*Before beginning assembly, *please read these instructions thoroughly. R THE FINEST RADIO CONTROL MODELS INSTRUCTION MANUAL :8 Scale Radio Controlled Electric Powered WD Monster Truck TWIN FORCE INDEX REQUIRED FOR OPERATION RADIO PREPARATION BEFORE YOU BEGIN ARRANGEMENT OF PLASTIC PARTS ON RUNNERS ASSEMBLY OPERATING YOUR MODEL SAFELY EXPLODED VIEW SPARE PARTS & OPTIONAL PARTS 6 7 8 9 0 7 UNDER SAFETY PRECAUTIONS This radio control model is not a toy! First-time builders should seek the advice of experienced modelers before beginning assembly and if they do not fully understand any part of the construction. Assemble this kit only in places out of children's reach! Take enough safety precautions prior to operating this model. You are responsible for this model's assembly and safe operation! Always keep this instruction manual ready at hand for quick reference, even after completing the assembly. *SPECIFICATIONS ARE SUBJECT TO BE CHANGED WITHOUT NOTICE. 00 KYOSHO CORPORATION No. 0B
R REQUIRED FOR OPERATION () ch with electronic speed controller and servo radio control set CAUTION: Only use a surface radio with channels and electronic speed controller! (Any other radio is prohibited!) This kit requires a channel radio control set with electronic speed controller. Because there are stick-type and wheeltype transmitters, use which ever fits your convenience best. For more information on the radio con-trol set, refer to its instruction manual. Stick-type ch radio set Wheel-type ch radio set Servo AA-size Batteries (For Transmitter) Suitable servos, receiver & electric speed controller Receiver AA AA Electric speed controller Operation/Receiver Battery and Charger for Ni-Cd Battery Two batteries power the motors and receiver. Any of the batteries listed at right can be used. Use only the same type of batteries. Two types of chargers are available. One operates on a V car battery. The other operates on a 00V house outlet. No.790 7.V 000 7.V Sports Power Battery (Beginner class) No.7 7.V 000 7.V SPORTS POWER 000 Ni-MH Battery No.70 XAC X-CHARGER AC No.70 EXCEL PRO CHARGER Vor..0 No.7 Mulci Charger IV Electric Speed Controller 7.V.V Requires an ESC designed for two 7.V batteries (.V). Paint and Brush For painting the body, use Kyosho paints for models! PAINT BRUSH No.0 POLYCA COLOR No.760 767 KYOSHO SPRAY COLOR CAUTION: Before using spray colors, always read their explanations! FUELPROFF PAINT KY OSH O S PR AY CO LO R MICRON LINE TAPE KYOSHO No.8 (mm x m) 8 (.mm x m) 8 (.mm x m) 89 (0.mm x 8m) 860 (0.7mm x 8m) Super-flexible tape for masking and detail designing jobs. Micron Line Tape No.9670 D FLEX COLOR DECAL Self-adhesive super-flexible sheets that bond to polycarbonate - even when applied to curved surfaces. No.97 MASKING SHEET For safe masking jobs, use this plastic masking sheet featuring one self-adhesive edge.
REQUIRED FOR OPERATION () 6 Tools required Phillips Screwdriver (L.M.S) Needle Nose Pliers Screw Cement CAUTION: Handle tools carefully! Sharp Hobby Knife Wire Cutters Rubber Cement TOOLS INCLUDED Hex Wrench (.mm, mm,.mm, ) Awl KYOSHO KYOSHO Special Glue Instant Glue No.96 Special Glue Cross Wrench No.690 Knife REAMER No need to pre-drill! Drills neat mm to mm holes directly! No.89 ROUND CUTTER & SANDER For trimming bodies! Cutting along curved lines never was so easy! A new battery must be charged before it is used. Refer to the charger instruction manual for charging. Set up the radio control system as indicated below. RADIO PREPARATION Battery x Charger Electronic Speed Controller 6 0 ON OFF 7 9 ON OFF 8 8 6 7 8 6 0 ON OFF Transmitter Servo START Receiver 6 7 8 Install batteries. (Transmitter) Extend the antenna. (Transmitter) Connect the battery. Extend the antenna. (Receiver) Center the trims. Switch on. (Transmitter) Switch on. (Receiver) Switch Make sure the servos are in command. 9 0 FINISH 9 0 Switch off. (Receiver) Switch off. (Transmitter) Retract the antenna. (Transmitter)
BEFORE YOU BEGIN () Read through the manual before you begin, so you will have an overall idea of what to do. Check all parts. If you find any defective or missing parts, contact your local dealer or our Kyosho Distributor. How to read the instruction manual: Front Suspension x 0mm Metal Bushing No., No., No.6 This instruction manual uses several symbols. Please note them during the entire assembly. King Pin 6 6.8mm Pillow Ball (Black) R 7 L 8 Key Number, Part Name, True-to-scale Diagram, Quantity Used All parts except screws are identified by key numbers. For purchasing spare parts, find the key no. of the part needed in the spare part list and refer to the left column to look up the corresponding order no. Symbols used throughout the instruction manual, comprise: Part bags used. mm Drill holes with the specified diameter (here: mm). Must be purchased separately! Apply instant glue (CA glue, super glue). Cut off excess. Pay close attention here! Apply grease. Cut off shaded portion. Assemble in the specified order. Apply threadlocker (screw cement). Tentatively tighten. True-to-scale diagram. x Assemble as many times as specified (here: twice). Ensure smooth non-binding movement while assembling. Assemble left and right sides the same way. Apply rubber cement.
BEFORE YOU BEGIN () This kit contains screws and hardware in different metric sizes and shapes. Before using them, check the screws on the true-to-scale diagrams on the left side in each assembly step. Some screws are extras. SCREWS OTHER HARDWARE Screw Self-tapping (TP) Screw Screw Washer Nut E-ring Cap Screw TP F/H Screw mm Flat Head (F/H) Screw Set Screw F/H Screw Metal Bushing Bearing mm Pillow Ball mm 0mm 6.8mm 6 Self-tapping (TP) screws cut threads into the parts when being tightened. Excessive force may permanently damage parts when tightening TP screws. It is recommended to stop tightening when the part is attached or when some resistance is felt after the threaded portion enters the plastic. Correct Wrong Overtightened. The threads are stripped. MEMO
ARRANGEMENT OF PLASTIC PARTS ON RUNNERS () No. 0 0 9 No. 77 76 No. 8 6 7 9 9 6
ARRANGEMENT OF PLASTIC PARTS ON RUNNERS () No. 0 0 No.7 79 9 9 No.6 0 Shaded Parts are not used. 97 96 97 97 0 0 97 0 99 98 00 7
6 Parts are pre-assembled in step ~ 6. Gear Differential x mm Set Screw x 0mm Shim 6 6mm O O-ring 8 8 x 6mm Ball Bearing.6 x mm Shaft (Black) xmm 6 9 0 0 x Gear Differential Diff. Oil x 0mm TP TP F/H Screw 8.6 x mm Shaft (Black) 8 x 6mm 6 Ball Bearing 8 x0mm 6 6mm O O-ring x Front Axle.6x6mm.6x0mm.6x6mm 7.6x6mm.6 x 0mm Screw.6 x 6mm Screw 7 Short 8 x 6mm Ball Bearing x 6mm Shim (Thick) Long Assemble in the specified order. Apply grease. x Assemble as many times as specified. Must be purchased separately! 8
Front Suspension Arm F Marked F x0mm A Marked A Install a setscrew on the flat surface. 7, 8 Pay attention to the direction of 7 & 8. Wide Narrow Up xmm x0mm B 6 Marked B 9 7 8 9 F Marked F x0mm Short x 0mm TP Long TP Screw x mm x0mm Pay attention to the lengths. Set Screw 9 6 The angle of 9 must be as shown in the drawing. Joint Cup Use the correct hole. Up Front F 9 8 B F Rear Axle 7 Long.6x0mm.6 x 0mm Screw.6 x 6mm Screw 7 8 x 6mm Ball Bearing x 6mm Shim (Thick) Short.6x6mm.6x6mm.6x6mm Pay close attention here! Assemble in the specified order. Apply threadlocker (screw cement). 9
6 Rear Suspension Arm R Marked R x0mm A Marked A 7, 8 Pay attention to the direction of 7 & 8. Wide Up Narrow xmm 7 Install a setscrew on the flat surface. 6 x0mm B 8 B Marked B x 0mm x0mm TP 6 TP Screw Joint Cup Long Short R Marked R x mm Set Screw Pay attention to the lengths. x0mm R START 7 Shock No. 6 0mm 6 OO-ring (M) 9 Shock End 7 9 Put a little oil. Pinch to avoid scratching the shock shaft. x 8 Shock Keep expanded. No. Insert the shaft slowly. Put the oil. Tighten the cap until it slightly stops, then loosen it for a /nd lap. Tighten the cap firmly, and pull the shaft. 0 Surplus oil comes out. Part bags used. Apply threadlocker (screw cement). Pay close attention here! x Assemble as many times as specified. 0
9 Shock No. x 7.8mm Ball For adjusting the spring tension. exists in widths. For making the F / R ground clearance horizontal, choose the necessary width(s) and amount of. When adjusting, run your car. Compress the spring and install. 0 Servo Saver No., No. 9 x mm Flanged Nut Rod 0 x 6.8mm Rod Pillow Ball (silver) x 7.mm 7.8mm Shaft Ball End 8 Servo Saver Spring Saver Nut Saver Shaft x mm Cap Screw 7 9 Short 7 xmm 6 Note the direction. mm approx. mm 6 6 7 0 Long 7 8 mm 8 approx. Part bags used. Apply threadlocker (screw cement). x Assemble as many times as specified.
Gearbox No., No. xmm x mm Screw x 8mm Screw x 0mm TP TP Screw 0 x mm Set Screw.6 x 6mm Pin Joint Cup x0mm 7 x0mm 8 xmm 6 9 7 0 x0mm x0mm 6 Center Shaft 6 6 x x mm Ball Bearing 8 x 6mm Ball Bearing 6 7 Note the direction. 0 Drive Chain 8 9 6T Sprocket x0mm x8mm x8mm x0mm Part bags used. Apply threadlocker (screw cement). Assemble in the specified order.
Gearbox xmm 60 Hook the Drive Chain on 60 Sprocket. 6 xmm No. x 0mm TP TP Screw x mm Set Screw 60 Drive Chain 6 6 6 6 6 x x mm Ball Bearing x0mm Main Gear No. mm Flanged Nylon Nut 68 6 x 0 x Metal Bushing 69 67 66 7mm approx. 7mm 68 67 6 66 6 mm 69 67 Install 67 to the indented part of 69. Motor No. x 8mm Cap Screw x Set Screw Washer Gears should engage firmly, leaving a gap only wide enough to insert a piece of paper. 7 x8mm x 70 x8mm Part bags used. Apply threadlocker (screw cement). Assemble in the specified order. Assemble left and right sides the same way. Ensure smooth, non-binding movement when assembling.
Side Plate < > < Right > 7 No.6 Note the direction. 7 7 The flat surfaces of parts 7 must rest against part 7. Front 7 x8mm < > < Left > 7 x 8mm Cap Screw x8mm x 0mm Cap Screw 7 Chassis Joint 7 x0mm 7 Note the direction. x0mm 7 6 Battery Box No.7 < > < Right > Front < > < Left > x 8mm F/H Screw 7 Flanged Nut x8mm x8mm Part bags used. Tentatively tighten. Assemble left and right sides the same way. Pay close attention here! Apply threadlocker (screw cement).
7 Side Plate x 0mm Cap Screw x0mm Main Chassis For Right x0mm For Left Front x0mm x0mm Attach the side plates to the main chassis by installing the six x0mm cap screws. Screw them in completely and use screw cement. 8 Steering Servo 77 No., No.7 x0mm xmm 76 Steering Servo xmm x0mm x0mm 0mm approx. 0mm x0mm x 0mm TP TP Screw 6 mm approx. mm 78 Supplied with the servo. mm 90 Servo horns by any manufacturer should be cut as shown in the drawing. 78.8mm Pillow Ball (Black) x mm TP F/H TP Screw Part bags used. Apply threadlocker (screw cement). mm mm Drill holes with the specified diameter. Cut off shaded portion. Must be purchased separately! Assemble in the specified order. Assemble left and right sides the same way.
9 Radio No.7 x0mm x0mm 79 x 0mm TP TP Screw 0 Radio No.7 Be careful to avoid mixing up the and leads..v.v Electronic Speed Controller 90 Double-sided Tape Receiver 90 Double-sided Tape Part bags used. Must be purchased separately! Pay close attention here! Assemble left and right sides the same way. 6
Radio x 8mm Screw mm Nut x 0mm TP TP Screw No.7 Included with the switch. x8mmmm If screws are not included with the switch, use a x8mm screw and a mm nut. Included with the switch. Antenna Switch 9 x0mm Cords come like picture. Connect as per radio instruction manual. 9 If the wire is too short, use extension wire available from your radio manufacturer. Bind the wires with strap. 9 Radio No.7 9 9 Hook Pin 9 9 9 Be careful not to snag the wires. Remove when the heat protector of your ESC is used. Part bags used. Must be purchased separately! Pay close attention here! 7
Front Bumper No.6 97 x8mm 98 x8mm 98 Use the lowest hole. x8mm xmm x 8mm TP TP Screw 97 x mm Screw 96 xmm Wheelie Bar No.6 x8mm 99 xmm 0 xmm 0 0 99 x8mm 00 0 x8mm Use the lowest hole. 97 xmm x 8mm TP TP Screw x mm Screw xmm Flanged Nut 0 Aluminum xmm Part bags used. 8
Front Suspension No. 8 x 6mm Ball Bearing < > < Right > 06 R R maked. 06.6 x.8mm Pin 09 7 6mm Flanged Nut 7 0 07 Note the direction. 08 < > < Left > L L maked. 0 6 Front Suspension No. x mm Cap Screw Knuckle Collar For Front xmm Long xmm F F maked. For left side. For right side. F xmm Long Short Short xmm Pay attention to the lengths. Part bags used. Assemble left and right sides the same way. Assemble in the specified order. Pay close attention here! Tentatively tighten. 9
7 Steering 8 7 Short No. 7 9 Long 7 approx. x 7 78mm approx. 78mm 6.8mm Pillow Ball (silver) 7.8mm Ball End mm approx. mm 6 6 mm approx. mm 6 6 6 8 x mm Rod 9 x 9mm Rod 6 mm approx. mm 8 Steering No. x8mm x 8mm Cap Screw Washer Short x8mm Long 6 Short 6.8mm Pillow Ball (silver) 6 x. x 8.mm Collar 6 6 R R maked. Flanged Nut 6 L L maked. F F F maked. Long Short Pay attention to the lengths. Part bags used. x Assemble as many times as specified. Ensure smooth, non-binding movement when assembling. Apply threadlocker (screw cement). Pay close attention here! 0
9 Front Suspension No.6 x mm Cap Screw 7 Suspension Pivot Flanged Nut x 0 x mm Washer xmm 7 7 xmm 8 0 Front Shock Push on marked side first. Shocks Shocks x 0mm Screw x0mm Nylon Nut Use this hole. Part bags used. Assemble in the specified order. Assemble left and right sides the same way. Apply threadlocker (screw cement).
Rear Suspension No. 8 x 6mm 06.6 x.8mm Ball Bearing Pin 7 6mm Flanged Nut x 0 xmm 0 0 6.8mm 9 6.8mm L x mm Ball End (L) Ball Cap Screw 9 0mm approx. 0mm 9 x mm Set Screw < > < Left > L L maked. 06 0 < > < Right > 09 R R maked. 08 7 0 07 Note the direction. xmm Rear Suspension No. x mm Cap Screw x mm Cap Screw Knuckle Collar For Rear Short xmm R R maked. xmm R Long Short xmm xmm For right side. xmm For left side. xmm Long Pay attention to the lengths. Part bags used. x Assemble as many times as specified. True-to-scale Assemble left and right Assemble in the diagram. sides the same way. specified order. Pay close attention here! Tentatively tighten.
Rear Suspension No. x mm Cap Screw 7 Suspension Pivot Flanged Nut x 0 x mm Washer xmm 7 7 xmm 8 Rear Shock Push on marked side first. Shocks Shocks x0mm x 0mm Screw Nylon Nut Use this hole. Part bags used. Assemble in the specified order. Assemble left and right sides the same way. Apply threadlocker (screw cement).
Assemble wheels for the left and wheels for the right side. Wheels < > Note the < > < Left > direction. < Right > Apply rubber cement and install in tires. x x Note the direction. Sand the gilding from the shaded portion of the wheels. x mm Make two mm holes. mm mm mm Make two mm holes. mm mm 6 Wheels For right side. For left side. For right side. 7 7 For left side. Remove when adjust. mm x Apply instant glue mm Drill holes with the Assemble as many (CA glue, super glue). specified diameter. times as specified. Assemble left and right sides the same way. Pay close attention here! Apply rubber type glue.
7 Body Shell 7mm 6mm 7mm 8 Painting Before painting, use a neutral detergent to remove any oil residues and dirt. Mask the windows from the inside. Refer to the pictures on the box for the color scheme. Paint the body shell from the inside using Kyosho s spray colors. Mask Windows After painting, remove the protective film from the body shell. Mask Windows Cut off shaded portion. 7mm 7mm Drill holes with the specified diameter.
9 Decals Apply the decals to the positions indicated in numerical order. The decal numbers between brackets are only for the opposite side. Refer package for applying decals which with out number. 6 7 8 9 6 7 0 ( ) ( ) 0 Battery No.7 x 0mm TP TP Screw 9 Hook Pin x0mm Battery Lift and install the battery. 9 x Part bags used. Must be purchased separately! Assemble in the specified order. x Assemble as many times as specified. 6
Body Shell 6 Body Pin 6 Slightly bend the body pins as shown in the diagram for easier removal. 6 6 6 Safety Precautions Always run your car with the body shell fitted! Avoid changing the running direction too often and too abruptly. Do not run your car on ground: that is overgrown with grass. that is muddy, sandy or rocky. Check all screws, nuts etc. on a regular basis for looseness. Gear Ration Table Pinion 7T 8T 9T 0T Gear Ratio.98 :.7 : 0.6 : 9. : Speed Slow Fast Accelaration Quick Slow Run Time Long Short * * Use the same pinion gear if you convert the motor pinion gear. < Motor >.V 7.V The motor life for this.v vehicle is shorter than that of a 7.Vpowered model. Therefore we recommended upgrading the motors if you find that speeds are too slow or the batteries lose power too quickly. / Inciuded in this kit. < Battery > 7.V Make certain that both batteries are fully charged. Otherwise performance may drop or overheating could result. Part bags used. 7
HOW TO ADJUST THE SLIPPER CLUTCH mm Referring to the illustration, adjust the Slipper Clutch with the mm Nylon nut. Adjust when running. mm If the slipper clutch slips too much and the car does not start off, tighten the mm nylon nut. mm If the slipper clutch does not slip at all, Loosen the mm nylon nut. * As a thumb rule, set the slipper clutch to slip a little from a dead stop. * The more the slipper clutch slip, the more heat is generated. The longer you run under such circumstances, the more likely you will damage the spur gear. * Do not operate without a slipper clutch. Otherwise, the gear will be damaged. 7mm approx. 7mm mm Flanged Nylon Nut Tighten Loosen MAINTENANCE Note the following in order to ensure smooth operation and long life of the -Speed Transmission. Lubricate the ball bearings to ensure smooth operation. Regularly check whether the screws on the chassis are firmly tightened, and retighten if necessary. Regularly check whether the oneway bearing locks into the direction indicated. If it does not lock, replace the shaft or oneway bearing. Keep the gears clean from dirt and sand to prevent damage. 8
BSW7 Instructions for installing the BSW7, Turbo Big Shock. Before installing, remove all relating parts on the chassis first. < > < Front > No.8 xmm Ensure that you use the correct holes. No.W0 x6xmm x6xmm Aluminum Collar No.7 Flanged Nut No.IF7- Antiribration Rubber Use kit original. No.78 Nylon Nut No.BSW7 Turbo Big Shock No.W0V x6mm x6mm Tapered Washer Use kit original. < > < Rear > No.8 xmm Ensure that you use the correct holes. No.W0 x6xmm x6xmm Aluminum Collar No.7 Flanged Nut No.IF7- Antiribration Rubber Use kit original. No.78 Nylon Nut No.BSW7 Turbo Big Shock No.W0V x6mm x6mm Tapered Washer Use kit original. IF, IF06 Instructions for installing IF and IF06. Use kit original. No.IF06 8mm 8mm Bevel Gear No.IF T Drive Bevel Gear (T) Use kit original. Must be purchased separately! Assemble left and right sides the same way. 9
OPERATING YOUR MODEL SAFELY WARNING: Do NOT operate the model in the following places and situations: (Non-observance may lead to accidents!) Operate the model in spacious areas with no people around! Do NOT operate it:. on roads!. in places where children and many people gather!. in residential districts and parks!. indoors and in limited space! * Non-observance may account for personal injury and property damage! Always check the dry batteries in the radio! When the dry batteries get weaker, transmission and reception of the radio decrease. You may lose control of your model when operating it under such condition. This may lead to accidents! Keep in mind that people around you may also operate a radio control model! NEVER share the same frequency with somebody else at the same time! Signals will be mixed and you will lose control of your model. 0 This may lead to accidents! When the model is behaving strangely...! Immediately stop the model and check the reason. As long as the problem is not cleared, do NOT operate it! This may lead to further trouble and unforeseen accidents! WARNING: in order to avoid accidents and personal injury, be sure to observe the following: Do NOT put fingers or any objects inside rotating and moving parts! Rotating / moving at high speed, you may be seriously injured! After operation, the electric motor and battery are hot! You may burn yourself seriously touching them! Before charging, please carefully read the explanations of the battery and charger unit! While charging, the battery and charger unit get hot! NEVER charge on top of or near easily inflammable material as this will result in fires! NEVER short out batteries!. Do NOT disassemble or modify batteries!. Ensure the cords do NOT trail into rotating and moving parts! Batteries use heavy metals that are noxious to health! NEVER throw them into fires as they will explode! ALWAYS return disused batteries to the shop! Do NOT dispose of them into the usual waste stream! 0
< EXPLODED VIEW > Gear Differential IF9 8 IF0 BRG00 IF0 6 ORG06 IF0 9 BS07 IF0 0 IF0 IF0 IF9 6 ORG06 Front / Rear BRG00 MA00 8 IF0 Shock MA06 0.6mm Nut 8 7 6 BSW77 MA06 9
TWIN FORCE 00 KYOSHO CORPORATION / < > EXPLODED VIEW Note that some parts are not sold as spare parts! E F C C D D E M J K G H H B A G M N L K I I J Gear Diff Gear Diff Shock Shock Shock Shock A B N L F MA0 8 MA00 MA0B 76 8 6 MA0 MA0 6 MA00 60 MA0 MA0B BS9 0 8 6 8 6 LA 7 7 8 6 MA0B MA0 MA0 7 BS MA 0 MA0 6 MA08 6 BS MA06 7 MA0 7 MA0 9 OT6 78 LA 7 LA 7 8 6 MA0B MA0B 77 MA00 7 MA0 8 8 6 8 6 MA0B 6 LA 7 LA 7 LA 7 BS MA0B MA00 MA00 7 LA 7 MA0 9 MA00 8 MA 6 MA06 7 MA08 9 MA08 MA0B 7 MA0B 7 BRG006 6 IF 8 BRG00 MA0 0 IF 8 MA08 7 MA08 8 MA07 0 MA06 MA0 6 FM8 MA 6 BRG00 MA008 BRG00 BRG00 IF7 IF7 MA 7 MA 7 8 6 MA0B 6 MA0 MA09 7 MA09 7 MA0 MA0 MA0 MA0B 97 MA0B 98 MA0B 96 FM9 6 06 BRG00 MA08 MA08 0 MA07 07 06 MA08 MA0 BRG00 BS6 0 96 9 BS6 0 96 9 IF7 MA0 7 MA00 7 MA06 09 MA00R MA08 0 MA07 07 BRG00 BS9 0 IF7 MA0 MA0 MA09 7 MA0 MA0B 99 MA0B 97 MA0B 00 MA0B 0 MA0B 0 MA0B 0 FM9 6 MA09 7 MA0 MA00 MA00 BS MA00 7 BS MA0 BRG00 MA6 09 MA00F 9 MA00F 9 BS6 0 MA0 7 MA00 8 MA00R MA09 MA09 7 9 MA06 7 MA08 9 MA06 7 9 96 90 96 90 MA0 9 708 9 9 9 MA0 79 MA0 9 700 9 MA06 66 MA0 8 MA-8 70 MA 7 BRG006 6 MA08 7 MA-8 70 MA0 69 MA0 67 FM 6 MA0 67 MA0 68 MA06 66 MA07 6 BS9 08
No. Part Names No. Quantity MA00 Front Differential Bevel Set 7 x MA00 Differential Hosing x MA00 Suspension Arm Set 7 8 x MA00F Front Hub Carrier 9 x MA00R Rear Hub Carrier x MA00 T Sprocket (T) 60 x MA0 Servo Saver Shaft Set 8 x MA0B Steering Crank Set 76 77 x 9 0 9 x 8 x MA0 Steering Rod Set 7 x 0 9 x MA06 Sprocket Shaft x 8x6mm x 8x6mm Washer MA07 Drive Chain 0 x SPARE PARTS 80 7 80 788 788 60 60 80 0 80 MA08 Oneway Cup Joint 7 x 60 MA0B Side Plate 7 x 00 MA0B MA0,96 98 99 00 0 0 x Bumper, Body Mount Set 0 x 97 x L=mm Swingshaft (L=mm) x 00 60 MA0 Beam Pivot 7 x x0mm x0mm Washer x MA08 Body Set x Masking Sheet 90 MA0 / Tire / Inner x 0 MA0 Wheel x 9 MA06 Wheel Shaft 09 x 68 MA07 Wheel Stopper 07 x 78 MA08 Wheel Spacer 0 06 x 68 MA09 Wheel Nut 7 x 0 MA06 6 7 8 9 0 Shock Set x 99 MA06 Shock Pivot 7 x MA00-0 Decal Set (TWIN FORCE) decals x 70 MA0 EP Under Plate (EP) 6 x 60 MA0 Motor Mount 8 x 78 MA0 Top Gear Shaft 6 6 x MA0 Main Gear 68 69 x 68 MA0 Slipper Sheet 67 x 89 MA06 Slipper Plate 66 x 68 MA07 Spring Collar 6 x 89 MA08 Center Bulk Set 8 9 7 9 6 x 7 MA09 Battery Box Set 7 x MA0 Radio Box Set 79 9 9 x 7 MA 8T -8 Steel Pinion Gear (8T) 70 x 99 MA LL Joint (LL) 6 x 68 MA Chassis Joint Set 0 x 7 x 60 MA 7 x Motor (Monster 0) 6 0 No. BS9 Part Names Front Hub BS Swingshaft 6.8mm BS6 6.8mm Ball BS Shim BS07 Bevel Shaft BSW77 Adjuster Collar FM9 Body Pin FM8 Joint FOR JAPANESE MARKET ONLY. No. Quantity x 0 x 0 x 9 x 6 6 x (6 types.) 6 x 0 x 7 0 6 67 78 8 60 FM Clutch Spring 6 x IF7 Knuckle Arm Collar x 80 IF0- IF9 Differential Case Packing.6xmm.6xmm Shaft x x 0 7 89 IF0 Differential Shaft Set 8 x 788 IF0 Differential Bevel Set x 0 x 0 IF0 Differential Case x IF Center Shaft (Rear) 8 x 7 LA.8mm.8mm Ball End 7 x ORG06 OP6 Silicone O-ring (P6/Orange) 6 x 0 OT6 8 96 700 KP/KY 708 968.6mm.6mm Pillow Ball.8mm.8mm Pillow Ball 6.8mm 6.8mm Ball End S Fluorescent Strap (S) Color Antenna (Black Cap) Snap Pin 08 0 x 78 x 0 6 x 8 9 x 9 x 8 9 x 9 x 0 96 Double-sided Tape 90 x BRG00 8x6x Shield Bearing (8x6x) x BRG006 6xx Shield Bearing (6xx) 6 x 68 0 0 89 0 68 00 Some of the parts included are not available as spare parts. Purchase optional parts instead.
OPTIONAL PARTS No. No. Part Names Quantity MA0 x x Body Set (MAD ARMOUR) Body Masking Sheet 60 0 MA0 x -0 Decal Set (MAD ARMOUR) Decals MAW00 7T -7 Aluminum Pinion Gear (7T) Light weight, Aluminium 0 MAW00 9T -9 Aluminum Pinion Gear (9T) Light weight, Aluminium 0 MAW00 0T -0 Aluminum Pinion Gear (0T) Light weight, Aluminium 0 MAT00 Tire (Twin Rib) 8 MAW00B Hard Polish Side Plate MAW00 Ultra Soft Spring Spring Set for Double Damper ( pcs.). 60 MAW006 SP Special Steering Rod Set Hard Aluminum Type (complete set). 00 MAW009 Aluminum Seering Crank Aluminum made (complete set). 70 BSW7 L Turbo Big Shock (L) 990 IF7- Anti-Vibration Rubber 0 W0 Aluminum Collar 7 W0V x6mm x6mm Tapered Washer Use Together 7 8 xmm xmm Cap Screw 0 7 Flanged Nut 0 78 Nylon Nut 0 IF T Drive Bevel Gear (T) Use Together 60 IF06 8mmT 8mm Bevel Gear (T) 6 IFWBL L Spring (L) Blue Medium pcs. 9 IFWGR L Spring (L) Green Soft pcs. 9 IFWR L Spring (L) Red Super Soft pcs. 9 IFWW L Spring (L) White Hard pcs. 9 IFW R, 8 Universal Center Shaft (Wide R) instead of, 8. 890 IFW7 LSD TCD Gear Set 787 IFW7-0 LSD TCD Gear Oil LSD For TCD Gear. IFW8 LSDLSD TCD Final Gear Set 000 Includes TCD Gear Set, Diff. Case and Final Bevel Gear (complete differential). FOR JAPANESE MARKET ONLY. No. No. Part Names Quantity.8mm W00.8mm Steel Ball 7 0 W0 7 Tapered Washer W06 Flat Head Washer W06G Flat Head Washer (Gold) 776 Pit Box / 0x0x0mm Size / 0x0x0mm 70 89 Hobby Shears & Sander Handy tool for round cut. 00 7 7.V 000 Ni-MH 7.V Sports Power 000 Ni-MH Battery Large capacity Ni-MH Battery. 67 7.V 000 790 7.V Sports Power 000 Ni-Cd battery 00 80 Special Taper Reamer Best tool for holing bodies. 890 90 90 LSD TCD Gear Oil Loctite (medium strength) Screw cement. 60 9 96 Silicone Seal 80 96 KYOSHOg KTOSHO Special Glue (g) Instant Glue 7 96 KTOSHO0ml KTOSHO Special Primer (0ml) 00 966 Ring Gear Grease 0 960 Power Cleaner 80 966 SP Special Bearing Liquid Retrieves potentiality of Bearing. 00 9698 Molybdenum Coat 680 690 Knife Edge Reamer To drill holes of the body. 00
SCREW NUT etc. No. 0 0 0 0 0 06 0 8 9 0 6 7 8 9 0 mm Size (mm) Round Head Screw x6 x8 x0 x.6x8.6x0.6x.6x x x6 x8 x0.6x6.6x8.6x0.6x 7 7 mm.6mm mm 0 each 0 each x x6 x8 x0 x x6 x8 x0 x x x x6 x8 x0 x x6 x8 x0 Flanged Nut 00 x6 x8 x0 x x x x6 x8 6 7 x x0 x.6x.6x.6x6.6x8 7 7 mm 0 each 0 each Bind Screw.6x.6x6.6x8.6x x x6 x8 x0 x x x6 x8 x0 x6 x8 x0 x x x x8 x0 x x8 x0 x Flat Head Screw.6x8.6x0.6x.6x x6 x8 x0 x x x6 x8 x0 x8 x0 x x0 x x x6 x8 x0 x x x Cap Screw x8 x0 x x.6x8.6x0.6x.6x x8 x0 x x x x6 x8 x0 x x0 x x0 x0 x x0 x x8 x0 x x0 x QUANTITY 00 00 00 00 each each each each each each each each No. 0 7 8 9 0 7 60 6 6 6 6 Round Head Self-Tapping Screw.6x6.6x8.6x0.6x x6 x8 x0 x x x x6 x8 x0 x x0 x x6 x8 x0 x8 x0 x x8 x0 mm Size (mm) Bind Self-Tapping Screw.6x6.6x8.6x0.6x x6 x8 x0 x x x x6 x8 x0 x0 x x8 Flat Head Self-Tapping Screw Flanged Cap Screw 00 Flat Head Screw Set Screw x6 x x x6 x x x x0 x x x8 x x x x6 x0 x0 QUANTITY 00 00 Nylon Nut 00 77 78 79.6mm mm Flanged Nylon Nut 00 00 80 mm each each 00 0 each 00 each each each each each No. 8 86 80 8 8 8 8 8 86 87 90 E. E.0 E. E.0 E.0 E.0 E6.0 E7.0 E0.0 FOR JAPANESE MARKET ONLY. mm QUANTITY Nut 00 Washer mm.6mm mm mm E E-Clips 00 0 each 0 each 0 0 each 0 each 0 each 0 each 0 each 0 each 0 each 6 each 6 each 6
No. No. Part Names Qty. SIL000 00 Silicone Oil (00) SIL00 SIL000 SIL00 SIL000 SIL00 SIL000 SIL00 0 Silicone Oil (0) 00 Silicone Oil (00) 0 Silicone Oil (0) 00 Silicone Oil (00) 0 Silicone Oil (0) 00 Silicone Oil (00) 0 Silicone Oil (0) 00 SIL000 Silicone Oil (00) 0 SIL00 Silicone Oil (0) for shocks. 60 0 Oil No. No. Part Names Qty. 600 SIL0600 Silicone Oil (600) 700 SIL0700 Silicone Oil (700) 800 SIL0800 Silicone Oil (800) 900 SIL0900 Silicone Oil (900) 000 for shocks. SIL000 Silicone Oil (000) 60 00 SIL00 Silicone Oil (00) 00 SIL00 Silicone Oil (00) 00 SIL00 SIL000 Silicone Oil (00) 000 Silicone Oil (000) SIL000 000 Silicone Oil (000) for diffs. 0 FOR JAPANESE MARKET ONLY. No. No. Part Names Qty. 000 SIL000 Silicone Oil (000) 000 SIL000 Silicone Oil (000) 6000 SIL6000 Silicone Oil (6000) 7000 SIL7000 Silicone Oil (7000) 0000 SIL0000 Silicone Oil (0000) 0000 for diffs. 60 0 SIL0000 Silicone Oil (0000) 0000 SIL0000 Silicone Oil (0000) 0000 SIL0000 Silicone Oil (0000) 0000 SIL0000 Silicone Oil (0000) 00000 SIL00000 Silicone Oil (00000) 7
R THE FINEST RADIO CONTROL MODELS http://www.kyosho.co.jp/ 0-00 06-9- () 0 00 8 00 690- PRINTED IN JAPAN