Before beginning assembly, please read these instructions thoroughly. R THE FINEST RADIO CONTROL MODELS For Beginner & Intermediate Flyers INSTRUCTION MANUAL Wingspan: 1600mm (6.9") RADIO CONTROLLED.0 CLASS ENGINE POWERED AIRCRAFT INDEX ARF ALMOST-READY-TO-FLY REQUIRED FOR OPERATION / TOOLS REQUIRED / BEFORE YOU BEGIN KIT CONTENTS RADIO PREPARATION ASSEMBLY PARTS LIST OPERATING YOUR MODEL SAFELY ~1 1 1 / 16 UNDER SAFETY PRECAUTIONS This radio control model is not a toy! First-time builders should seek the advice of experienced modellers before beginning assembly and if they do not fully understand any part of the construction. Assemble this kit only in places out of childrenõs reach! Take enough safety precautions prior to operating this model. You are responsible for this modelõs assembly and safe operation! Always keep this instruction manual ready at hand for quick reference, even after completing the assembly. *SPECIFICATIONS ARE SUBJECT TO BE CHANGED WITHOUT NOTICE. 00 KYOSHO CORPORATION No.1111
REQUIRED FOR OPERATION (Purchase separately!) CAUTION: For details concerning the equipment listed below (size, maker, etc.), check with your hobby shop. 1 A Channel radio with standard servos is required. CAUTION: Only use a minimum channel radio for airplanes! (No other radio may be used!) A minimum channel transmitter, configured for aircraft. 1 1 AA-size Batteries AA AA AA 1 Aileron servo extension lead (Propeller included in W/Engine set). Propeller Propeller Purchase a propeller that will match your engine. Required for engine starting: Spinner Sponge Sheet WARNING: Normal gasoline cannot be used with glow engines. Glow engine fuel only. Fuel Pump Plug Wrench Ensure you read and understand the instructions included with your radio. Engine and Muffler Model Aircraft Engine 0 -Stroke.0 Servo ~1mm Glow Plug Muffler 16~0mm (Engine, Muffler and Glow Plug are included in the W/Engine set). MODEL ENGINE FUEL Plug Heater No. 0701 No. 070 No.6951 DC DC Quick Charger No.6951 Spark Booster TOOLS REQUIRED (Purchase separately!) Sharp Hobby Knife Wire Cutters Philips Screwdriver ( L, M, S ) Needle Nose Pliers Scissors Awl 1 Read through the manual before you begin, so you will have an overall idea of what to do. Symbols used throughout this instruction manual, comprise: Cut off shaded portion. Must be purchased separately! Pay close attention here! 1.5mm x Assemble as many times as specified. BEFORE YOU BEGIN 1.5mm Drill holes with the specified diameter (here: 1.5mm). Assemble in the specified order. Check all parts. If you find any defective or missing parts, contact your local dealer or our Kyosho Distributor. Ensure smooth non-binding movement while assembling. Read carefully at this symbol! Included with "GP" version. The pre-covered film may become wrin-kly due to variations of temperature. Smooth out as explained right. with cover (cloth) low setting Use an iron covered with a cloth! Start at low setting. Increase the set-- ting if necessary. If it is too high, you may damage the film.
KIT CONTENTS Decal Stopper 11 Nose Gear Horn 1 Nose Gear 9 Tire 1 Tire Shaft 9 Tire 10 Main Gear 1 Main Wing (R) Main Wing (L) Wing Joiner 9 Tire Stopper Tail Wing 1 1 Aileron Rod 15 Rod Adjuster ( set) Throttlr Rod Shrink Tube Hex Wrench 16 Nose Gear Rod 17 1 Rudder Rod Elevator Rod 19 Linkage Stopper ( 6 pcs) x mm Set Screw ( 6 pcs) Washer ( 6 pcs) 0 E1.5 E E-ring ( 6 pcs) 5 6 Engine Mount 7 Fuel Tank Fuselage Screw / Nut
RADIO PREPARATION 1 A new Ni-Cd battery must charged before use. Refer to the charger instruction manual for directions. Set up the radio as explained below. Servo Receiver Install the grommets to the servo as shown. 1 11 5 7 9 Battery 1 5 Transmitter 6 7 9 6 10 ON OFF 10 11 START 1 5 6 7 FINISH 9 10 11 Install AA-size batteries. (Transmitter) Extend the antenna. (Transmitter) Connect the Ni-Cd battery. Extend the antenna. (Receiver) Center the trims. Switch on. (Transmitter) Switch on. (Receiver) Make sure the servos are in command. Switch off. (Receiver) Switch off. (Transmitter) Retract the antenna. (Transmitter) ASSEMBLY 1 Main Wing 1 Only cut the film. Do not cut into the wood. Main Wing 1 Securely glue together. If it comes off during flights, you may lose control of your airplane, resulting in an accident! Align transparent decals leaving no gap & apply to left & right main wings. 1 Cut off shaded portion. Read carefully at this symbol!
Aileron Servo Supplied with the servo. Supplied with the servo. Aileron Servo 1.5mm 1.5mm Aileron Rod x mm Set Screw x 1 1 19 Linkage Stopper 0 E1.5 E E-ring mm Washer mm approx. mm Aileron Rod Supplied with the servo. mm mm 11~1mm approx. 11~1mm 19 19 mm mm 10mm 10mm Apply heat to shrink the tube. mm 1.5mm mm Beware of the flame! 1 1 Must be purchased Cut off shaded portion. separately! x Assemble as many times as specified. 1.5mm 1.5mm Drill holes with the specified diameter. Ensure smooth non-binding movement while assembling. Pay close attention here! 5
5 Nose Landing Gear x mm Screw 1 16 mm Stopper 1 1 xmm xmm 11 xmm xmm Only cut the film. 6 Engine 0mm x 0mm Cap Screw 10mm 15 Throttle Rod mm Washer x0mm To Muffler mm Nut 1 To Carburetor Engine Relieve this area as needed to allow needle valve clearance. mm mm 5 mm For slightly wider engines, spread slightly wider. mm Pay close attention here! Must be purchased separately! Assemble in the specified order. Cut off shaded portion. Ensure smooth non-binding movement while assembling. Included with "GP" version. 6
7 Main Landing Gear x 16mm Screw x16mm 10 Only cut the film. Do not cut into the wood. Horizontal Tail Only cut the film. Do not cut into the wood. 9 Horizontal Tail.5mm.x5mm.5mm Securely glue together. If it comes off during flights, you may lose control of your airplane, resulting in an accident! Only cut the film. Do not cut into the wood. A = AÕ B = BÕ A AÕ. x 5mm TP TP F/H Screw B BÕ Pay close attention here! Cut off shaded portion..5mm.5mm Drill holes with the specified diameter. Read carefully at this symbol! 7
10 Servo Elevator Control Servo Supplied with the radio. Supplied with the radio. Rear Rudder Control Servo x Front Throttle Servo 11 Rudder Rod mm approx. mm 17 1 Rudder Rod 10mm Apply heat to shrink the tube. Beware of the flame! 1 Use this hole. 1 Elevator Rod 1 Elevator Rod 10mm Apply heat to shrink the tube. 1 mm approx. mm Beware of the flame! 1 Use this hole. Must be purchased separately! x Assemble as many times as specified. Pay close attention here! Read carefully at this symbol!
1 Linkage 19 19 1mm approx. 1mm 19 Linkage Stopper mm 19 1.5mm mm x 1mm approx. 1mm mm 10mm mm approx. 10mm 1.5mm Supplied with the servo. mm mm 0 E1.5 E E-ring mm Washer Supplied with the servo. Supplied with the servo. 1 Linkage xmm x mm Set Screw Throttle Rod xmm Elevator Rod Rudder Rod Steering Rod mm Must be purchased separately! Cut off shaded portion. Assemble as many times Drill holes with the specified mm as specified. diameter. x Ensure smooth non-binding movement while assembling. 9
15 Battery Receiver Connect as per radio instruction manual. Foam Pad Secure foam padding with rubber bands or tape as required. Battery Antenna Tape. Receiver Switch Battery Securely glue together. If it comes off during flights, you may lose control of your airplane, resulting in an accident! Included with the switch. Included with the switch. 16 Folding Propeller Securely tighten the nut holding the propeller for it not come off when the motor is spinning. If com-ing off, there is a high risk of injury! Spinner Muffler Propeller Spinner Must be purchased separately! Pay close attention here! Included with "GP" version. Read carefully at this symbol! 10
17 Main Wing x5mm x 5mm Cap Screw mm mm Washer Securely glue together. If it comes off during flights, you may lose control of your airplane, resulting in an accident! Connect the aileron servo. Connect as per radio instruction manual. 1 Decals Apply included decals. For the correct placement of decals, please refer to box top. Cut off this line. mm 106mm Pay close attention here! Read carefully at this symbol! 11
19 Adjustment Adjust the travel of each control surface to the values in the diagrams. < > < > < Aileron > < Elevator > < > < Rudder > Angle Angle Position for left diagram. 7mm Angle Position for left diagram. 9mm Position for left diagram. 7mm 9mm 15mm 15mm 0 C of G position In order to obtain the CG specified, reposition the receiver and other equipment. 5~90mm CG Do not fly before confirming the correct location of the CG. If the CG is incorrect, you lose control of your airplane which leads to accidents! 1 Engine Preparation Fuel comes out of this pipe when fuel supply is full. Plug Remove pipe attached to carburettor, and add fuel here. Pay close attention here! Must be purchased separately! Included with "GP" version. Read carefully at this symbol! 1
0 6 First-time fliers should seek advice for hints in pre-flight adjustments and assembly from experienced fliers. Be reminded that flying a badly assembled or badly adjusted airplane is very dangerous! In the beginning, first-time fliers should always be assisted by an experienced flier and never fly alone! This model airplane is designed to be powered by a -cycle.0 engine. Installing a more powerful engine than specified or flying the trainer aggressively may lead to serious damages and accidents! As this airplane is intended to be a model for first-time fliers, aerobatic flying cannot be performed! Read carefully at this symbol! No. Part Names 1111-01 Nose Gear Set 1111-0 Main Gear Set 1111-0 Decal No. Quantity 11 1 x 1 10 x 1 x 1 1 x SPARE PARTS 1500 00 000 1600 FOR JAPANESE MARKET ONLY. No. No. Part Names Quantity 1111-0 9 x Sponge Tire Set 100 00 7 901-C Fuel Tank Set (0cc) 900 7 x 1 Set OPTIONAL PARTS Propeller No.901-06 D1 x P6 Nylon Propeller 750 No.9069 No.9096 PP P.P. Pipe Main Wing Taping Tape 00 00 No.1790 Color Silicone Tube 00 Spinner No.900-5 No.901-5 No.90-5 No.906-5 5mm Spinner (White) 5mm Spinner (Red) 5mm Spinner (Yellow) Duralumin Spinner 1000 1000 1000 000 No.90 Fuel Filter (M) 1000 1
"Kyosho Direct-Mail-Parts-Order-System" is available only for Japanese market. 00 (1) 0 0 1 0 7 7 1 1 6 0 () 1,00 00 0 1,60 () () (1) 0 0 1 0 7 7 1 1 6 0 ()
No.1111 The service mentioned below is available only for Japanese market.