p01.pdf

Before commencing assembly, please read these instructions thoroughly. R THE FINEST RADIO CONTROL MODELS INSTRUCTION MANUAL INFERNO MP-7. INDEX REQUIRED FOR OPERATION RADIO PREPARATION BEFORE YOU BEGIN ARRANGEMENT OF PLASTIC PARTS ON RUNNERS ASSEMBLY ADJUSTMENT OPERATING YOUR MODEL SAFELY EXPLODED VIEW SPARE PARTS & OPTIONAL PARTS 6 7 8 6 7 8 0 SAFETY PRECAUTIONS This radio control model is not a toy! First-time builders should seek the advice of experienced modellers before commencing assembly and if they do not fully understand any part of the construction. Assemble this kit only in places out of children's reach! Take enough safety precautions prior to operating this model. You are responsible for this model's assembly and safe operation! Always keep this instruction manual ready at hand for quick reference, even after completing the assembly. *SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE. 000 KYOSHO No. 08

R R REQUIRED FOR OPERATION () ch radio control set with servos. This kit requires a channel radio control set with servos. Because there are stick-type and wheeltype transmitters, use which ever fits your convenience best. Switch the reverse (transmitter) for the throttle control. For more information on the radio con-trol set, refer to its instruction manual. Stick-type ch radio set. Wheel-type ch radio set. AA-size Batteries (For Transmitter) AA AA Battery for Receiver No.7 No.76 6V-600mAh 6V-000mAh RX RX Ni-Cd Battery Ni-Cd Battery Suitable servos & receiver Servo Receiver Engine & Muffler Plug Joining Pipe Manifold This kit requires a. class engine. Engine for.-class cars Only using a type of. class engine, which is made crank shaft and pilot shaft as one part (SG shaft only). Muffler No.IFW-7 SP (FEMCA) SP Silencer (FEMCA) No.9 Muffler Joining Pipe No.9 Manifold (O.S.RZ, Picco, Nova Rossi) No.96 Manifold (O.S.RG) Required for engine starting: Glow Fuel Fuel Pump Plug Heater Paint For painting the body, use Kyosho paints for models! No.780 RC No.96 Quick Fill Fuel Bottle RC Model Fuel PRO Spec Fuel (Buggy) Plug Wrench Starter No.96 One-touch Plug Heater Set Battery No.0 POLYCA COLOR No.760 767 KYOSHO SPRAY COLOR No.80 Locking Jig & Wrench No.79 Starter Box KY OSH O S PR AY CO LO R KY OSH O S PR AY CO LO R Other equipment required. Shock Oil Gear Differential oil or Gear Differential Grease M Strap (M) SIL I OCONE IL SIL I OCONE IL No.70KP / KY Fluorescent Strap

REQUIRED FOR OPERATION () 6 Tools required Phillips Screwdriver (L.M.S) Needle Nose Pliers Instant Glue Sharp Hobby Knife Wire Cutters Screw Cement TOOLS INCLUDED Hex Wrench (.mm, mm,.mm, mm) Awl Box Wrench Rubber Cement Grease Cross Wrench Grease No.80 SPECIAL TAPER REAMER No.89 ROUND CUTTER & SANDER No need to pre-drill! Drills neat mm to mm holes directly! For trimming bodies! Cutting along curved lines never was so easy! Set up the radio control system as indicated below. RADIO PREPARATION 6 7 8 9 0 START FINISH 8 6 7 8 9 0 Install batteries. (Transmitter) Extend the antenna. (Transmitter) Connect the charged Ni-Cd battery to the receiver. Extend the antenna. (Receiver) Center the trims. Switch on. (Transmitter) Switch on. (Receiver) Make sure the servos are in command. Switch off. (Receiver) Switch off. (Transmitter) Retract the antenna. (Transmitter) 6 7

BEFORE YOU BEGIN () Read through the manual before you begin, so you will have an overall idea of what to do. Check all parts. If you find any defective or missing parts, contact your local dealer or our Kyosho Distributor. How to read the instruction manual: Front Suspension x 0mm Metal Bushing No., No., No.6 This instruction manual uses several symbols. Please note them during the entire assembly. King Pin 6 6.8mm Pillow Ball (Black) R 7 L 8 Key Number, Part Name, True-to-scale Diagram, Quantity Used All parts except screws are identified by key numbers. For purchasing spare parts, find the key no. of the part needed in the spare part list and refer to the left column to look up the corresponding order no. Symbols used throughout the instruction manual, comprise: Part bags used. mm Drill holes with the specified diameter (here: mm). Must be purchased separately! Apply epoxy glue. Cut off excess. Pay close attention here! Apply instant glue (CA glue, super glue). Cut off shaded portion. Apply rubber cement. Tentatively tighten. Apply grease. Ensure smooth non-binding movement while assembling. Apply threadlocker (screw cement). True-to-scale diagram. x Assemble as many times as specified (here: twice). Assemble in the specified order. Assemble left and right sides the same way. 90 No.90 Ball bearings are optional! (with optional part no.)

BEFORE YOU BEGIN () This kit contains screws and hardware in different metric sizes and shapes. Before using them, check the screws on the true-to-scale diagrams on the left side in each assembly step. Some screws are extras. SCREWS OTHER HARDWARE Screw Self-tapping (TP) Screw Screw Washer Nut E-ring mm mm mm Cap Screw TP F/H Screw mm Flat Head (F/H) Screw Set Screw F/H Screw mm Metal Bushing Bearing mm Pillow Ball mm 0mm 6.8mm 6 Self-tapping (TP) screws cut threads into the parts when being tightened. Excessive force may permanently damage parts when tightening TP screws. It is recommended to stop tightening when the part is attached or when some resistance is felt after the threaded portion enters the plastic. Correct Wrong Overtightened. The threads are stripped. MEMO

ARRANGEMENT OF PLASTIC PARTS ON RUNNERS () No. Shaded parts are not used. 8 8 66 66 66 6 6 6 66 66 66 No. Use the parts within the dotted lines as tunning options. 9 Shaded parts are not used. 7 9 6 6 6 No. 7 70 7 7 9 9 8 9 0 9 89 6 90 6 6

ARRANGEMENT OF PLASTIC PARTS ON RUNNERS () No.6 9 9 reguired, when using a stabilizer for front. 9 6 6 7 9 6 No.9 6 7 Shaded parts are not used. 9 9 8 8 8 0 6 7 9 9 9 7

Gear Differential x mm Set Screw No. 8 x 6mm Ball Bearing 8 ( ) (For front and rear) xmm 9 0 x 0mm Shim 0 6 6mm O O-ring.6 x mm Shaft (Black) Flat surface 7 ( ) (For center) 6 x x For front and rear For center Gear Differential x 0mm TP TP F/H Screw 8 x mm TP TP F/H Screw No. 6 Diff. Oil x0mm.6 x mm Shaft (Black) 8 x 6mm Ball Bearing 6 6mm O O-ring 7 8 ( ) (For front and rear) ( ) (For center) ( ) (For front and rear) ( ) xmm (For center) x x For front and rear For center Rear Gearbox No., No., No., No.0 x 0mm TP TP Screw x0mm x mm 9 x 6mm 0 TP TP F/H Screw Thick Thin Shim 6 8 8 x 6mm Ball Bearing Adjust the backlash with the shims. 9, 0 9, 0 7 xmm 8 Part bags used. x Assemble in the specified order. Apply grease. Assemble as many times Must be purchased as specified. separately!

Rear Gearbox x mm Set Screw No., No., No.0 Tighten the set screw to the flat spot. xmm x0mm x 0mm Screw L Joint Cup (L) x mm TP TP Screw xmm Rear Shock Stay No., No., No.0 x 0mm Cap Screw x 0mm TP TP Screw x0mm x mm x 0mm TP TP Screw Screw Holes for mounting. 7 6 x0mm x0mm xmm 6 Wing Stay No., No.0 9 xmm 9 8 0 xmm x mm TP TP Screw xmm x mm TP TP Screw x 0mm Screw Note the types of screws! xmm x0mm Part bags used. Apply threadlocker (screw cement). Pay close attention here! Assemble left and right sides the same way. 9

7 Rear Suspension x mm Set Screw 9 EE-ring (Silver) 8 x 8mm Shaft (Black) No., No. L For left side. L maked. 6 0 For right side. R R maked. 8 x 6mm Ball Bearing 8 xmm Top 6 x 8 x mm Plastic Collar xmm 9 7 Bottom mm For adjusting the ground clearance..6 x 7mm Shaft x mm Set Screw 9 6 Adjust the wheel base by using the other spacer instead of 6. 8 Rear Suspension No., No.0 x mm Set Screw 7.8mm Ball End x.mm approx..mm 9 Rear Suspension x 7mm Shaft No., No.0 Holes for mounting. For right side. x 0mm E Cap Screw E-ring (Black) 7.8mm Flange Ball (Black) For left side. x0mm Part bags used. Assemble left and right sides the same way. x Assemble in the Assemble as many times specified order. as specified. Pay close attention here! True-to-scale diagram. 0

0 Rear Suspension mm Nylon Nut No., No.0 8 6 6 6mm Suspension Bolt 8 7.8mm Ball mm Holes for mounting. 7 Rear Suspension No., No.0 x0mm xmm xmm xmm x mm Set Screw x mm.8mm Set Screw Ball x 0mm Set Screw.8mm S Ball End (S) x mm Screw.6 x mm Stabilizer Ball F/H Screw 9 xmm.6xmm 0 9 xmm.6xmm Chassis No.9, No.0 x 0mm TP TP F/H Screw x0mm x0mm Part bags used. Pay close attention here! Assemble in the specified order. Assemble left and right sides the same way. Ensure smooth non-binding movement while assembling.

Chassis x 0mm F/H Screw x 8mm Cap Screw No., No.9, No.0 8 76 7 x8mm 6 6 Torque Rod Ball 8 6.8mm L Ball End (L) 76 6.8mm Ball x0mm Front Gearbox No.6, No.0 x 0mm TP TP Screw 8 x 6mm Ball Bearing 6 8 x0mm 60 9 x 6mm 0 Thick Thin Shim Adjust the backlash with the shims. 9, 0 9, 0 7 x0mm Front Gearbox x mm Set Screw x mm TP TP F/H Screw No., No.6, No.0 Tighten the set screw to the flat spot. xmm 6 x 0mm TP TP F/H Screw 8 S Joint Cup (S) 6 8 xmm x0mm Part bags used. Assemble in the specified order. Apply grease. Apply threadlocker (screw cement).

6 Front Shock Stay No.6, No.0 x 0mm Cap Screw x 0mm Screw x0mm x mm TP TP Screw 6 Holes for mounting. 7 x0mm xmm x0mm xmm 7 Front Suspension No.6, No.0 x 0mm x mm For right side. Cap Screw Set Screw ÒRÓ ÒRÓ maked. 69 8 x 6mm Knuckle Collar Ball Bearing 66.6 x 7mm xmm Shaft 69 69 x0mm 6 68 x0mm For left side. ÒLÓ ÒLÓ maked. 6 67 8 Front Suspension For right side. x mm Set Screw 9 9 E E-ring (Silver) E E-ring (Black) 7 7 x 8mm Shaft x 7mm Shaft No., No.6, No.0 xmm 9 70 Top Bottom mm For adjusting the ground clearance. For left side. Part bags used. Assemble in the specified order. Assemble left and right sides the same way. Apply threadlocker (screw cement). Pay close attention here!

9 Front Suspension No., No.6, No.0 7 x 0mm Set Screw 76 6.8mm Ball 7 9 EE-ring (Silver) 7 x 0mm Shaft (Black) 7 9 6 6mm Suspension Bolt mm Nylon Nut 7 6.8mm Ball End 7 6mm approx. 6mm 76 mm mm 7 9 6 0 Chassis No.6, No.0 x 0mm TP TP Screw x 0mm TP TP F/H Screw 77 x0mm x0mm x0mm Center Gearbox 8 mm Disk Plate Bolt 78 Brake Caliper 8 No.8 80 79 78 7mm approx. 7mm 8 79 Brake Pad (Black) Center Differential 8 79 78 80 8 Part bags used. Assemble left and right sides the same way. Assemble in the specified order. Apply rubber type glue. Pay close attention here!

Center Gearbox No.8, No.9, No.0 8 7 () (Short) () 86 (Long) 9 9 x mm TP TP F/H Screw 8 mm O O-ring x 6mm F/H Screw x6mm xmm xmm x6mm Center Gearbox x0mm No.8, No.9, No.0 9 88 89 90 xmm x0mm mm 7mm Bend the rods if they contact the plate. xmm 9 87 9 Use thick one. x mm Set Screw 88 89 87 x 0mm TP TP Screw Steering No.7, No.0 Short Long 99 99 98 x0mm x 0mm Screw mm Flanged Nut 96 6 x 0mm 98 Steering Collar Metal Bushing Note the direction. x0mm 98 97 96 9 x0mm 99 Steering Pin x 0mm Washer 9 x0mm mm 96 mm 9 Part bags used. Pay close attention here! Apply grease. Tentatively tighten.

Steering No.7, No.9, No.0 x0mm 0 Long Short Remove these screws and retighten after installing 00..mm approx..mm x0mm 00 Note the direction. 9 0 x 0mm Screw 8 x 0mm x mm F/H Screw F/H Screw x0mm x0mm mm ( ) (Flanged) mm mm Flanged Nut Nut 8 6.8mm L 0 Ball End (L) Tapered Collar 0 xmm 0 x 0mm 9 6.8mm Adjustable Rod Ball (silver) Note the types of screws! mm xmm 6 Engine x 6mm Cap Screw x 0mm Cap Screw 0 x 0mm Shim No., No.0 x 0mm Washer 07 Pilot Nut Assemble the following parts with pulling the crankshaft. 0 Use 0 taper collet for assembling with com with kit. x0mm Engine x 0mm Ball Bearing 06 0 Tapered Coret x 8 x 0.mm Shim mm Washer x0mm 0 08 07 09 x8x0.mm 0 0 x6mm x8x0.mm mm A number and / or type of shim need to be adjusted depending on the type of engine. 6 Part bags used. Assemble left and right Apply threadlocker True-to-scale Pay close attention Ensure smooth non-binding Must be purchased sides the same way. (screw cement). diagram. here! movement while assembling. separately!

No., No.0 7 Engine Insert a sheet of paper before installing. Front 80 80 x 6mm F/H Screw x0mm x 0mm Flanged Cap Screw x0mm x6mm x6mm 8 Muffler No.9, No.0 x mm Set Screw x 6mm F/H Screw xmm Manifold 8 8 Muffler Muffler Joining Pipe Nylon Strap x6mm Bend so it fits into the muffler. Part bags used. Must be purchased separately! 7

9 Fuel Tank x mm TP TP Screw No.9, No.0 xmm xmm No.876 To protect the engine from dirt infiltration, purchase Kyosho's No.876 Fuel Filter. x 0mm TP TP F/H Screw 8 8 Note the types of screws! x0mm x0mm 7mm Cut the Silicone Tube to 7mm Length. 0 Radio x 8mm Screw x 0mm Screw x 0mm Screw x 8mm TP TP Screw 7 No.9, No.0 7 8 x0mm 6 x0mm Switch x8mm x8mm x8mm x8mm Switch 9 mm 9 Radio Antenna Receiver 0 No.0 0 Hook Pin Better to fill some sponge between radio box and receiver as well as battery. Battery 0 Part bags used. Pay close attention here! Must be purchased separately! mm mm Drill holes with the specified diameter. 8

Radio No.0 x 0mm TP TP F/H Screw x0mm x0mm Radio xmm Steering Servo xmm x0mm No.9, No.0 Throttle Servo x mm TP TP Screw xmm 8 x 0mm TP TP Screw 6 x0mm x 0mm TP TP F/H Screw x mm Screw 8 Note the types of screws! ( ) (For transponder.) Cords Connect as per radio. 8 x0mm 8 Radio 6 mm No.7, No.9, No.0 x mm F/H Screw Parallel xmm 0 0mm mm Flanged Nut 0 Tapered Collar.8mm Ball.8mm L Ball End (L) 6 x 0mm Adjustable Rod 0 xmm mm Part bags used. Must be purchased separately! Pay close attention here! Cut off shaded portion. 9

Radio Servo Horn No.7, No.9, No.0 x6mm.6mm 7 7 Note the directions of and 7. 7 9mm approx. 9mm x6mm x mm Set Screw 6 x 6mm Cap Screw.6x6mm 7mm approx. 7mm Throttle Rod 98mm xmm 7 xmm 7 8 9 OS. With O.S. and NOVA Rossi engines : With Picco engines :.6 x 6mm Cap Screw.6mm Nylon Nut 8 Linkage Spring 8 Spring 9 mm Stopper Brake Rod x 0mm Throttle Rod xmm 0 87mm Parallel 6 8 xmm 0 Adjuster Nob 9 Brake Rod 7 xmm Adjuster Rod 6 8 9 xmm 6 Throttle Linkage Adjustment < > < > < > < Neutral > < High Throttle > < Brake > mm 6 mm 6 6 Brake Adjusting Knobs Upper linkage Ð rear brak Lower linkage Ð front brake mm Adjust with this screw the carburetor so it cannot close more than mm. 0 Part bags used. x Ensure smooth non-binding Cut off shaded portion. Assemble as many Tentatively tighten. Must be purchased movement while assembling. times as specified. separately!

T H E 7 Engine No., No.0 x 0mm TP TP F/H Screw Rainy Weather 8 9 After putting the cover on, loosen the screw, fit in the plastic washer and screw in the screw again. 0 Soak inner sponge with oil. 8 9 No.98 Air Cleaner Oil x0mm 7 F I N E S T R A D I O C O N T R O L M O D E L S 6 No. 8 Shock.6mm Nylon Nut Collar (White).6mm Washer 6 Collar (Black) mm O O-ring 8 9 Piston (Black) 7 C C-ring 8 6.6mm.6mm 9 0 6 0 ( ) (Short) For Front ( ) (Long) For Rear ( ) (Short) For Front ( ) (Long) For Rear 8 6.8mm S Ball End (S) 7 7 Fit into groove. x x For Front For Rear 9 Shock No. Fill in until shock oil nearly overflows. Shock Oil 60 6 Pull down the piston. Then, gently move the piston up and down to get rid of air bubbles. Insert deeply. Check if piston moves smoothly. x x Part bags used. Assemble as many times as specified. Must be purchased separately!

0 Shock 6 6.8mm Ball (Black) No. 6 86 ( ) Ð (Short) Ð For Front 87 ( ) Ð (Long) Ð For Rear 66 For Spring adjustment. Onry on front! 7mm 6 6 6 x x For Front For Rear Shock No., No.0 68 mm < > < Front > xmm 68 Front Shocks Rear Shocks mm < > < Rear > mm 69 Nylon Nut xmm x mm Set Screw (Silver) 68 mm 69 x 7mm Shock Bushing Shaft 69 Wheels Slide the tires into these slots in the wheels. Clean the tire rims with thinner beforehand. 7 Apply instant glue little by little in the order. 8 7 70 8 6 x Part bags used. Cut off shaded portion. x Assemble as many Assemble left and right Apply instant glue times as specified. sides the same way. (CA glue, super glue). Ensure smooth non-binding movement while assembling.

Wheels No., No.6, No.0 < > < Front > 7 88 8 x x 0.mm Shim 7 Wheel Stopper Nut < > < Rear > 88 8xmm In case of vibrations, insert a 88 8xmm shim. 88 7 Side Guard No.0 x0mm 7 7 (L) (R) x 0mm TP TP Screw 6 x0mm x0mm Trim the shaded portion away so the exhaust pipe can exit. Body Shell 8mm 76 77 Fit to the engine when cutting out. 8mm 7mm Fit to the muffler when cutting out. Hole for antenna pipe. Part bags used. Assemble left and right sides the same way. Cut off shaded portion. 7mm 7mm Drill holes with the specified diameter.

6 Painting Before painting, use a neutral detergent to remove any oil residues and dirt. Mask the windows from the inside. Refer to the pictures on the box for the color scheme. Paint the body shell from the inside using KyoshoÕs spray colors. After painting, remove the protective film from the body shell. 7 Decals Apply decals to any spots you like.

8 Body Shell No.0 79 79 78 79 79 78 78 Wing Plastic Washer Slightly bend the body pins as shown in the diagram for easier removal. 79 Body Pin 6 ADJUSTMENT Part bags used.

Toe Adjustment (Front) Toe - in Tie Rod L Toe - out Adjust the front toe either by making the tie rods longer or by making them shorter. L Length (L) Toe - in Shortening. Steering Characteristics Straightline stability becomes better. Steering becomes milder. Straightline stability becomes worse. Toe - out Steering response becomes quicker. Ensure that the length of both the left and right tie rods is the same. Caster Angle (Front) Making longer. Camber Adjustment L Length (L) Making longer. Upper Rod 6 6 Positive Camber Caster Angle can be changed, with a set Shortening of 89 and 90, instead of 6 and 6. Negative Camber 6 L Front / Rear Front Rear Front Rear Adjust the front / rear camber either by making the upper rods longer or by making them shorter. Negative Camber Steering Characteristics Positive Camber Steering becomes milder. Rear tire grip becomes worse when entering corners. Enters corners more aggressively. Gives rear tires more grip when entering corners. Ensure that the length of both the left and right upper rods is the same either by unscrewing or by tightening the set screw. 6 6 6 89 90 Front sus holder is made for set using. Must use together with 6 and 6 set or 89 and 90 set. 6 6 Steering Characteristics Steering becomes Caster (High) milder. 89 90 Steering response Caster (Low) becomes quicker. Toe Adjustment (Rear) Ride Height Adjust the front / rear ride height. mm Hex Wrench (mm) Set Screw Toe Adjustment (Rear) 6 Adjust the rear toe by replacing 6. Steering Characteristics 9 Rear tire slip becomes Toe - in more important. Neutral steering (Standard) Toe - in 9 Gives the rear tires more Toe - in grip when exiting corners. Place the chassis on a level surface and lift the front of the model. When setting down the model again, check if both front wheels touch down at the same time. IFW-6 Screwing in the set screw. Unscrewing the set screw. 6 Brake IFW-6 Ride height becomes lower. Ride height becomes higher. This is pictur for assembling double disk brake. Center Differential IF- 6 9 9 No. IF- 6 IFW-6

OPERATING YOUR MODEL SAFELY In order to avoid accidents and personal injury, be sure to observe the following: Since exhausts and fuel vapors are noxious to health, use fuel only outdoors! Keep hands and objects away from rotating engine parts to avoid personal injury. Because after running the engine, the engine and the muffler are extremely hot, beware of getting burned! For accident prevention, do not run your model under Only use glow fuel for radio control models! Never use the following circumstsnces: gasoline or kerosene which might cause accidents such as fires! In place where many people gather. Near residential districts, schools and hospitals. Because fuel is highly inflammable, never use fuel indoors, near any source of heat, open flames or even Near roads, railroads, air corridors and electric lines. sparks! Do not dispose of an empty fuel can into a fire. It might explode causing serious injury! Also make sure that nobody is using the same frequency as you do at the same time! Be particularly careful not to swallow fuel or to get fuel When the radio batteries are empty. into eyes! Nevertheless, should fuel be swallowed, immediately induce vomiting and call a physician. Should fuel get into eyes, thoroughly rinse the eyes and seek medical advice. Always store fuel in a safe place out of children's reach with the cap shut tight! The place for storage should be dark, cool and dry! When the model's control or running behavior is strange. 7

INFERNO MP-7. < > Parts indentified only by key numbers are not sold individually 8 9 B IF 6 IF6BL 6 IF 7 IF 68 IF IF BS6 9 7 IF9W 7 8 9 IF8 IF8 96 IF8 9 IF8 9 IF 76 IF08 0 IF08 0 8 9 BS6 BS6 IF7 69 IF7 69 IFW0-68 IF 6 IF 7 IF 7 IF 69 IF 70 IF 60 IF7 77 IF6 66 IF 69 BSW- 7 IFW0-68 BS 7 IF6 67 IF 7 IF 7 IF 8 IF IF 8 IF 8 IF BS B 96 8 96 8 98 0 W0 0 IF0BL 97 W0 0 LA IF BS6 9 98 99 98 99 W0 0 FM9 79 IF 0 IF 6 IF 76 8 E A I J IF8 6 90 KC OT OT W0 0 90 6 LA 0 9 IF- 6 BS6 BS6 C D C IF6BL IF7 IF7 IF7 IF7 IF 7 IF FM8 8 IF9BL 00 IF 6 F G 7 9 7 8 9 G F IF7 IF 90 90 IF7 IF 89 IF 89 IF 7 IF 6 IF 7 9 9 8 8 6 6 0 6 7 0 0 7 7 8 9 IF 88 IF 87 IF7 9 968 0 IF 6 IF IF 9 707 78 79 80 79 78 8 IF IF8 IF 8 8 8 IF IF 8 IF7 9 IF IF7 9 IF9BL 90 78 78 79 79 80 8 K L N N IF 86 IF IF 9 IF 9 IF7 IF IF IF IF 8 BS-6 BS6 IF7 0 IF 7 IF0BL 6 BS79 9 BSW 7 IFW0-68 BSW7W 77 968 0 IF 8 FM9 79 FM9 79 FM9 79 BSW7W 78 BSW7W 78 IF7 IF7 BS IF IF 0 8 0 9 IF6 IF IF 6 IF 7 IF9W 7 IF6 7 IF 8 IF IF IF 7 IF9 0 IF IF BS 7 IF 6 BS6 BS6 IF 7 IF7 IF7 IF7 IF 69 IF7 8 IF IF IFW0-68 BSW 7 IF7 8 9 8 9 8 8 8 8 9 8 9 IF 8 9 8 IF09 8 7 8 IFW6 IFW 07 IF 7 IF 7 0 09 KC 08 06 0 IF 9 IF 9 IF07 80 IF07 80 IF0 H M L K J M I E H D A 8 9 96 9 IF 6 IF6 7 EXPLODED VIEW 000 KYOSHO / Front Shoch Front Diff Center Diff Rear Diff Rear Shoch Rear Shoch Front Shoch

0 Gear Differential < EXPLODED VIEW () > Shock Center Front / Rear BS6 IFW6 IFW IF06 Rear Front 8 BS6 6 0 BSW77 BSW77 BSW BSW77 BSW77 BSW6 BSW BSW IFW0- BSW78 BSW7 IFW9 BSW IFW0- IF0 BS6 IF0 IF9 BSW6 IF0 IF0 7 IF0 BS07 IF9 IF9 IF0 IF0 BSW6 6 BSW6 IF0 IF0 9 BS07 9 IF0 0 IF0 IF0 IF0 IF0 IF9 6 BSW6 6 BS6 8 IF0 7 6 7 BSW 6 7 66 66 66 66 6 8 BSW 6 8 86 BSW76 87 6 6 6 IFW0-6 60 BSW 60 0 BSW7 IFW- 6 BSW78 6 9 IFW9 9 6 BSW 6

No. Part Names No. Quantity BS6 8x6mm 8x6mm Ball Bearing x 60 BS6 6.8mm 6.8mm Ball 9 x 0 0 BS Shim Set 9 0 7 x 0 BS7 O P O-ring (P) 8 x 0 00 BS79 Switch Boots 9 x 80 BS07 Bevel Shaft 9 x 0 BSW Plastic Parts Set 8 6 x 000 BSW Shock Diaphragm 60 x 00 BSW O O-ring 6 6 x 7 x 800 BSW Steel Shock Bushing 7 x 800 BSW6 O P6 O-ring (P6) 6 x 0 00 BSW6 Front Soft Spring 86 x 600 BSW7W Color Nylon Wing (white) 77 x 78 x 000 BSW7 M Shock Shaft (M) 0 x 600 BSW7 L Shock Shaft (L) x 600 BSW76 Rear Soft Spring 87 x 600 BSW77 Adjust Collar 6 x 66 x 00 BSW78 Shock Boots 6 x 600 FM9 Body Pin 79 x 0 0 FM8 Joint 8 x 600 IF6 Knuckle Arm 66 67 x 800 IF7 Knuckle Arm Collar 69 x 800 IF Side Guard 7 7 x 800 IF T Drive Bevel Gear (T) 8 x 00 IF7 IF IF9 IF IF IF IF6 IF0 IF0 IF0 IF0 IF0 IF06 IF07 IF08 IF09 Linkage Set 8 7 x 9 0 6 8 x 7 x 9 x Steering Pin 98 99 x.6xmm.6xmm Shaft x Center Drive Joint x 6.8mm 6.8mm Ball 7.8mm 7.8mm Ball 7.8mm 7.8mm Flanged Ball 76 x 8 x x Differential Shaft Set 8 9 0 x Differential Bevel Set x 0 x Differential Case x Center Differential Shaft 6T Spur Gear (6T) 7 x x 8mmT 8mm Bevel Gear (T) x x0mm Engine Mount Spacer 80 x x0mm Flanged Cap Screw x Engine Mount 0 x mm P mm Flywheel Set (for P) 0 06 x SPARE PARTS 000 0 80 700 00 00 00 70 00 00 800 900 00 600 600 00 00 No. IF0 IF IF IF IF IF IF6 IF7 FOR JAPANESE MARKET ONLY. No. Quantity Part Names.6x7mm.6x7mm Pin x Suspension Shaft Set 8 7 7 x 6 69 x Bulkhead Set 6 7 x 9 x 600 Suspension Plate Set 60 x 0 Rear Hub Carrier x 6 x 0 Wheel Hub xmm x xmm Set Screw x 90 Wheel Nut 7 x 0 x x 0 x xmm, xmm Set Screw, xmm xmm Set Screw x0mm x Rear Stabilizer Set x0mm Set Screw 000 xmmx xmm Bind Screw.6xmm x.6xmm F/H Screw 6 7 x 8 x IF8 x8mm Rear Torque Rod Set x8mm Cap Screw x x0mm x0mm F/H Screw x 00 IF9 Rear Wheel Shaft 0 x 70 IF0BL Rear Shock Stay 6 x 70 IF IF 8 9 0 x Wing Stay x xmm Lower Suspension Arm 7 70 x xmm Set Screw x 00 90 IF Upper Arm Set 7 7 7 x x 700 IF Suspension Holder 6 6 89 90 9 9 x 0 IF IF6BL Universal Swingshaft 68 x Front Shock Stay 6 x 00 0 IF7 Bumper 77 x 00 IF8 Servo Saver Set 9 9 x set 9 96 x 00 IF9BL Plate Set 90 00 x 700 IF0BL Steering Plate 97 x 00 IF Center Differential Housing 8 8 x 00 IF Brake Cam Set 87 88 x 89 x 60 IF Brake Disk 80 x 0 IF Brake Disk Set 78 79 8 x 80 x 00 9 0 6 7 IF Receiver Box 9 x Screw Set 800 8 9 x 8 x IF6BL Radio Plate x 0 IF7 cc Fuel Tank (cc) x 8 x 800 IF7- Antiribration Rubber 8 x 00 IF8 IF9W MP-7. Body (MP-7.) 76 x Masking Seal x 0 Wheel Set (0 spoke-type, white) 70 x 000 800 IF0 IF Main Chassis MP-7. Decal Set (MP-7.) x MP-7. for MP-7. Decal x 000 00 IF 7mm 7mm Wheel Wrench (7mm) Wheel Wrench 7mm x 00 IF Front Hub Carrier 6 6 x 70 00 00 00

SPARE PARTS No. No. Part Names Quantity IF Center Shaft (Rear) 86 x 0 00 IF Swingshaft 7 x 60 IFW9.x Shock Piston.x Hole 9 x 0 IFW0- Shock End Cap 6 x 68 x 8 000 IFW0- Shock Bushing 68 x 8 00 IFW- L Shock Case (L) x 00 IFW6 SPT SP Clutch Bell (T) x 00 IFW PC PC Flywheel Nut 07 x 0 IFW6- ML Shock Case (ML) x 00 KC Special Clutch Shoe 08 x set 09 0 x 00 LA.8mm.8mm Ball End x 00 OT.8mm.8mm Ball x 0 0 W0 Tapered Washer 0 x 0 0 96 6.8mm 6.8mm Ball End 8 x 00 8 E.mm E-ring (.mm) 9 x 0 0 8 E mm E-ring (mm) x 0 0 707 Color Antenna x 6 00 90 x0mm x0mm Ball Bearing x 700 No. 90 90 90 9 968 98 Part Names x0mm x0mm Rod HD HD Air Cleaner Clutch Spring Muffler Stay Snap Pin x0mm x0mm Rod FOR JAPANESE MARKET ONLY. No. Quantity 6 x 6 7 8 9 0 x 09 x 8 8 x 0 x 0 0 x 0 00 800 00 600 00 00 Some of the parts included are not available as spare parts. Purchase optional parts instead.

No. Part Names No. Quantity BSW7BL Color Nylon Wing (Blue) 000 BSW7KG Color Nylon Wing (Fluorescent Green) 000 BSW7KO Color Nylon Wing (Fluorescent Orange) 000 BSW7KY Color Nylon Wing (Fluorescent Yellow) 000 BSW7G Color Nylon Wing (Gun Metallic) 000 BSW8.x 9 Shock Piston.x Hole instead of 9. 0 IF9BL 0 / Wheel (0-spoke / Blue) 800 IF9KG 0 / Wheel (0-spoke / Fluorescent Green) 800 IF9KO 0 / Wheel (0-spoke / Fluorescent Orange) 800 IF9KY 0 / Wheel (0-spoke / Fluorescent Yellow) 800 IF9G 0 / Wheel (0-spoke / Gun Metallic) 800 IFW7, Wing Stay Collar instead of. aluminum 900 IFW 7 8 Universal Center Shaft (Rear) 7 8 in one piece. 600 IFW8.6mmx 9 Shock Piston.6mmx Hole instead of 9. 0 IFWR S 86 Spring (S) Red Super Soft instead of 86. 900 IFWGR S 86 Spring (S) Green Soft instead of 86. 900 IFWBL S 86 Spring (S) Blue Medium instead of 86. 900 IFWW S 86 Spring (S) White Hard instead of 86. 900 IFWR L 87 Spring (L) Red Super Soft instead of 87. 900 IFWGR L 87 Spring (L) Green Soft instead of 87. 900 IFWBL L 87 Spring (L) Blue Medium instead of 87. 900 IFWW L 87 Spring (L) White Hard instead of 87. 900 IFW t=.0 80 Special Disk Plate (t=.0) instead of 80. 00 IFW6 8 Disk Plate Bolt (Long Double Disk) instead of 8. 00 IFW7 SPFEMCA SP Silencer (FEMCA) high-power muffler 6800 IFW R 86 Universal Center Shaft (R) 86 in one piece. 800 IFW7 IFW IFW SPT SP Clutch Bell (T) instead of. PC PC Clutch Spring for -piece clutch. PC PC Clutch Shoe for -piece clutch. 00 600 00 IFW0 IFW0 SP Special Main Chassis hard anodized 800 SP Special Engine Mount Duralumin 00 IFW0.mm Rear Stabilizer Bar (.mm) for Setting 0 IFW0 Front Stabilizer Set Prevent chassis rolling of front. 000 IFW0 IFW06G IFW06B IFW07G IFW07B IFW08 IFW09 IFW0 SP Special Servo Saver Set Ball Bearing 7 Wheel Nut (Gold) instead of 7. 7 Wheel Nut (Blue) instead of 7. 7 Wheel Hub (Gold) instead of 7. 7 Wheel Hub (Blue) instead of 7. SP 7 Special Upper Rod (Front) instead of 7. SP Special Upper Rod (Rear) instead of. PC mm PC Flywheel (mm) for -piece clutch. 800 0 0 00 00 00 00 00 IFW Rear Lower Suspension Plate Option for caster angle of rear. 00 IFW Front Torque Rod Set limits chassis rolling. 700 IFW 8, Special Radio Post instead of 8. aluminum 600 IFW 0 7 Universal Swingshaft (Rear) 0 7 in one piece. 00 OPTIONAL PARTS FOR JAPANESE MARKET ONLY. No. No. Part Names Quantity 00 IFW 9 Shock Piston.mmx Hole instead of 9. 0 00 6 IFW6BL Hard Shock Stay (F)70-7S instead of 6. 00 IFW7 TCD Gear Set Gear Set for TCD 700 IFW8 TCD Final Gear Set Diff. Gear Set for Front/Rear 0000 IFW9 TCD Center Gear Set Diff. Gear Set for Center 900 IFW0 Rear Suspension Plate (Red) For Flat Surface 00 IFWBL Hard Rear Shock Stay (70-7) 700 IFW SP Brake Disk Polished. High Strength 800 IFW SP Hard Upper Rod (Front) High Strength Replacement 000 IFW SP Hard Upper Rod (Rear) High Strength Replacement 00 IFW Spur Gear (8T) Made of Steel 00 IFW6BL Steering Plate High Strength Replacement 800 W06.8mmmm.8mm Hard Ball (w/mm hole) instead of. 00 W07 6.8mmmm9 6.8mm Hard Ball (w/mm hole) instead of 9. 00 W0 Inner Sponge (Low-hight) Install inside of tires. 00 W09 Inner Sponge (round type) Install inside of tires. 00 W66S/H S/H High-traction Tire (S/H) 000 W68S/H X High-traction Tire (X-pattern) 000 W68S-C C-GripX S C-Grip Tire (X pattern S) 00 W69S/H High-traction Tire (pin type) 000 W60SS X SS High-traction Tire (miclo X SS) 000 W60SS-C C-Grip X SS C-Grip Tire (miclo X SS) 00 W6/H Super Multi Pin Tire Same pattern as standerd kit. 000 70KP/KY M / Fluorescent Strap (M) Fluorescent Pink / Fluorescent Yellow ( )0 70 Special Antenna Holder aluminum 00 790 Color Silicone Tube 00 79 Starter Box 000 876 Fuel Filter Shuts out dirt from fuel 000 98 Air Cleaner Oil 000 9 O.S.-RZ,, Manifold (O.S.-RZ, Picco, Nova Rossi) 000 9- Manifold Spring 0 96 O.S.-RG Manifold (O.S.-RG) 000 76 6V X-FORCE 600 6V X-FORCE 600 Ni-Cd Battery for receiver 800 76 6v-000mAh 6v-000mAh Ni-Cd Battery for receiver 000 80 Special Taper Reamer Best tool for holing bodies. 800 80 & + Locking Jig & Wrench Cross wrench + plug locker. 800 809 Flywheel Wrench Wrench Set. 00 908 GP0 Muffler Joining Pipe (GP0) 0 9 Heat-resistant Muffler Joining Pipe 000 90 Loctite (medium strength) Screw cement. 900 96 One-touch Plug Heat Set booster cord, Ni-Cd battery, charger 800 96 00cc Quick Fill Fuel Bottle (00cc) aid for fueling 00

() 00 0 0 0 7 7 6 8 0 () (),00 00 80,680 () () 0 0 0 7 7 6 8 0 ()

08

Round Head Screw 0 x6 x8 x0 x each 0.6x8.6x0.6x.6x each 0 x x6 x8 x0 x each 0 x x6 x8 x0 each 0 x6 x8 x0 x each 06 x x x6 x8 each Bind Screw 0.6x.6x6.6x8.6x each x x6 x8 x0 x each x x6 x8 x0 each x6 x8 x0 x each x x x8 x0 each x x8 x0 x each Flat Head Screw 8.6x8.6x0.6x.6x each 9 x6 x8 x0 x each 0 x x6 x8 x0 each x8 x0 x x0 each x x x6 x8 each x0 x x x each Cap Screw x8 x0 x x each.6x8.6x0.6x.6x each 6 x8 x0 x x each 7 x x6 x8 x0 each 8 x x0 x x0 each 9 x0 x x0 each 0 x x8 x0 each x x0 x each x x6 x8 x0 each.6x6.6x8.6x0.6x each x6 x8 x0 x x each x x6 x8 x0 each 6 x x0 x each 7.6x.6x.6x6.6x8 each 0.6x6.6x8.6x0.6x each x6 x8 x0 x x each x x6 x8 x0 each x0 x x8 each Flat Head Self-Tapping Screw 7.6x6.6x8.6x0.6x each 8 x6 x8 x0 x x each 9 x x6 x8 x0 each 0 x x0 x each Flanged Cap Screw x6 x8 x0 each x8 x0 x each Screw 7 x8 x0 0 each Set Screw 60 x6 x x x6 each 6 x x x x0 each 6 x x x8 x each 6 x x x6 each 6 x0 x0 each Ø Nut 7 mm.6mm 0 each 7 mm mm 0 each Flanged Nut 7 mm 0 pcs 7 mm 0 pcs Nylon Nut 77.6mm pcs 78 mm pcs 79 mm pcs Flanged Nylon Nut 80 mm pcs Washer 8 mm.6mm mm 0 each 86 mm mm 0 each 80 E. 0 pcs 8 E.0 0 pcs 8 E. 0 pcs 8 E.0 0 pcs 8 E.0 0 pcs 8 E.0 0 pcs 86 E6.0 0 pcs 87 E7.0 6 pcs 90 E0.0 6 pcs FOR JAPANESE MARKET ONLY. No. No. No. No. Part Names Qty. No. Part Names Qty. No. Part Names Qty. 9660 00 00 00 Silicone Oil (00) 96607 00 Silicone Oil (00) 967 000 00 Silicone Oil (000) 0 00 000 9660 Silicone Oil (0) 96608 Silicone Oil (00) 967 Silicone Oil (000) 00 600 for shocks. 600 000 9660 Silicone Oil (00) 96609 Silicone Oil (600) 967 Silicone Oil (000) for diffs. 600 600 0 for shocks. 800 6000 9660 Silicone Oil (0) 9660 Silicone Oil (800) 9676 Silicone Oil (6000) 00 000 7000 9660 Silicone Oil (00) 96 Silicone Oil (000) 9677 Silicone Oil (7000) 600 0 000 for diffs. 96606 Silicone Oil (0) 967 Silicone Oil (000) R THE FINEST RADIO CONTROL MODELS -00 TEL.06-9- () 0 00 8 00 60007- PRINTED IN JAPAN