GRP /0 Touring W Sponge Tire R3 (Wheel) GRP /0 WR35 GRP /0 Touring W Sponge Tire R35 (Wheel) GRP /0 WR37 GRP /0 Touring W Sponge Tire R37 (Wheel) GRP /0 WR0 GRP /0 Touring W Sponge Tire R0 (Wheel) GRP /0 WR GRP /0 Touring W Sponge Tire R (Wheel) GRP /0 WR5 GRP /0 Touring W Sponge Tire R5 (Wheel) V-One Power Universal Shaft (V-One) For Front. Swing Shaft For Front. Wheel Shaft For Front. Power Universal (Wide Tire) Swing Shaft Wheel Shaft 8T V-One Aluminum Drive Pulley 8T (V-One) 9T V-One Aluminum Drive Pulley 9T (V-One) High Heat Resistant Type., Titanium. pcs. 6 For Rear. For Rear. For Rear. 500 800 900 950 800 900 000 00 00 30

OPTIONAL PARTS (3) FOR JAPANESE MARKET ONLY. No. Part Names Qty. No. Part Names Qty. No. Part Names Qty. 9660 00 500 00 Silicone Oil (00) 96608 9666 Silicone Oil (500) Silicone Oil (00) for shocks. 50 550 5000 9660 Silicone Oil (50) 966 96755 Silicone Oil (550) Silicone Oil (5000) 00 600 6000 96603 Silicone Oil (00) 96609 96756 Silicone Oil (600) Silicone Oil (6000) 50 700 7000 9660 Silicone Oil (50) 9663 96757 Silicone Oil (700) Silicone Oil (7000) 600 00 for shocks. 600 00 600 800 for shocks. 00 0000 96605 Silicone Oil () 9660 Silicone Oil (800) 9696 Silicone Oil (0000) for diffs. 350 900 00 96606 Silicone Oil (350) 966 9696 Silicone Oil (900) Silicone Oil (00) 00 000 50000 96607 Silicone Oil (00) 9653 96963 Silicone Oil (000) Silicone Oil (50000) 50 00 00000 966 Silicone Oil (50) 9665 9696 Silicone Oil (00) Silicone Oil (00000) No. 0 0 03 0 05 06 0 3 5 8 9 0 3 68 x 5 6 7 8 9 30 3 x6 x8 x0 x5.6x8.6x0.6x.6x 3 33 x x6 x8 x0.6x6.6x8.6x0.6x 7 7 mm.6mm 3mm mm 0 each 0 each 3x 3x6 3x8 3x0 3 x 3 3x6 3x8 3x0 3x 3x 3x 3x6 3x8 3x0 35 3x5 3x6 3x8 3x0 Flanged Nut 00 x6 x8 x0 x 3x 3x 3x6 3x8 36 37 3x5 3x30 3x35.6x.6x5.6x6.6x8 7 75 3mm mm 0 pcs 0 pcs.6x.6x6.6x8.6x 3x 3x6 3x8 3x0 3x 3x 3x6 3x8 3x0 x6 x8 x0 x 3x 3x5 3x8 3x30 x5 x8 x0 x.6x8.6x0.6x.6x 3x6 3x8 3x0 3x 3x 3x6 3x8 3x0 x8 x0 x5 x0 3x 3x 3x6 3x8 3x30 3x3 3x3 3x35 x8 x0 x x.6x8.6x0.6x.6x 3x8 3x0 3x 3x 3x5 3x6 3x8 3x0 3x5 3x30 3x35 3x0 x0 x5 x0 x5 x8 x30 x35 x0 x5 96.6x8 mm Size (mm) Round Head Screw Bind Screw Flat Head Screw Cap Screw QUANTITY 00 00 00 0 each 00 each each each each each each each each each SCREW NUT etc. No. 0 3 7 8 9 50 53 5 57 60 6 6 63 6 Round Head Self-Tapping Screw.6x6.6x8.6x0.6x 3x6 3x8 3x0 3x 3x 3x5 3x6 3x8 3x0 x5 x0 x5 3x6 3x8 3x0 x8 x0 x x8 x0 Bind Self-Tapping Screw.6x6.6x8.6x0.6x 3x6 3x8 3x0 3x 3x 3x5 3x6 3x8 3x0 x0 x5 x8 5 x8 x mm Size (mm) Flat Head Self-Tapping Screw Flanged Cap Screw 00 Oval Head Screw 3x6 3x 3x 3x6 3x3 3x 3x5 3x0 x x5 x8 x 5x 5x5 5x6 5x30 5x0 QUANTITY 00 00 Nylon Nut 00 77 78 79.6mm 3mm mm 5 pcs 5 pcs 5 pcs 8 5mm pcs 83 3mm 5 pcs 00 each each 00 0 each 00 3 each 3 each 3 each 3 each 3 each 65 3x0 3x5 3 each 66 x8 0 each No. 80 85 86 380 38 38 383 38 385 386 387 390 FOR JAPANESE MARKET ONLY. QUANTITY mm E.5 E.0 E.5 E3.0 E.0 E5.0 E6.0 E7.0 E0.0 Ø Nut Flanged Nylon Nut 00 Washer mm.6mm 3mm mm 5mm E E-Clips 00 5 pcs 00 0 each 0 each 50 0 pcs 0 pcs 0 pcs 0 pcs 0 pcs 0 pcs 0 pcs 6 pcs 6 pcs 3

() 00 0 0 0 7 7 6 8 0 (3) (),00 00 80,680 () () 0 0 0 7 7 6 8 0 ()

30 V-One RR

R THE FINEST RADIO CONTROL MODELS 3 3-003 53 06-9-5 () 0 00 8 00 60950- PRINTED IN JAPAN