Dimensional Accuracy of Thermoplastic Impression Material Adaptol Part 1. Influence of Handling Temperature of Impression Material Goro Nishigawa, Masanori Yanagihara, Kiwamu Ando, Masaki Inoue, Toru Ueyama, Kinji Uchida, Kazuhiko Ogata and Takashi Sato Abstract: A thermoplastic impression material Adaptol (J.F. Jelenko & Co.) is used for the impression of denture and has attained good results. But the accuracy of the impression material is not distinct. The purpose of this study was to investigate the influence of handling temperature on dimensional accuracy of the impression material. Part 1. Impressions were made with Adaptol and custom trays. Accuracy of the impression material was determined by measurement of impressions kept in water at 5, 10, 15,20, 25 and 30 Ž. Part 2. After pouring the stone, impressions were placed into water for cooling or left in air. The temperature of water were 5, 10, 15 and 20 Ž, and the temperature of air was 25 Ž. Stone casts were made with each temperature. Accuracy of the impression material was determined by measurement of stone casts made from impressions. The following results were obtained. 1. Changing the temperature of water for keeping, impressions also changed its size. Using water at 20 Ž for keeping, the impression material indicated best accuracy. 2. As there was no significant difference between measured values of stone casts, the heat evolved at the setting of the stone indicated no influence on accuracy of the impression material. Key words: Adaptol, impression material, handling temperature, dimensional accuracy Department of Removable Prosthodontics, Okayama University Dental School (Chief: Prof. Takashi Sato)
56 316 補 綴誌 32巻2号(1988) 図2 図1 天 然 樹 脂 系 印象 材Adaptol(チ 本 研 究 はAdaptol使 ス テ ン レス製 金 型 ュー ブ 入 り) 用 時 の温 度条 件 が,印 象 精 度 に 及 ぼす 影 響 につ いて 検 討 を加 え る こ とを 目的 と して 以 下 の 実 験 を行 った. 材料 お よび 方 法 印象 材 と して はAdaptol(Jelenko社)の り(図1)を チ ュー ブ入 使 用 し,被 印象 体 と して は上 顎 無 歯顎 臼歯 部 を想 定 した ステ ン レ ス製 金 型(図2)を 用 い た.金 型 の寸 法 は 図3に 示 した通 りで あ り,基 底 面 には2個 の測 定 点 が50mmの 間 隔 で刻 み 込 まれ て い る.寸 法測 定 装 置 として は読 取 顕 微 鏡(PRM-3XYZ,ピ カ精 工 社)を 使 用 した.こ れ らの材 料 な らび に測 定 装 置 を用 い て 以 下 の 実 験 を行 った. 実 験1. 印象 の 寸 法 変 化 の検 討 図3 ス テ ン レス製 金 型 の寸 法(単 位:mm) 被 印象 体 は金 型 の基 底 面 と し,ト レー は厚 さ5mm, スペ ーサ ー2mmと して即 時 重 合 レジ ンにて 作 製 した. 印象 採 得 の各 段 階 にお け る印 象 材 の温 度 の規 定 は ウォ ー 度 を5,10,15,20,25,お よび30 の6種 類 に変化 させ た.各 保 存 温度 で10分 間 係 留 した後 に,そ れ ぞれ の 保 タ ー バ スお よ び サ ー ミスタ デ ジ タル 温 度 計(TD- 温 度 にお け る印象 面 上 の2個 の測 定 点 間 の 距 離 を読 取 顕 302,芝 浦 電 子 製 作所)を 用 いて 温 水 中 にて 行 った.そ の 微 鏡 を用 い て 計測 した.な お,試 料 は 各 保 存 温 度 につ い 各 段 階 に お け る印 象材 の温 度 と操 作 時 間 は 以 下 に示 す 通 て4個 ず つ,計20個 作 製 した. りで あ る. 1) チ ュ ー ブ入 り印象 材 の軟 化:500C 15分 2) トレーに盛 った印 象 材 の軟 化:42,43,44,45, 間 46 10分 間 3) ト レー の圧 接:37 4) 印象 の冷 却:10 実験2. した.ト 10分 間 10分 間 な お,印 象 の撤 去 は 金 型 の基 底 面 に 対 し垂 直 な方 向 に 行 った.金 型 か ら撤 去 した 印象 は水 中に保 存 し,保 存温 石 膏模 型 の寸 法 変 化 の検 討 被 印 象 体 は 図2に 示 した ステ ン レス製 金型 の顎 堤 側 と レー は厚 さ5mm,ス ペ ーサ ー2mmと して 即 時 重 合 レジ ンにて 作 製 した.印 象 採 得 時 お よ び 印象 保 存 時 の温 度 条 件 と して は,ト 44 レー に盛 った 印 象材 の軟 化 は で10分 間,印 象 の保 存 は20 そ の他 の条 件 は 実験1と 同 様 と した. で10分 間 と し,
1) Woelfel, J.B.: Contour variations in impressions of one edentulous patient, J Prosthet Dent, 12: 229 `254, 1962. 4) Kaye, N.G.: Physiologic Adaptol impressions, 29 `48, J.F. Jelenko & Co, Inc, New York, 1944.