TF6 面付p

Before beginning assembly, please read these instructions thoroughly! R THE FINEST RADIO CONTROL MODELS INSTRUCTION MANUAL :0 Scale Radio Controlled Electric Powered WD Touring Car TF6 INDEX REQUIRED FOR OPERATION BEFORE YOU BEGIN ASSEMBLY OPERATING YOUR MODEL SAFELY SET UP SHEET EXPLODED VIEW SPARE PARTS & OPTIONAL PARTS UNDER SAFETY PRECAUTIONS This radio control model is not a toy! ~3 ~ 6~7 ~0 ~3 ~ First-time builders should seek the advice of experienced modelers before beginning assembly and if they do not fully understand any part of the construction. Assemble this kit only in places out of children s reach! Take enough safety precautions prior to operating this model. You are responsible for this model s assembly and safe operation! Always keep this instruction manual ready at hand for quick reference, even after completing the assembly. Taking out liability insurance is recoended. Ni-Cd Ni-MH The product you have purchased is powered by a rechargeable battery. The battery is recyclable. At the end of its useful life, under various national / state and local laws, it may be illegal to dispose of this battery into the municipal waste stream. Check with your local solid waste officials for details in your area for recycling options or proper disposal. *SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE. Copyright 00 KYOSHO CORPORATION / 300-T0 No. 300

REQUIRED FOR OPERATION () ch with electronic speed controller and servo radio control set CAUTION: Only use a surface radio with channels and electronic speed controller! (Any other radio is prohibited!) This kit requires a channel radio con-trol set with electronic speed controller. Because there are stick-type and wheel-type transmitters, use whichever fits your convenience best. For more information on the radio control set, refer to its instruction manual. Stick-type ch radio set Wheel-type ch radio set AA-size Batteries (For Transmitter) Suitable servos, receiver & electric speed controller Servo Receiver AA AA Electric speed controller Operation/Receiver Battery and Charger for Ni-Cd Battery A single Ni-Cd battery powers operation and receiver. Batteries listed right are suitable. Use battery charger designed for saddle pack battery. No.ORI00 Carbon Power LiPo 00 (C/7.V) No.ORI0 Carbon Power LiPo 000 (C/7.V) No.ORI0 Carbon Power LiPo 600 (C/7.V) No.ORI0 Carbon Power LiPo 00 (C/7.V) No.ORI09 Carbon Power LiPo 000 (C/7.V) 3 Motor required. No. Part Names No. Part Names ORI00 VORTEX PRO RACING. BRUSHLESS MOTOR 90 ORI07 VORTEX PRO RACING 7. BRUSHLESS MOTOR 90 ORI0 VORTEX PRO RACING 3.0 BRUSHLESS MOTOR 90 ORI0 VORTEX PRO RACING. BRUSHLESS MOTOR 90 ORI0 VORTEX PRO RACING 3. BRUSHLESS MOTOR 90 ORI09 VORTEX PRO RACING 9. BRUSHLESS MOTOR 90 ORI03 VORTEX PRO RACING.0 BRUSHLESS MOTOR 90 ORI0 VORTEX PRO RACING 0. BRUSHLESS MOTOR 90 ORI0 VORTEX PRO RACING. BRUSHLESS MOTOR 90 ORI VORTEX PRO RACING 3. BRUSHLESS MOTOR 90 ORI0 VORTEX PRO RACING. BRUSHLESS MOTOR 90 ORI6 VORTEX PRO RACING 7. BRUSHLESS MOTOR 90 ORI06 VORTEX PRO RACING 6. BRUSHLESS MOTOR 90 ORI7 VORTEX PRO RACING. BRUSHLESS MOTOR 90 Tire / Wheel / Inner Mold /0 This kit does not supply tires and inner Mold. Use tires and Inner Mold for /0 Touring cars. No.90H KC-Slicks Tire (Hard / pcs) No.90M KC-Slicks Tire (Mediam / pcs) No.360H Mold Inner (Hard / Black / pcs) No.360M Mold Inner (Mediam / gray / pcs) No.360S Mold Inner (Soft / White / pcs) Body No.60B Mazda 6 90 Mazda 6 Body 90 No.60LB Mazda 6 90Light Weight Mazda 6 Body 90 (Light Weight) No.60AB 3.0 All-Purpose 90 Dodge Stratus 3.0 All-Purpose Body 90 No.60AL 3.0 Light Weight 90 Dodge Stratus 3.0 Light Weight Body 90 No.6030B Mazda Speed 6 90 Mazda Speed 6 Body 90 No.6030L Mazda Speed 6 90Light Weight Mazda Speed 6 Body 90 (Light Weight) No.603 LTC-R 90 LTC-R Body 90 No.603L LTC-R 90Light Weight LTC-R Body 90 (Light Weight) Pinion Gear No.W609 ~ W600 Pinion Gear (9T~0T) Silicone Oil OIL 00 No.SIL00 ~ SIL0600 Silicon Oil (0~600) OIL 000

REQUIRED FOR OPERATION () Paint and Brush For painting the body, use Kyosho paints for models! PAINT BRUSH No.76007606 KYOSHO SPRAY COLOR CAUTION: Before using spray colors, always read their explanations! MICRON LINE TAPE No. ( x m) (. x m) 3 (. x m) 9 (0. x m) 60 (0.7 x m) Micron Line Tape KYOSHO Super-flexible tape for masking and detail designing jobs. No.967096703 D FLEX COLOR DECAL Self-adhesive super-flexible sheets that bond to polycarbonate - even when applied to curved surfaces. No.97 MASKING SHEET For safe masking jobs, use this plastic masking sheet featuring one self-adhesive edge. Tools required Phillips Screwdriver ( S ) Needle Nose Pliers Wire Cutters CAUTION: Handle tools carefully! Sharp Hobby Knife Awl Scissors Hex Wrench Cross Wrench TOOLS INCLUDED Ball Differential Grease (Blue Cap) Molybdenum Grease (White Cap) No.369 SP KNIFE EDGE REAMER No need to pre-drill! Precise holes ( to ) can be drilled. No.96 KYOSHO KYOSHO Special Glue Instant Glue Special Glue 3

RADIO PREPARATION A new battery must be charged before it is used. Refer to the charger instruction manual for charging. Set up the radio control system as indicated below. Battery 3 Charger Electronic Speed Controller 7 ON OFF 7 ON 9 OFF POWER ON ST.D/R DIGITAL PROPORTIONAL RADIO CONTROL SYSTEM PERFEX KT-3 POWER ST.TRIM TH.TRIM Transmitter 6 0 ON OFF Servo Receiver Switch 3 6 7 Install batteries. (Transmitter) Extend the antenna. (Transmitter) 3 Connect the battery. Extend the antenna. (Receiver) Center the trims. 6 Switch on. (Transmitter) 7 Switch on. (Receiver) Make sure the servos are in coand. 9 0 9 0 Switch off. (Receiver) Switch off. (Transmitter) Retract the antenna. (Transmitter) BEFORE YOU BEGIN () Read through the manual before you begin, so you will have an overall idea of what to do. Check all parts. If you find any defective or missing parts, contact your local dealer or our Kyosho Distributor.

BEFORE YOU BEGIN () 3 How to read the instruction manual: Front Suspension No., No., No.6 This instruction manual uses several symbols. Please note them during the entire assembly. x 0 Metal Bushing 3 King Pin 6 R 7 6. Pillow Ball (Black) L Key Number, Part Name, True-to-scale Diagram, Quantity Used All parts except screws are identified by key numbers. For purchasing spare parts, find the key no. of the part needed in the spare part list and refer to the left column to look up the corresponding order no. Symbols used throughout the instruction manual, comprise: x Part bags used. Assemble as many times as specified (here: twice). Apply threadlocker (screw cement). Assemble in the specified order. Must be purchased separately! Pay close attention here! Apply grease. Tentatively tighten. Assemble left and right sides the same way. Apply instant glue (CA glue, super glue). Cut off shaded portion. True-to-scale diagram. Ensure smooth non-binding movement while assembling. This kit contains screws and hardware in different metric sizes and shapes. Before using them, check the screws on the true-to-scale diagrams on the left side in each assembly step. Some screws are extras. SCREWS OTHER HARDWARE Screw Self-tapping (TP) Screw Screw WasherNut E-ring 3 3 3 Cap Screw TP F/H Screw Flat Head (F/H) Screw Set Screw F/H Screw 3 Metal BushingBearing Pillow Ball 0 6. 6 Self-tapping (TP) screws cut threads into the parts when being tightened. Excessive force may permanently damage parts when tightening TP screws. It is recoended to stop tightening when the part is attached or when some resistance is felt after the threaded portion enters the plastic. Correct Wrong Overtightened. The threads are stripped.

A B ARRANGEMENT OF PLASTIC PARTS ON RUNNERS 9 Shaded Parts are not used. 3 3 3 3 9 9 6 A B C C D D E E F F x 93 90 6 69 3 9 x 7 x 3 0 0 0 0 3 7 30 03 03 03 03 6 6 9 9 3 60 60 3 0 0 79 79 79 S F H 3 30 30 3 x 6 6

Bulkhead 3 x 6 F/H Hex Screw 3 x F/H Hex Screw 3 x 6 Button Hex Screw 0 3 x Button Hex Screw 6 3 x Cap Screw 3 Nut x Set Screw 60 3 x 7 x Plastic Collar 3 3 x 7 x Plastic Collar 3x6 < > Note the direction. No.,No < Center Bulkhead > 7 0 3 6 3x6 0 Note the direction. 9 00 < > < Rear Bulkhead > 7 6 6 3x6 0 3x6 3x6 96 6 x 67 Note the direction. 3 0 67 3x6 3 60 00 3 x 7 x Aluminum Collar(Red) 3 0 3 x 7 x Aluminum Collar(Red) 0 3 x 7 x 3 Aluminum Collar(Red) 3 Note the direction. 0 Note the direction. 3x6 7 00 3x6 Note the direction. 3x6 7 3 x 6. x. Aluminum Collar(Red) 3 x Shaft Note the direction. < > 67 < Front Bulkhead > Suspension Bush(White). S Ball Stud (S) 6 Suspension Bushing Holder(D) 96 69 Suspension Bushing Holder(E) 0 Note the direction. 3 3x6 69 69 6 67 3 0 x 67 3 3 Note the direction. Attach the upper deck and make sure it doesn t twist or slip. Note the direction. Part bags used. Pay close attention here! Assemble left and right sides the same way. 7

Ball Differential 6 x x. Ball Bearing 73.6 x Ball Diffshaft /6 Inch Ball 9 3/3 Inch Ball 3.6 x 6 x Washer 9.6 Nylon Nut 0 x x Ball Bearing Compress with pliers. Remove flashing. x 9 No.3 Apply instant glue (CA glue, super glue). ADJUSTING 7. 9.6 Cut both ends by equal amounts. 6 6 7 9 6 3 Molybdenum Grease (Black) 3 After applying Grease, place eight differential balls between the two thrust washers 3, grouping them around the screw 73. Insert into groove inside. Ball Differential Grease (Clear) (Both sides) 7 3 3 73 3 73 7 7 73 Now, hold the differential case firmly and rotate part 7. If part rotates into the opposite direction to part 7, no further adjustment is necessary. If part does not rotate, screw 73 Before running, attach the tires and re-adjust accordingly. (Refer to P30) is too tight. In this case, gradually loosen screw 73 until part rotates. 3 Rigid Axle x Screw 3 No.3 77 9 Cut at multiple angles so and can pass through. Do not cut too much. 0 x x Ball Bearing 76 77 0x x Aluminium Collar (Red) 9 9 x 9. Pin x 77 Part bags used. Apply instant glue (CA glue, super glue). x Assemble as many times as specified. Apply grease.

Center Shaft No.3 3 x Button Hex Screw 9 x 6 x 0.7 Plastic Collar x Ball Bearing 9 7 3 Front 9 9 x 9. Pin 3 3x 7 9 Drive Train Remove upper deck and upper bulkhead. 6 Drive Train < > < for Front > x 7 No.3 Cut as per the diagram. < > < for Rear > x 7 Note the direction. Cut as per the diagram. Do not cut. Part bags used. Pay close attention here! x Assemble as many times as specified. 9

7 Drive Train No.3 Note the left / right direction. Align notches to the same position on left and right sides. Note the direction. 93 Align notches to the same position on left and right sides. Note the direction. Drive Train Attach upper deck and upper bulkhead. 9 Steering Crank No. 3x6 3 x 6 F/H Hex Screw 6 3 x 6. x 0.7 Aluminum Collar(Red) 37 3x6 36 3 x 6 Button Hex Screw 3 3 x x 0. Washer 3 x 7 x 3 Aluminum Collar(Red) 36 M3 Flat Head Washer(Red) 6 x x. Ball Bearing. S Ball Stud (S) 3 37 3 x 6 Flanged Metal 6 3 6 6 3 3x6 0 Part bags used. Pay close attention here!

0 Steering Servo No. Steering Servo 0 3 x 6 F/H Hex Screw 0 3 x 7 x Aluminum Collar(Red) 36 3x0 3 x F/H Hex Screw 36 M3 Flat Head Washer(Red) 79 36 3 x 0 F/H Hex Screw. S Ball Stud (S) 3 0 3x6 F S H for FUTABA / ORION for SANWA / KO / JR for HiTEC According to the type of servo, change collars on left and right sides. Steering Servo 3. Ball End (Short) No.6 Servo Rod 3 3 09 39. Ball End (Medium) approx. The side with the step is a reverse screw. 0. Ball End (Long) Steering Tie Rod < > < Right > 0 09 3 x Adjust Rod 0 3 x 0 Adjust Rod < > < Left > 0 39 approx.. 0 Projection. Note direction. 39 0 approx.. Projection. Note direction. Projection. Note direction. Part bags used. Pay close attention here! True-to-scale diagram. Must be purchased separately!

Upper Rod 39. Ball End (Medium) No.6 Front Upper Rod < > < Right > 0 09 39 0. Ball End (Long) 6 09 3 x Adjust Rod < > < Left > approx.. 39 09 0 approx.. Rear Upper Rod 0 09 0 The side with the step is a reverse screw. approx.. x 3 Front Suspension x.6 x 3 x Button Hex Screw 3 x 3 Cap Screw. Low Mount Ball Stud (L) 7 x 0 x Ball Bearing 3 x Shaft 66 3 x King Pin Sleeve 33 x 7 x 0.3 Washer Button Hex Screw Set Screw 3 x 6 x 0. Aluminum Collar(Red). S Ball Stud (S) No. < > < Right > Fill groove with grease and attach ball. 9 6 3 Molybdenum Grease (Black) 00 3 x 7 x Aluminum Collar(Red) 06 Aluminum Clamp Wheel Hub() Red 9 3/3 Inch Ball x 7. Pin A A 7 33 7 0 3x3 A 66 66 7 3 Note the direction. 3 06 Projection. Note direction. 9.6x < > < Left > 00 x 3 Top Part bags used. Pay close attention here! Assemble left and right sides the same way. Assemble in the specified order.

Rear Suspension x.6 x Cap Screw Button Hex Screw No. < > < Left > Projection. Note direction. 7 33 7 3 7 < > < Right > 7 x 0 x Ball Bearing 3 9 36 3 07 x 3 3 x 7 x Plastic Collar 3 x Shaft. S Ball Stud (S) 33 x 7 x 0.3 Washer 07 Aluminum Clamp Wheel Hub() Red 9 3/3 Inch Ball x 7. Pin.6x 9 6 36 Molybdenum Grease (Black) Fill groove with grease and attach ball. Stabilizer 3 x 3 Set Screw 3. 3 Stopper 3 Stabilizer Ball 3 x Button Hex Screw 3. Ball End (Short) 3 x 0 Set Screw 3x0 3x3 3 3 3 Match 3 with this width. 3x3 No.6 6 < > < for Left of Rear > < > < for Right of Rear > Tighten from the top. Tighten. 3x3 3 3x3 3x3 < > < for Rear > < > < for Rear > 6. (Silver) < > < for Front > 7. (Black) Apply a small amount of instant glue to the screw and after it dries, tighten the screw. < > < for Left of Front > < > < for Right of Front> 7 < > < for Front > < > < for Front Only > Cut off. 3 Part bags used. Temporarily tighten. Assemble in the specified order. Pay close attention here! Apply grease. Cut off shaded portion. 3 Ensure smooth, non-binding Assemble left and right Assemble front and rear 3 Drill holes with the movement when assembling. sides the same way. the same way. specified diameter. 3

6 Stabilizer < > < for Right of Rear > < > < for Right of Front> < > < for Left of Front > < > < for Left of Rear > 7 Shock Absorber Shock Sponge No.7 03 0 3 0 30 3 Choose piston according to your preference. 6 Put a little oil. 30 Shock Piston () 6 6 3 Apply to the base of the screw. x 3 Shock Piston (3) 6. S Ball End (S) 7 3 x 7 x 3. Plastic Collar 0 E. E E-ring 0~ 63 7 6 Pull down the piston and slowly fill in oil. 3 7 7 3 Move the piston up and down to get rid of air bubbles. 0. Put a little oil. Add oil one more time up to the brim. Tissue Paper 63 7 6 3 O O-ring Shock Oil O O-ring O O-ring (S) 6 X-O X O-ring 9 99 Put an oil. 99 Wipe away excess oil. 6 x Compress the spring and install. Part bags used. Pay close attention here! True-to-scale diagram. Assemble left and right x Assemble as many sides the same way. times as specified.

Shock Absorber No.7 3 x 0 Button Hex Screw 6 3 Plastic Nut 6 6 3x0 3x0 9 Bumper & Body Mount 3 x F/H Hex Screw No. 0 30 0 3 x Button Hex Screw 30 Hook Pin 30 9 7 7 6 Part bags used. Assemble left and right sides the same way.

0 プロポ モーター Radio & Motor 3 アンテナパイプ No. 3 x 6 サラヘックスビス F/H Hex Screw 3 x サラヘックスビス F/H Hex Screw 3 x キャップビス Cap Screw 3 ワッシャー Washer Antenna Pipe 紙枚分のすき間をつくって固定する Tighten the screws with one sheet of paper inserted between both gears. アンプ Electronic Speed Controller モーター Motor 受信機 Receiver アンテナ Antenna 3 両面テープ Double-sided Tape 90 9 9 3x6 9 3x6 3x6 タイヤ Tire No. フランジ付セレーションナット Flanged Serration Nut グラステープ Glass tape 97 x x 0. アルミカラー レッド Aluminum Collar(Red) 9 9 x x アルミカラー レッド Aluminum Collar(Red) バッテリー Battery 97 使用する袋詰 Part bags used. 6 注意して組立てる所 Pay close attention here! 左右同じように組立てる Assemble left and right sides the same way. 別購入品 Must be purchased separately!

Adjustment of the ball differential < > < Ball Differential > < > < Left rear tire > Loosen Tighten Hex Wrench () Changing the belt layout 39. Ball End (Medium) Cut off. 3 Must be purchased separately! TF Servo Stay < > < Completed > 3 0 According to the type of servo, change collars on left and right sides. 36 3x6 3x6 39 39 09 Servo Rod approx. 0 Must be purchased separately! True-to-scale diagram. Cut off shaded portion. 7

OPERATING YOUR MODEL SAFELY WARNING: Do NOT operate the model in the following places and situations: (Non-observance may lead to accidents!) Operate the model in spacious areas with no people around! Do NOT operate it:. on roads!. in places where children and many people gather! 3. in residential districts and parks!. indoors and in limited space! * Non-observance may account for personal injury and property damage! Always check the dry batteries in the radio! When the dry batteries get weaker, transmission and reception of the radio decrease. You may lose control of your model when operating it under such condition. This may lead to accidents! Keep in mind that people around you may also operate a radio control model! NEVER share the same frequency with somebody else at the same time! Signals will be mixed and you will lose control of your model. 0 This may lead to accidents! When the model is behaving strangely...! Iediately stop the model and check the reason. As long as the problem is not cleared, do NOT operate it! This may lead to further trouble and unforeseen accidents! WARNING: in order to avoid accidents and personal injury, be sure to observe the following: Do NOT put fingers or any objects inside rotating and moving parts! Rotating / moving at high speed, you may be seriously injured! After operation, the electric motor and battery are hot! You may burn yourself seriously touching them! Before charging, please carefully read the explanations of the battery and charger unit! While charging, the battery and charger unit get hot! NEVER charge on top of or near easily inflaable material as this will result in fires! NEVER short out batteries!. Do NOT disassemble or modify batteries!. Ensure the cords do NOT trail into rotating and moving parts! Batteries use heavy metals that are noxious to health! NEVER throw them into fires as they will explode! ALWAYS return disused batteries to the shop! Do NOT dispose of them into the usual waste stream!

BATT. BATT. BATT. BATT. BATT. BATT. BATT. / PROPER OPERATING PROCEDURES Fully charge the battery. Check the transmitter batteries. 3 Make sure the throttle control is in neutral. CH- CH- CH- CH- Connect the battery. Extend the transmitter antenna. 6 Switch on the transmitter. ON CH- CH- CH- CH- OFF ON 7 9 Switch on the receiver. Make sure the model steers according to your transmitter inputs. Make sure the speed (electric speed controller) changes according to your transmitter inputs. ON CH- CH- CH- CH- 0 Make sure the running area is safe. / AFTER FINISHING RUNNING 3 After finishing running, collect your car. Do not leave on the racing car. STOP Switch off the receiver. OFF Switch off the transmitter. CH- OFF CH- ON OFF Disconnect the battery. Remove dirt from the chassis. CHECK When NOT using the model, always switch off the receiver and transmitter! Furthermore, disconnect the battery and remove it from the model! This may lead to overheat and fires! 9

TROUBLESHOOTING PROBLEM CAUSE TO SOLVE Steering control servo does not operate. Transmitter and/or receiver is not switched on. Transmitter batteries are weak. Improper radio installation. Switch on. Replace with new batteries. Correct as per radio instruction manual. Motor does not run. Battery capacity is insufficient. Improper radio installation. Loose connectors. Motor trouble. Recharge battery. Correct as per instruction manual. Make connectors tighter with flat head screwdriver. Replace with a new motor. Motor runs but car does not run. Pinion gear is not installed. Or, screw is loose. Tighten screw that holds pinion gear. Not enough speed. Battery capacity is insufficient. Electronic speed controller is not properly adjusted. Recharge battery. Adjust throttle trim (transmitter). Should electronic speed controller not shift into high, readjust it as per instruction manual. Wheels hardly rotate/do not Dirt entered rotating parts on wheels. Clean and regrease. rotate at all. Backlash is too tight. Readjust as per instruction manual. Even when releasing throttle, car does not run. Electronic speed controller is not properly adjusted. Adjust throttle trim (transmitter). Should electronic speed controller not shift into high, readjust it as per instruction manual. 0

SET UP SHEET Name: Date: Truck / City: Event: Front Suspension Upper Spacer: King Pin: Standared UM Upper Spacer: Upper Rod Position: Diff. Position: Knuckle Spacer: Upper Lower Droop: Wheel Spacer: Drive Hub: LAW30R(.) TFW03(.) Ride Height: Sus. Arm Spacer: Front Rear Knuckle Spacer: Sus. Holder Bush: Front Rear In / Out In / Out Sus. Holder Spacer: Sway Bar: Camber Angle: Toe Angle: Front Diff.: Spool Oneway Diff. Notes: Rear Suspension Upper Spacer: Upper Rod Position: Upper Spacer: Sus. Arm Spacer: Front Rear Diff. Position: Wheel Spacer: Drive Hub: LAW30R(.) TFW03(.) Ride Height: Droop: Sus. Holder Bush: Front Rear Sus. Holder Spacer: Sway Bar: Camber Angle: Hub Carrier Spacer: Front Rear Shock Shock Oil: Shock Spring: Diaphragm: Pressure Form: Shock Length: Front Rear Steering Wiper Steering Spacer: Chassis Weight: g Weight: g Battry Position: IN OUT Front Belt Position: Right Left Weight: g Weight: g Weight: g Tire Inserts Tire Wheel Traction Compound st: nd: Coents Motor Battery Body Others Pinion/Spur / ESC Wing nd Gear Ratio:.3 Gear Ratio Track Condition Smooth Bumpy Low Truction Med. Truction High Truction Asphalt Concrete Carpet Indoor Outdoor Coent: Ver..00

/ EXPLODED VIEW 93 TF3B Note that some parts are not sold as spare parts! 7 TF7 77 TF0 TFW00 BRG0 TF0 9 TFW00 TFW00 TFW00-0 76 TF03 TF03 0 W9-0 6 W30V TF3B 6 TF3B TF3B TF07 9 BRG003 7 7 TF3B TF TF 9 9 UM9 7 970-R 00 W0R 9 TFW00 TF0 TF TF0 BRG0 77 TF0 TFW00 7 TF7 TF00 TF0 TF 3 TF0 TF9 3 TF 7 LA36-B 3 TF0 6 TF 9 TF3B -W30003 3 TF0 9 TF 7 TF0 7 TF0 6 TF0 9 TFW0 0 TF0 TF0 UM 3 30 963 W9-0 W30-0 W9-0 W30-0 99 9 W9- W9-09 W30V-0 W9-0 ORG07 ORG03X W30-0 ORG03 W9-0 7 W30V 6 63 0 3 96 TF3 0 W0R 0 03 3 6 6 7 7 3 6 39 UM 6 63 69 TF0-0 TF3 TF 9 TF3B LAW3 67 LA30 67 LAW3 3 TF6H TF3 TF0-0 9700 TF 09 9700-0 UM 0 W0R 3 TF6H TF3 TF0-0 LA TF6H 9 UM0 TF TF-0 TF 3 9663 33 TF-0 0 BRG00 7 9700 970-0R LA3-0 0 9 TF3B 7033 TF0 66 66 9700 00 00 W0R UM9 7 7 BRG00 LAW30R 3 3 TF LAW30R06 06 66 66 9700 TFW009797 0 0 LA3-0 0 0 LA3-0 Copyright 00 KYOSHO CORPORATION /

TF-0 73 TF0 3 BRG00 7 TF7 BRG0 BRG00 7 TF9 0 TF0 6 W9-0 W30V 6 TF0 0 TF0 9 TF0 3 3 TF3 7 TF3B 9 TF3B BRG003 BRG00 6 TF0 6 TF3B TF3B UM9 7 970-R 30 963 TF3B 93 TF03 7 BRG00 6 TF07 TF30 UM0 9 TF03 7 TF9 3 TF BRG0 7 TF7 UM TF3B 9 -NN TF0 TF09 6 LA36-B 9 TFW0 TF06 7 96 TF3 TF W0R TF3B W60 - W600 W0R 0 TF0-0 TF3 TF 6 TF06 7 3 UM LAW3 67 TF 6 LA30 TF6H 0 W0R 60 TF3 3 TF6H TF3 67 LAW3 TF0-0 9 TF-0 LA 0 UM 09 9700-0 UM TF0 UM9 36 W06R 9 UM0 TF TF-0 0 LA3-0 UM9 0-07R 6 6 M9 9 UM TF7 0 0 OTW 37 LA 3 966 6 BRG00 TF6 3 TF 6 BRG00 LAB 0 W06R 36 09 9700- TF 36 9663 33 0 LA3-0 BRG00 7 TFW03 TFW03 07 0 LA3-0 TF3 3 TF6H TF3 TF0-0 0 0 UM TF UM 3 LAB 79 UM9 36 W06R TFW00 TFW03 9 -N06FN-R 0 W0R 3 TF -N06FN-R 3

SPARE PARTS () FOR JAPANESE MARKET ONLY. No. No. Part Names Quantity BRG00 7 x BRG00 6 x 00 0 00 BRG003 BRG0 x x 00 60 BRG00 3 x x 0 LA 37 x 63 LAB 79 x 0 x 3 LA x 0 LA30 x 0 LA3-0 0 0 0 x 60 x 3x3 LA36-B 6 x 3 LA36-B 7 x 3 LAW30R 06 x Mx x 00 LAW3 67 x ORG07 x 0 ORG03X 6 x OTW 0 x 3 TF0 6 7 x 9 x 0 x TF0 7 x 3 TF03 7 x TF0-0 6 69 x 3 x 3 TF3B 6 7 9 90 9 9 93 9 x 73 TF0 73 x 9 x TF 3 x 3x3 x 73 TF3 96 x 6 69 x 3 x 90 TF0 x 90 TF0 x 90 TF03 x 0 x 60 TF0 6 x 0 x 60 TF0 3 x 90 TF06 7 x 30 TF07 x 6 TF0 x 6 TF09 x 6 TF0 9 x 60 TF 0 x 7 TF 6 6 69 x 3 x 00 TF3 3 x 3x x 70 No. No. Part Names Quantity TF 9 x 0 TF 3 x 60 TF6 x 60 TF7 x 90 TF 3 x 0 TF9 7 x 3360 TF0 77 x 0 TF 3 x 9 x 7 TF-0 0 x 9 x 6 00 TF 36 x 9 x 7 TF-0 9 x 9 x 6 00 TF3 3 60 x 73 TF 3 x 0 TF x TF6H TF7 TF-0 TF9 TF30 TFW00 TFW00 TFW00-0 TFW03 TFW0 UM UM0 UM UM9 W0R W0R W06R W30-0 W30-0 W30V W9-0 W9-0 (6P-0T/TF6) (TF6/TF-/) (3x7x//6pcs) x/pcs) x 3 x 7 x 3 x x x 97 9 x 76 x 77 9 x x x 76 x x x 9 07 x x x 9 x 3x3 x 3 39 0 x 6 9 x x x 0 x 6 00 x 6 36 x 0 30 3 x x 3 6 6 63 6 6 7 7 7 99 03 3 x 0 6 x 7 x x 9 0 00 9 7 6 90 60 99 3 3 3 0 7 0 3 0

SPARE PARTS () FOR JAPANESE MARKET ONLY. No. No. Part Names Quantity W9-09 03 x 0 W9-9 x 0 W9-0 6 6 63 6 6 x 0 W30V-0 (3/pcs) 3 x 30 W30-0 (S/pcs) 7 x 0 -N06FN-R x 0 -W3000 3 x 0 0 70 3 33 x 963 30 x 0 0 No. 966 9663 9700 Part Names No. Quantity 0.,0.,0.3 x 0 73 0 0.,0.,0.3 x 0 73 x 66 x 9700-09 x 0 970-0R x 3 970-07R 6 x 3 970-R 7 x 3 x OPTIONAL PARTS () FOR JAPANESE MARKET ONLY. No. No. Part Names Quantity 6 BRG007F 00 0 6 6 7 LA36-0B 3 6 7 LA36-B 6 7 6 7 0 LA36-3B 6 7 6 7 0 LA36-B 6 7 6 7 3 LA36-6B 6 7 6 7 3 TF7 0 TF3 3990 TFW003 09 09 7 TFW 0 0 93 TFW03 UMH 3 39 0 3 39 0 3 W060 6 6 60 W9-30 9 9 0 W9-3 9 9 0 W9-3 9 9 0 W9-6 9 9 0 W60 W606 W607 W60 W609 W6030 W603 W603 W6033 W603 W603 No. No. Part Names Quantity W6036 0 W6037 W603 W6039 W600 W60 W60 W603 W60 W60 W606Z W607 W60 W609Z W600 WBD0 30 360S 7 360M 7 360H 7 907-W 90S 60 90M 60 90H 60 9 0 9606B 9 97030 30

"Kyosho Direct-Mail-Parts-Order-System" is available only for Japanese market. http://kyoshoshop-online.com

No.300 The service mentioned below is available only for Japanese market.

R THE FINEST RADIO CONTROL MODELS www.kyosho.com 3-003 3 06-9- ()300900 6900- PRINTED IN JAPAN