Before beginning assembly, please read these instructions thoroughly. R THE FINEST RADIO CONTROL MODELS INSTRUCTION MANUAL INFERNO MP-7. SPORTS INDEX REQUIRED FOR OPERATION RADIO PREPARATION BEFORE YOU BEGIN ARRANGEMENT OF PLASTIC PARTS ON RUNNERS ASSEMBLY ADJUSTMENT OPERATING YOUR MODEL SAFELY EXPLODED VIEW SPARE PARTS & OPTIONAL PARTS 6 7 8 6 7 7 UNDER SAFETY PRECAUTIONS This radio control model is not a toy! First-time builders should seek the advice of experienced modellers before beginning assembly and if they do not fully understand any part of the construction. Assemble this kit only in places out of children's reach! Take care before operating this model. You are responsible for this model's assembly and safe operation! Always keep this instruction manual ready at hand for quick reference, even after completing the assembly. *SPECIFICATIONS ARE SUBJECT TO BE CHANGED WITHOUT NOTICE. 00 KYOSHO CORPORATION No. 9
R REQUIRED FOR OPERATION () Minimum channel radio with servos, and battery box. CAUTION: Only use a surface radio with channels and servos! Stick-type ch radio. Because there are stick-type and wheel-type transmitters, use which ever fits your convenience best. In case of using reverse switch, refer to instruction manual included in the radio set. Wheel-type ch radio. Battery Box If already included with the radio, no battery box needs to be pur-chased separately. AA-size Batteries Servo AA AA AA Suitable servos & receiver Receiver Required for engine starting: Engines for R/C models require glow fuel. Be careful not to purchase gasoline or kerosene by mistake; both cannot be used! Also, be very careful when han-- dling glow fuel which is hi-ghly inflamma-- ble and high-explosive! Besides glow fuel, engines also require engine starting equipment. This comprises a glow plug heater. Glow engine fuel only. R/C Model Fuel No.70 R/C Model Fuel Fuel Bottle Plug Heater No.96 Quick Fill Fuel Bottle WARNING: Gasoline or kerosene cannot be used. No.69 Spark Booster Plug Wrench No.69 DC DC Quick Charger No.80 Locking Jig & Wrench Paint and Brush For painting the body, use Kyosho paints for models! PAINT BRUSH No.0 POLYCA COLOR No.760767 KYOSHO SPRAY COLOR CAUTION: Before using spray colors, always read their explanations! FUELPROFF PAINT KY OSH O S PR AY CO LO R No.8 (mm x m) 8 (.mm x m) 8 (.mm x m) 89 (0.mm x 8m) 860 (0.7mm x 8m) Micron Line Tape KYOSHO No.9670 D- D FLEX COLOR DECAL No.97 MASKING SHEET MICRON LINE TAPE Super-flexible tape for masking and detail designing jobs. Self-adhesive super-flexible sheets that bond to polycarbonate - even when applied to curved surfaces. For safe masking jobs, use this plastic masking sheet featuring one self-adhesive edge.
REQUIRED FOR OPERATION () Tools required TOOLS INCLUDED Hex Wrench (.mm, mm,.mm, mm) Needle Nose Pliers Phillips Screwdriver (L.M.S) CAUTION: Handle tools carefully! Awl Wire Cutters Rubber Cement Screw Cement RUBBER CEMENT LOCTITE Cross Wrench Sharp Hobby Knife KYOSHO Special Glue Instant Glue No.96 Special Glue Cross Wheel Wrench No.89 ROUND CUTTER & SANDER For trimming bodies. Cutting along curved lines never was so easy! RADIO PREPARATION Set up the radio control system as indicated below. KNIFE EDGE REAMER No.690 No need to pre-drill! Drills neat mm to mm holes directly! 6 9 6 9 7 ON OFF Transmitter 8 ON 0 OFF Switch 7 ON OFF 6 7 8 9 0 Servo START 6 7 8 9 0 Insert AA-size dry batteries. (Transmitter) Extend the antenna. (Transmitter) Insert AA-size dry batteries. (Battery Box) Connect the battery box. Extend the antenna. (Receiver) Center the trims. Switch on the transmitter. Switch on the receiver. Make sure the servos move according to your transmitter inputs. FINISH Receiver Switch off the receiver. Switch off the transmitter. Retract the antenna. (Transmitter)
BEFORE YOU BEGIN () Read through the manual before you begin, so you will have an overall idea of what to do. Check all parts. If you find any defective or missing parts, contact your local dealer or our Kyosho Distributor. How to read the instruction manual: Front Suspension x 0mm Metal Bushing No., No., No.6 This instruction manual uses several symbols. Please note them during the entire assembly. King Pin 6 6.8mm Pillow Ball (Black) R 7 L 8 Key Number, Part Name, True-to-scale Diagram, Quantity Used All parts except screws are identified by key numbers. For purchasing spare parts, find the key no. of the part needed in the spare part list and refer to the left column to look up the corresponding order no. Symbols used throughout the instruction manual, comprise: Part bags used. mm Drill holes with the specified diameter (here: mm). Must be purchased separately! Apply epoxy glue. Cut off excess. Pay close attention here! Apply instant glue (CA glue, super glue). Cut off shaded portion. Apply rubber cement. Temporarily tighten. Apply grease. Ensure smooth non-binding movement while assembling. Apply threadlocker (screw cement). True-to-scale diagram. x Assemble as many times as specified (here: twice). Assemble in the specified order. Assemble left and right sides the same way. BRG00 No.BRG00 Ball bearings are optional! (with optional part no.)
BEFORE YOU BEGIN () This kit contains screws and hardware in different metric sizes and shapes. Before using them, check the screws on the true-to-scale diagrams on the left side in each assembly step. Some screws are extras. SCREWS OTHER HARDWARE Screw Self-tapping (TP) Screw Screw WasherNut E-ring mm mm mm Cap Screw TP F/H Screw mm Flat Head (F/H) Screw Set Screw F/H Screw mm Metal BushingBearing mm Pillow Ball mm 0mm 6.8mm 6 Correct Self-tapping (TP) screws cut threads into the parts when being tightened. Excessive force may permanently damage parts when tightening TP screws. It is recommended to stop tightening when the part is attached or when some resistance is felt after the threaded portion enters the plastic. Wrong Overtightened. The threads are stripped. MEMO
ARRANGEMENT OF PLASTIC PARTS ON RUNNERS () No. Use the parts within the dotted lines as tunning options. Shaded parts are not used. 6 6 70 7 7 9 8 7 9 0 No. 6 6 6
ARRANGEMENT OF PLASTIC PARTS ON RUNNERS () No.6 6 Shaded parts are not used. 9 9 9 8 8 8 9 0 89 90 6 7 9 9 9 No.7 Shaded parts are not used. 8 8 6 6 6 6 7 9 9 7
0 ~ 0 are pre-assembled. 8 () Gear Differential (For front and rear) x mm 8 x 6 x mm xmm Set Screw Ball Bearing x 0mm Shim 6 6 6mm O O-ring Flat surface.6 x mm Shaft (Black) 7 () (For center) 6 x x 9 0 0 For front and rear For center Gear Differential x 0mm TP TP F/H Screw.6 x mm Shaft (Black) 6 No.967 Diff. Oil #000 x0mm 8 x 6mm Ball Bearing () (For front and rear) 6 6mm O O-ring 7 8 () (For front and rear) () (For center) () (For center) x x x0mm For front and rear For center Rear Gearbox x 0mm TP TP Screw x0mm x mm TP TP F/H Screw 6 9 x 6mm 0 Thick Thin Shim.6 x 8mm 8 x 6 x mm 8 x 6 x mm Ball Bearing Ball Bearing TP TP F/H Screw 8 9, 0 Adjust the backlash with the shims. 9.6x8mm 9, 0 7 9 xmm.6x8mm Assemble in the specified order. Apply grease. x Assemble as many times as specified. 8
Rear Gearbox x mm Set Screw Tighten the set screw to the flat spot. xmm x mm TP TP Screw S Joint Cup (S) xmm Chassis x mm TP TP F/H Screw xmm xmm 6 Front Gearbox.6 x 8mm TP TP F/H Screw x 0mm TP TP Screw 8 x 6mm Ball Bearing 6 8 x0mm 60 8 x 6 x mm 9 x 6mm 0 Ball Bearing Thick Thin Shim Adjust the backlash with the shims. 9, 0 7 9.6x8mm 9, 0 9.6x8mm x0mm Apply threadlocker (screw cement). Assemble in the specified order. Apply grease. 9
7 Front Gearbox x mm x 0mm Set Screw TP TP F/H Screw 8 L Joint Cup (L) Tighten the set screw to the flat spot. xmm 8 6 x0mm 6 x0mm 8 Chassis x mm TP TP F/H Screw xmm xmm 9 Center Gearbox x0mm 79 78 7mm approx. 7mm x 0mm Screw 78 Brake Caliper 80 8 78 79 Brake Pad (Black) Center Differential 8 79 x0mm 80 x0mm Pay close attention here! Apply rubber type glue. Apply threadlocker (screw cement). 0
0 Center Gearbox x mm TP TP F/H Screw 8 mm O O-ring 7 () (Short) 9 () 86 (Long) 8 9 x 6mm F/H Screw x6mm xmm xmm x6mm START Rear Shock Stay No., No. x0mm x0mm x 0mm Cap Screw x 0mm TP TP Screw x0mm x mm TP TP Screw x 0mm Screw mm Flanged Nut x0mm mm Holes for mounting. xmm 6 xmm x0mm Wing Stay 9 No., No. 9 xmm Note the types of screws! xmm 8 0 xmm x mm TP TP Screw x mm TP TP Screw x 0mm Screw xmm x0mm Part bags used. Pay close attention here! Assemble left and right sides the same way.
Rear Suspension x mm Set Screw 9 EE-ring (Silver) 8 x 8mm Shaft (Black) 8 x 6mm 6 x 8 x mm Plastic Collar.6 x 7mm Shaft Ball Bearing For left side. xmm No., No. 9 x mm Set Screw Ò L Ó Ò L Ó marked. 6 8 9 0 xmm For right side. 7 Ò R Ó Ò R Ó maked. Top Bottom mm For adjusting the ground clearance. 6 Adjust the wheel base by using the other spacer instead of 6. Rear Suspension No., No. x mm Set Screw 7.8mm Ball End x.mm approx..mm Rear Suspension x 7mm Shaft No., No. Holes for mounting. For right side. x 0mm E Cap Screw E-ring (Black) 7.8mm Flange Ball For left side. x0mm Part bags used. Assemble left and right sides the same way. x Assemble in the Assemble as many times specified order. as specified. Pay close attention here! True-to-scale diagram.
6 Rear Suspension No. 6 x mm Screw Pin 8 7.8mm Ball 8 6 Holes for mounting. 7 7 Chassis No., No. xmm x 0mm x mm F/H Screw TP TP Screw 8 76 7 6 6 Torque Rod Ball 8 6.8mm L Ball End (L) 76 6.8mm Ball x0mm 8 Front Shock Stay No., No. x 0mm Cap Screw x 0mm Screw x0mm x mm TP TP Screw mm Flanged Nut 6 Holes for mounting. mm x0mm xmm x0mm xmm Part bags used. Assemble in the specified order. Assemble left and right sides the same way. Pay close attention here!
9 Front Suspension No., No. x0mm 6 x 0mm Cap Screw 8 x 6mm Ball Bearing x mm Set Screw 69 Knuckle Collar For right side. ÒRÓ ÒRÓ marked. 66 69 68 For left side. ÒLÓ ÒLÓ marked. 6 67.6 x 7mm Shaft xmm 69 x0mm 0 Front Suspension x mm Set Screw 00 O O-ring No., No., No. 7 7 Only left side. 00 For left side. 9 E E-ring (Silver) E E-ring (Black) For right side. 9 7 xmm 70 7 x 8mm Shaft x 7mm Shaft 9 6 Top For adjusting the ground clearance. Bottom mm Front Suspension No., No., No. 7 x 0mm 76 6.8mm Set Screw Ball 7 9 EE-ring (Silver) 7 x 0mm Shaft (Black) 6 x mm Screw Pin 7 6.8mm Ball End 7 7 76 mm 9 7 9 6mm approx. 6mm 6 Part bags used. Assemble in the Assemble left and right Apply threadlocker Pay close attention here! specified order. sides the same way. (screw cement).
Chassis No., No. x 0mm TP TP Screw x 0mm TP TP F/H Screw 77 x0mm x0mm Center Gearbox No., No., No.6 88 9 xmm x0mm 89 90 9 xmm x0mm 87 mm 9 7mm Use thick one. Bend the rods if they contact the plate. 89 x mm Set Screw 88 87 x 0mm TP TP Screw Steering No., No. Long Short 99 99 98 x0mm x 0mm Screw 96 6 x 0mm Metal Bushing mm Note the direction. Nylon Nut x0mm 98 8 97 96 9 x0mm 98 Steering Collar mm Flanged Nut 99 Steering Pin x 0mm Washer 9 x0mm mm (Nylon Nut) 96 mm 9 mm Part bags used. Pay close attention here! Tentatively tighten. Assemble in the specified order. Ensure smooth, non-binding movement when assembling.
Steering x0mm 0 x0mm No., No., No.6 Long Short 00 Remove these screws and retighten after installing 00..mm approx..mm Note the direction. 9 0 8 x 0mm Screw x0mm mm () (Flanged) x 0mm x mm F/H Screw F/H Screw x0mm mm mm Flanged Nut Nut 0 0 Tapered Collar 8 6.8mm L Ball End (L) xmm 0 x 0mm 9 6.8mm Adjustable Rod Ball (silver) Note the types of screws! mm xmm 6 Engine x 6mm Screw x 0mm Washer 0 x 0mm Shim x0mm Pre-Assembled 0 09 08 07 06 x6mm Part bags used. Assemble left and right sides the same way. Apply threadlocker (screw cement). True-to-scale diagram. Pay close attention here! 6
7 Engine No. 7 Pulling starter as shown, settle the engine. 7 Insert a sheet of paper before installing. x 8mm Screw Front x8mm x8mm 8 Muffler No., No. x 0mm F/H Screw mm Nylon Nut x mm Set Screw mm Washer mm 9 mm 98 9 8 Manifold x0mm xmm Bend so it fits into the muffler. 96 Muffler Short Long Part bags used. Cut off excess. 7
9 Fuel Tank x mm TP TP Screw x 0mm TP TP F/H Screw 8 No., No., No.6 xmm 8 xmm No.876 To protect the engine from dirt infiltration, purchase Kyosho's No.876 Fuel Filter. 0mm Cut the Silicone Tube to 0mm Length. Note the types of screws! x0mm x0mm 0 0 00 0 60mm Cut the Silicone Tube to 60mm Length. 0 Radio x 8mm Screw x 0mm Screw x 0mm Screw x 8mm TP TP Screw 7 No., No.6 7 8 x0mm 6 x0mm Switch x8mm x8mm x8mm x8mm Switch 9 mm 9 Radio Antenna Receiver 0 No. Better to fill some sponge between radio box and receiver as well as battery. 0 Hook Pin Battery 0 Part bags used. Pay close attention here! Must be purchased separately! mm mm Drill holes with the specified diameter. 8
Radio No. x 0mm TP TP F/H Screw x0mm x0mm Radio xmm Steering Servo xmm x0mm No., No.6 Throttle Servo x mm TP TP Screw xmm 8 x 0mm TP TP Screw 6 x0mm x 0mm TP TP F/H Screw x mm TP TP Screw Note the types of screws! () (For transponder.) Cords Connect as per radio. 8 x0mm 8 Radio No., No.6 mm 6 0mm Parallel xmm x mm Set Screw 6 Steering Rod Part bags used. Must be purchased separately! Pay close attention here! Cut off shaded portion. mm mm Drill holes with the specified diameter. 9
Radio Throttle Rod No., No.6 7 8 9 xmm Servo Horn x8mm Throttle Rod xmm 9 6 98mm 0mm approx. 0mm 0mm approx. 0mm 7mm approx. 7mm Parallel x mm Set Screw x 8mm TP TP Screw 8 Spring 6 xmm 9 mm Stopper 9 6 Brake Rod 7 xmm Adjuster Rod Cut the xmm 6mm Silicone Tube to 6mm Length. 6 Throttle Linkage Adjustment < > < > < > < Neutral > < High Throttle > < Brake > mm mm 6 6 6 Brake Adjusting Knobs Upper Linkage Ð Rear Brak Lower Linkage Ð Front Brake mm Adjust with this screw the carburetor so it cannot close more than mm. Part bags used. Ensure smooth non-binding movement while assembling. Cut off shaded portion. Tentatively tighten. Must be purchased separately! 0
T H E 7 Engine No., No.6 x 0mm TP TP F/H Screw Rainy Weather 8 9 After putting the cover on, loosen the screw, fit in the plastic washer and screw in the screw again. 0 Soak inner sponge with oil. 8 9 No.98 Air Cleaner Oil x0mm 7 F I N E S T R A D I O C O N T R O L M O D E L S 6 No.7 8 Shock.6mm Nylon Nut Collar (White).6mm Washer 6 Collar (Black) mm O O-ring 8 9 Piston 7 C C-ring 8 6.8mm S Ball End (S) 8 7 6.6mm.6mm 9 0 6 7 () Ð (Short) Ð For Front () Ð (Long) Ð For Rear Fit into groove. 0 () Ð (Short) Ð For Front () Ð (Long) Ð For Rear x x For Front For Rear 9 Shock No.7 Fill in until shock oil nearly overflows. Pull down the piston. Shock Oil Viscosity of Shock Oil changes, depending on temperature. Then, gently move the piston up and down to get rid of air bubbles. 60 6 Insert deeply Check if piston moves smoothly x x Part bags used. Assemble as many times as specified. Must be purchased separately!
0 Shock 6 6.8mm Ball (Black) No.7 xmm 6 86 () Ð (Short) Ð For Front 87 () Ð (Long) Ð For Rear x mm TP TP Screw 6 Adjust Rear Shocks with this part, and make lower arms horizontal to chassis. 6 x x For Front For Rear Shock No.7 7 mm < > < Front > 7 Front Shocks Rear Shocks mm < > < Rear > 6 mm Nylon Nut 6 x mm Screw Pin 6 Wheels Slide the tires into these slots in the wheels. Clean the tire rims with thinner beforehand. 7 Apply instant glue little by little in the order. 8 7 70 8 6 x Part bags used. Tentatively tighten. x Assemble as many times as specified. Assemble left and right sides the same way. Apply instant glue (CA glue, super glue). Ensure smooth, non-binding movement when assembling.
Wheels No.6 < > < Front > 7 7 8 x x 0.mm Shim 7 Wheel Stopper Nut < > < Rear > 7 8xmm In case of vibrations, insert a 7 8xmm shim. 7 7 Side Guard 7 No. 7 x0mm x 0mm TP TP Screw 6 x0mm x0mm Trim the shaded portion away so the exhaust pipe can exit. Body Shell 76 77 Fit to the engine when cutting out. 8mm 8mm 7mm Fit to the muffler when cutting out. Hole for antenna pipe. Part bags used. Assemble left and right sides the same way. Cut off shaded portion. 7mm 7mm Drill holes with the specified diameter.
6 Painting Before painting, use a neutral detergent to remove any oil residues and dirt. Mask the windows from the inside. Refer to the pictures on the box for the color scheme. After painting, remove the protective film from the body shell. Paint the body shell from the inside using KyoshoÕs spray colors. 7 Decals Apply decals to any spots you like.
8 Body Shell No. 79 79 78 79 79 78 78 Wing Plastic Washer Slightly bend the body pins as shown in the diagram for easier removal. 79 Body Pin ADJUSTMENT 6 Part bags used.
Toe Adjustment (Front) Toe - in Tie Rod L Toe - out Adjust the front toe either by making the tie rods longer or by making them shorter. L Length (L) Toe - in Shortening. Steering Characteristics Straightline stability becomes better. Steering becomes milder. Straightline stability becomes worse. Toe - out Steering response becomes quicker. Ensure that the length of both the left and right tie rods is the same. Caster Angle (Front) Making longer. Camber Adjustment L Length (L) Making longer. Upper Rod 6 6 Positive Camber Caster Angle can be changed, with a set Shortening of 89 and 90, instead of 6 and 6. Negative Camber 6 L Front / Rear Front Rear Front Rear Ensure that the length of both Êthe left and right upper rods is the same either by unscrewing or by tightening the set screw. Adjust the front / rear camber either by making the upper rods longer or by making them shorter. Negative Camber Steering Characteristics Positive Camber Steering becomes milder. Rear tire grip becomes worse when entering corners. Enters corners more aggressively. Gives rear tires more grip when entering corners. 6 6 6 89 90 Front sus holder is made for set using. Must use together with 6 and 6 set or 89 and 90 set. 6 6 Caster (High) 89 90 Caster (Low) Steering Characteristics Steering becomes milder. Steering response becomes quicker. Ride Height Ride Height Adjust the front / rear ride height. mm Hex Wrench (mm) Set Screw Toe Adjustment (Rear) Adjust the rear toe by replacing. Steering Characteristics 9 Rear tire slip becomes Toe - in û more important. Neutral steering (Standard) Toe - in û 9 Gives the rear tires more Toe - in û grip when exiting corners. Screwing in the set screw. Unscrewing the set screw. Ride height becomes lower. Ride height becomes higher. Place the chassis on a level surface and lift the front of the model. When setting down the model again, check if both front wheels touch down at the same time. 9 9 No.6 6
OPERATING YOUR MODEL SAFELY WARNING: Do NOT operate the model in the following places and situations: (Non-observance may lead to accidents!) Operate the model in spacious areas with no people around! Do NOT operate it:. on roads!. in places where children and many people gather!. in residential districts and parks!. indoors and in limited space! * Non-observance may account for personal injury and property damage! Always check the dry batteries in the radio! When the dry batteries get weaker, transmission and reception of the radio decrease. You may lose control of your model when operating it under such condition. This may lead to accidents! Keep in mind that people around you may also operate a radio controled model! NEVER share the same frequency with somebody else at the same time! Signals will be mixed and you will lose control of your model. 0 This may lead to accidents! When the model is behaving strangely...! Immediately stop the model and check the reason. As long as the problem is not cleared, do NOT operate it! This may lead to further trouble and unforeseen accidents! WARNING: in order to avoid accidents and personal injury, be sure to observe the following: Handle fuel ONLY outdoors! Vapors and exhausts are very noxious to health! Do NOT put fingers or any objects inside rotating and moving parts! Rotating / moving at high speed, you may be seriously injured! Right after use, do NOT touch equipment on the model such as the engine and muffler, because they generate high temperatures! You may burn yourself seriously touching them! ONLY use glow fuel for radio control models! Because the use of gasoline and kerosene in R/C models ac-- counts for fires, do NOT use them! Fuel is highly inflammable and high-explosive!. NEVER use fuel indoors or in places with open fires and sources of heat!. Store fuel ONLY in cool, dry and dark places out of children's reach! Tightly shut the cap!. Do NOT dispose of empty fuel cans into a fire! There is danger of explosion! NEITHER swallow fuel NOR let it into your eyes! Immediate measures should be taken: if fuel is swallowed, in-- duce vomit-ing. If fuel gets into eyes, rinse them and consult an orphamologist! 7
If you use an engine other than the one included Engine for.-class cars Option parts for using option engines. Plug Joining Pipe Manifold Only using a type of. class engine, which is made crank shaft and pilot shaft as one part (SG shaft only). Muffler No.9 Muffler Joining Pipe No.9 O.S.RZ,, Manifold (O.S.RZ, Picco, Nova Rossi) No.BSW8 Custom Silencer No.96 O.S.RG/GSR Manifold (O.S.RG/GSR) Exchange Diff Ring Gear and Pinion Gear to the option parts shown here. No.IF No.IF No.IF0 No.IF06 Refer below pictures. Linkage is also need to change for your engine. Engine Assemble the following parts with pulling the crankshaft. No.IFW No.IF09 x0mm No.96 No.BRG00 0 08 No.BRG00 x0mm 09 mm No.966 x7x0.mm No.IF08 x6mm No.966 x7x0.mm A number and / or type of shim need to be adjusted depending on the type of engine. Pay close attention here! Must be purchased separately! 8
Insert a sheet of paper before installing. No.IF07 Front x0mm x 6mm F/H Screw x0mm x 0mm Flanged Cap Screw x6mm x6mm MEMO Must be purchased separately! 9
In case using Stabilizer. (Optional Parts) IFW-0 For Front IFW-0 Front Stabilizer Set 9 IFW-0 Use optional parts No.IF-7. x0mm xmm xmm x mm Set Screw x mm.8mm Set Screw Ball x 0mm Set Screw.8mm S Ball End (S) x mm Screw.6 x 8mm TP Stabilizer Ball (Silver) TP F/H Screw 8 xmm Use it as it is. 9 xmm.6x8mm 9 xmm.6x8mm For Rear IF-7 IF-7 Rear Stabilizer Set 9 IF-7 Use optional parts No.IF-7. x0mm xmm xmm x mm Set Screw x mm.8mm Set Screw Ball x 0mm Set Screw.8mm S Ball End (S) x mm Screw.6 x 8mm TP Stabilizer Ball (Black) TP F/H Screw 8 xmm Use it as it is. 9 xmm.6x8mm 9 xmm.6x8mm Pay close attention here! Assemble in the specified order. Assemble left and right sides the same way. Ensure smooth non-binding movement while assembling. 0
< EXPLODED VIEW > Gear Differential IF9 Front / Rear IF0 IF9 6 ORG06 8 IF0 BRG00 IF0 6 ORG06 IF0 0 IF0 9 IF0 BS07 IF06 8 BRG00 IF0 Center IF9 IF0 IF9 6 ORG06 7 IF0 BRG00 IF0 6 ORG06 IF0 0 IF0 IF0 9 BS07 IF8 BRG00 7 IF0 Shock BSW7 6 60 9 6 60 0 9 Rear 87 6 8 Front 6 7 6 6 7 6 6 86 BSW7 6 8 6
INFERNO MP-7. SPORTS < > Parts indentified only by key numbers are not sold individually EXPLODED VIEW 00 KYOSHO CORPORATION / IF 6 IF6 66 98 6 IF BSW 7 BSW 7 Front Shock IF6BL 6 IF 60 IF 9 IF7 77 8 6 98 98 6 98 BRG00 IF 7 Front Diff BS 0 9 IF 70 98 6 8 9 IF 7 IF 7 00 IF0 68 BRG00 IF7 69 BS6 9 IF7 69 IF6 67 BRG00 BS 7 IF IF Front Shock 98 6 IF 6 8 9 IF 7 IF 7 IF6BL IF 8 IF 8 IF BRG00 IF 6 IF 8 IF BRG00 IF 6 FM9 79 IF 0 IF9BL 00 IF 7 IF 76 IF 98 99 98 99 W0 0 96 8 W0 0 IF0BL 97 BS6 9 IF8 9 96 8 98 0 7 IF6 7 IF9KG 7 IF8 IF8 96 IF8 9 9 96 9 FD6 8 FD6 6 IF 76 IF8 6 IF8 8 7 8 FM8 8 IF 6 IF 7 IF 7 8 9 Center Diff IF 88 IF 8 IF 78 79 80 79 78 IF7 9 IF 9 FD6 9 FD6 IF7 8 FD6 9 FD6 7 IF7 790 790 FD6 6 IF 89 IF7 6 IF7 6 FD6 9 IF9BL 90 IF 7 968 0 IF 6 IF 707 IF 87 IF 9 IF7 9 968 0 BS79 96 FM9 79 IF BSW 7 BSW7KG 77 Rear Shock IF IF0BL 6 FM9 79 BSW7KG 78 BSW7KG 78 IF 9 FM9 79 IF 8 8 IF 0 8 IF 9 IF 7 BS 0 9 IF 8 Rear Diff IF IF 86 ORG0 8 IF 6 IF6 BRG00 IF 78 78 79 79 80 IF 8 8 8 IF 90 0 6 7 90 9 8 IF IF 8 IF IF IF IF IF 7 IF9 0 IF IF BS 7 IF 6 BRG00 BRG00 IF 7 8 9 8 9 IF 8 Rear Shock 7 BSW 7 IF9KG 7 7 IF7 IF7 8 IF IF7 IF IF7 8 IF7 970 8 70 9 98 96 GT7 IF 7 77 77 SD LD70 KC 0 KC 09 GT 07 IF6 06 KC 08 IF 9 IF 9 IF 7 IF6 B B E A H I C P P D C F F J O O K M M G L N K J I L H E G D A N
No. No. Part Names Quantity 8x6x) BRG00 Shield Bearing (8x6x) x 60 00 6.8mm BS6 6.8mm Ball 9 x 0 0 BS Shim Set 9 0 7 x 0 BS79 BS07 Switch Boots Bevel Shaft 9 x 9 x 80 0 BS Adapter Pipe 98 x 700 BSW Plastic Parts Set 7 8 9 6 6 x 000 BSW Pressure Top 60 x 00 BSW O O-ring 6 6 x 7 x 800 BSW6 BSW7KG Front Soft Spring 86 x Color Nylon Wing (Fluorescent Green) 77 x 78 x 600 000 BSW7 BSW7 7 0 6 7 8 M Turbo Big Shock (M) 9 60 6 6 6 86 x x 7 6 7 8 L Turbo Big Shock (L) 9 60 6 6 6 87 x x BSW7 BSW7 BSW76 M Shock Shaft (M) 0 x L Shock Shaft (L) x Rear Soft Spring 87 x FM9 FM8 Body Pin Joint 79 x 0 8 x FD6 GP Linkage Set (for GP cars) 6 x GT Pilot Shaft 07 x GT7 IF6 Muffler Knuckle Arm 96 66 97 x 67 x IF7 Knuckle Arm Collar 69 x IF Side Guard 7 7 x IF IF7 T Drive Bevel Gear (T) 8 x 8 x 7 x Linkage Set 9 6 x 9 x IF Steering Pin 98 99 x IF9 IF IF.6xmm.6xmm Shaft 6.8mm 6.8mm Ball 7.8mm 7.8mm Ball x 76 x 8 x IF6 Joint Cup (Sports) x IF6 Flywheel Set 06 x IF0 Differential Shaft Set 8 9 0 x IF0 Differential Bevel Set x 0 x IF0 Differential Case x IF0 Center Differential Shaft 7 x IF06 8mmT 8mm Bevel Gear (T) x SPARE PARTS 800 800 600 600 600 0 600 00 800 800 800 800 800 00 000 0 80 00 00 700 00 70 00 00 800 00 No. Part Names IF0.6x7mm.6x7mm Pin IF Suspension Shaft Set IF Bulkhead Set IF Suspension Plate Set IF Rear Hub Carrier IF Wheel Hub IF6 Wheel Nut FOR JAPANESE MARKET ONLY. No. Quantity x 8 7 7 x 6 7 x 60 x x 6 x 9 x 6 x xmm x xmm Set Screw x 7 x 6 7 x 8 x 00 00 00 600 0 0 90 0 IF8 x8mm Rear Torque Rod Set x8mm Cap Screw x x0mm x0mm F/H Screw x 00 IF9 Rear Wheel Shaft 0 x 70 IF0BL Rear Shock Stay 6 x 70 IF IF 8 0 x Wing Stay 9 x xmm Lower Suspension Arm 7 70 x xmm Set Screw x 00 90 IF Upper Arm Set 7 7 7 x x 700 IF Suspension Holder 6 6 89 90 9 9 x 0 IF6BL Front Shock Stay 6 x 0 IF7 Bumper 77 x 00 IF8 Servo Saver Set 9 9 x set 9 96 x 00 IF9BL Plate Set 90 00 x 700 IF0BL Steering Plate 97 x 00 IF Center Differential Housing 8 8 x 00 IF Brake Cam Set 87 88 x 89 x 60 IF Brake Disk 80 x 0 IF Brake Disk Set 78 79 8 x 80 x 00 9 0 6 7 IF Receiver Box 9 x Screw Set 800 8 9 x 8 x IF6BL Radio Plate x 0 IF7 cc Fuel Tank (cc) x 8 x 800 IF7- IF8 Antiribration Rubber MP-7. Body (MP-7.) 8 x 76 x Masking Seal x 00 000 IF9KG IF 0 Wheel Set (0 spoke-type, Green) 70 x 7mm7mm Wheel Wrench (7mm) Wheel Wrench 7mm x 800 00 IF Center Shaft (Rear) 86 x 0 IF Swingshaft 7 x 60 IF IF Front Hub Carrier (IF) 6 6 x 70 IF6 MP-7. Main Chassis (MP-7. SPORTS) x 000 IF8 6T Spur Gear (6T) x 00 IF9 MP-7.MP-7. Decal Set (MP-7. SPORTS) for MP-7. Decal x 600
SPARE PARTS No. No. Part Names Quantity IF0 Front Wheel Shaft 68 x 800 00 KC Special Clutch Shoe 08 x set 09 0 x 00 LD70 Clutch Bearing x 80 ORG0 Silicone O-ring (P/Orange) 8 x 0 00 ORG06 Silicone O-ring (P6/Orange) 6 x 0 00 SD Z Clutch Bell (Z) x 80 W0 Tapered Washer 0 x 0 0 W6 Super Multi Pin Tire 7 x 000 96 6.8mm 6.8mm Ball End 8 x 00 8 E.mm E-ring (.mm) 9 x 0 0 8 Emm E-ring (mm) x 0 0 No. Part Names No. Quantity BSW7BL Color Nylon Wing (Blue) 000 BSW7W Color Nylon Wing (White) 000 BSW7KO Color Nylon Wing (Fluorescent Orange) 000 BSW7KY Color Nylon Wing (Fluorescent Yellow) 000 BSW7G Color Nylon Wing (Gun Metallic) 000 BSW78 Shock Boots 600 BSW8.mmx9 Shock Piston.mmx Hole instead of 9. IF0 IF07 IF08 6T Spur Gear (6T) Engine Mount Spacer Engine Mount Steel made IF09 IF7 IF IF9BL IF9W IF9KO IF9KY IF9G IFW7 IFW IFW8 IFW9 IFW IFWR mmp mm Flywheel (for P) Rear Stabilizer Set Front Universal Swingshaft 0/ Wheel (0-spoke / Blue) 0/ Wheel (0-spoke / White) 0/ Wheel (0-spoke / Fluorescent Orange) 0/ Wheel (0-spoke / Fluorescent Yellow) 0/ Wheel (0-spoke / Gun Metallic), Wing Stay Collar instead of. aluminum 7 8 Universal Center Shaft (Rear) 7 8 in one piece..6mmx9 Shock Piston.6mmx Hole instead of 9..mmx Shock Piston.mmx Hole SPL SP Big Pressure Shock (L) S 86 Spring (S) RedSuper Soft instead of 86. IFWGR S 86 Spring (S) GreenSoft instead of 86. IFWBL IFWW S 86 Spring (S) BlueMedium instead of 86. S 86 Spring (S) WhiteHard instead of 86. OPTIONAL PARTS 0 900 600 600 00 000 00 800 800 800 800 800 900 600 0 0 00 900 900 900 900 00 FOR JAPANESE MARKET ONLY. No. No. Part Names Quantity 70 KP/KY Fluorescent Strap (Pink,Yellow) 9 x 0 0 00 707 Color Antenna (Yellow) x 6 00 90 HD HD Air Cleaner 6 7 8 9 0 x 800 90 Clutch Spring 09 x 00 968 Snap Pin 0 x 0 00 970 Muffler Stay 8 x 00 98 x0mm x0mm Rod 0 x 00 98 7.8mm 7.8mm Flanged Ball x 00 Some of the parts included are not available as spare parts. Purchase optional parts instead. FOR JAPANESE MARKET ONLY. No. No. Part Names Quantity L 87 IFWR Spring (L) RedSuper Soft 900 00 instead of 87. L 87 IFWGR Spring (L) GreenSoft instead of 87. 900 IFWBL L 87 Spring (L) BlueMedium instead of 87. 900 IFWW L 87 Spring (L) WhiteHard instead of 87. 900 IFW t=.080 Special Disk Plate (t=.0) instead of 80. 00 IFW6 8 Disk Plate Bolt (Long Double Disk) instead of 8. 00 IFW7 SPFEMCA SP Silencer (FEMCA) high-power muffler 6800 IFW R 86 Universal Center Shaft (R) 86 in one piece. 800 IFW6 SPT SP Clutch Bell (T) 00 IFW7 SPT SP Clutch Bell (T) instead of. 00 IFW PC PC Clutch Shoe for -piece clutch. 600 IFW PC.00 PC Clutch Spring (.00) for -piece clutch. 00 IFWS PC0.90 PC Clutch Spring (0.90) for -piece clutch. 00 IFWM PC0.9 PC Clutch Spring (0.9) for -piece clutch. 00 IFWH PC.0 PC Clutch Spring (.0) for -piece clutch. 00 IFW PC PC Flywheel Nut 0 IFW6 SPML SP Big Pressure Shock (ML) 00 IFW0 SP Special Main Chassis hard anodized 800 IFW0 SP Special Engine Mount Duralumin 00 IFW0.mm Rear Stabilizer Bar (.mm) for Setting 0 IFW0 Front Stabilizer Set Prevent chassis rolling of front. 000 IFW0 SP Special Servo Saver Set Ball Bearing 800 IFW06G 7 Wheel Nut (Gold) instead of 7. 0 IFW06B 7 Wheel Nut (Blue) instead of 7. 0 IFW07G 7 Wheel Hub (Gold) instead of 7. 00 IFW07B 7 Wheel Hub (Blue) instead of 7. 00 IFW08 SP7 Special Upper Rod (Front) instead of 7. 00
No. No. Part Names Quantity SP IFW09 Special Upper Rod (Rear) instead of. 00 00 PCmm IFW0 PC Flywheel (mm) for -piece clutch. 00 IFW IFW IFW Rear Lower Suspension Plate Option for caster angle of rear. Front Torque Rod Set limits chassis rolling. 8, Special Radio Post instead of 8. aluminum 00 700 600 IFW 0 7 Universal Swingshaft (Rear) 0 7 in one piece. 00 IFW.mmx 9 Shock Piston.mmx Hole instead of 9. 0 IFW6BL F70-7S 6 Hard Shock Stay (F) 70-7S instead of 6. 00 IFW7 LSD TCD Gear Set Traction Control Diff 700 IFW8 LSD TCD Assembly (Final) Traction Control Diff 0000 IFW9 LSD TCD Assembly (Center) Traction Control Diff 900 IFW0 Rear Lower Suspension Plate û (Red) 00 707 IFWBL IFW IFW IFW IFW Hard Rear Shock Stay (707) SP SP Brake Disk SP Polished High Strength SP Hard Upper Rod (Front) Hard type SP SP Hard Upper Rod (Rear) Hard type 8T Spur Gear (8T) Steel made IFW7 Front Upper Arm 0¼ Use together IFW8 Front Hub Carrier (0¼) ¼ IFW9 Front Hub Carrier (¼) 90.7 IFW Universal Swing Shaft (90.7) Use together IFW Flywheel Tapered Collet OPTIONAL PARTS 700 800 000 00 00 00 00 00 00 0 FOR JAPANESE MARKET ONLY. No. No. Part Names Quantity IFW6BL Steering Plate Hard type 800 00.8mmmm W06.8mm Hard Ball (w/mm hole) instead of. 00 W07 6.8mmmm9 6.8mm Hard Ball (w/mm hole) instead of 9. 00 W0 Inner Sponge (Low-hight) Install inside of tires. 00 W09 Inner Sponge (round type) Install inside of tires. 00 W66 S/H W68 S/H W68 S-C W69 S/H W60 SS W60 SS-C W6 /H W6 S/H 9 9-9 96 908 9 9 966 BRG00 S/H High-traction Tire (S/H) X High-traction Tire (X-pattern) C-GripXS C-Grip Tire (X pattern S) High-traction Tire (pin type) X SS High-traction Tire (miclo X SS) C-GripX SS C-Grip Tire (miclo X SS) Super Multi Pin Tire High-traction Tire (miclo square) O.S.-RZ,, Manifold (O.S.-RZ, Picco, Nova Rossi) Manifold Spring OPS Manifold (OPS) O.S.-RG Manifold (O.S.-RG) GP0 Muffler Joining Pipe (GP0) Muffler Stay Heat-resistant Muffler Joining Pipe x7mm x7mm Shim Set x0mm x0mm Ball Bearing pcs. 000 000 00 000 000 00 000 900 000 0 800 000 0 600 000 0 000 ACCESSORIES No. Part Names No. Quantity TSW08 Flywheel Puller 00 YKW00 Straight Reamer (.0) 800 706 Color Antenna (Pink) 00 706 Color Antenna (Yellow) 00 70 Special Antenna Holder aluminum 00 70V SP Antenna Holder II 800 790 Color Silicone Tube 00 79 Starter Box 000 79 KP/KY / Fluorescent Silicone Tube Fluorescent Pink / Fluorescent Yellow 00 876 Fuel Filter Shuts out dirt from fuel 000 98 Air Cleaner Oil 000 6909 SP Muffler Belt Set (.-.) 70 69 Spark Booster 800 69 DC Quick Charger (for Spark Booster) 900 76 6V X-FORCE 600 6V X-FORCE 600 Ni-Cd Battery for receiver 800 00 FOR JAPANESE MARKET ONLY. No. No. Part Names Quantity 6v-000mAh 76 6v-000mAh Ni-Cd Battery 000 00 for receiver 80 Special Taper Reamer Best tool for holing bodies. 800 80 &+ Locking Jig & Wrench Cross wrench + plug locker. 800 809B Flywheel Wrench 00 Wrench Set. 876 Maintenance Stand 800 9 Fuel Tube (.x6x000mm) 700 90 Loctite (medium strength) Screw cement. 900 96 Silicone Seal 800 96 Screw Rescure 00 96 Kyosho Special Glue (g) 700 96 Kyosho Special Primer (0ml) 000 96 0cc Quick Fill Fuel Bottle (0cc) aid for fueling 900 96 00cc Quick Fill Fuel Bottle (00cc) aid for fueling 00 966 SP Bearing Liquid 000 9698 Molybden Grease Spray 000 6
No. Part Names No. Qty. 9660 00 Silicone Oil (00) 0 9660 Silicone Oil (0) 00 9660 Silicone Oil (00) 0 for shocks. 600 00 9660 Silicone Oil (0) 00 9660 Silicone Oil (00) 0 96606 Silicone Oil (0) OIL No. No. Part Names Qty. 00 96607 Silicone Oil (00) 96608 00 Silicone Oil (00) 600 for shocks. 600 00 96609 Silicone Oil (600) 800 9660 Silicone Oil (800) 000 96 Silicone Oil (000) 000 for diffs. 600 00 967 Silicone Oil (000) No. FOR JAPANESE MARKET ONLY. Part Names No. Qty. 967 000 Silicone Oil (000) 000 967 Silicone Oil (000) 000 967 Silicone Oil (000) for diffs. 600 00 6000 9676 Silicone Oil (6000) 7000 9677 Silicone Oil (7000) No. 0 0 0 0 0 06 0 8 9 0 6 7 8 9 0 mm Size (mm) Round Head Screw x6x8x0x.6x8.6x0.6x.6x xx6x8x0.6x6.6x8.6x0.6x 7 7 mm.6mm mmmm 0 each 0 each xx6x8x0 x x6x8x0xx xx6x8x0 xx6x8x0 Flanged Nut 00 x6x8x0x xxx6x8 6 7 xx0x.6x.6x.6x6.6x8 7 7 mm mm 0 pcs 0 pcs Bind Screw.6x.6x6.6x8.6x xx6x8x0x xx6x8x0 x6x8x0x xxx8x0 xx8x0x Flat Head Screw.6x8.6x0.6x.6x x6x8x0x xx6x8x0 x8x0xx0 xxx6x8 x0xxx Cap Screw x8x0xx.6x8.6x0.6x.6x x8x0xx xx6x8x0 xx0xx0 x0xx0 xx8x0 xx0x QUANTITY 00 00 00 00 each each each each each each each each SCREWNUT etc. No. 0 7 8 9 0 7 60 6 6 6 6 Round Head Self-Tapping Screw.6x6.6x8.6x0.6x x6x8x0xx xx6x8x0 xx0x x6x8x0 x8x0x x8x0 mm Size (mm) Bind Self-Tapping Screw.6x6.6x8.6x0.6x x6x8x0xx xx6x8x0 x0xx8 Flat Head Self-Tapping Screw Flanged Cap Screw 00 Screw Set Screw x6xxx6 xxxx0 xxx8x xxx6 x0x0 QUANTITY 00 00 Nylon Nut 00 77 78 79.6mm mm mm pcs pcs pcs Flanged Nylon Nut 00 00 80 mm pcs each each 00 0 each 00 each each each each each No. 8 86 80 8 8 8 8 8 86 87 90 FOR JAPANESE MARKET ONLY. QUANTITY E. E.0 E. E.0 E.0 E.0 E6.0 E7.0 E0.0 mm Nut Washer mm.6mmmm mmmm E E-ring 00 00 0 each 0 each 0 0 pcs 0 pcs 0 pcs 0 pcs 0 pcs 0 pcs 0 pcs 6 pcs 6 pcs 7
"Kyosho Direct-Mail-Parts-Order-System" is available only for Japanese market. 00 0 0 0 7 7 6 8 0 0 0 0 7 7 (),00 00 6 8 0 80,680 () () () () ()
No.9
R THE FINEST RADIO CONTROL MODELS http://www.kyosho.co.jp/ 0-00 06-9- () 000800 690- PRINTED IN JAPAN