Before commencing assembly, please read these instructions thoroughly. THE FINEST RADIO CONTROL MODELS R INSTRUCTION MANUAL Super Eight GP LANDMAX WD PEUGEOT 06 WRC INDEX REQUIRED FOR OPERATION RADIO PREPARATION BEFORE YOU BEGIN ARRANGEMENT OF PLASTIC PARTS ON RUNNERS ASSEMBLY ADJUSTMENT OPERATING YOUR MODEL SAFELY EXPLODED VIEW SPARE PARTS & OPTIONAL PARTS 6 7 8 7 7 0 7 SAFETY PRECAUTIONS This radio control model is not a toy! First-time builders should seek the advice of experienced modellers before commencing assembly and if they do not fully understand any part of the construction. Assemble this kit only in places out of children's reach! Take enough safety precautions prior to operating this model. You are responsible for this model's assembly and safe operation! Always keep this instruction manual ready at hand for quick reference, even after completing the assembly. *SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE. 00 KYOSHO No. 7
R R REQUIRED FOR OPERATION () ch radio control set with servos. This kit requires a channel radio con-trol set with servos. Because there are stick-type and wheel-type transmitters, use which ever fits your convenience best. Use radio set with reverse function. For more information on the radio con-trol set, refer to its instruction manual. Stick-type ch radio set. Wheel-type ch radio set. Battery for Receiver No.7 6V-600mAh RX RX Ni-Cd Battery Battery Box If already included with the radio, no battery box needs to be pur-chased separately. No.76 6V-000mAh Ni-Cd Battery AA-size Batteries (For Transmitter and Receiver) AA AA AA Suitable servos & receiver Servo Receiver Required for engine starting: Glow Fuel Fuel Pump Plug Heater Plug Wrench No.780 RC RC Model Fuel PRO Spec Fuel (Buggy) No.96 Quick Fill Fuel Bottle No.96 One-touch Plug Heater Set No.80 Locking Jig & Wrench Paint For painting the body, use Kyosho paints for models! No.0 POLYCA COLOR No.760 767 KYOSHO SPRAY COLOR KY OSH O S PR AY CO LO R KY OSH O S PR AY CO LO R
REQUIRED FOR OPERATION () 6 Tools required Phillips driver (L.M.S) Needle Nose Pliers Instant Glue Sharp Hobby Knife Wire Cutters Cement Awl Rubber Cement TOOLS INCLUDED Hex Wrench (.mm, mm,.mm, mm) Box Wrench Cross Wrench No.80 SPECIAL TAPER REAMER No need to pre-drill! Drills neat mm to mm holes directly! No.89 ROUND CUTTER & SANDER For trimming bodies! Cutting along curved lines never was so easy! Set up the radio control system as indicated below. RADIO PREPARATION 6 7 8 9 0 START FINISH 8 6 7 8 9 0 Install batteries. (Transmitter) Extend the antenna. (Transmitter) Connect the charged Ni-Cd battery to the receiver. Extend the antenna. (Receiver) Center the trims. Switch on. (Transmitter) Switch on. (Receiver) Make sure the servos are in command. Switch off. (Receiver) Switch off. (Transmitter) Retract the antenna. (Transmitter) 6 7
BEFORE YOU BEGIN () Read through the manual before you begin, so you will have an overall idea of what to do. Check all parts. If you find any defective or missing parts, contact your local dealer or our Kyosho Distributor. How to read the instruction manual: Front Suspension x 0mm Metal Bushing No., No., No.6 This instruction manual uses several symbols. Please note them during the entire assembly. King Pin 6 6.8mm Pillow Ball (Black) R 7 L 8 Key Number, Part Name, True-to-scale Diagram, Quantity Used All parts except screws are identified by key numbers. For purchasing spare parts, find the key no. of the part needed in the spare part list and refer to the left column to look up the corresponding order no. Symbols used throughout the instruction manual, comprise: Part bags used. mm Drill holes with the specified diameter (here: mm). Must be purchased separately! Apply instant glue (CA glue, super glue). Cut off excess. Pay close attention here! Apply rubber cement. Apply grease. Cut off shaded portion. Tentatively tighten. 90 No.90 Ball bearings are optional! (with optional part no.) x Apply threadlocker (screw cement). Assemble as many times as specified (here: twice). Assemble left and right sides the same way. Ensure smooth non-binding movement while assembling. True-to-scale diagram. Assemble in the specified order.
BEFORE YOU BEGIN () This kit contains screws and hardware in different metric sizes and shapes. Before using them, check the screws on the true-to-scale diagrams on the left side in each assembly step. Some screws are extras. SCREWS OTHER HARDWARE Self-tapping (TP) Washer Nut E-ring mm mm mm Cap TP F/H mm Flat Head (F/H) Set F/H mm Metal Bushing Bearing mm Pillow Ball mm 0mm 6.8mm 6 Self-tapping (TP) screws cut threads into the parts when being tightened. Excessive force may permanently damage parts when tightening TP screws. It is recommended to stop tightening when the part is attached or when some resistance is felt after the threaded portion enters the plastic. Correct Wrong Overtightened. The threads are stripped. MEMO
A A ARRANGEMENT OF PLASTIC PARTS ON RUNNERS () No. Shaded parts are not used. 9 9 7 99 97 6 6 7 70 7 7 No. 6 6 No.7 Shaded parts are not used. D 80 7 9 60 6 C 80 B 80 C B 80 D 7 9 60 6 6
ARRANGEMENT OF PLASTIC PARTS ON RUNNERS () No.6 Shaded parts are not used. 9 6 9 8 8 8 9 6 7 9 9 No.8 Shaded parts are not used. 67 67 67 67 6 70 6 9 66 66 6 6 9 90 7
0 Parts are pre-assembled in step ~ 0. 8 () Gear Differential (For front and rear) x mm 8 x 6mm xmm Set Ball Bearing x 0mm Shim 6 6 6mm O O-ring Flat surface.6 x mm Shaft (Black) 7 () (For center) 6 x x 9 0 0 For front and rear For center Gear Differential x 0mm TP TP F/H.6 x mm Shaft (Black) 6 Diff. Oil x0mm 8 x 6mm Ball Bearing () (For front and rear) 6 6mm O O-ring 7 8 () (For front and rear) () (For center) () (For center) x x x0mm For front and rear For center Rear Gearbox x 0mm TP TP x0mm x mm TP TP F/H 9 x 6mm 0 Thick Thin Shim 6 8 9, 0 8 x 6mm Ball Bearing 8 x 6 x mm Ball Bearing 9, 0 Adjust the backlash with the shims. 7 xmm Assemble in the specified order. Apply grease. x Assemble as many times as specified. 8
Rear Gearbox x mm Set Tighten the set screw to the flat spot. xmm x0mm x 0mm S Joint Cup (S) x mm TP TP xmm Chassis x 0mm TP TP F/H x0mm x0mm 6 Front Gearbox x 0mm TP TP x0mm 8 x 6mm Ball Bearing 60 6 8 x 6 x mm Ball Bearing 8 9 x 6mm 0 Thick Thin Shim Adjust the backlash with the shims. 9, 0 9, 0 7 x0mm Apply threadlocker (screw cement). Assemble in the specified order. Apply grease. 9
7 Front Gearbox x mm Set x 0mm TP TP F/H 8 L Joint Cup (L) 6 Tighten the set screw to the flat spot. xmm 8 x0mm 8 Chassis x 0mm TP TP F/H x0mm x0mm 9 Center Gearbox x0mm 79 78 7mm approx. 7mm x 0mm 78 Brake Caliper 80 8 78 79 Brake Pad (Black) Center Differential 8 79 x0mm 80 x0mm Pay close attention here! Apply rubber type glue. Apply threadlocker (screw cement). 0
0 Center Gearbox 8 () (Long) 86 x mm TP TP F/H 7 () (Short) 9 8 mm O O-ring x 6mm F/H 9 x6mm xmm xmm x6mm START Chassis No., No. x 0mm F/H 76 x mm TP TP 7 8 6.8mm L Ball End (L) 8 6mm approx. 6mm 76 6.8mm Ball 7 x 60mm Rod 6 xmm 6 Torque Rod Ball x0mm Part bags used.
Rear Suspension x mm 8 x 6mm Set No., No. Ball Bearing For right side. x 6mm TP TP 8 x mm Shaft.6 x 6mm Shaft For left side. 0 xmm Top x6mm 8 Bottom mm For adjusting the ground clearance. x6mm 7 No., No. Rear Shock Stay x0mm x 0mm Cap x 0mm x mm TP TP x 0mm x0mm 6 x0mm mm mm Holes for mounting. Holes for mounting. x0mm mm Flanged Nut 7.8mm Flange Ball xmm x0mm xmm x0mm Part bags used. Pay close attention here! Assemble in the specified order. Assemble left and right sides the same way.
Rear Suspension x 7mm Shaft No., No. For right side. 7 x 8 x 0mm Collar E.0 E E-ring (Black) 7 For left side. Rear Suspension No., No. 7.8mm L 9 7.8mm S Ball End (L) Ball End (S).mm approx..mm x 0mm Set 9 x 6 Rear Suspension 6 x mm Pin 8 7.8mm Ball No., No. 8 6 Holes for mounting. 0 x Part bags used. Assemble in the Assemble left and right Assemble as many True-to-scale Pay close attention specified order. sides the same way. times as specified. diagram. here!
x0mm 6 7 Front Shock Stay No., No., No. x0mm x 0mm x mm TP TP x0mm mm x 0mm 7.8mm Flange Ball mm x0mm Holes for mounting. x 0mm mm Cap Flanged Nut xmm x0mm xmm 8 Front Suspension x 0mm Cap 8 x 6mm Ball Bearing No., No., No. 69 Knuckle Collar For right side. R R maked. 69 x0mm 6 For left side. L L maked. 6 67.6 x 6mm Shaft 66 69 68 x0mm For right side. 9 Front Suspension 0 For left side. No., No., No. 7 x 8 x 0mm Collar x 6mm TP TP x mm Set x6mm 7 xmm E.0 E E-ring (Black) 8 x mm Shaft x 7mm Shaft 70 x6mm 8 For adjusting the ground clearance. Top Bottom 0.mm Part bags used. Assemble in the Assemble left and right Apply threadlocker Pay close attention here! specified order. sides the same way. (screw cement).
0 Front Suspension No., No., No. x 0mm Set 6 x mm Pin.mm approx..mm 7 6.8mm Ball End 7 9 x 9 7.8mm S Ball End (S) 6.8mm Ball x 0mm TP TP x 0mm TP TP F/H 6 77 x0mm x0mm x0mm Center Gearbox No., No., No.6 x mm Set 9 x 0mm Set x 0mm TP xmm TP 88 89 90 9 89 xmm x0mm x0mm 87 mm 9 87 7mm Use thick one. Bend the rods if they contact the plate. 88 x Part bags used. Assemble in the Assemble left and right Assemble as many True-to-scale diagram. specified order. sides the same way. times as specified.
Steering x 0mm x mm F/H x 0mm Set 8 6.8mm L Ball End (L) No., No., No. 76 x0mm 8 mm approx. mm x 9 x0mm 8 x0mm mm mm 0 96 9 Front mm 96 6 x 0mm Metal Bushing 0 Tapered Collar mm Nylon Nut 76 6.8mm Ball 9 Note the 96 direction. xmm 9 0 97 xmm Steering x mm TP TP 76 6.8mm Ball x 0mm 6 F/H Torque Rod Ball x mm F/H 0 Tapered Collar No., No., No. x 0mm F/H mm 8 6.8mm L Ball End (L) Nut xmm Short 00 Long xmm Note the types of screws! mm 0 99 Remove these screws and retighten after installing 00. 00 xmm xmm mm 76 7 x0mm 8 mm approx. mm mm 6 x0mm x0mm 6 x Part bags used. Assemble as many times as specified. True-to-scale diagram. Pay close attention here! Ensure smooth non-binding movement while assembling. Tentatively tighten. Apply threadlocker (screw cement).
Roll Bar x mm Set No., No. xmm 98 x 0mm F/H 0 0 xmm x0mm Side Guard No. 7 x8mm x8mm 7 x 8mm 6 x8mm Cut off shaded portion which contact the fuel tank as illustrated. mm 6 Engine x 6mm x 0mm Washer 0 x 0mm Shim x0mm Assembled 0 09 08 07 06 x6mm Part bags used. Assemble left and right sides the same way. Cut off shaded portion. 7
7 Engine No. Insert a sheet of paper before installing. x 8mm x8mm x8mm 8 Muffler No., No. Bend maffler stay. x 0mm mm mm 86 mm Nylon Nut 80 Manifold x mm Set mm Washer x0mm xmm 8 86 8 Muffler Long Short 9 Fuel Tank x mm TP TP x 0mm F/H No., No., No.6 xmm 8 8 xmm No.876 To protect the engine from dirt infiltration, purchase Kyosho's No.876 Fuel Filter. 0mm Cut the Silicone Tube to 0mm Length. 6mm Cut the Silicone Tube to 6mm Length. Note the types of screws! x0mm x0mm Use this hole. Part bags used. Pay close attention here! Cut off excess. 8
0 Radio x 8mm No., No.6 7 x0mm 6 x8mm x8mm x8mm x 0mm x 0mm x 8mm TP TP 7 8 x0mm Switch x8mm Switch 96 mm 9 Radio Antenna Receiver 0 No. 0 Hook Pin Better to fill some sponge between radio box and receiver as well as battery. Battery 0 Radio No. x 0mm F/H x0mm x0mm Part bags used. Must be purchased separately! mm mm Drill holes with the specified diameter. 9
Radio x0mm Steering Servo x0mm x0mm x0mm No., No.6 Throttle Servo x0mm x0mm (TP) 8 ( ) (For transponder.) x 0mm TP TP 8 Note the types of screws! Cords 8 8 x 0mm x 0mm F/H 8 Connect as per radio. x0mm(f/h) x0mm(f/h) Radio No., No.6 0mm 6 xmm Parallel x mm Set 6 Steering Rod Part bags used. Must be purchased separately! Pay close attention here! Cut off shaded portion. 0
Radio No., No.6 xmm Servo Horn Throttle Rod Throttle Rod x8mm 7 8 9 xmm 9 6 98mm 0mm approx. 0mm 0mm approx. 0mm xmm 7mm approx. 7mm 6mm Cut the Silicone Tube to 6mm Length. xmm Parallel 6 9 9 x mm Set x 8mm TP TP 8 Spring 9 mm Stopper 6 Brake Rod 6 7 xmm Adjuster Rod 6 Throttle Linkage Adjustment < > < > < > < Neutral > < High Throttle > < Brake > mm approx. mm mm approx. mm 6 6 6 Brake Adjusting Knobs Upper linkage Rear Brake Lower linkage Front Brake Not to stop at the time of idling. Part bags used. Ensure smooth non-binding movement while assembling. Cut off shaded portion. Tentatively tighten. Must be purchased separately!
T H E 7 Engine No., No.6 x 0mm TP TP Rainy Weather 8 9 After putting the cover on, loosen the screw, fit in the plastic washer and screw in the screw again. 0 Soak inner sponge with oil. 8 9 No.98 Air Cleaner Oil x0mm 7 F I N E S T R A D I O C O N T R O L M O D E L S 6 8 Shock Absorber No.7 80 x 6 x mm Plastic Collar 8 E. E E-ring 8 E. 80 Cover the shaft with cloth before gripping it with pliers..8mm L Ball End (L) 0 "A" ("A"marked) 0 S Shock Shaft (S) E. x No.7 9 Shock Absorber Pull down the piston and slowly pour in oil. Keep the piston pulled down and gradually screw on 6 causing excessive oil to overflow. Ensure that each piston moves up and down smoothly. Oil Piston 69 Then, gently move the piston up and down to get rid of air bubbles. 6 x Part bags used. x Assemble as many times as specified.
0 Shock Absorber No.7 9 60 60.8mm Ball 8 68 7 8 For adjusting the spring tension. 8 Compress the spring and install 9. 8 is available in different widths while 60 running, adjust the quantity of 8 used. x Shock No.7 6 6 < > < Front > Shocks 6 < > < Rear > Shocks 6 6 6 x mm Pin 6 6 mm Shock Spacer Plastic Nut 6 Wheels 7 Slide the tires into these slots in the wheels. 7 x Part bags used. x Assemble left and right Assemble as many sides the same way. times as specified. Ensure smooth, non-binding movement when assembling. Apply instant glue (CA glue, super glue).
Wheels No.8 < > < Front > 7 7 Stopper Bolt 7 < > < Rear > Body Mounts No., No.8 x8mm x8mm < > < Front > 67 6 6.6x6mm x 8mm TP TP.6 x 6mm TP TP x 0mm < > < Rear > 70 x0mm 67 66 x8mm x8mm x 0mm TP TP 6 x0mm.6x6mm Part bags used. Cut off shaded portion. Assemble left and right sides the same way.
Body Shell 6mm mm 6mm Fit to the muffler when cutting out. mm mm mm 6 Painting Before painting, use a neutral detergent to remove any oil residues and dirt. Mask the windows from the inside. Refer to the pictures on the box for the color scheme. Paint the body shell from the inside using Kyosho s spray colors. After painting, remove the protective film from the body shell. No.760 Chrome Silver Mask Windows Chrome Silver Mask Windows Chrome Silver Chrome Silver Part bags used. Cut off shaded portion. mm mm Drill holes with the specified diameter.
7 Body Shell x 8mm mm Washer 8 x8mm mm mm mm mm x8mm mm Nut mm mm 8 Decals Apply the decals to the positions indicated in numerical order. The decal numbers between brackets are only for the opposite side. No. 9 No.6 No. No. 8 0 7 66 67 8 6 7 68 68 8 76 69 6 6 No. No. No.6 7 6 7 6 No.6 No. No. 79 7 6 8 6 7 No. No.6 No. No. 7 0 9 0 7 7 0 68 76 77 78 68 69 70 7 ( ) 6 6 9 9 0 6 No. No. No.6 9 60 6 6 7 80 No. 8 ( 9 ) ( ) 6 ( ) 7 8 6
9 Body Shell 79 Body Pin No. Slightly bend the body pins as shown in the diagram for easier removal. 79 79 79 79 ADJUSTMENT 6 Part bags used. Cut off shaded portion. 7
Toe Adjustment (Front) Toe - in Tie Rod L Toe - out Adjust the front toe either by making the tie rods longer or by making them shorter. L Length (L) Toe - in Shortening. Steering Characteristics Straightline stability becomes better. Steering becomes milder. Straightline stability becomes worse. Toe - out Steering response becomes quicker. Ensure that the length of both the left and right tie rods is the same. Caster Angle (Front) Making longer. Camber Adjustment L Length (L) Making longer. L Positive Camber Upper Rod Front / Rear Front Rear Adjust the front / rear camber either by making the upper rods longer or by making them shorter. Negative Camber Steering Characteristics Positive Camber Steering becomes milder. Rear tire grip becomes worse when entering corners. 6 Shortening Front Enters corners more aggressively. Adjust the Caster Angle by Negative Camber Rear Gives rear tires more grip when entering corners. replacing 6. Ensure that the length of both the left and right upper rods is the same either by unscrewing or by tightening the set screw. 6 6 Steering Characteristics Steering becomes Caster (High) milder. 90 Steering response Caster (Low) becomes quicker. Toe Adjustment (Rear) Ride Height Adjust the front / rear ride height. mm Hex Wrench (mm) Set Toe Adjustment (Rear) Adjust the rear toe by replacing. Steering Characteristics 9 Rear tire slip becomes Toe - in more important. Neutral steering (Standard) Toe - in 9 Gives the rear tires more Toe - in grip when exiting corners. Place the chassis on a level surface and lift the front of the model. When setting down the model again, check if both front wheels touch down at the same time. IFW-6 ing in the set screw. Unscrewing the set screw. 6 Brake IFW-6 Ride height becomes lower. Ride height becomes higher. This is pictur for assembling double disk brake. Center Differential IF- 9 9 No.8 IF- 8 IFW-6
If you use an engine other than the one included This kit requires a. class engine. Engine for.-class cars Option parts for using option engines. Plug Joining Pipe Manifold Only using a type of. class engine, which is made crank shaft and pilot shaft as one part (SG shaft only). Muffler No.9 Muffler Joining Pipe No.9 O.S.RZ,, Manifold (O.S.RZ, Picco, Nova Rossi) No.BSW8 Custom Silencer No.96 O.S.RG/GSR Manifold (O.S.RG/GSR) Exchange Diff Ring Gear and Pinion Gear to the option parts shown here. No.IF No.IF No.IF0 No.IF06 Refer below picturs Linkage is also need to change for your engin. Engine Assemble the following parts with pulling the crankshaft. No.IFW No.IF09 x0mm No.96 No.96996 0 08 No.96996 x0mm 09 mm No.966 x7x0.mm No.IF08 x6mm No.966 x7x0.mm A number and / or type of shim need to be adjusted depending on the type of engine. Pay close attention here! Ensure smooth non-binding movement while assembling. Must be purchased separately! 9
Insert a sheet of paper before installing. No.IF07 Front x0mm x 6mm F/H x0mm x 0mm Flanged Cap x6mm x6mm MEMO Must be purchased separately! 0
OPERATING YOUR MODEL SAFELY In order to avoid accidents and personal injury, be sure to observe the following: Since exhausts and fuel vapors are noxious to health, use fuel only outdoors! Keep hands and objects away from rotating engine parts to avoid personal injury. Because after running the engine, the engine and the muffler are extremely hot, beware of getting burned! For accident prevention, do not run your model under Only use glow fuel for radio control models! Never use the following circumstsnces: gasoline or kerosene which might cause accidents such as fires! In place where many people gather. Near residential districts, schools and hospitals. Because fuel is highly inflammable, never use fuel indoors, near any source of heat, open flames or even Near roads, railroads, air corridors and electric lines. sparks! Do not dispose of an empty fuel can into a fire. It might explode causing serious injury! Also make sure that nobody is using the same frequency as you do at the same time! Be particularly careful not to swallow fuel or to get fuel When the radio batteries are empty. into eyes! Nevertheless, should fuel be swallowed, immediately induce vomiting and call a physician. When the model's control or running behavior is Should fuel get into eyes, thoroughly rinse the eyes strange. and seek medical advice. Always store fuel in a safe place out of children's reach with the cap shut tight! The place for storage should be dark, cool and dry!
GP LANDMAX WD 00 KYOSHO / K I N N L A M F K C B A C E D I F G H D O O J E H G L J M B < > EXPLODED VIEW Note that some parts are not sold as spare parts! IF6 66 IF IF IF IF IF 6 GT0 98 GT0 6 GT00 8 IF7 69 IF7 69 BS6 BS GT 7 GT 7 GT 0 IF6 67 BS BS6 BS7 68 GT00 70 IF 6 BS 0 9 FT 6 GT06 70 GT06 6 W 6 FT 67 GT0 0 GT0 FD6 9 FD6 707 968 0 BS79 96 FT 67 FT 66 98 6 GTZ W 6 W 6 GT06 6 GT0 6 98 W 6 Rear Shoch Rear Shoch Rear Diff IF 9 IF 87 8 8 IF GT0 BS6 BS6 BS6 BS7 0 BS IF7 8 IF7 IF GTZ GT 0 IF 8 98 6 BS GT 7 GT08 7 GT 7 IF7 8 IF7 IF GT0 GT0 9 GT6Z IF GT00 7 GT00 8 GT00 7 IF7 GT7 8 BS 8 70 86 IF 8 IF 7 IF IF 6 IF6 968 0 IF IF 7 IF 6 FD6 8 FD6 9 FD6 7 IF7 FD6 6 IF 89 IF 9 IF7 9 IF Center Diff 88 IF7 6 IF7 6 FD6 9 GT0 0 W 6 Front Shock Front Shock Front Diff W 6 98 IF 8 IF 8 IF 6 BS6 FM8 8 IF 7 IF 79 IF 79 IF 78 IF 78 IF 8 BS7 8 IF 86 IF9 90 IF7 9 IF 8 IF 80 IF 80 IF 78 8 IF 6 IF 8 IF 7 IF7 77 8 IF 60 98 6 98 6 GT08 7 IF GT00 9698 7 GT0 99 GT0 97 IF9 00 IF W0 0 W07 76 IF 8 W07 76 IF 6 IF 8 FD6 8 IF8 9 IF8 9 GT0 9 IF8 96 IF8 9 GT0 9 GTB 7 96 LD70 KC 0 KC 09 GT 07 77 IF6 06 KC 08 IF 9 GTB 7 970 80 IF6 IF8 96 W0 0 W07 76 96 8 IF 6 FD6 6 IF 8 W0 0 IF 90 90 8 IF 7 9 GT0 7 GT6Z GT0 9 8 8 7 6 0 BS 0 9 9698
< EXPLODED VIEW > Gear Differential IF9 Front / Rear IF0 IF9 6 BSW6 8 IF0 BS6 IF0 6 BSW6 IF0 0 IF0 9 IF0 BS07 IF06 8 BS6 IF0 Center IF9 IF0 IF9 6 BSW6 7 IF0 BS6 IF0 6 BSW6 IF0 0 IF0 IF0 9 BS07 IF7 BS6 7 IF0 Shock 6 0 8 7 68 GT07 W 80 80 9
No. BS6 BS7 BS BS BS BS7 BS7 BS79 BS07 BS BSW6 FD6 FT FM9 FM8 GTZ GT GT6Z GT GT GTB GT6 GT7 GT00 Part Names 8x6mm 8x6mm Ball Bearing Rear Wheel Shaft Wheel Stopper Set x.6x6mm.6x6mm Shaft x 0 Shim Set 9 0 x OP O-ring (P) 8 x 0 DX,WD Front Wheel Shaft (DX,WD) 68 x Switch Boots Bevel Shaft Adapter Pipe 96 x 9 x 6 8 x OP6 O-ring (P6) 6 x 0 GP 8 6 7 8 x Linkage Set (for GP cars) 9 x x Body Mount 6 66 67 x Body Pin Joint 79 x 0 8 x Hub Carrier (Narrow) x L=8mm Swingshaft (L=8mm) 0 x Rod Set x Pilot Shaft 07 x 7 x Tire (Rally Pattern) Side Guard 7 7 x 7 x Wheel ( spoke-type) Muffler Lower Suspension Arm No. Quantity x 60 00 0 x 60 8 x x0mm x0mm Set x 7 70 x 7 8 x GT0 Upper Arm Set 9 x 7 x GT0 Shock Stay Set 6 6 97 99 x GT0 Servo Saver Shaft 9 x GT0 GT0 Roll Bar Set Radio Plate 98 x x 0 x GT06 Body Mount Plate 6 6 70 x GT07 Spring 68 x GT08 Wheel Stopper Bolt 7 x IF6 Knuckle Arm 66 67 x IF7 IF Knuckle Arm Collar 69 x T Drive Bevel Gear (T) 8 x IF7 8 x 7 x Linkage Set 9 6 x 9 x IF Rear Torque Rod 6 7 8 x IF9 IF IF.6xmm.6xmm Shaft 6.8mm 6.8mm Ball 7.8mm 7.8mm Ball x x 8 x IF6 IF6 Joint Cup (Sports) x Flywheel (Sports) 06 x IF0 Differential Shaft Set 8 9 0 x IF0 Differential Bevel Set x 0 x SPARE PARTS 70 80 0 00 700 80 0 700 00 00 00 0 600 00 00 0 800 000 600 800 800 800 800 00 00 600 600 600 00 00 800 800 00 000 0 80 00 00 700 00 70 00 FOR JAPANESE MARKET ONLY. No. No. Part Names Quantity IF0 Differential Case x IF0 Center Differential Shaft 7 x IF06 8mmT 8mm Bevel Gear (T) x IF Suspension Shaft Set 7 7 x x IF Bulkhead Set 6 7 x IF Suspension Plate Set 60 x IF Suspension Holder 6 90 9 9 x IF7 Bumper 77 x IF8 Servo Saver Set 9 9 x set 96 x IF9 Plate Set 90 00 x IF Center Differential Housing 8 8 x IF Brake Cam Set 87 88 x 89 x IF Brake Disk 80 x IF Brake Disk Set 78 79 8 x 80 x 00 00 800 00 00 600 0 0 00 00 700 00 60 0 00 9 0 6 7 IF Receiver Box 9 x Set 800 8 9 x 8 x IF7 cc Fuel Tank (cc) x 8 x 800 IF7- Antiribration Rubber 8 x 00 IF Center Shaft (Rear) 86 x 0 IF Swingshaft 7 x 60 IF Front Hub Carrier 6 6 x 70 IF6 MP-7. x Main Chassis (MP-7. Sports) 000 IF7 T Spur Gear (T) x 00 KC Special Clutch Shoe 08 x set 09 0 x 00 LD70 Clutch Bearing x 80 W07 6.8mm mm 6.8mm Hard Ball (w/mm hole) 76 x 0 00 W0 Tapered Washer 0 x 0 0 0 6 7 W S 8 Sports Shock (S) 9 6 6 x 000 60 x 96 6.8mm 6.8mm Ball End 8 x 00 8 E.mm E-ring (.mm) 9 x 0 0 8 Emm E-ring (mm) x 0 0 70 KP/KY Strap 86 x 0 0 707 Color Antenna x 6 00 77 GSR GSR Engine 800 90 HD HD Air Cleaner 6 7 8 9 0 x 800 90 Clutch Spring 09 x 00 98 96 Hub Pin T One-piece Clutch Bell T 6 x x 00 600 968 Snap Pin 0 x 0 00 970 Muffler Stay 80 x 00 98 7.8mm 7.8mm Flanged Ball x 00 9698 8x6xmm x 800 8x6xmm Ball Bearing Some of the parts included are not available as spare parts. Purchase optional parts instead.
OPTIONAL PARTS No. No. Part Names Quantity BSW8 Custom Silencer Use together. 800 00 9 Heat-resistant Muffler Jointing Pipe 000 908 Muffler Jointing Pipe Fluorescent Yellow, Fluorescent Pink x 0 BSW7 M Turbo Big Shock (M) 800 GT Slick Tire 600 GTS Chrome Wheel (-spoke) 800 GT Wheel (-spoke) 800 GT / Front Wheel (-spoke / yellow) 800 GT / Rear Wheel (-spoke / yellow) 800 GTW 68 0 0 Universal Swingshaft Narrow 68 & 0 or 0 & 0 in one piece 800 GTW Special Tie Rod Narrow 600 GTW High Grip Tire Radial-pattern 800 GTW High Grip Tire Rally-pattern 800 GTW0 -Speed Transmisson 9800 IF0 6T Spur Gear (6T) Steel made. 900 IF07 O.S. Engine Mount Spacer When Mounting O.S. Engines 600 IF08 Engine Mount 600 IF09 mmp mm Flywheel (for P) 00 IF8 6T Spur Gear (6T) instead of. 00 W0 Inner Sponge (Low-hight) 00 70 Special Antenna Holder 00 790 Color Silicone Tube 00 79KP Fluorescent Silicone Tube Fluorescent Pink 00 79KY Fluorescent Silicone Tube Fluorescent Yellow 00 876 Fuel Filter 000 98 Air Cleaner Oil 000 9 RZ Manifold (RZ) 000 96 RG Manifold (RG) O.S. RG, GSR For O.S. RG, GSR 000 FOR JAPANESE MARKET ONLY. No. No. Part Names Quantity T, 96 One-piece Clutch Bell T instead of,. 00 96 T One-piece Clutch Bell T 96996 x0mm 966 6T x0mm Ball Bearing One-piece Clutch Bell 6T 600 967 7T One-piece Clutch Bell 7T 968 8T One-piece Clutch Bell 8T 90 Loctite (medium strength) 900 96 One-touch Plug Heat Set 800 96 0cc Quick Fill Fuel Bottle (0cc) 900 96 00cc Quick Fill Fuel Bottle (00cc) 00 9660 00 Silicone Oil (00) 9660 0 Silicone Oil (0) 9660 00 Silicone Oil (00) 9660 0 Silicone Oil (0) 9660 00 Silicone Oil (00) 96606 0 Silicone Oil (0) 96607 00 Silicone Oil (00) 96608 00 Silicone Oil (00) 96609 600 Silicone Oil (600) 9660 800 Silicone Oil (800) 96 967 ~ 9677 9696 ~ 9696 96996 000 Silicone Oil (000) for diffs. Silicone Oil Silicone Oil x0mm x0mm Ball Bearing pcs. for shocks 600 000 BODY SET 96 96 998 WRC Body Set (SUBARU IMPREZA WRC) body, decals 6000 00 06 WRC Body Set (PEUGEOT 06 WRC) body, decals 6000 Body Set (LANCIA STRATOS) body, decals, plastic parts 6000 96-96- WRC Decal Set (SUBARU IMPREZA WRC) decals x 06 WRC Decal Set (PEUGEOT 06 WRC) decals x 000 00 000 6
No. 0 0 0 0 0 06 0 8 9 0 97 x6 6 7 8 9 0 mm Size (mm) Round Head x6 x8 x0 x.6x8.6x0.6x.6x each each x x6 x8 x0.6x6.6x8.6x0.6x each each 7 7 mm.6mm mm mm 0 each 0 each x x6 x8 x0 x each x6 x8 x0 x x each x x6 x8 x0 each x x6 x8 x0 each Flanged Nut 00 x6 x8 x0 x x x x6 x8 each each 6 7 x x0 x.6x.6x.6x6.6x8 each each 7 7 mm mm 0 each 0 each Bind.6x.6x6.6x8.6x x x6 x8 x0 x x x6 x8 x0 x6 x8 x0 x x x x8 x0 x x8 x0 x Flat Head.6x8.6x0.6x.6x x6 x8 x0 x x x6 x8 x0 x8 x0 x x0 x x x6 x8 x0 x x x Cap x8 x0 x x.6x8.6x0.6x.6x x8 x0 x x x x6 x8 x0 x x0 x x0 x0 x x0 x x8 x0 x x0 x QUANTITY 00 00 each each each each each each 00 each each each each each each 0 each 00 each each each each each each each each SCREW NUT etc. No. 0 7 8 9 0 7 60 6 6 6 6 Round Head Self-Tapping.6x6.6x8.6x0.6x x6 x8 x0 x x x x6 x8 x0 x x0 x x6 x8 x0 x8 x0 x x8 x0 mm Size (mm) Bind Self-Tapping.6x6.6x8.6x0.6x x6 x8 x0 x x x x6 x8 x0 x0 x x8 Flat Head Self-Tapping Flanged Cap 00 Set x6 x x x6 x x x x0 x x x8 x x x x6 x0 x0 QUANTITY 00 00 Nylon Nut 00 each each each 77 78 79.6mm mm mm each each each each Flanged Nylon Nut 00 00 80 mm each each each each each each each 00 0 each 00 each each each each each No. 8 86 80 8 8 8 8 8 86 87 90 FOR JAPANESE MARKET ONLY. QUANTITY E. E.0 E. E.0 E.0 E.0 E6.0 E7.0 E0.0 Ø Nut Washer mm.6mm mm mm mm E E-Clips 00 00 0 each 0 each 0 0 each 0 each 0 each 0 each 0 each 0 each 0 each 6 each 6 each 7
R THE FINEST RADIO CONTROL MODELS R THE FINEST RADIO CONTROL MODELS 0-00 TEL.06-9- () 0 00 8 00 60007- PRINTED IN JAPAN