INSTRUCTION MANUAL Before commencing assembly, please read these instructions thoroughly! R THE FINEST RADIO CONTROL MODELS FANTOM 00 :8 Scale Radio Controlled. Engine Powered WD Racing Car INDEX REQUIRED FOR OPERATION RADIO PREPARATION BEFORE YOU BEGIN 5 ARRANGEMENT OF PLASTIC PARTS ON RUNNERS 6 ASSEMBLY OPERATING YOUR MODEL SAFELY EXPLODED VIEW 8 SPARE PARTS & OPTIONAL 30 PARTS SAFETY PRECAUTIONS This radio control model is not a toy. 000 KYOSHO 3 3 7 6 7 First-time builders should seek the advice of experienced modellers before commencing assembly and if they do not fully understand any part of the construction. Assemble this kit only in places out of children's reach! Take care before operating this model. You are responsible for this model's assembly and safe operation! Always keep this instruction manual ready at hand for quick reference, even after completing the assembly. SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE. No. 3999
R R REQUIRED FOR OPERATION () ch radio control set with servos. Stick-type ch radio set. Wheel-type ch radio set. This kit requires a channel radio control set with servos. Because there are stick-type and wheeltype transmitters, use which ever fits your convenience best. Switch the reverse (transmitter) for the throttle control. For more information on the radio con-trol set, refer to its instruction manual. AA-size Batteries (For Transmitter) AA AA Ni-Cd Battery Suitable servos & receiver Servo No.73 Receiver Engine & Muffler Engine for.- class cars This kit requires a. class engine. Plug Muffler Manifold No.955 Joining Pipe Muffler Joining Pipe 3 Required for engine starting: Glow Fuel Glow Engine Fuel Fuel Pump Plug Heater Paint For painting the body, use Kyosho paints for models! No.30 No.60700 RC No.96 No.96 POLYCA COLOR Quick Fill Fuel Bottle One-touch Plug Heater Set Plug Wrench Starter Battery No.7650 767 KYOSHO SPRAY COLOR No.803 Locking Jig & Wrench KY OSH O S PR AY CO LO R KY OSH O S PR AY CO LO R 5 Other equipment required. Body Tire Air Filter No.PC-7007 Tape
6 Tools required REQUIRED FOR OPERATION () Phillips Screw Driver (L.M.S) Needle Nose Pliers Instant Glue Sharp Hobby Knife Wire Cutters Screw Cement Box Wrench Awl Pliers Rubber Cement TOOLS INCLUDED Hex Wrench Grease Grease Cross Wrench (S) No.803 No.89 SPECIAL TAPER REAMER ROUND CUTTER & SANDER No need to pre-drill! Drills neat mm to 5mm holes directly! For trimming bodies! Cutting along curved lines never was so easy! RADIO PREPARATION Set up the radio control system as indicated below. 3 5 6 7 8 9 0 START FINISH 8 Install batteries. (Transmitter) Extend the antenna. (Transmitter) 3 Connect the charged Ni-Cd battery to the receiver. Extend the antenna. (Receiver) 5 Center the trims. 6 Switch on. (Transmitter) 7 Switch on. (Receiver) 8 Make sure the servos are in command. 9 Switch off. (Receiver) 0 Switch off. (Transmitter) Retract the antenna. (Transmitter) 5 6 7 3 3
BEFORE YOU BEGIN () Read through the manual before you begin, so you will have an overall idea of what to do. 3 Check all parts. If you find any defective or missing parts, contact your local dealer or our Kyosho Distributor. How to read the instruction manual: No., No.5, No.6 Front Suspension 5 x 0mm Metal Bushing Example This instruction manual uses several symbols. Please note them during the entire assembly. 5 King Pin 3 5 6 5.8mm Pillow Ball (Black) 6 R 7 L 5 8 Key Number, Part Name, True-to-scale Diagram, Quantity Used All parts except screws are identified by key numbers. For purchasing spare parts, find the key no. of the part needed in the spare part list and refer to the left column to look up the corresponding order no. Symbols used throughout the instruction manual, comprise: Part bags used. Apply instant glue (CA glue, super glue). mm Assemble left and right sides True-to-scale diagram. the same way. Drill holes with the specified Must be purchased separately! diameter (here: mm). Apply rubber cement. Cut off shaded portion. Pay close attention here! Apply threadlocker (screw cement). Ensure smooth non-binding movement while assembling. x Apply grease. Tentatively tighten. Assemble as many times as Assemble in the specified specified (here: twice). order.
BEFORE YOU BEGIN () 5 This kit contains screws and hardware in different metric sizes and shapes. Before using them, check the screws on the true-to-scale diagrams on the left side in each assembly step. Some screws are extras. SCREWS OTHER HARDWARE Screw Self-tapping (TP) Screw Screw Washer Nut E-ring Cap Screw TP F/H Screw mm 3mm 3mm mm Flat Head (F/H) Screw F/H Screw Metal Bushing Bearing 5mm Pillow Ball 3mm mm 0mm 5.8mm 6 Correct Self-tapping (TP) screws cut threads into the parts when being tightened. Excessive force may Wrong permanently damage parts when tightening TP screws. It is recommended to stop tightening when the part is attached or when some resistance is felt after the threaded portion enters the plastic. Overtightened. The threads are stripped. 5
ARRANGEMENT OF PLASTIC PARTS ON RUNNERS Shaded Parts are not used. 3 3 8 39 8 6 9 9 R 3 0 9 9 6 0 9 L 7 3 3 5 8 9 9 7 50 6 5 5 5 55 55 53 5 5 5 55 55 53 37 37 38 3 33 3 36 36 3 35 6A 6B 56 60 6 6 58 6C B 97 A A B 66 5 6 97 6 65 59 57 6 63 K F 70 69
No., No.3, No. Front Suspension < Right > 3 x 8mm F/H Screw 8 65 3mm F/H Washer < Left > 99.8mm Ball Stud x8mm 0 3 3 x 3mm x 8mm x8mm 3x3mm Firmly tighten the 3x3mm set screws onto the flat spots. 3x3mm 3 7 99 3x8mm 65 9 No., No.3, No. Front Suspension 3 x 3mm 37 E3 E E-ring < Right > 6 < Left > 37 37 Put into this space. 3 3x3mm 5 Part bags used. Assemble left and right sides the same way. Tentatively tighten. 7
No., No., No. 3 Front Shaft C C-ring C C-ring 68 xx5mm Ball Bearing 86 8 68 87 56 8 6 x x mm Collar 57 68 8 86 Front Suspension No., No. 87 < Left > < Right > 7 xmm x mm TP TP F/H Screw 6 xmm No.3, No. 5 Front Suspension 86 86 x 8 x 0.5mm 86 Washer 86 < Left > L "L" marked. < Right > R "R" marked. 8 68 xx5mm 8 Ball Bearing 3 x 3mm 68 85 3 x 0mm Pin 68 86 85 Firmly tighten the set screws onto the flat spots. 75 Part bags used. Assemble left and right sides the same way. Apply threadlocker (screw cement). 8
No., No.3, No. 6 Front Suspension < Right > < Left > 03 9 0 03 5mm Hex Wrench (5mm) 99 99.8mm Ball Stud 9 0 03 9mm Ball Screw 0 0mm Screw Cap 7 Front Suspension No., No. < Right > 83 Tighten screws one after the other. 83 Front Swing Shaft Please refer to the Setting Data Sheet about the setting for screws. < Left >.5mm Hex Wrench (.5mm) No., No. 8 Front Stabilizer 3 x 3mm 3 07 Front Stabilizer Cup 3x3mm 06 B Front Stabilizer Shaft 3x3mm 05 A Front Stabilizer Shaft 05 07 06 3x3mm Please refer to the Setting Data Sheet about the setting for Stabilizer. Part bags used. Assemble left and right sides the same way. Ensure smooth non-binding movement while assembling. 9
9 Bumper x 5mm F/H Screw 3 No., No. mm mm mm Nylon Nut 3 50 x5mm x5mm 0 Body Mounts 3 x 0mm TP TP F/H Screw x mm TP Screw No., No. Adjust to body shell. 53 3x0mm 5 Note the direction. 5 Front 55 5 5 xmm No., No.6 Rear Suspension < Right > < Left > 8 x8mm 9 < Right > Note the direction. < Left > 5 3x3mm 99 3 x 3mm 7 x 8mm Firmly tighten the set screws onto the flat spots. 5 99.8mm Rear Lower Suspension Shaft Ball Stud Part bags used. Assemble left and right sides the same way. Tentatively tighten. 0
No.6, No. Rigid Axle C C-ring 66 C C-ring Tighten C-Ring with wrench if it is loose. 68 xx5mm Ball Bearing 9 68 9 3 x 5mm Pin 90 68 No.7, No. 3 Speed Changer x mm.6 x mm Cap Screw 35.6 x 3 x 5.5mm Collar.6xmm 0 5mm Roller 36 6 x x mm Ball Bearing 39 Speed Spring 35 37.6mm 35 39 Tighten.6mm Cap Screw to 35 Collar till the 35 screw stops, and unscrew.5 rounds, then please set up according to the track condition..6xmm 36 0 35 39.6xmm 0 38 37 xmm 89 Firmly tighten the set screws onto the flat spots. No.7, No. Speed Changer 3 x 6mm F/H Screw 3 3 x 0mm Cap Screw 3x6mm 36 3 x mm Washer 3 36 6 x x mm 97 Ball Bearing 3xmm 3x6mm 80 97 3 x 8 x mm Collar 3x0mm 79 Note the direction. Part bags used. Apply rubber type glue. Apply threadlocker (screw cement). Apply grease.
5 ASSY Rear Assembly No., No.6, No. 97 x8mm 5 mm xmm xmm 0mm xmm Firmly tighten the xmm set screws onto the flat spots. 6 98 Push to the end. 67 95 96 96 95 98 3 x 0mm Pin 9 89 x8mm x mm TP TP F/H Screw 85 Note the direction. x mm 9 x 8mm xmm 9 67 6 x 3 x 5mm Ball Bearing 67 ASSY 6 Rear Assembly No. x 8mm F/H Screw x mm TP TP F/H Screw xmm x8mm x8mm xmm Part bags used. Assemble left and right Tentatively tighten. sides the same way. Apply threadlocker True-to-scale diagram. (screw cement).
No.5, No. 7 Rear Suspension < Left > 3 x 3mm 86 86 86 68 L 85 3 x 0mm For Left ("L" marked) Pin 8 68 xx5mm Ball Bearing 85 86 x 8 x 0.5mm Washer < Right > 3 76 8 68 86 Firmly tighten the set screws onto the flat spots. No., No.5, No. 8 Rear Suspension < Right > < Right > < Left > "L marked". 03 9 "R marked". 0 03 9 0 5mm Hex Wrench (5mm) 5 0 9 03 6 < Left >.5mm Hex Wrench (.5mm) Be careful not to screw bent. Please refer to the Setting Data Sheet about the setting. 0 0mm 03 9mm Screw Cap Ball Screw 6 6 No.5, No.6, No. 9 Rear Suspension 3x3mm Tighten screws one after the other. 3 x 3mm 8 Rear Swing Shaft < Left > Please refer to the Setting Data Sheet about the setting. 8.5mm Hex Wrench (.5mm) Part bags used. Assemble left and right sides the same way. Apply threadlocker (screw cement). Ensure smooth non-binding movement while assembling. 3
No., No.6 0 Rear Stabilizer Put bearings on the Stabilizer Bar. Snap on the Stabilizer Bush and then set up the bearings. 69 6 69 5 x 8 x.5mm Ball Bearing 6 08 No., No.6, No. Rear Stabilizer 0.5mm 3mm 09 5.8mm Ball 0 0 5.8mm Ball Stopper 9 3 x 5mm Adjustable Rod 90 5.8mm Ball End 90 The side with the step is a reverse screw. 09 9 90 x mm xmm 3 x 3mm x mm TP TP F/H Screw 3x3mm Rear Stabilizer 7 3x3mm xmm.5mm Hex Wrench (.5mm) x Part bags used. Assemble left and right True-to-scale Assemble as many Tentatively tighten. sides the same way. diagram. times as specified. Cut off shaded portion.
Body Mounts No., No.6, No. 3x0mm 3 x 5mm Screw 33 0 3 x 0mm TP TP F/H Screw 3x5mm 3 Body Mounts No., No.6, No. 3 36 To the inner hole. 3x8mm 3x8mm Note the direction. 9 3 E.5 9 36 E.5 35 3 E.5 E E-ring 3 x 8mm F/H Screw If you use the outer holes for rear body mount, Please shave the shaded portion off. Body Mounts No.6 0 00 L Body Mount Screw (L) 00 0 0 S Body Mount Screw (S) 00 3 00 Part bags used. Ensure smooth non-binding movement while assembling. Apply threadlocker (screw cement). 5
5 Pulley < > 7T < Pulley 7T > < > 6T No.8, No. < Pulley 6T > Small holes should be on Small holes should be on E7 same side. same side. 9 9 59 63 6 30 Use in 6 30. E7 E7 E E-ring 3 58 x 6 6 Middle Block No., No.8 xmm xmm x mm 7T Pulley 7T 67 6 x 3 x 5mm Ball Bearing 67 38 9 xmm Firmly tighten the xmm set screws onto the flat spots. 67 88 6T Pulley 6T 7 Middle Block No. Middle Block x mm TP TP F/H Screw xmm xmm x Part bags used. Assemble as many times as specified. Apply threadlocker (screw cement). 6
8 Center Bulk No., No.8, No. 6 x mm TP F/H Screw x mm 37 37 xmm 37 6 Note the direction. xmm xmm xmm 9 Steering 73 No., No.8, No. FUTABA KO JR SANWA 69 70 F Serrated Cap (F) KJS Serrated Cap (KJS) 56 5.5mm approx. 5.5mm The Side with groove is reverse screw. 3mm x 73 99 99 56 Steering Rod 99.8mm 3mm Ball Stud Nylon Nut 73.8mm Ball End (Medium) Part bags used. True-to-scale diagram. x Assemble as many times as specified. 7
30 Belt x mm No.8, No. xmm Firmly tighten the xmm set screws onto the flat spots. 7T Pulley 7T 88 xmm mm Hex Wrench (mm) 3 Fuel Tank 3 x 6mm F/H Screw No.8, No. 3x6mm 65 8 65 3x6mm 65 3mm F/H Washer 8 8 O P O-ring P 8 80 8 80 8 3x6mm 3 Battery No. KYOSHO 73 6V-600mAh Suitable Battery KYOSHO 73 6V-600mAh Ni-Cd Battery Fix with Glass Tape, etc. Attach Glass Tape around while holding the battery and on flat place. Battery Battery of over 8.5mm width cannot be used. Part bags used. Must be purchased separately! Apply threadlocker (screw cement). 8
No., No.8, No. 33 Steering Servo x8mm.6x8mm 3 Cut the ends off. Steering Servo x8mm 8 x8mm x8mm Do not tighten x8mm too much. JR 3 In the case of JR's servo, Please attach and 3 on contrary sides. x8mm x 8mm 8 O P3.6 x 8mm O-ring P3 Cap Screw 8.6x8mm O O marked Please refer to the Setting Data Sheet about this setting. 3 Belt Tensioner E No., No.8, No. 3x3mm xmm 3 x 3mm 70 x mm 70 6 E E E-ring 39 60 35 Radio Plate No. 3x0mm Belt Tensionner Steering Servo Holes used. Front 3x0mm 3 x 0mm TP TP F/H Screw 8 3x0mm 3x0mm Battery Part bags used. Cut off shaded portion. Must be purchased separately! 9
36 Receiver No., No.8 Come with radio. 0 0 Nylon Strap (Middle) Receiver Switch Attach on the corner. Receiver / No.8, No. 37 Throttle Servo / Radio 3x5mm 3 x 5mm TP TP Screw 6 3x5mm 8 O P3 O-ring P3 8 3x5mm 8 8 8 6A 38 Radio Plate 3 x 0mm TP TP F/H Screw No.8, No. 3x0mm 3x0mm 66 xmm 66 x mm TP TP F/H Screw 66 mm F/H Washe Set up according the servo you use..6 x 0mm Cap Screw 3 x 0mm Cap Screw.6x0mm 3x0mm Set up according the servo you use. Part bags used. Must be purchased separately! 0
3x0mm No.9, No. 39 Engine 3 x 0mm 95 Cap Screw Clutch Spring Guide 93 Tapered Coret 6 Clutch Spring Pilot Shaft.0mm 3 7 7 mm Spring Nut to be 7 screwed.0mm (Refer to the Setting Sheet). 7 Spring Nut 3 Weight Cone 3 9 8 93 3 3 5 95 6 7 0 Engine No.9, No. 3 Thrust Ball Bearing 3 Bell Guide Washer 3 x 5mm Cap Screw 33 5 x 0 x mm 3 x mm Ball Bearing Cap Screw 0.mm 9 99 33 8 0.mm 9 5x0.mm 99 5x0.5mm Adjust 9 and 99 so that this space to be 0.mm (Refer to the Setting Sheet). 30 9 33 3 3 9 99 3xmm 3x5mm Select according to the engine you use. Engine No.9, No. x mm 66 mm F/H Screw F/H Washer 66 xmm xmm 66 66 66 Tighten the screws with one sheet of paper inserted between both gears. Part bags used. Apply grease. Apply threadlocker (screw cement).
マフラー Muffler x 0mm サラビス F/H Screw x mm セットビス No.9, No. スプリング Spring 7 マフラーホルダー Muffler Holder マフラーに合わせて曲げる Bend and adjust to the muffler. xmm ストラップ Strap 7 7 マフラージョイントパイプ Muffler Joint Pipe マフラー Muffler x0mm 3 リンケージ Linkage.6 x 5mm ビス Screw 3 x 3mm セットビス No.8, No. 59 3 6 77.6mm 6B 6C 6 97 3 リンケージ Linkage 3 x 3mm セットビス.6mm(Nylon) 63 3x3mm 燃料チューブを カットして使用 Cut off the fuel tube..6mm 63 6 57 サーボホーン Servo Horn.6x5mm 6B 3x3mm 97 3x3mm 6 mm ストッパー Stopper 63 スロットルブレーキスプリング Throttle Brake Spring.6mm ナイロンナット Nylon Nut.6mm ナット Nut.6mm(Nylon) プロポに付属 Come with radio. No.8, No. 3x3mm 58 使用する袋詰 Part bags used. 別購入品 Must be purchased separately! 可動するように組立てる Ensure smooth non-binding movement while assembling. エアークリーナー Air Cleaner
5 Fuel Tube No.8 77 Fuel Tube No., No.0 6 Front Shock 50 A Shock Collar (A).6mm Nylon Nut.6mm 6 3 8 A 55 73.8mm Ball End (Medium) 9 6 5 C Front Piston C-ring 50.6mm 5 5 Oil 5 9 O.6mm O-ring (Blue) Washer 73 x 7 Front Shock No., No.0 B 5 For Front (Short) x x Part bags used. Assemble as many times as specified. 3
No., No.0 8 Rear Shock 50 A Shock Collar (A).6mm Nylon Nut.6mm 7 3 8 A 55 7.8mm Ball End (Short) 9 7 5 C Rear Piston C-ring 50.6mm 5 5 Oil 5 9 O.6mm O-ring (Blue) Washer 7 x 9 Rear Shock No., No.0 53 For Rear (Long) x No.0 50 Front Shock 0 5.8mm Ball Screw 0 Front Shock x Part bags used. Assemble as many times as specified. Assemble left and right sides the same way.
5 Rear Shock No.0 0 5.8mm Ball Screw 0 Rear Shock 5 Wheels No. 0 x < > < Front > < > < Rear > x After fitting them together, pour instant glue along the seam. x Part bags used. Assemble left and right Apply instant glue Assemble as many times Must be purchased sides the same way. (CA glue, super glue). as specified. separately! 5
53 Wheels < > < Rear > < > < Front > Front Wheel Rear Wheel 5 Body 83 Body Pin No. Rear Wing 83 83 Body 83 Part bags used. Must be purchased separately! 6
OPERATING YOUR MODEL SAFELY In order to avoid accidents and personal injury, be sure to observe the following: Since exhausts and fuel vapors are noxious to health, use fuel only outdoors! Keep hands and objects away from rotating engine parts to avoid personal injury. Because after running the engine, the engine and the muffler are extremely hot, beware of getting burned! For accident prevention, do not run your model under Only use glow fuel for radio control models! Never use the following circumstsnces: gasoline or kerosene which might cause accidents such as fires! In place where many people gather. Near residential districts, schools and hospitals. Because fuel is highly inflammable, never use fuel indoors, near any source of heat, open flames or even Near roads, railroads, air corridors and electric lines. sparks! Do not dispose of an empty fuel can into a fire. It might explode causing serious injury! Also make sure that nobody is using the same frequency as you do at the same time! Be particularly careful not to swallow fuel or to get fuel When the radio batteries are empty. into eyes! Nevertheless, should fuel be swallowed, immediately induce vomiting and call a physician. When the model's control or running behavior is Should fuel get into eyes, thoroughly rinse the eyes strange. and seek medical advice. Always store fuel in a safe place out of children's reach with the cap shut tight! The place for storage should be dark, cool and dry! 7
< EXPLODED VIEW > 一部パーツ販売していないパーツがあります Parts indentified only by key numbers are not sold individually 65 W-06G 65 W-06G 8 7 FM-30 77 36 3 70 FM-37 3 FM-3 8 OT-9 8 80 受信機ホルダー Receiver Holder 9 FM-3 39 FM-3 受信機ホルダー Receiver Holder FM-37 FM-38 67 96888 J FM-37B 5 FM-309 0 FM-338 8 FM-375 FM-39 9 9 FM-3 FM-3 68 9689 66 FM-36 6 FM-3 クラッチ Clutch 0 FM-3 70KP/KY 5 (L) 6 (R) 90 98 FM-309 E 90 95 09 FM-3 77 FM-373 ギヤ Gear 9 SPW-5 J FM-330 9 D 63 FM-36 5 FM-33-RL 99 UM-8 7 (L) FM-305 8 (R) G 37 FM-33 E 88 FM-37 6 FM-36 FM-36 F G ダンパー フロント Shock (Front) I 5 53 FM-35 86 FM-35 FM-36 0 FM-360 FM-336 A 68 9689 K 5 FM-35 5 FM-35 FM-36 86 FM-35 56 57 05 07 06 (L) 3 (R) 65 W-06G 93 FM-33 FM-309 67 96888 FM-300-86 FM-376 75 FM-38 FM-30 03 FM-337 9 FM-3 0 FM-338 85 FM-3 FM-3 0 FM-338 FM-3 FM-367 3 7 5 5 88 FM-378 W-507 9 50 5 プーリー Pulley (7T) 9 50 5 FM-369-.8 5 53 FM-368-.8 FM-3 B W-506 73 76 FM-39 7 UM- 6D FD-65 6 808 FM-307 6 808 63 FM-37 59 FM-37 77 97 FM-37 6 808 0 FM-338 7 FM-30(L) 8 FM-303(R) 9 FM-30(L) 0 FM-303(R) 8 F 68 9689 9 FM-3 99 UM-8 6 9 FM-3 03 FM-337 A FM-365 FM-38 68 9689 86 FM-376 W-507 55 FM-366 03 FM-337 B FM-30(L) FM-303(R) 3 FM-33-FL A (L) (R) 5 FM-30(L) 6 FM-303(R) 3 -RU 85 FM-3 FM-308 50 FM-35 999 KYOSHO / 禁無断転載複製 68 9689 K 68 9689 8 FM-3 FM-339 86 FM-376 W-506 FM-36 36 967 3 (L) (R) リヤ Rear W-505G 8 96 95 FM-33 99 UM-8 FM-33-FU 87 FM-36 87 FM-377 A 96 0 03 FM-337 9 FM-3 0 FM-338 3 8 FM-3 7 FM-35 フロント Front 86 FM-376 8 FM-30 FM-30(L) FM-303(R) FM-360 ダンパー Shock 55 79 FM-36-8L 73 UM- 83 FM-3 C B FM-33 80 FM-363-H 3 FM-359 68 9689 66 W-07G 68 9689 36 967 0 37 39 35 8 FM-3 56 FM-370 FM-333 38 FM-36 8 FM-33 73 UM- D 59 58 5 FM-35 35 39 37 0 9 FM-305 I C FM-330 8 89 FM-38 90 95 H プーリー Pulley (7T) 9 7 9 85 9 95 96 ダンパー リヤ Shock (Rear) 89 FM-379 0 9653 67 96888 38 FM-33 7 37 FM-33 7 FM-353 0 FM-336 FM-30 FM-333 5 FM-35 3 FM-39 95 FM-35 6 FM-35 33 90 03 FM-337 プーリー Pulley (7T) FM-36 33 FM-3 69 70 67 96888 FM-350 9 8 FM-3 99 UM-8 3 FM-39 0 FM-3 6 FM-30 60 FM-37 67 3 96995 93 ギヤ Gear 8 OT-9 9 99 3 H 6 FM-3 58 97 FM-33 00 FM-335 66 W-07G FM-358 69 90 0 FM-335 6A FD-65 8 OT-9 33 90 6 FM-3 6 FM-37 FM-37 30 FM-357-0H 9 FM-356-6L 08 FM-30-.9 35 FM-3 8 FM-3 8 OT-9 クラッチ Clutch 8 FM-355 FM-37 リンケージ Linkage 8 OT-9 FM-380のクラッチASSYもあります FM-36 3 FM-3 8 FM-37 リンケージ Linkage 0 FM-306 6B FD-65 6B FD-65 63 FM-37 57 FM-37 FANTOM 00 9
FM-3 3 33 35 0 x Rear Body Mount 3 9 x E E.5 36 x E-ring (E.5) x FM-33 Center Bulk 37 x 38 x 350 FM-3 FM-35 FM-36 FM-37B FM-38 FM-39 FM-30 FM-3 FM-3 FM-33 FM-3 FM-35 FM-36 FM-37 FM-38 39 0 3 x 9 x0 Small Parts Set 5 6 7 8 x 50 5 x 55 x Front Bumper 5 53 5 x 56 57 60 6 6 63 6 Pulley Set 65 66 x 58 59 x Servo Saver (0) 67 69 70 x 97 x Front One-touch Stopper 75 x Rear One-touch Stopper 76 x Front Wheel Shaft 8 x Rear Wheel Shaft 8 x Front Swingshaft 83 x Rear Swingshaft 8 x 3x0mm 3x0mm Parallel Pin 85 x 0 Front Cup Joint 86 x C Front Shaft 87 x C-ring x Middle Shaft 88 x 89 96 x E E5 Main Saft 0 x E-ring (E5) x 00 600 600 600 00 00 800 800 600 600 00 300 000 FM-39 FM-330 FM-33 C Rigid Axle 90 9 x C-ring x 000 E E-7 9 x E-ring E-7 x Pulley Adapter 50 xmm xmm x xmm Pulley / Brake Adapter 93 x xmm x 000 FM-33 FM-333 Brake Disk 9 x 85 x Brake Pad 95 96 x 600 00 FM-33 Brake Cam 97 58 x 00 FM-335 FM-336 Body Mount Screw 00 0 x 5.8mm 5.8mm Ball Screw 0 x 900 900 SPARE PARTS () FOR JAPANESE MARKET ONLY. No. No. No. Part Names Quantity No. Part Names Quantity FM-300-0 Optional Parts 00 Knuckle Arm FM-337 9mm 00 9mm Ball Screw 03 x 900 FM-300 0mm Knuckle Arm x FM-338-0mm Screw Cap 0 x 00 FM-30 Rear Hub 3 x FM-339 Front Stabilizer Set 05 06 07 x 00 FM-30 FM-30.6 Front Suspension Arm (Left) 5 7 9 x 3 x -.6 Rear Stabilizer Bar (.6) Optional XX x Parts 00 FM-303 FM-30.9 Front Suspension Arm (Right) 6 8 0 x 3 x -.9 Rear Stabilizer Bar (.9) 08 x 00 FM-30 FM-30 3. Rear Upper Arm 5 6 x 50-3. Rear Stabilizer Bar ( 3.) Optional XX x Parts 00 FM-305 FM-306 FM-307 FM-308 FM-309 FM-30 5.8mm Rear Lower Arm 7 8 x 9 x 550 FM-3 5.8mm Ball 09 x 5 Front Wheel 0 x FM-3 One-touch Spring x 0 FM-33 Rear Wheel x 600 x Front Upper Suspention Shaft -FU FM-33 Front Bulkhead 3 x 600 3 Front Lower Suspention Shaft x -FL 98 x FM-33 Rear Bulkhead 5 x Rear Upper Suspention Shaft x -RU FM-33 Rear Bulk Support 6 7 x 350 Rear Lower Suspention Shaft 5 x -RL 00 800 50 50 50 50 FM-3 Fuel Tank 8 x FM-3 Roll Bar 6 x 00 FM-35 Main Chassis 7 x 9800 FM-36 3x0mm xmm 3x0mm Cap Screw,,, xmm F/H Screw, Engine Mount 800 66 x 8 9 x FM-37 Flywheel Set 93 x 800 FM-38 Flywheel Nut x 50 FM-39 Weight Cone 3 x 3 00 FM-350 Clutch Disk x 50 FM-35 Clutch Shoe 5 x 00 FM-35 Clutch Spring 6 x 300 FM-353 Spring Nut 7 x 50 FM-35 Spring Catch 95 x 00 FM-355 Clutch Bell 8 x 00 FM-356-6L 6T st Gear (6T) XX 9 x 700 FM-356 7T -7L st Gear (7T) Optional Parts 700 FM-356 8T -8L st Gear (8T) Optional XX x Parts 700 FM-357-0H 0T nd Gear (0T) XX 30 x 700 FM-357 T -H nd Gear (T) Optional Parts 700 FM-357 T -H nd Gear (T) Optional XX x Parts 700 FM-358 5x0.mm 3 x x 5x0.mm Shim Bell Guide Washer 5x0.5mm x 5x0.5mm Shim 50 FM-359 3x6mm st Housing 3 x 3x6mm F/H Screw x 3 300 FM-360 35 37 39 0 x nd Shoe Set.6xmm.6xmm Cap Screw x 800 FM-36 xmm nd Shoe Holder xmm x FM-36-8L 8T st Spur Gear (8T) XX 79 x 00 FM-36 9T -9L st Spur Gear (9T) Optional Parts 00 FM-363 -H T nd Spur Gear (T) XX 80 x 650 FM-363 5T -5H nd Spur Gear (5T) Optional Parts 650 30 3
SPARE PARTS () FOR JAPANESE MARKET ONLY. No. No. No. Part Names Quantity No. Part Names Quantity FM-36 Shock Adjustable Nut 3 x 350 00 SPW-5 Adjuster Rod Set 9 x 650 00.8mm FM-365 UM-.8mm Ball End 7 73 x 6 300 Shock Case x 800 FM-366.6mm.8mm UM-8.8mm Ball Stud 99 x 00.6mm Nylon Nut Shock Shaft.6mm W-507 Shock Diaphragm 8 x 0 00.6mm Washer x 5 x FM-367 Shock Piston Set 6 7 x W-505G Shock End Cap 55 x 700 FM-368.7 -.7 Front Spring (ø.7) Optional Parts W-506 Shock Plastic Parts x 50 FM-368.8 O -.8 Front Spring (ø.8) XX 5 x W-507 O-ring Set 50 5 x FM-368.9 5.8mm -.9 Front Spring (ø.9) Optional Parts 95 5.8mm Ball End 90 x 8 9 x 50 00 FM-368.0 S -.0 Front Spring (ø.0) XX x 700KP XX x Optional Parts Fluorescent Nylon Strap Pink (S) FM-369.7 S XX x 700KY XX x -.7 Rear Spring (ø.7) Optional Parts Fluorescent Nylon Strap Yellow (S) FM-369.8 M -.8 Rear Spring (ø.8) 53 x 70KP Fluorescent Nylon Strap Pink (M) XX x FM-369.9 M -.9 Rear Spring (ø.9) XX x 70KY XX x Optional Parts Fluorescent Nylon Strap Yellow (M) 80 80 50 50 FM-370 FM-37 L=68 Adjustable Rod (L=68) 56 x 650 705 Antenna Pipe 73 x Linkage Set 57 59 x 63 x 300 808 Rod Stopper 6 x 5 50 FM-37 60 6 x 70 x 5x0xmm 90 700 Tensionner Set 5x0xmm Ball Bearing 69 x 3x3mm, E E 3x3mm, E-ring (E) x 90 5x8x.5mm 7 7 x 5x8x.5mm Ball Bearing 69 x 700 FM-373 Muffler Holder Set xmm, x0mm 50 E E.5 96 Suspension Shaft 9 x x 50 xmm, x0mm F/H Screw x E-ring (E.5) 65 80 x 8 x 5.8mm 3.0mm 9653 800 FM-37 Fuel Tank Post 350 5.8mm Hard Ball Joint (w/3.0mm hole) XX 0 x 3x6mm 3x6mm F/H Screw x 6xxmm 967 000 6xxmm Ball Bearing 36 x FM-375 Radio Plate 8 x 800 5x0xmm 96995 800 0.5 5x0xmm Thrust Bearing 3 x set FM-376 Axle Washer (0.5) 86 x 0 350 5 x8mm x 5 00 3 TP Flat Head Screw xmm x 5 FM-377 Front Belt 3 87 x 800 xmm 68 00 0 xmm Flat Head Screw x 0 FM-378 Middle Belt 0 88 x 700 x8mm 66 XX 00 0 x8mm x 0 FM-379 Rear Belt 0 89 x 900 96.6x8mm.6x8mm XX x 00 5 6 7 8 9 30 3 3 93 95 x C 39 C-ring XX x 0 00 3x x 3x Cap Screw 33 x 6x3x5mm 96888 5x3x5mm Ball Bearing XX 67 x 700 ASSY 3x5 FM-380 Clutch Assembly 8 3x5 Cap Screw x xx5mm 9689 xx5mm Ball Bearing XX 68 x 000 5x0.mm 5x0.mm Shim x 3 x 3 W-06 3mm G 3mm Flat Head Washer(Gold) 65 x 0 5x0.5mm 5x0.5mm Shim x W-07 mm FM-38 G mm Flat Head Washer(Gold) 66 x 0 3 5 6 8 300 F Front Shock Assembly 9 50 5 55 x.6mm x.6mm Nylon Nut.6mm Some of the parts included are not available as spare parts. Purchase x.6mm Washer optional parts instead. FM-38 3 5 7 R Rear Shock Assembly 8 9 50 5 55 x 300.6mm x.6mm Nylon Nut.6mm x.6mm Washer FM-38 Decal Decal x 000 FD-65 Linkage Set 6 x set 00 FM-9 Body Pin 83 x 0 50 OT-9 O P3 O-ring (P3) 8 x 0 00 3
OPTION PARTS FOR JAPANESE MARKET ONLY. No. No. No. Part Names Quantity No. Part Names Quantity W509 Damper Oil Decal 00 9660 600 00 Silicone Oil #800 776 Pit Box 6800 96 Quick Fuel Pump cc 00 89 Hobby Shears &Sander 000 60700 Tornade Fuel.5L 3600 98 560 000 6070 Air Cleaner Oil Tornade After Run Oil 00 600 Precision Camber Gauge TYRE (F) Standard 30 600 00 57507 Team Silicone Fuel Tube(Clear) 00 600 TYRE (F) Standard 35 57507P Team Silicone Fuel Tube(Pink) 00 6003 TYRE (F) Standard 37 57507G Team Silicone Fuel Tube(Green) 00 600 TYRE (F) Standard 0 57507Y Team Silicone Fuel Tube(Yellow) 00 60 TYRE (F) Multi 30 00 00 00 600 5763 Arrows Rear Spoiler 000 60 TYRE (F) Multi 35 600 5730 600 603 TYRE (F) Multi 37 600 5739 000 60 Dust Creaner TYRE (F) Multi 0 600 PC7007 60 TYRE (R) Standard 30 3000 Air Filter 00 60 TYRE (R) Standard 35 3000 80 Ball-Point Hex Wrench 5mm 850 603 TYRE (R) Standard 37 3000 96 9698 One-Touch Plug Heater Set 800 60 TYRE (R) Standard 0 Molybdenum Coat 600 603 TYRE (R) Multi 30 3000 300 603 39308 TYRE (R) Multi 35 Fuel Filter (M) 000 300 5803R 6033 300 9800 TYRE (R) Multi 37 Team Multi Box(Red) 603 300 5803B Team Multi Box 9800 TYRE (R) Multi 0 60 3000 580-5 Hex Wrench.5mm 700 TYRE (F) Standard 30 60 3000 580-0 Hex Wrench mm 700 TYRE (F) Standard 35 603 3000 580-5 Hex Wrench.5mm 700 TYRE (F) Standard 37 60 3000 73 6V-600mAh NiCd-Battery 3800 TYRE (F) Standard 0 605 300 7506 TYRE (F) Multi 30 Multi Charger III 800 605 300 803 Taper Reamer 800 TYRE (F) Multi 35 6053 300 8765 TYRE (F) Multi 37 Maintenance Stand 800 605 300 878 Team KYOSHO Transmitter Bag 800 TYRE (F) Multi 0 606 3800 955 Muffler Joint Pipe 000 TYRE (R) Standard 30 606 3800 965 5.8mm Hard Ball Joint(3.) 800 TYRE (R) Standard 35 6063 3800 TYRE (R) Standard 37 90 Locktite (Medium Strength) 900 606 3800 9605 TYRE (R) Standard 0 800 Power Cleaner 607 00 TYRE (R) Multi 30 9665 SP Bearing Liquid 000 607 00 TYRE (R) Multi 35 966 50 6mm Sim Set 6073 00 TYRE (R) Multi 37 96607 600 Silicone Oil #00 607 00 966 TYRE (R) Multi 0 600 Silicone Oil #50 SP FMW- SP Rear Sus Holder(7mm) 96608 600 Silicone Oil # 3803 3000 Porche 96 Aero (/8) 966 600 Silicone Oil #550 397 VDS 3000 96609 VDS Lola (/8) 600 Silicone Oil #600 60300 3000 Super Porche 96 (/8) 9663 600 Silicone Oil #700 60300L VDS 3000 VDS Lola SP (/8 Light) 3
No. 0 0 03 0 05 06 0 3 5 8 9 0 3 5 6 7 8 9 30 3 mm Size (mm) QUANTITY No. Round Head Screw 00 x6 x8 x0 x5 5 each 3 x x6 x8 x0 5 each 7 mm.6mm 0 each.6x8.6x0.6x.6x 5 each 33.6x6.6x8.6x0.6x5 each 7 3mm mm 0 each 3x 3x6 3x8 3x0 3 x 5 each 3 3x6 3x8 3x0 3x 3x 5 each 3x 3x6 3x8 3x0 5 each 35 3x5 3x6 3x8 3x0 5 each Flanged Nut 00 x6 x8 x0 x 3x 3x 3x6 3x8 5 each 5 each 36 37 3x5 3x30 3x35.6x.6x5.6x6.6x8 5 each 5 each 7 75 3mm mm 0 pcs 0 pcs Bind Screw 00 Bind Self-Tapping Screw 00 Nylon Nut 00.6x.6x6.6x8.6x5 each 3x 3x6 3x8 3x0 3x 5 each 0.6x6.6x8.6x0.6x5 each 3x6 3x8 3x0 3x 3x 5 each 77 78.6mm 3mm 5 pcs 5 pcs 3x5 3x6 3x8 3x0 5 each 79 mm 5 pcs 3 x0 x5 x8 5 each 3x 3x6 3x8 3x0 x6 x8 x0 x 3x 3x5 3x8 3x30 x5 x8 x0 x Flat Head Screw 5 each 5 each 5 each 5 each 00.6x8.6x0.6x.6x 5 each 3x6 3x8 3x0 3x 5 each 3x 3x6 3x8 3x0 5 each x8 x0 x5 x0 5 each 3x 3x 3x6 3x8 5 each 3x30 3x3 3x3 3x35 5 each Cap Screw 00 x8 x0 x x each.6x8.6x0.6x.6x each 3x8 3x0 3x 3x each 3x5 3x6 3x8 3x0 each 3x5 3x30 3x35 3x0 each x0 x5 x0 each x5 x8 x30 each x35 x0 x5 each SCREW NUT etc. 7 8 9 50 53 5 57 60 6 6 63 6 FOR JAPANESE MARKET ONLY. mm Size (mm) QUANTITY No. QUANTITY Round Head Self-Tapping Screw 00 Nut 00 Flat Head Self-Tapping Screw 00 80.6x6.6x8.6x0.6x5 each 3x6 3x8 3x0 3x 3x 5 each 3x5 3x6 3x8 3x0 5 each 85 x5 x0 x5 5 each 86 Flanged Cap Screw 00 3x6 3x8 3x0 x8 x0 x x8 x0 Oval Head Screw 00 3x6 3x 3x 3x6 3x3 3x 3x5 3x0 x x5 x8 x 5x 5x5 5x6 5x30 5x0 each each 0 each 00 3 each 3 each 3 each 3 each 3 each 65 3x0 3x5 3 each 380 38 38 383 38 385 386 387 390 mm E.5 E.0 E.5 E3.0 E.0 E5.0 E6.0 E7.0 E0.0 Flanged Nylon Nut 00 Washer 00 mm.6mm 3mm mm 5mm E E-Clips 5 pcs 0 each 0 each 50 0 pcs 0 pcs 0 pcs 0 pcs 0 pcs 0 pcs 0 pcs 6 pcs 6 pcs 33
R THE FINEST RADIO CONTROL MODELS 3-003 TEL ( 6300006- PRINTED IN JAPAN