原本 BARCODE PRINTER CL4NX +Wireless LAN CL6NX +Wireless LAN (KITTING MANUAL) A. WWCL05080: W-LAN kit (For Combo) B. WWCL0508: W-LAN kit (For Non-Combo) 3/Feb/204 Production Engineering 2 Group Production Engineer Dept SATO TECHNOLOGY CO.,LTD APPROVED CHECKED INCHARGE MASHIMO 3/Feb/204 SHIRAHAMA 3/Feb/204 YOKOYAMA 3/Feb/204 PE-E30Z04 E30Z04
Revision History Model : Wireless LAN Kitting (CL4NX & CL6NX) Rev Date E.O No. Description Revised Page(s) APR CHK PIC - 3/Feb/204 - 初版発行 - - - - 5/Jan/205-2 版発行 CL6NX ADD FRONT COVER MASHIMO 205..5 SHIRAHAMA 205..5 YOKOYAMA 205..5
Bundied items A.WWCL05080: W-LAN kit (For Combo) Bundied items B. WWCL0508: W-LAN kit (For Non-Combo) R2940xx WLAN PCB ASSY WLAN PCB ASSY K004790xx ANTENNA (WLAN) K004790xx ANTENNA(WLAN) ANTENNA SUB P56098xx WIFI-CCX STICKER NA060022 PLAIN WASHER P56098xx WIFI-CCX STICKER MD3200622 PAN SCREW SW+WS 2 MT360022 HEXAGON NUT
A. For Combo model () WWCL05080: W-LAN kit (For Combo) <Preparation tool and Caution> *Phillips screwdriver: +No. & +No.2 *Wrench (Size: #0) Please turn OFF the power before assembling. Slide & Lift up <Procedure>. Remove () screw, and take-out (2) Cover-LH 2. Remove (3) screw, and take-out (4) Combo-PCB-Set Notes> When remove the cover LH, Please be careful that the cover does not touch the PCB () PAN. SCREW SW+WL (MD440022) (2) COVER LH Deformed Capacitor by contact with the cover Before conversion (4) COMBO PCB SET (3) PAN. SCREW SW+WL (MD4300822) 2pcs
A. For Combo model (2) WWCL05080: W-LAN kit (For Combo) <Procedure> 3. Remove (5) Hole-cap. 4. Pass thru wire of (6) Antenna-Sub into I/F cover hole, (7) Plain-washer and (8) Hexagon-Nut. 5. Set (6) Antenna-Sub to match the convex on bracket, fix it by (8) Hex-nut. tool; Wrench (Size: #0) Disuse (5) HOLE CAP 6. Connect wire of Antenna-Sub to (9) W-LAN-PCB Note> Connect to CN (not CN2) (7) PLAIN WASHER (8) HEXAGON NUT CN W-LAN PCB (6) ANTENNA SUB CN2 7. Connect (9) W-LAN PCB to Combo-I/F, fix it by (0) screw. 8. Connect () Antenna to Antenna-Sub After conversion (2) COMBO +WLAN PCB ASSY (9) W-LAN PCB () ANTENNA (0) PAN SCREW SW+WS (2pcs) Torque:.0~.4 Kg cm
A. For Combo model (3) WWCL05080: W-LAN kit (For Combo) <Procedure> 9. Attach Combo +WLAN PCB ASSY, and fix it by (3) screw 0. Re-attach (4) Cover-LH, fix it by (5) screw When use the Wireless LAN, please facing up the Antenna. When transporting the printer, please facing down the Antenna. After conversion (2) COMBO+ WLAN PCB ASSY (3) PAN. SCREW SW+WL (MD4300822) 2pcs Torque : 7.0~8.0 Kg cm Use Slide (5) PAN. SCREW SW+WL (MD440022) Torque : 4.0~6.0 Kg cm (4) COVER LH
A. For Combo model (4) WWCL05080: W-LAN kit (For Combo) <Procedure>. Paste (6) WIFI/CCX Sticker in figure position. (6) WIFI/CCX STICKER 0mm 0mm
B. For Non Combo model () WWCL0508: W-LAN kit (For Non-Combo) <Preparation tool and Caution> *Phillips screwdriver: +No.2 Please turn OFF the power before assembling. <Procedure>. Remove () screw, and take-out (2) I/F-Cover 2. Connect (3) Antenna to (4) W-LAN ASSY 3. Insert WLAN PCB ASSY to printer, fix it by (5) screw Antenna Disuse (2) I/F COVER () PAN SCREW SW+WL (2PCS) Torque : 7.0~8.0 Kg cm When use the Wireless LAN, please facing up the Antenna. When transporting the printer, please facing down the Antenna. (3) ANTENNA Use (4) W-LAN ASSY (5) PAN SCREW SW+WL (2PCS) Torque : 7.0~8.0 Kg cm
B. For Non Combo model () WWCL0508: W-LAN kit (For Non-Combo) <Procedure> 4. Paste (6) WIFI/CCX Sticker in figure position. (6) WIFI/CCX STICKER 0mm 0mm
<Setting of printer> Must set only when work-start it () Power-ON the printer (2) Set (select, key-in) the WLAN communication setting for printer. Follow the below instructions. a. IPv4 mode: static b. IP-address: 92.68.. c. Subnet mask : 255.255.255.0 d. WLAN MODE: Ad-hoc e. SSID : SATO_PRINTER SOFT-L SOFT-R ENTER Select:Interface ENTER ENTER ENTER ENTER ENTER Select:Network Select:Settings Select:IPv4 Select:Mode Select:static SOFT2 ENTER SOFT2 CANCEL Select:IP Address Input:92.68.. Confirm: Netmask255.255.255.0 POWER off Decision:IPv4 SOFT2 POWER
動作確認方法 Operation check method パソコンのワイヤレスネットワーク接続のプロパティーを選択 インターネットプロトコル (TCP/IPv4) のプロパティーを選択する IP アドレス サブネットマスクを入力する Select the properties of the wireless network connection of the PC. Select the properties of the internet protocol(tcp/ipv4). Input IP address subnet mask. IP ADDRESS : 92.68..0 SUBNET MUSK : 255.255.255.0 2 プリンタにラベルとリボンをセットする Set the label and ribbon to the printer. 3 プリンタの電源を ON にする Printer power ON. 4 ワイヤレスネットワーク接続のアイコンを右クリックする Right-Click the wireless network icon. 5 利用できるネットワークの表示 をクリック Click 利用できるネットワークの表示. 6 SATO_PRINTER を選択する 次に接続を選択する Select SATO PRINTER. Select connect. SELECT SATO_PRINTER 接続を選択する
7 SATO_PRINTER が表示されない場合 If a SATO_PRINTER is not displayed. ネットワークのタスクより ネットワークの一覧を最新の情報に更新 を選択する 更新しても SATO_PRINTER が表示されない場合は 何度か更新を繰り返す 表示されたら 手順 6 から進める The task of network, select update to the latest information. If it does not, repeat several times. If is displayed, from step6. 8 PRINTER の電源 ON Printer power ON. 9 初期画面になったら SOFT-L をクリックする Click SOFT-L key if it becomes the initial screen. 0 Exit the setup wizard? SOFT-R をクリックして Yes を選択する Exit the setup wizard? Click SOFT-R key (Select Yes). SOFT-L をクリックして ONLINE にする Click SOFT-L (ONLINE). 2 TOOL(PET ZERO) を立ち上げる Start the TOOL. 3 ツールの Connection setup の LAN を選択し設定をクリックする Select LAN of the setup.click 設定.
4 IP アドレスが 92.68.. が表示のこと 違っていたら キー操作で入力のこと IP address (92.68..) is displayed. If different key input an IP address. 5 ツールの 設定 をクリックする Click 設定. 6 参照 をクリックして TEST PRINT(TP3) ファイルを選択する Click a 参照, to select the file TEST PRINT(TP3). 7 2 参照 をクリックして DEFAULT SETTING(DB CZ) ファイルを選択する Click a 2 参照, to select the file DEFAULT SETTING(DB CZ). 8 TOOL の 3 TEST PRINT(TP3) をクリックし TEST プリントを印字させる サンプルは保管する Click 3 TEST PRINT (TP3) of a TOOL, and to print the TEST print. Sample storage. 9 初期設定に戻すために TOOL の 4 DEFAULT SETTING(DB CZ) をクリックする Click 4 DEFAULT SETTING(DB CZ) to go back up for initial setting. 20 プリンタの電源を切る Printer power OFF. 3 4 2