Before beginning assembly, please read these instructions thoroughly! THE FINEST RADIO CONTROL MODELS R INSTRUCTION MANUAL :0 SCALE RADIO CONTROLLED.-.5 ENGINE POWERED TOURING CAR SERIES CHASSIS KIT INDEX REQUIRED FOR OPERATION RADIO PREPARATION BEFORE YOU BEGIN ARRANGEMENT OF PLASTIC PARTS ON RUNNERS ASSEMBLY OPERATING YOUR MODEL SAFELY EXPLODED VIEW SPARE PARTS & OPTIONAL PARTS 3 3 5 6 7 30 3 3 33 3 37 UNDER SAFETY PRECAUTIONS This radio control model is not a toy. First-time builders should seek the advice of experienced modellers before commencing assembly and if they do not fully understand any part of the construction. Assemble this kit only in places out of children's reach! Take care before operating this model. You are responsible for this model's assembly and safe operation! Always keep this instruction manual ready at hand for quick reference, even after completing the assembly. *SPECIFICATIONS ARE SUBJECT TO BE CHANGED WITHOUT NOTICE. No. 358 003 KYOSHO CORPORATION
Before beginning assembly, please read these instructions thoroughly! THE FINEST RADIO CONTROL MODELS No.358B R 7 Rear Suspension No., No.5, No.6 96 x 8mm Set Screw 3 x 5mm Cap Screw mm Flanged Nylon Nut Insert from wider side. 98 97 96 The side with the step is a reverse screw. 98 x 5.5mm 3 x mm Pin 57.8mm Ball Stud 69 9mm Pillow Ball Nut 88 Wheel Shaft (Rear) (Silver) 99 57 x8mm Use the holes on the bottom. 57 88 5mm 8 < > < Left > 3x5mm 89 6x8xmm Aluminium Collar < > < Right > R Marked ÒRÓ 0 3 L Marked ÒLÓ 80 89 8 69 80 6 x mm Ball Bearing 00 8 69 7 mm 8 0 x 5mm Ball Bearing 5mm Hex Wrench (5mm) 8 8 9mm Pillow Ball 8 69.5mm Hex Wrench (.5mm) 97 x 0mm Adjustable Rod.8mm 98 6.8mm Ball End 96 6.8mm Flange Ball
8 Rear Suspension No., No.6 For Right Use the uppermost holes. H 9 Marked ÒHÓ 3 x 5mm Cap Screw 9 0 3 x 0mm F/H Screw 87 87 Swing Shaft (Rear) 0 3 x 59mm Shaft 0 H Marked ÒHÓ 3x5mm For Left Wheels < > < Rear > 30mm 75 9 mm < > < Front > 6mm 7 90 mm Remove when adjust. SPARE PARTS No. Part Names VS033 Swing Shaft (Wide tyres) 87 x VZ08 6 6 63 6 65 66 Wheel Shaft (Wide tyres) GRP /0F30 GRP /0 Touring Sponge Tire F30û (Wheel) Pre-Trued & Glued GRP /0F3 GRP /0 Touring Sponge Tire F3û (Wheel) Pre-Trued & Glued GRP /0F35 GRP /0 Touring Sponge Tire F35û (Wheel) No. Quantity 88 89 x 90 x GRP /0F37 GRP /0 Touring Sponge Tire F37û (Wheel) Pre-Trued & Glued GRP /0F0 GRP /0 Touring Sponge Tire F0û (Wheel) Pre-Trued & Glued GRP /0F GRP /0 Touring Sponge Tire Fû (Wheel) Pre-Trued & Glued *SPECIFICATIONS ARE SUBJECT TO BE CHANGED WITHOUT NOTICE. 003 KYOSHO CORPORATION FOR JAPANESE MARKET ONLY. 600 00 700 300 300 300 300 300 300 No. No. Part Names Quantity GRP /0F5 67 GRP /0 Touring Sponge Tire F5û (Wheel) 300 00 Pre-Trued & Glued GRP /0WR30 63 GRP /0 Touring W Sponge Tire R30û (Wheel) Pre-Trued & Glued 300 63 633 63 635 636 637 GRP /0WR3 GRP /0 Touring W Sponge Tire R3û (Wheel) Pre-Trued & Glued GRP /0WR35 GRP /0 Touring W Sponge Tire R35û (Wheel) 9 x GRP /0WR37 GRP /0 Touring W Sponge Tire R37û (Wheel) Pre-Trued & Glued GRP /0WR0 GRP /0 Touring W Sponge Tire R0û (Wheel) Pre-Trued & Glued GRP /0WR GRP /0 Touring W Sponge Tire Rû (Wheel) Pre-Trued & Glued GRP /0WR5 GRP /0 Touring W Sponge Tire R5û (Wheel) Pre-Trued & Glued 300 300 300 300 300 300 3-003 53 06-9-5 ( ) 0 00 8 00 690307- PRINTED IN JAPAN
R R REQUIRED FOR OPERATION () ch radio control set with servos. This kit requires a channel radio control set with servos. Because there are stick-type and wheeltype transmitters, use which ever fits your convenience best. In case of using reverse switch, refer to instruction manual included in the radio set. Stick-type ch radio set. Wheel-type ch radio set. AA-size Batteries (For Transmitter) AA AA Ni-Cd Battery Only use No.76 6V600mAh RX Ni-Cd Battery. (Do not use other batteries.) Servo Suitable servos & receiver Receiver Engine & Muffler Engine for. class cars Plug This kit requires a. class engine. *Only SG Shaft (Pilot Shaft) with Slide Carburettor engine without pull starter is available. Muffler Muffler and Manifold Joining Pipe No.390 R No. 390 Super Tuned Silencer Set (Side) No.VSW008 5. & No. VSW008 ø5. Muffler & Manifold Set (Rear) 3 Required for engine starting: Glow Fuel Glow Engine Fuel No.60700 RC Tornad fuel Fuel Pump No.96 Quick Fill Fuel Bottle Plug Heater No.695 No.695 DC DC Quick Charger Spark Booster Paint For painting the body, use Kyosho paints for models! No.30 POLYCA COLOR Plug Wrench Starter Battery No.7650 767 KYOSHO SPRAY COLOR No.803 Locking Jig & Wrench No.3977 Multi Starter Box KY OSH O S PR AY CO LO R KY OSH O S PR AY CO LO R 5 Other equipment required. Body Air Filter Tape *KYOSHO Touring Car Body. (00mm width)
REQUIRED FOR OPERATION () 6 Tools required Needle Nose Pliers Screw Cement Rubber Cement Phillips Screwdriver (L.M.S) Awl Wire Cutters Box Wrench TOOLS INCLUDED Pliers Sharp Hobby Knife Hex Wrench Grease Cross Wrench (S) Grease 50 No.8095B 00 mm No.8095B Flywheel Wrench No.965 KYOSHO KYOSHO Special Glue Instant Glue Special Glue No.TSW5 Clutch Spring Adjust Tool KNIFE EDGE REAMER No.6950 ROUND CUTTER & SANDER No.89 No need to pre-drill! Drills neat mm to 5mm holes directly! For trimming bodies! Cutting along curved lines never was so easy! RADIO PREPARATION Set up the radio control system as indicated below. 3 5 6 7 8 9 START 0 3 5 6 7 8 9 0 Install batteries. (Transmitter) Extend the antenna. (Transmitter) Connect the charged Ni-Cd battery to the receiver. Extend the antenna. (Receiver) Center the trims. Switch on. (Transmitter) Switch on. (Receiver) Make sure the servos are in command. Switch off. (Receiver) Switch off. (Transmitter) Retract the antenna. (Transmitter) 5 6 FINISH 8 7 3 3
BEFORE YOU BEGIN Read through the manual before you begin, so you will have an overall idea of what to do. 3 Check all parts. If you find any defective or missing parts, contact your local dealer or our Kyosho Distributor. How to read the instruction manual: Front Suspension 5 x 0mm Metal Bushing No., No.5, No.6 Example 3 5 This instruction manual uses several symbols. Please note them during the entire assembly. 5 King Pin 6 7 6 5.8mm Pillow Ball (Black) Key Number, Part Name, True-to-scale Diagram, Quantity Used All parts except screws are identified by key numbers. For purchasing spare parts, find the key no. of the part needed in the spare part list and refer to the left column to look up the corresponding order no. R 5 8 L 5 Symbols used throughout the instruction manual, comprise: Part bags used. Apply instant glue (CA glue, super glue). Apply rubber cement. Apply threadlocker (screw cement). mm Assemble left and right sides the same way. Drill holes with the specified diameter (here: mm). Cut off shaded portion. Apply grease. x True-to-scale diagram. Must be purchased separately! Pay close attention here! Assemble as many times as specified (here: twice). Ensure smooth non-binding movement while assembling. Tentatively tighten. Assemble in the specified order. This kit contains screws and hardware in different metric sizes and shapes. Before using them, check the screws on the true-to-scale diagrams on the left side in each assembly step. Some screws are extras. SCREWS Screw Self-tapping (TP) Screw OTHER HARDWARE Screw Washer Nut E-ring 6 Cap Screw Flat Head (F/H) Screw TP F/H Screw Set Screw mm F/H Screw mm 3mm 3mm Self-tapping (TP) screws cut threads into the parts when being tightened. Excessive force may permanently damage parts when tightening TP screws. It is recommended to stop tightening when the part is attached or when some resistance is felt after the threaded portion enters the plastic. 3mm Metal Bushing Bearing 5mm 0mm Correct Wrong Overtightened. mm Pillow Ball 5.8mm The threads are stripped.
ARRANGEMENT OF PLASTIC PARTS ON RUNNERS () No.3 No. 5 50 50 5 8 8 5 9 8 7 No.5 6 6 69 69 70 67 68 66 65 63 7 6 78 78 7 73 7 7 75 Shaded Parts are not used. 76 76 77 77 5
ARRANGEMENT OF PLASTIC PARTS ON RUNNERS () No.6 9 93 95 99 98 98 9 0 00 9 9 95 No.7 0 03 05 0 0 09 06 08 07 0 0 7 6 30 8 8 3 3 9 6 3 9 3 8 8 7 5 3 3 Shaded Parts are not used. 6
Gear Differential 8 No., No.9 5 7 x x For Front For Rear 3 0 0 3 9 6 3.6xmm 3 7 0 6 9 8 8 9 6 6 9.6xmm No. Pour Silicon Oil (Hard) for front included in the bag No.. No.9 Pour half of Silicon Oil (Hard) and half of Silicon Oil (Soft) for rear included in the bag No.9. 8 Silicone Oil (Hard) 8 Silicone Oil (Hard) 76 Silicone Oil (Soft) OP5 O-ring P5 9 x 0mm Shim x 7mm Shaft 8 3 x mm Pin 0 5 x mm Shim 8 Differential Joint.6 x mm TP TP F/H Screw 8 Part bags used. x Assemble as many times as specified. 7
Speed Changer x mm Set Screw.6 x 0mm Cap Screw 3 x 6mm F/H Screw 3.6x0mm No., No.3, No.7.6x0mm 9 0 85 3 x 30mm F/H Screw 0 0 5mm Roller.6 x 3 x 5.5mm Collar Speed Spring.6mm.5 Tighten.6mm Cap Screw to Collar till the screw stops, and unscrew.5 rounds, then please set up according to the track condition. 9.6x0mm 7 x 8mm Pin 9 5 x 8mm Ball Bearing 30 8 x mm Ball Bearing 3 3x6mm 3 6 8 9 5 9 3 5 x 0mm Ball Bearing 3x6mm 7 If you do not want to install a Roll Bar, use these parts instead. 8 5 3 3x30mm 30 xmm Firmly tighten the set screws onto the flat spots. Part bags used. Apply threadlocker Apply grease. Assemble in the specified order. (screw cement). 8
3 Brake No.3 3 Brake Shaft 6.5mm Note the direction. Top 3 33 Brake Piston 38 mm Disk Plate Bolt 36 35 38 35 36 37 33 Center Gearbox No., No.3 3x3mm 3 x 3mm Set Screw 8mm 6.6mm.6xmm.6 x mm Screw.6mm Washer 3 x mm Pin.6xmm.6mm 7 3 3 3 5 Center Gearbox No. 3 x 0mm TP TP F/H Screw 39 Part bags used. Apply rubber type glue. Apply threadlocker (screw cement). 9
6 Steering No. 3 0 Steering Pin 7 3 x 6mm Metal Bushing Servo Saver Nut 0 0 9.5mm 5 Servo Saver Spring Front Note the direction. Front 8 5 Top 7 Steering No., No., No.9 mm 3x5mm 0mm 5 53 x x 5 3 x 8mm 55 3 x 7 x 3mm F/H Screw Collar 3 x 5mm 56 5.8mm Set Screw Flange Ball 3mm 57.8mm Nylon Nut Ball Stud 57 55 3x8mm 57 55 53 3 x 30mm Rod.8mm Ball End (Medium) 3mm 3mm 5 5.8mm Ball End 56 Part bags used. Apply threadlocker (screw cement). True-to-scale diagram. Pay close attention here! x Assemble as many times as specified. Ensure smooth, non-binding movement when assembling. 0
8 Steering No., No. 50 50 BRG00 50 5 Note the direction. BRG00 50 6 6 (TP F/H) (F/H) 3 x 0mm F/H Screw 3mm 3 x 0mm TP TP F/H Screw 50 5 x 8 x.5mm Plastic Bushing 8mm 3 x 0mm Screw 3x5mm 3 x 5mm Set Screw 3mm Nut BRG00 Part bags used. Temporarily tighten. Apply threadlocker (screw cement). : No.BRG00 Ball bearings are optional! (with optional part no.)
9 Front Gearbox 3 x mm Pin 9 5 x 8mm Ball Bearing No.5 59 9 60 Adjust the backlash with the shims. 93 3 3 9 58 3 5 x 0mm Ball Bearing 59 x 8mm Ball Bearing 60 9 Adjust the backlash with the shims. 60 x 5 x 0.mm Shim 59 9 x 5 x 0.mm Shim 6 93 5 x 8 x 0.5mm Shim 0 Front Gearbox 3 x 6mm Cap Screw 3 x mm Cap Screw 3 x 0mm Cap Screw 3 x 0mm TP TP Screw 3 x 0mm TP TP F/H Screw No., No.5, No.7 3x0mm 3x6mm 63 3xmm 5 6 3x0mm (TP) 03 x 8mm Set Screw x8mm (TP F/H) mm Part bags used. Apply grease.
Front Suspension No., No.5 7mm 85 68 6 3x3mm 83 79 8 < > < Left > 3 x 3mm Set Screw 70 3xmm 66 57 67 57 L Marked ÒLÓ 3 x mm Screw 8 mm Flanged Nylon Nut 3 x mm Pin 57.8mm Ball Stud < > < Right > 7 6.5mm R Marked ÒRÓ 73 8 3 80 7 69 mm 69 9mm Pillow Ball Nut 69 83 3 x 57mm Shaft 65 8 79 Wheel Shaft.5mm 80 6 x mm Ball Bearing 8 0 x 5mm Ball Bearing 8 69 5mm Hex Wrench (5mm) 8.5mm Hex Wrench (.5mm) 8 9mm Pillow Ball mm Part bags used. Temporarily tighten. Assemble left and right sides the same way. Ensure smooth, non-binding movement when assembling. 3
Front Suspension No., No.5 For Right For Left 86 3 x 0mm TP TP F/H Screw E.5 E E-ring E.5 3 Front Suspension 89 90 No., No.3 3 x 5mm TP TP F/H Screw 89 OP3 O-ring P3 (Black) Securely tighten the screws that were only temporarily installed earlier. 3x5mm 3x5mm Part bags used. Temporarily tighten. Assemble left and right sides the same way.
Front Suspension No., No.5 3 x 5mm Set Screw E.5 E E-ring 87 3 x 37mm Shaft 88 Swing Shaft 89 OP3 O-ring P3 (Black) 3x5mm 3x5mm 89 88 3 88 87 E.5 87 3 89 E.5 7 7 Part bags used. Apply grease. Assemble in the specified order. 5
5 Bumper No., No.7 0 3 x 0mm TP TP Screw 6 0 3 x 0mm F/H Screw 3 7 3mm Nylon Nut 3 3mm 6 9 (F/H) 6 Rear Gearbox 3 x 6mm Cap Screw No., No.6 59 60 9 Adjust the backlash with the shims. 3x5mm 3x5mm 3x6mm 3 x 5mm Cap Screw 3 x mm Pin 9 5 x 8mm Ball Bearing 3 5 x 0mm Ball Bearing 58 3 9 3 93 9 60 Adjust the backlash with the shims. 59 93 9 59 x 8mm Ball Bearing 9 60 x 5 x 0.mm 9 x 5 x 0.mm 93 5 x 8 x 0.5mm Shim Shim Shim Part bags used. Apply grease. 6
7 Rear Suspension No., No.5, No.6 96 x 8mm Set Screw 3 x 5mm Cap Screw mm Flanged Nylon Nut Insert from wider side. 98 97 96 98 x 7mm The side with the step is a reverse screw. 3 x mm Pin 57.8mm Ball Stud 69 9mm Pillow Ball Nut 79 Wheel Shaft 99 57 x8mm Use the holes on the bottom. 57 79 5mm 8 < > < Left > 3x5mm L Marked L 80 6 x mm Ball Bearing < > < Right > R Marked R 0 8 3 80 8 69 8 0 x 5mm Ball Bearing 69 mm 00 7 8 9mm Pillow Ball 96 6.8mm Flange Ball 5mm Hex Wrench (5mm) 8 97 x 0mm Adjustable Rod 8 69.5mm Hex Wrench (.5mm) 98 6.8mm Ball End 3.8mm Part bags used. Temporarily tighten. True-to-scale diagram. Assemble left and right sides the same way. Ensure smooth, non-binding movement when assembling. x Assemble as many times as specified. 7
8 Rear Suspension No., No.6 For Right Use the uppermost holes. H 9 Marked H 3 x 5mm Cap Screw 9 0 3 x 0mm F/H Screw 88 Swing Shaft 0 H Marked H 88 0 3 x 59mm Shaft 3x5mm For Left 9 Rear Shock Stay No., No.7 3 x 0mm TP TP F/H Screw 0 3 x 0mm TP TP Screw (TP) (TP F/H) (TP) 0 Rear Suspension No., No.3 3 x 0mm TP TP F/H Screw 8 90 90 Center Shaft Part bags used. Apply grease. Assemble left and right sides the same way. 8
Rear Stabilizer No., No.6, No.9 3 x 3mm Set Screw 3 x 8mm Flanged Cap Screw 5 5.8mm Ball End x 5 3 The side with the step is a reverse screw. 5mm.8mm Ball End (Short) 3 3 x 5mm Adjustable Rod 3mm 5.8mm Ball Stopper 3x3mm 5 3x8mm Rear Body Mounts No., No.7 3 x 0mm TP TP Screw Part bags used. Ensure smooth, non-binding movement when assembling. x Assemble as many times as specified. True-to-scale diagram. Assemble left and right sides the same way. 9
3 Steering Servo No., No., No.5, No.7 3 x 8mm Screw < SANWA > < FUTABA > < FUTABA / S95 > 3 x 0mm TP TP Screw 77 (mm) 3 x 5mm TP TP Screw 56 5.8mm Flange Ball 06 06 < JR > < KO > 77 (mm) 77 (mm) 06 06 3 (mm) 05 Double-sided Tape 06 Note the direction. Set up according the servo you use. 3 x 0mm TP TP Screw 3x5mm 3x8mm 3x5mm Be sure to use the rubber bushings included with the servos. 3 x 5mm TP TP Screw Steering Servo Servo Horn 56 07 8mm approx. 8mm Neutral position must be at a 0 degree angle as shown in the drawing. 0 Part bags used. Must be purchased separately! 0
Servo Saver No., No.5, No.7 Set up according the servo you use. 3 x 0mm TP TP Screw 3 3x5mm 3 x 5mm TP TP Screw Throttle Control Servo 77 78 3 77 78 3 77 78 3 3~.5mm 77 78 3 Use parts 77, 78 and 3 to achieve the dimensions shown in the drawing. 30 08 76 3 x 0mm 3 x 5mm TP TP Screw TP TP Screw 0 5 Battery No., No.7 Suitable Battery No.76 6V600mAh No.76 6V600mAh RX Ni-cd Battery 3 x 8mm TP 6 TP Screw 3x8mm Double-sided Tape Battery Fix with Glass Tape, etc. Part bags used. Must be purchased separately!
6 Receiver Connect as per radio instruction manual. Receiver No.7 Thread antenna cord through. 36 Switch 63 Use straps to prevent the cords from ever touching the ground. Double-sided Tape 35 Antenna Switch 63 / 7 Radio Plate / Fuel Tank No., No., No.5, No.7 8 Use the screws that were tightened temporarily in Step 8. 3xmm 3xmm (TP) 3mm 3 x 0mm TP TP Screw 3mm Nylon Nut (TP F/H) 86 89 5 89 3 x mm TP TP Screw 3 x 0mm TP TP F/H Screw 89 OP3 O-ring P3 (Black) Part bags used. Must be purchased separately! Ensure smooth, non-binding movement when assembling.
8 Engine No.8 0 7 x mm Washer 0 SG For Side Exhaust, SG shaft (Pilot shaft) type. In case of no space as shown, insert the washer included in the kit. 39 37.5mm 7 6 5 3 3D Place the 3D Weights between the pins of the flywheel. 37 37 37 9 Engine No., No.8 (Cap) (Cap) Engine Assembly 3 x 0mm 3 x mm 3 x 5mm Cap Screw Cap Screw Cap Screw 55 Bell Guide Washer 3 5 x 0 x mm Ball Bearing Position the nipple forward as shown in the drawing. Match the nipple direction for the carburetor linkage to the angle shown in the drawing. 0 0.5mm 53 5 0.5mm 53 5x0.mm 5 5x0.5mm Adjust 53 5x0.mm, 5 5x0.5mm so that this space to be 0.5mm (Refer to the Setting Sheet). 9 3 55 5 53 5 3xmm 3x5mm 3 50 5.8mm 5 Note the direction. Select according to the engine you use. 8 5.0mm Engine 8 8 8 8 Cut off shaded portion if it is needed. Part bags used. Must be purchased separately! Apply threadlocker (screw cement). 3
30 Engine No. Engine Assembly No.VSW009 No.3903 For a rear exhaust engine, use Part No. VSW009. For a side exhaust engine, use Part No. 3903. Tighten the screws with one sheet of paper inserted between both gears. 3 x 8mm Screw 3x8mm 3x8mm 3 Muffler No., No.7, No.8 3x3mm 6 09 56 Air Cleaner 3 x 3mm Set Screw 3 x 0mm TP TP F/H Screw Bend the wire to adjust the muffler. Part bags used. Must be purchased separately!
3 Throttle Linkages No., No.5, No.7 8 60 x0mm 58 mm Servo Horn 5mm approx. 5mm Note the direction. 3x3mm 5mm approx. 5mm 7 mm 6 75 3 x 3mm Set Screw mm Nylon Nut 8 59 7 x0mm 57 5mm Cut off the fuel tube 5mm. x 0mm Screw 60 Throttle Brake Spring 6 mm Stopper Come with radio. 0 0 0mm 33 Fuel Tube No.7 9 57 Cut the fuel tubing to the proper length, as shown in the drawing. Part bags used. Must be purchased separately! Ensure smooth, non-binding movement when assembling. 5
No.9 3 Front Shock.8mm Ball End (Short) 7 A.6mm Shock Collar (A) Nylon Nut 66.6mm 68 7 73 69 75 6 68 7 CC-ring Shock Piston 70 O O-ring.6mm Washer 70 7 7.6mm 67 76 Silicone (Soft) x 35 Front Shock No.9 65 77 For Front (Short) x No.9 36 Rear Shock.8mm Ball End (Medium) 7 A.6mm Shock Collar (A) Nylon Nut 66.6mm 68 7 73 69 75 6 68 7 CC-ring Shock Piston 70 O O-ring.6mm Washer 70 7 7.6mm 67 76 Silicone (Soft) x 37 Rear Shock 65 No.9 78 For Rear (Long) x Part bags used. x Assemble as many times as specified. 6
38 Front Shock No., No.9 3 x mm Set Screw 79 3 x 6 x mm Collar 56 5.8mm Flange Ball 3xmm 56 79 56 79 3xmm Front Shock 39 Rear Shock 3 x mm Set Screw 79 3 x 6 x mm Collar No., No.9 3xmm 56 5.8mm Flange Ball 79 56 56 79 3xmm Rear Shock Part bags used. Apply threadlocker (screw cement). 7
0 Wheels 8 80 Cut off. 80 8 x Fit wheels inside tyres as shown. Twist the tyre onto the wheel. After fitting wheels to tyres, apply instant glue as shown. Wheels < > < Rear > < > < Front > mm mm Remove when adjust. x Assemble as many times as specified. Apply instant glue (CA glue, super glue). Assemble left and right sides the same way. Cut off shaded portion. 8
Body Shell No., No.7 83 x 0mm Screw 83 Body Pin 5 5 83 83 83 x0mm 3 83 3 3 x0mm x0mm x0mm Adjust parts 3 up to body. Safety Precautions Always run your car with the body shell fitted! Avoid changing the running direction too often and too abruptly. Do not run your car on ground: that is overgrown with grass. that is muddy, sandy or rocky. Check all screws, nuts etc. on a regular basis for looseness. MEMO Part bags used. 9
Installing Option Parts No.VSW03 Installing No.VSW03 Front One-Way Shaft. VSW03.6x5mm VS033 VSW05 Use the No.VS033 Swing Shaft with wide tires or No.VSW05 Universal Swing Shaft with a One-Way Diff. (Must be purchased separately.) VZ079 3 VSW03.6x5mm VSW03 60 9 59 59 3 Adjust the backlash with the shims. VZ079 60 9 Adjust the backlash with the shims. 3 No.VSW00 Installing No.VSW00 Carbon Shock Stay (Front). VSW00 3xmm VSW00 3x6xmm 79 VSW00 79 VSW00 3x6xmm Front Shock No.VSW005 Installing No.VSW005 Carbon Shock Stay (Rear). VSW005 VSW005 3x8mm(F/H) VSW005 79 VSW005 3x8mm(F/H) VSW005 0 79 0 Rear Shock Must be purchased separately! Apply threadlocker (screw cement). 30
OPERATING YOUR MODEL SAFELY In order to avoid accidents and personal injury, be sure to observe the following: Since exhausts and fuel vapors are noxious to health, use fuel only outdoors! Keep hands and objects away from rotating engine parts to avoid personal injury. Because after running the engine, the engine and the muffler are extremely hot, beware of getting burned! For accident prevention, do not run your model under Only use glow fuel for radio control models! Never use the following circumstsnces: gasoline or kerosene which might cause accidents such as fires! In place where many people gather. Near residential districts, schools and hospitals. Because fuel is highly inflammable, never use fuel indoors, near any source of heat, open flames or even Near roads, railroads, air corridors and electric lines. sparks! Do not dispose of an empty fuel can into a fire. It might explode causing serious injury! Also make sure that nobody is using the same frequency as you do at the same time! Be particularly careful not to swallow fuel or to get fuel When the radio batteries are empty. into eyes! Nevertheless, should fuel be swallowed, immediately induce vomiting and call a physician. Should fuel get into eyes, thoroughly rinse the eyes and seek medical advice. Always store fuel in a safe place out of children's reach with the cap shut tight! The place for storage should be dark, cool and dry! When the model's control or running behavior is strange. 3
B C A C M A B D F G H I I J K L J E L K E H N G M N D F VZ075 68 6 67 66 70 7 7 7 73 65 UM VZ07-307 77 VZ075 W6006 69 UM VZ073-06 78 VZ075 W0 79 VZ085 5 VZ006 00 6 68 67 66 70 7 7 7 73 65 VS07 3 VS06 0 VS05 93 VS05 9 VZ075 W6006 69 W058 56 FM9 83 FT VZ075 75 VZ007 6 VZ0BK 9 VZ007 7 FM9 83 FT 0 VZ7 86 VS0 83 VS07 3 VZ075 75 W508 89 VS0 90 IF58 38 VS00 7 VZ005 7 VZ08 8 VS0 87 VS00 7 VS00 7 VS09 65 W508 89 VS09 6 VS00 70 VS09 6 VS0 87 VS00 68 VS09 66 UM8 57 VS00 67 W508 89 VZ03 79 BRG0 8 VZ03 88 UM8 57 VZ005 73 905 3 VS00 90-35 8 903 80 90BK 8 VZ03 37 VS0 33 VS00 BRG00 30 VS006 FM359 3 9985 35 36 35 36 905 3 VS0 8 VS0 3 VS0 3 FZ7 8 VS00 69 FZ7 8 VS00 69 BRG006 80 VZ00 7 VS07 VS00 9 BRG008 59 60 VS003 8 VS00 VZ0 0 7 VZ0 0 7 VZ0 BS07 9 6 6 9 VZ0 BS07 6 9 VZ0 BS07 6 9 VZ0 6 9 VZ0 9 6 VZ0 BS07 VZ0 9 6 6 9 VZ0 0 7 7 0 VS00 VZW00-0 5 VS09 6 9663 93 BRG00 3 BRG00 9 905 3 VS08 58 BRG008 59 VZ099 55 BRG00 3 BRG03 5 VZ5-5 VZ6-6 50 BRG00 3 FM353 7 VZ093 5 FM35 VZ095 3 VZ09 VZ09 FMW6 6 VZ09 9 0 UM3 39 VS09 37 70KP 6 VZ087 56 VS06 09 W0 79 W058 56 VS06 03 VS09 63 FM9 83 VS07 5 VS07 3 VS00 VZW00-0 5 VS00 VS00 3 VS003 8 BRG008 59 VS07 3 VZ00 76 708 36 708 35 96 96 VS07 6 VS07 30 VS06 08 VS06 07 700KP 63 96 VS06 06 W058 56 VS06 05 790 57 VS07 5 VS07 3 W508 89 790 57 VS07 8 VS07 9 VS03 59 VS07 5 W508 89 9050 86 VS08 3 VS030 8 OT35 LA3 5 W058 56 OT35 LA3 5 OT35 53 VS06 6 VS07 50 VS05 5 VS07 8 VS07 7 VS05 3 VS07 50 VS07 50 VS07 9 LA 0 UH UM W03 55 LA VS0 VS06 6 UM8 57 VS00 VS00 3 VS003 8 VZ08 85 VS03 39 VS00 6 VS00 VZW00-0 7 905 3 BRG00 9 VS008 5 VS005 0 VS00 8 VS005 9 VS03 85 9 BRG00 3 VS005 0 VZ08 0 VZ08 0 VS05 9 VS05 9 VS05 9 90-35 8 903 80 90BK 8 BRG00 9 VS00 6 VS00 5 VS0 90 VS08 58 905 3 VS00 BRG00 3 9663 93 BRG00 9 905 3 UM8 57 UM SPW5 3 LA3 5 9053 VZ00B 99 UM8 57 VZ03 88 VZ03 79 BRG0 8 VZ00B 98 VZ00B 98 VZ077 97 W05 96 W05 96 VZ006 0 FZ7 8 VZ00 69 VS00 69 VS00 7 BRG006 80 FZ7 8 VS003 8 VS00 9 60 VS00 60 9 BRG008 59 VS00 VZ00 75 VS07 7 790 57 VS03 58 VS03 60 VS07 8 VS07 7 VS03 6 9969 VS00 60 9 FW-05R 003 KYOSHO CORPORATION / EXPLODED VIEW < > Parts indentified only by key numbers are not sold individually! 3 33
No. Part Names VS00 Differential Case VS08 VS09 VS030 VS03 VS03 VS033 VS03 3 SPARE PARTS () No. Quantity 5 x.6xmm TP x 8.6xmm Self-Tapping Flat Head Screw VS00 0T Ring Gear Set (0T) 3 60 9 x VS003 Differential Joint 8 3 x VS00 Center Bulk Set 5 6 7 x 8 x VS005 nd Clutch Shoe 9 0 x.6x0mm.6x0mm Cap Screw x VS006 VS007 VS008 VS009 5T st Spur Gear (5T) x 50T st Spur Gear (50T) instead of. 6T nd Spur Gear (6T) 5 x 5T 5 nd Spur Gear (5T) instead of 5. VS00 Oneway Sleeve 6 7 x VS0 nd Shaft 8 x.6x6mm.6x6mm Screw x.6mm.6mm Washer x VS0 Brake Shaft Set 3 33 3 x 3x3mm 3x3mm Set Screw x VS03 Main Chassis 39 x VS0 Steering Plate x VS05 A Servo Saver Shaft Set A 3 5 x VS06 VS07 B Servo Saver Shaft Set B Servo Saver 6 x 7 8 9 5 5 x 50 x VS08 Bevel Shaft (Small) 3 58 x VS09 VS00 Front Bulk Set 6 6 63 65 66 x 67 68 70 x Front Suspension Arm Set 69 x 8 7 x 6 6 x VS0 VS0 Front Lower Suspention Shaft 83 x Front Upper Suspention Shaft 87 x E E.5 E-ring (E.5) x E E.5 E-ring (E.5) x VS03 VS0 Swing Shaft Center Shaft 88 x 90 x VS05 Rear Bulk Set 9 9 93 x 9 95 x VS06 VS07 03 0 05 06 Shock Stay Set 07 08 09 x 0 x 5 6 30 x Small Parts Set 7 8 9 33 x 3 x 5 3 3 x Radio Plate 3 x 33 Flywheel (ø33) 37 x Engine Mount 8 x Linkage Set 58 59 60 6 x 3x3mm 3x3mm Set Screw x xmm nd Shoe Holder 85 x xmm Set Screw x 88 Swingshaft (Wide tyres) instead of 88. VZ08 Use with VZ08. 39T 3, Ring Gear Set (39T) instead of 3,. 50 00 650 550 50 900 00 00 750 750 50 500 550 3800 300 500 350 350 600 500 600 50 50 600 600 500 50 500 000 00 600 300 50 600 650 FOR JAPANESE MARKET ONLY. No. No. Part Names Quantity 3D ASSY33 37 39 0 3 VS035 3D Clutch Assembly (ø33) 6500 00 5 6 7 55 x 53 5 x x 3 3xmm 3xmm Cap Screw x 3x5mm 3x5mm Cap Screw x VS036 FW05 Decal Set (FW05) decals x VZ00B VZ005 Rear Suspension Arm Set 98 Front Knockle Arm 7 99 x 73 x VZ006 Rear Upright 00 0 x VZ007 Bumper 6 7 x 8 x VZ00 Drive Washer Set 7 76 77 78 x 75 x VZ0 Differential Gear Set 6 7 9 0 x 8 VZ03 Wheel Shaft 3 79 x VZ08 Rear Lower Suspention Shaft 0 x VZ0 BK Urethane Bumper (Black) 9 x VZ03 Brake Disk 37 x 3x.7 Front Spring (3x.7) Black 77 x VZ07-307 VZ073-06 VZ075 VZW00 - VZW00-0 x.6 Rear Spring (x.6) Black V-One V-One Shock 78 x VZ077 0 Upper Rod (0) 97 x VZ08 Front Stabilizer Set 8 85 x VZ085 Rear Stabilizer Bar Set 5 x. Rear Stabilizer Bar (ø.) x.6 Rear Stabilizer Bar (ø.6) x VZ087 VZ09 VZ09 VZ093 Muffler Stay 3D 3D Weight 3D 3D Clutch Bell 3D 3D Spring Catch 56 x 3 x 3 9 x 5 x VZ09 3D 3D Flywheel Nut x VZ095 3D 3D Clutch Disk 3 x VZ099 Bell Guide Washer 55 x 53 x 5 x VZ5-0 VZ5 - VZ5 - VZ6-5 VZ6-6 VZ6-7 0.8M/0T st Gear (0.8M/0T) 0.8M/T st Gear (0.8M/T) 0.8M/T st Gear (0.8M/T) 0.8M/5T nd Gear (0.8M/5T) 0.8M/6T nd Gear (0.8M/6T) 0.8M/7T nd Gear (0.8M/7T) 5 instead of 5. 5 x 5 instead of 5. 50 instead of 50. 50 x 50 instead of 50. VZ7 Front Suspension Plate 86 x O O-ring Shaft Set 7 x Diff. Case Seal 5 x 6 65 66 67 68 69 7 73 7 x 7 x 3 70 x 900 600 500 500 00 00 900 600 300 00 300 00 00 300 00 300 800 300 00 00 300 500 600 50 500 500 500 500 500 500 00 600 350
No. Part Names FM9 Body Pin FM35 Clutch Shoe FM353 Spring Nut FM359 st Housing SPARE PARTS () No. Quantity 83 x 0 x 7 x 50 3x6mm 3 x x 3 3x6mm Flat Head Screw FMW6 H Clutch Spring (H) 6 x FT Body Mount 0 x FZ7 BS07 9mm 9mm Pillow Ball Bevel Shaft 8 x 3 x 6 IF58 Disk Plate Bolt (Short) 38 x LA Steering Pin 0 x LA3 5.8mm 5.8mm Ball End 5 x SPW5 Adjuster Rod Set 3 x ORG05 O P5 O-ring (P5) x 0 OT35 Upper Rod 53 x 5 x 8 UM.8mm.8mm Ball End x 6 UM8.8mmL.8mm Ball Stud (L) 57 x UM3 Tapered Collet 39 0 x BRG00 BRG00 BRG00 BRG006 BRG008 BRG0 BRG03 W0 W03 W05 W058 5x0x Shield Bearing (5x0x) 3 x 5x8x.5 Shield Bearing (5x8x.5) 9 x 8xx Shield Bearing (8xx) 30 x 6xx Shield Bearing (6xx) 80 x x8x Shield Bearing (x8x) 59 x 5x5x Shield Bearing (5x5x) 8 x.8x0x Thrust Bearing (.8x0x) 5 x set mm Aluminium Collar (mm) 79 x 0 3mm Aluminium Collar (3mm) 55 x 6.8mm 6.8mm Hard Flanged Ball 96 x 0 5.8mm 3mm 5.8mm Flanged Hard Ball (w/3mm hole) 56 x W508 O O-ring Set 89 x W505B Shock Cap Set (Blue) 75 x W506 W507 Shock Plastic Parts O O-ring Set 6 7 65 x 7 x 70 x W6006 HC HC Diaphrogm (Black) 69 x 8 50 00 00 300 300 00 300 550 00 50 300 650 00 380 300 00 50 000 000 000 000 800 00 000 50 50 700 00 350 700 50 50 00 No. 700 KP/KY 70 KP/KY 708 790 808 879 Part Names S Fluorescent Strap (S) M Fluorescent Strap (M) Color Antenna (Black Cap) 35 36 x Color Silicone Tube 57 x Rod Stopper Hoby Grease 6 x 5 pcs. FOR JAPANESE MARKET ONLY. No. Quantity 63 x 8 6 x 8 80 00 50 500 00 50 50 90W 90BK 5/ Aero Wheel (5-spoke / white) 8 x 5/ Aero Wheel (5-spoke / black) 8 x 00 00 90 5 8-8W Aero Wheel (5 spoke-type) 8 pcs 8 x 8 000 903 90-35B M Inner Foam M VM-35MN V-Slicks Tire M-35MN 80 x 8 x 00 00 9050 75cc Fuel Tank (75cc Plate) 86 x set 500 9050-0 5 CS 8mm Fuel Tank Sponge Packing 5 pcs. CS-ring (8mm) x 5 300 905 xmm xmm Pin 3 x 0 300 9053 5.8mm 3x3mm 5.8mm Hard Ball Joint x x 3x3mm Set Screw 600 9696 Brake Disk Pad 35 x 300 9985 Hard Brake Lining 36 x 00 96 Double-sided Sponge Tape x Sheet 300 Some of the parts included are not available as spare parts. Purchase optional parts instead. 35
36 OPTIONAL PARTS No. No. Part Names Quantity 7075 39 VSW00 Special Main Chassis 7075 made instead of 39. 7000 00 3 VSW00 Carbon Upper Plate lightweight high strength instead of 3. 500 VSW00 Carbon Shock Stay (Front) lightweight high strength 03 instead of 03. 600 VSW005 Carbon Shock Stay (Rear) lightweight high strength 0 instead of 0. 300 VSW006 & Universal Swing Shaft for Rubber Tire & Differential Gear. 300 VSW007 Universal Swing Shaft (Short) for Wide Sponge Tire (Rear). 300 VSW008 5. & FM05R 5. Muffler & Manifold Set Only for FM05R (Rear) 700 VSW009 FM05R Manifold (Rear) Only for FM05R 3000 VSW00 5. FM05R 5. Muffler Only for FM05R (Right) 5000 VSW0 8 Aluminum Center Strut instead of 8. pcs. 500 VSW03 Front Oneway Shaft instead of Front Differential Unit. 00 VZ079 Need VZ079 VSW0 Carbon Steering Plate lightweight high strength instead of. 00 VSW05 Universal Swing Shaft (For Oneway) In case of using Front Oneway Unit. 300 VZW009 TCD V-One TCD Gear Set (for V-One) 7500 VZW00 Drive Washer Set Aluminum (Hard Type) 300 VZW05 SP SP Brake Disk 700 9986 Use Together with. Soft Brake Lining 00 VZW0V 6/9mm 8 6 Titanium / 9mm Ball Screw Includes pcs. Replacement for 8. 800 VZW0V 6/9mm 8 8-8 6 Titanium / 9mm Ball Screw Includes 8pcs. Replacement for 8. 600 VZ08 VS033 Wheel Shaft (Wide tyres) Use with VS033. 700 VZ086 VZ097 09 Muffler Stay Holder Aluminum instead of 09. 6 Tapered Collet ( 6) For Picco engines. 00 00 APP0 APP 35 36 37 APP Brake Set Replacement for 35 36 37. 3800 BRG007F 3x6x.5mm 3x6x.5mm Ball Bearing instead of. pcs. 000 FM337 9mm& 9mm Ball Screw High Intensity & Quality. 900 FM35 Clutch Spring Soft type 300 FMW0 Clutch Shoe (Gray) Mild for shifting. 00 FMW Clutch Shoe (Red) Sharp for shifting. 700 TSW5 0.05mm Clutch Spring Adjust Tool Scale (0.05mm) 500 TSW6 Aluminum Ride Height Gauge Large Type. 500 W600 30 Titanium Coating Dumper Shaft (30) Nut Type 00 W6007 HC 69 8 HC Diaphrogm (White) instead of 69. Soft type (8 pcs.) 00 776 / 0x0x330mm Pit Box Size / 0x0x330mm 6800 89 Hobby Shears & Sander Making short work of cutting bodys. 000 98 Air Cleaner Oil 000 659 5 Muffler Gasket 5pcs. (Side) 00 390 R Super Tuned Silencer R Set Side 6800 39056 Manifold Spring pcs. 50 39308 M Fuel Filter (M) 000 560 Precision Camber Gauge 00 Team 5803B Team Multi Box (Black) Convenient box in storage. 9800 76 3800 Ni-Cd battery for Receiver 75 7300 6V X-FORCE 600 6V X-FORCE 600 NiCd-Battery Multi Charger BP Glow Fuel 800 000 FOR JAPANESE MARKET ONLY. No. No. Part Names Quantity 730 Super Starter Pack 3600 00 BP R/C 730 BP Fuel Peak Power 3600 Glow fuel for R/C Engine 805 Tire Fitting Tool 00 805 00mm Toe Angle Gauge (00mm) 800 803 Taper Reamer Tool for making holes on Bodies. 800 803 & Locking Jig & Wrench 800 80 5mm Ball-Point Hex Wrench 5mm 850 8765 Maintenance Stand Aluminum Stand for Maintenance. 800 90 Multi Ride Height Gauge 800 9060-5 Muffler Joint Pipe(-5) High Heat Resistant Type. 900 90-5B VM-5MN V-Slicks Tire M-5MN mm Width mm 00 90-30B VM-30MN V-Slicks Tire M-30MN mm Width mm 00 90-0 VM-0MN V-Slicks Tire M-0MN mm Width mm 00 9 -B G# G-Slicks Tire # mm Width mm 00 9-7B G#7 G-Slicks Tire #7 mm Width mm 00 9 G#30 mm -30B G-Slicks Tire #30 Width mm 00 9 G#33 mm -33B G-Slicks Tire #33 Width mm 00 9 G#36 mm -36B G-Slicks Tire #36 Width mm 00 9 Rear Wing Spacer To adjust Rear Height & Angles. 00 93 Fuel Tube.x6x000mm 700 9905 RM-MN - R-Slicks Tire M-MN pcs. 000 9905 RM-MN -P R-Slicks Tire M-MN pcs. 600 9905 RM-30MN -30 R-Slicks Tire M-30MN pcs. 000 9905 RM-30MN -30P R-Slicks Tire M-30MN pcs. 600 90 Loctite (medium strength) Screw Cement. 900 9606 6x8mm 6x8mm Shim Set 50 965 Silicone Seal 800 9653 Screw Rescuer Support to unscrew. 500 965 KYOSHO g KYOSHO Special Glue (g) Instant Glue 700 9655 KYOSHO0ml Kyosho Special Primer (0ml) 000 9605 Power Cleaner 800 96 50cc Quick Fill Fuel Bottle (50cc) For quick charge! 900 96 500cc Quick Fuel Pump 500cc For quick charge! 00 96508 HG HG Joint Grease 800 9665 SP SP Bearing Liquid Retrieves potentiality of Bearing. 000 9698 Molybdenum Coat 600 607005 0EX-Formula Tornade Fuel 0EX-Formula 300 6070 6950 695 695 600 Tornade After Run Oil 6950 00mm Milder steering than Dodge Stratus body shell. 000 Body Set OPEL VECTRA (00mm) body, decals, screws. 69507. 00mm Quicker steering than Opel Vectra body shell. 000 Body Set DODGE STRATUS. (00mm) body, decals, screws. Knife Edge Reamer Spark Booster DC DC Quick Charger (For Spark Booster) 000 800 900
No. No. Part Names Qty. SIL000 00 Silicone Oil (00) 50 SIL050 Silicone Oil (50) 00 SIL000 Silicone Oil (00) 50 SIL050 Silicone Oil (50) 300 SIL0300 Silicone Oil (300) 350 for shocks. SIL0350 Silicone Oil (350) 00 SIL000 Silicone Oil (00) 50 SIL050 Silicone Oil (50) 500 SIL0500 Silicone Oil (500) 550 SIL0550 Silicone Oil (550) OPTIONAL PARTS (3) FOR JAPANESE MARKET ONLY. No. No. Part Names Qty. No. 600 SIL0600 Silicone Oil (600) SIL000 700 SIL0700 Silicone Oil (700) SIL5000 800 SIL0800 Silicone Oil (800) SIL6000 900 SIL0900 Silicone Oil (900) SIL7000 000 for shocks. SIL000 Silicone Oil (000) SIL0000 600 00 600 00 00 SIL00 Silicone Oil (00) SIL0000 00 SIL00 Silicone Oil (00) SIL30000 300 SIL300 Silicone Oil (300) SIL0000 000 SIL000 Silicone Oil (000) SIL50000 SIL3000 3000 Silicone Oil (3000) for diffs. SIL00000 Part Names 000 Silicone Oil (000) 5000 Silicone Oil (5000) 6000 Silicone Oil (6000) 7000 Silicone Oil (7000) 0000 Silicone Oil (0000) 0000 Silicone Oil (0000) 30000 Silicone Oil (30000) 0000 Silicone Oil (0000) 50000 Silicone Oil (50000) 00000 Silicone Oil (00000) No. Qty. for diffs. 600 00 No. 0 0 03 0 05 06 0 3 5 8 9 0 3 68 x 5 6 7 8 9 30 3 x6 x8 x0 x5.6x8.6x0.6x.6x 3 33 x x6 x8 x0.6x6.6x8.6x0.6x 7 7 mm.6mm 3mm mm 0 each 0 each 3x 3x6 3x8 3x0 3 x 3 3x6 3x8 3x0 3x 3x 3x 3x6 3x8 3x0 35 3x5 3x6 3x8 3x0 Flanged Nut 00 x6 x8 x0 x 3x 3x 3x6 3x8 36 37 3x5 3x30 3x35.6x.6x5.6x6.6x8 7 75 3mm mm 0 pcs 0 pcs.6x.6x6.6x8.6x 3x 3x6 3x8 3x0 3x 3x 3x6 3x8 3x0 x6 x8 x0 x 3x 3x5 3x8 3x30 x5 x8 x0 x.6x8.6x0.6x.6x 3x6 3x8 3x0 3x 3x 3x6 3x8 3x0 x8 x0 x5 x0 3x 3x 3x6 3x8 3x30 3x3 3x3 3x35 x8 x0 x x.6x8.6x0.6x.6x 3x8 3x0 3x 3x 3x5 3x6 3x8 3x0 3x5 3x30 3x35 3x0 x0 x5 x0 x5 x8 x30 x35 x0 x5 96.6x8 mm Size (mm) Round Head Screw Bind Screw Flat Head Screw Cap Screw QUANTITY 00 00 00 0 each 00 each each each each each each each each each SCREW NUT etc. No. 0 3 7 8 9 50 53 5 57 60 6 6 63 6 Round Head Self-Tapping Screw.6x6.6x8.6x0.6x 3x6 3x8 3x0 3x 3x 3x5 3x6 3x8 3x0 x5 x0 x5 3x6 3x8 3x0 x8 x0 x x8 x0 Bind Self-Tapping Screw.6x6.6x8.6x0.6x 3x6 3x8 3x0 3x 3x 3x5 3x6 3x8 3x0 x0 x5 x8 5 x8 x mm Size (mm) Flat Head Self-Tapping Screw Flanged Cap Screw 00 Oval Head Screw Set Screw 3x6 3x 3x 3x6 3x3 3x 3x5 3x0 x x5 x8 x 5x 5x5 5x6 5x30 5x0 QUANTITY 00 00 Nylon Nut 00 77 78 79.6mm 3mm mm 5 pcs 5 pcs 5 pcs 8 5mm pcs 83 3mm 5 pcs 00 each each 00 0 each 00 3 each 3 each 3 each 3 each 3 each 65 3x0 3x5 3 each 66 x8 0 each No. 80 85 86 89 380 38 38 383 38 385 386 387 390 FOR JAPANESE MARKET ONLY. QUANTITY mm E.5 E.0 E.5 E3.0 E.0 E5.0 E6.0 E7.0 E0.0 mm Nut Flanged Nylon Nut 00 Washer mm.6mm 3mm mm 5mm.6mm E E-Clips 00 5 pcs 00 0 each 0 each 0 each 50 0 pcs 0 pcs 0 pcs 0 pcs 0 pcs 0 pcs 0 pcs 6 pcs 6 pcs 37
"Kyosho Direct-Mail-Parts-Order-System" is available only for Japanese market. 00 () 0 0 0 7 7 6 8 0 (3),00 00 80,680 () () () 0 0 0 7 7 6 8 0 ()
No.358 The service mentioned below is available only for Japanese market.
R THE FINEST RADIO CONTROL MODELS http://www.kyosho.co.jp/ 0 3-003 53 06-9-5 ( ) 0 00 8 00 690307- PRINTED IN JAPAN