Before commencing assembly, please read these instructions thoroughly! R THE FINEST RADIO CONTROL MODELS Size GP WD D AMG Mercedes CLK INDEX REQUIRED FOR OPERATION RADIO PREPARATION BEFORE YOU BEGIN ARRANGEMENT OF PLASTIC PARTS ON RUNNERS ASSEMBLY ADJUSTMENT OPERATING YOUR MODEL SAFELY SPARE PARTS & OPTIONAL PARTS EXPLODED VIEW INSTRUCTION MANUAL Radio Controlled.5 Engine Powered Touring Car Series SuperTen GP FW-0 WD SAFETY PRECAUTIONS This radio control model is not a toy. 5 5 6 7 6 7 8 First-time builders should seek the advice of experienced modellers before commencing assembly and if they do not fully understand any part of the construction. Assemble this kit only in places out of children's reach! Take care before operating this model. You are responsible for this model's assembly and safe operation! Always keep this instruction manual ready at hand for quick reference, even after completing the assembly. SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE. No. 00 000 KYOSHO
R REQUIRED FOR OPERATION () Minimum channel radio with servos, and battery box. CAUTION: Only use a surface radio with channels and servos! Stick-type ch radio. Battery Box If already included with the radio, no battery box needs to be pur-chased separately. AA-size Batteries AA AA AA Because there are stick-type and wheel-type transmitters, use which ever fits your convenience best. Switch the reverse (transmitter) for the steer-ing and throttle control. For more information on the radio, refer to its instruction manual. Wheel-type ch radio. Suitable servos & receiver Servo Receiver CAUTION: If servos are not able to install, eaven this size. Need to modify upper deck. Required for engine starting: Engines for R/C models require glow fuel. Be careful not to purchase gasoline or kerosene by mistake; both cannot be used! Also, be very careful when han-- dling glow fuel which is hi-ghly inflamma-- ble and high-explosive! Besides glow fuel, engines also require engine starting equipment. This comprises a glow plug heater (booster cord & batteries) and a plug wrench for removing and installing the glow plug. Glow Fuel & Fuel Pump HANDY FUEL WARNING: Gasoline or kerosene cannot be used. Booster Cord No.70 Plug Wrench Paint and Brush For painting the body, use Kyosho paints for models! PAINT BRUSH No.0 POLYCA COLOR No.760 767 KYOSHO SPRAY COLOR CAUTION: Before using spray colors, always read their explanations! KY OSH O S PR AY CO LO R No.8 (mm x 5m) 8 (.5mm x 5m) 8 (.5mm x 5m) 85 (0.mm x 8m) 860 (0.7mm x 8m) Micron Line Tape KYOSHO No.670 670 D- D FLEX COLOR DECAL No.7 MASKING SHEET MICRON LINE TAPE Super-flexible tape for masking and detail designing jobs. Self-adhesive super-flexible sheets that bond to polycarbonate - even when applied to curved surfaces. For safe masking jobs, use this plastic masking sheet featuring one self-adhesive edge.
REQUIRED FOR OPERATION () Tools required TOOLS INCLUDED Hex Wrench (.5mm, mm,.5mm, 5mm) Phillips Screw Driver (L.M.S) Needle Nose Pliers CAUTION: Handle tools carefully! Sharp Hobby Knife Cross Wrench Wire Cutters Awl Instant Glue Rubber Cement Grease GREASE No.0 LOCTITE Midium Strength To prevent the screws from becoming loose. ROUND CUTTER & SANDER No.8 For trimming bodies. Cutting along curved lines never was so easy! SPECIAL TAPER REAMER No.80 No need to pre-drill! Drills neat mm to 5mm holes directly! RADIO PREPARATION Set up the radio control system as indicated below. 8 ON 0 OFF 5 6 7 8 0 6 7 ON OFF Transmitter Servo START 5 6 7 8 0 Insert AA-size dry batteries. (Transmitter) Extend the antenna. (Transmitter) Insert AA-size dry batteries. (Battery Box) Connect the battery box. Extend the antenna. (Receiver) Center the trims. Switch on the transmitter. Switch on the receiver. Make sure the servos move according to your transmitter inputs. FINISH Switch Switch off the receiver. Switch off the transmitter. Retract the antenna. (Transmitter) Receiver 5
BEFORE YOU BEGIN () Read through the manual before you begin, so you will have an overall idea of what to do. Check all parts. If you find any defective or missing parts, contact your local dealer or our Kyosho Distributor. How to read the instruction manual: Front Suspension 5 x 0mm Metal Bushing No., No.5, No.6 This instruction manual uses several symbols. Please note them during the entire assembly. 5 5 King Pin 6 6 5.8mm Pillow Ball (Black) R 7 L 5 8 Key Number, Part Name, True-to-scale Diagram, Quantity Used All parts except screws are identified by key numbers. For purchasing spare parts, find the key no. of the part needed in the spare part list and refer to the left column to look up the corresponding order no. Symbols used throughout the instruction manual, comprise: mm Drill holes with the specified diameter (here: mm). True-to-scale diagram. Apply instant glue (CA glue, super glue). Cut off shaded portion. Must be purchased separately! Apply grease. Cut off excess. Pay close attention here! x Apply rubber cement. Assemble as many times as specified (here: twice). Tentatively tighten. Ensure smooth non-binding movement while assembling. 0 No.0 Ball bearings are optional! (with optional part no.) Assemble left and right sides the same way. Assemble in the specified order.
BEFORE YOU BEGIN () 5 This kit contains screws and hardware in different metric sizes and shapes. Before using them, check the screws on the true-to-scale diagrams on the left side in each assembly step. Some screws are extras. SCREWS OTHER HARDWARE Screw Self-tapping (TP) Screw Screw Washer Nut E-ring Cap Screw TP F/H Screw mm Flat Head (F/H) Screw Set Screw F/H Screw Metal Bushing Bearing 5mm Pillow Ball mm 0mm 6.8mm 6 Self-tapping (TP) screws cut threads into the parts when being tightened. Excessive force may permanently damage parts when tightening TP screws. It is recommended to stop tightening when the part is attached or when some resistance is felt after the threaded portion enters the plastic. Correct Wrong Overtightened. The threads are stripped. ARRANGEMENT OF PLASTIC PARTS ON RUNNERS No. 0 0 00 0 07 S F H 08 06 0 No. 8 7 8 0 No. 8 5 5 Shaded Parts are not used. 5 5
ARRANGEMENT OF PLASTIC PARTS ON RUNNERS No.5 85 7 70 7 No.6 G-6 G-0 G- G- G-6 6 G- G- G-5 G-5 6 6 G- G- No.7 0 8 6 87 88 86 7 5 No. 0 05 Shaded Parts are not used. 5 6 0
No. Steering Nut 5.8mm Pillow Ball (silver) 6 5 Saver Nut Servo Saver Spring 6 5 mm Steering No..6mm Nut 0 x 6mm Metal Bushing Steering Pin.6mm 5.8mm Pillow Ball (silver) 8.6mm Nylon Nut 0 Steering x 8mm F/H Screw Unicrank Shaft No. 0 5 x 8 x.5mm Plastic Bushing 0 5 x8mm x8mm Cut off shaded portion. Ensure smooth non-binding Apply grease. 0 Ball bearings are optional! movement while assembling. (with optional part no.) 7
Gear Differential No. 0 6 x 8mm TP TP Screw 8 7 x8mm x 0mm Shaft O O-ring 6 7 8 8 0 x8mm x 5 Gearbox No. Firmly tighten the set screws onto the flat spots. xmm 5mm x0mm 5 xmm 5mm Gear Differential 8 x0mm 6 7 xmm Rear x0mm x mm Set Screw 5 x 0mm TP TP Screw (Silver) 8 x mm Ball Bearing 7 5 x 0mm Ball Bearing 8 E E E-ring 5mm Washer Front Firmly tighten the set screws onto the flat spots. x x For Front For Rear Apply grease. x Assemble as many times as specified. Apply threadlocker (screw cement). 8
6 Front Suspension No. < Left > x mm Set Screw mm 5.8mm Pillow Ball (silver) x 8mm Ball Bearing < Right > 0 L L marked 5 5mm Hex Wrench (5mm) 6 x mm Ball Bearing R mm Pillow Ball R R marked 5 xmm 5 mm Pillow Ball Nut Firmly tighten the set screws onto the flat spots. 6 xmm Inside 6 7 Front Suspension x Set Screw x 0mm Set Screw 5.8mm Pillow Ball (silver) 0 No. < Right > 7 < Left >.5mm Hex Wrench (.5mm) x 6 E E E-ring 8 x0mm For adjusting the ride height. E Suspension Shaft (E) D Suspension Shaft (D) 0.5mm 6 mm Ensure smooth non-binding movement while assembling. Assemble left and right sides the same way.
8 Front Suspension No. 5mm approx. 5mm 0 x 0mm TP TP Screw (Silver) < Left > 5.5mm approx. 5.5mm x0mm.5mm Hex Wrench (.5mm) < Right > Tighten this screws reciprocally. Front Suspension No. Front Gearbox Inside Note the direction. x mm TP TP F/H Screw O O-ring Note the direction. Front xmm xmm 0 Steering 5 5.8mm L Ball End (L) No. 5 6 5 x 6 x 0mm Set Screw 8mm approx. 8mm Assemble left and right sides the same way. x True-to-scale diagram. Assemble as many times as specified. Apply grease. 0
No. Center Gearbox Front x 6mm TP TP Screw (Silver) x 0mm TP TP Screw (Silver) 8 x mm x0mm x 0mm Ball Bearing Screw 5 7 8 50 50 8mm Aluminium Spacer x 0mm Shaft x6mm x0mm 5 Note the direction. 5 Center Gearbox x mm Set Screw x Set Screw x mm Screw 55 57 5 Brake Piston xmm No. x 55 6mm xmm 5 60 Note the direction for 5 and 60. 60 xmm 5 Top 58 5 60 57 5.5mm approx. 5.5mm 56 Firmly tighten the set screws onto the flat spots. xmm Center Gearbox No. x mm TP TP F/H Screw 6 xmm xmm Apply threadlocker (screw cement). Apply rubber type glue. Assemble in the specified order. Ensure smooth non-binding movement while assembling. Apply grease.
Rear Suspension No.5 x 8mm Ball Bearing < Left > 68 mm Pillow Ball Nut 6 < Right > L L marked 65 67 68 5mm Hex Wrench (5mm) 67 mm Pillow Ball x mm Set Screw 6 66 R R marked 67 67 68 68 xmm 6 6 x mm Ball Bearing xmm Firmly tighten the set screws onto the flat spots. 6 Inside 5 Rear Suspension 70 No.5 < Left > 6 7.5mm Hex Wrench (.5mm) For adjusting the ride height. 7 Suspension Shaft (F) xmm mm 7 C Suspension Shaft (C) 6 6 x0mm 7 x mm Cap Screw 5.8mm Pillow Ball (silver) < Right > 6 6 6 6 6.8mm Ball Use center hole. x 0mm Set Screw 6 7 Ensure smooth non-binding movement while assembling. Assemble left and right sides the same way.
6 Rear Suspension < Right > No.5.5mm approx..5mm mm approx. mm.5mm approx..5mm < Left > Tighten this screws reciprocally..5mm Hex Wrench (.5mm) 7 Rear Suspension No.5 < Right > x0mm x 0mm TP TP Screw (Silver) Note the direction. Front Rear Gearbox 7 Inside Note the direction. < Left > 8 Rear Suspension No., No.5 x mm TP TP F/H Screw O O-ring 76 75 xmm xmm xmm Assemble in the specified order. Assemble left and right sides the same way. Apply grease.
Shock 5 5.8mm L Ball End (L) No.6 77 5 x approx. 78 Shock Shaft G 77 E.5 E E-ring 8 78 7 Cover the shaft with cloth before gripping it with pliers. 77 x 0 Shock Oil No.6 G Pull down the piston 0 ~ mm and slowly fill in oil. 8 0 ~ mm 80 Add oil one more time up to the brim. Piston Then, gently move the piston up and down to get rid of air bubbles. 7 8 7 80 G Put 8 onto 7, wipe up any excess oil and screw on G together with 80. Ensure smooth piston move-ment. Should a piston not move smoothly. x Shock No.6 G6 Compress the spring and install G6. 8 5.8mm Ball G6 G5 8 G Use mm size spacer. 8 mm x x Assemble as many times as specified.
Front Shock No. x mm Cap Screw 8 xmm Rear Shock No.5, No.7 x0mm x0mm x mm Cap Screw x 0mm TP TP Screw (Silver) 86 x0mm x0mm 85 xmm Front Bumper No.7 x 0mm TP TP Screw (Silver) x mm TP TP F/H Screw 87 xmm x0mm Assemble left and right sides the same way. Assemble in the specified order. 5
5 Side Bumpers 88 No.7 x 8mm F/H Screw () FUTABA SRN-F In case of using Futaba SRN-F control block unit assemble left side bumper. x8mm x8mm 8 x8mm x8mm 6 Fuel Tank No.8 Silicone Tube 0mm Cut to one 0mm piece. Silicone Tube 80mm Cut to one 80mm piece. 0 0 Triming x mm TP TP F/H Screw xmm 0 0 0 0 0 50 60 70 80 0 00 0 0 0 0 50 60 70 80 6
7 Engine x 8mm Screw x 8mm F/H Screw No.8 Tighten the screws with one sheet of paper inserted between both gears. Engine Assembly mm Silicone Tube (80mm) x8mm(f/h) x8mm(f/h) x8mm x8mm 8 Engine No., No.8 x mm TP TP F/H Screw 7 7 6 6 x 0mm Cap Screw Nut xmm 5 x mm Set Screw Front View 8 7 0 0 7 Assemble muffler hke picture. xmm x0mm True-to-scale diagram. Cut off excess. 7
No., No. Radio Use the same type of screw as supplied with the servos..6 x 8mm TP.6 x 8mm TP Screw Screw x 0mm TP x 8mm TP Screw (Silver) Screw Steering Servo 0 F In case of using servo horn which come with transmitter. 7 7 5.8mm Pillow Ball (Black).6mm.6mm Nut 5.8mm Pillow Ball (Silver) Nut FUTABA SANWA KO JR HITEC H S F 0 0 00 5~6mm 0 Radio x 0mm TP TP Screw (Silver) x 5mm TP TP Screw x 8mm TP TP Screw No., No. x5mm Throttle Control Servo x8mm 07 x8mm x0mm 0 0 05 x5mm 06 0 x0mm 05 Steering Servo 05 05 Radio Box x 0mm TP TP Screw (Silver) Switch No. 08 x0mm x0mm x8mm.6x5mm x0mm.6 x 5mm Screw x 8mm TP TP Screw 0 Switch 0 Cut off shaded portion. Must be purchased separately! Ensure smooth non-binding movement while assembling. 8
Radio x 0mm TP TP Screw (Silver) No.7 Antenna x0mm Hook Pin x0mm Receiver Battery Box Receiver Connect as per radio instruction manual. If receiver and battery move in the box. Add sponge or some others for holding. Chassis x 0mm TP TP Screw (Silver) 5 x mm Screw x0mm xmm x0mm x0mm Steering No. 0 5 5.8mm L Ball End (L) 0 F 5 x 0mm Adjustable Rod Adjust degree of tightness of both parts and make servo rod look as shown. 5 5 5 5mm approx. 5mm Must be purchased separately! True-to-scale diagram. Pay close attention here!
5 Radio No. x 0mm Screw x0mm x x Set Screw 8 mm Stopper Spring 6 Throttle Rod mm Nylon Nut 7 Brake Rod 6 x 8 Servo Horn mm 7 0 mm 8 Note the top and bottom. 0mm approx.0mm Holes used. 6mm approx. 6mm 6 Radio Tapered Washer No. Silicone Tube Note the direction. Supplied with the servo. Neutral 0mm approx. 0mm 5 7 Throttle Linkage Adjustment ( ) ( High ) No ( ) ( Idle ) mm approx.mm Adjust with throttle stop screw. mm approx.mm ( ) ( Brake ) Contracted. Throttle Stop Screw Position where brake starts working. Confirm the setting before installation. 0 mm Tentatively Ensure smooth non-binding True-to-scale Cut off shaded Must be purchased Cut off excess. mm Drill holes with the tighten. movement while assembling. diagram. portion. separately! specified diameter.
8 Wheels 7 (thin : for front) 8 (thick : for rear) 5 (thin : for front) 6 (thick : for rear) (thin : for front) 0 (thick : for rear) x x For Front For Rear Fit wheels inside tyres as shown. Twist the tyre onto the wheel. After fitting wheels to tyres, apply instant glue as shown. Wheels < Rear > For Rear < Front > Wheel Bolt For Front Cross Wrench 0 Body Mounts No.7 Widen the slit with a screwdriver and fit in Note the direction of and assemble two of the snap. each kind. 5 x Apply rubber type glue. Apply instant glue Assemble as many Assemble left and right (CA glue, super glue). times as specified. sides the same way.
Body Mounts x 8mm TP TP Screw x 0mm TP TP Screw (Silver) x 5mm TP TP Screw x5mm No.7 x0mm < Rear > < Front > 6 7 x8mm x8mm Body Shell 6mm 6mm Cut off shaded portion. Assemble left and right sides the same way. Drill holes with the specified diameter.
Painting Before painting, use a neutral detergent to remove any oil residues and dirt. Mask the windows from the inside. Refer to the pictures on the box for the color scheme. After painting, remove the protective film from the body shell. A- Paint the body shell from the inside using KyoshoÕs spray colors. Yellow B-7 No.760 Black A- Chrome Silver Mask No.760 Yellow Mask No.760 Black Chrome Silver Chrome Silver Chrome Silver Plastic Parts x 6mm TP TP Screw x 8mm TP TP Screw 8 Nut B-7 A- A-0 x6mm Double-sided Tape x8mm B- B- B- x6mm Double-sided Tape x8mm B- Washer B-6 A- x8mm x8mm Do not overtighten the nuts! Pay close attention here!
5 Decals The decal numbers between brackets are only for the opposite side. 5 58 7 8 0 5 7 0 5 7 6 7 5 57 5 56 55 5 55 56 5 57 5 60 6 8 6 7 6 5 78 7 6 7 8 6 ( 6 ) 8 ( ) 0 ( ) 7 6 ( 70 ) 80 0 56 55 77 55 56 5 ( 5 ) 67 ( 68 ) 65 ( 66 ) 6 7 ( 8 ) 7 75 76 6 Body Shell Safety Precautions Always run your car with the body shell mounted! Do not run your car on ground: that is overgrown with grass. that is muddy, sandy or rocky. Check all screws, nuts etc. on a regular basis for looseness. Assemble in the specified order.
Shock Spacer G5 (Shock Spacer) x 0mm TP TP Screw x0mm G0 (Shock Spacer Holder) Installation of Fuel Filter M No.08 Fuel Filter (M) x 0mm TP TP Screw x0mm 0 Transponder Stay 6 Installation of 6 Cooling Fan Set x0mm x0mm 5 x6mm 5 Must be purchased separately! 5
FUTABA SRN-F Installation of FUTABA SRN-F Unit x 0mm TP TP Screw x0mm Switch Boots SRN-F Futaba SRN-F Unit L L marked R R marked In case of using slide type carburetor. Refer follouing picture for assembling. x0mm x 0mm No.7 Screw x x 8 Set Screw 8 mm Stopper mm Ball End 7 Brake Rod 0mm approx. 0mm mm 0 Servo Horn 8 8.6 x 5mm Rod 7 Note the top and bottom. Spring Supplied with the servo. Neutral mm Nylon Nut Tapered Washer 5 6 Must be purchased separately! mm Ensure smooth non-binding Cut off shaded mm Drill holes with the Tentatively tighten. True-to-scale movement while assembling. portion. specified diameter. diagram.
Shock () G5 Adjust the ride height by changing the guantity and / or type of shock collars used. G5 (mm) G5 (mm) G5 (.5mm) ADJUSTMENT Front Suspension Caster Adjust the caster by changing the location of the Spacer. 8 Caster : approx. 8 Caster : approx. û Camber Angle (for front & rear approx. û) û Camber Angle (for front & rear approx. û) Generally, the bigger the caster, the milder cornering becomes. Ride Height 0mm width approx. 0mm G5 Increasing G5 shock collar width. Ride height becomes higher. G5 Decreasing G5 shock collar width. Ride height becomes lower. Camber Adjust the camber by tightening or unscrewing the pillow ball. < Front > Do not loosen too much since will Swingshaft fall out. Shock () Adjust the steering behaviour by changing the spring tension and / or type of shock oil. Spring stiffness Hard Soft Front Sharp Mild Steering characteristics Rear Grip gets lower. Grip gets higher. Camber Angle (Large) Camber Angle (Small) Rear Suspension < Rear > û Adjust camber approx. û.5mm Hex Wrench (.5mm) Steering Characteristics Steering becomes milder. Enters corners more aggressively. Toe Angle approx. û < Spring > Spring stiffness Spring stiffness Silicone Oil Hard # 600 # 500 (660) (6608) # 00 # 00 (6607) (6605) Soft S On-road Shock Spring(S) Yellow Green Orange < Shock Oil > Hard Soft # 00 # 00 (660) (660) approx. û Rear toe angle give stability..5mm û Hex Wrench (.5mm) Adjust camber approx. û Steering Characteristics Camber Angle (Large) Gives rear tires more grip when entering corners. Camber Angle (Small) Rear tire grip becomes worse when entering corners. 7
Operate the model in spacious areas with no people around! Do NOT operate it:. on roads!. in places where children and many people gather!. in residential districts and parks!. indoors and in limited space! * Non-observance may account for personal injury and property damage! OPERATING YOUR MODEL SAFELY CAUTION: Do NOT operate the model in the following places and situations: (Non-observance may lead to accidents!) Handle fuel ONLY outdoors! Vapors and exhausts are very noxious to health! Do NOT put fingers or any objects inside rotating and moving parts! Rotating / moving at high speed, you may be seriously injured! Always check the dry batteries in the radio! When the dry batteries get weaker, transmission and reception of the radio decrease. You may lose control of your model when operating it under such condition. This may lead to accidents! Keep in mind that people around you may also operate a radio control model! NEVER share the same frequency with somebody else at the same time! Signals will be mixed and you will lose control of your model. This may lead to accidents! When the model is behaving strangely...! Immediately stop the model and check the reason. As long as the problem is not cleared, do NOT operate it! This may lead to further trouble and unforeseen accidents! CAUTION: in order to avoid accidents and personal injury, be sure to observe the following: Right after use, do NOT touch equipment on the model such as the engine and muffler, because they generate high temperatures! You may burn yourself seriously touching them! ONLY use glow fuel for radio control models! Because the use of gasoline and kerosene in R/C models ac-- counts for fires, do NOT use them! Fuel is highly inflammable and high-explosive!. NEVER use fuel indoors or in places with open fires and sources of heat!. Store fuel ONLY in cool, dry and dark places out of children's reach! Tightly shut the cap!. Do NOT dispose of empty fuel cans into a fire! There is danger of explosion! NEITHER swallow fuel NOR let it into your eyes! Immediate measures should be taken: if fuel is swallowed, in- -duce vomit-ing. If fuel gets into eyes, rinse them and consult an orphamologist! 8
SPARE PARTS No. No. Part Names Quantity AB-5 Clutch Shoe 5 x 80 00 AB-7 Clutch Spring 5 x 50 BS-6 6.8mm 6.8mm Ball 6 x 0 50 FD- Flywheel Set 5 x 650 FD- Tail Pipe 7 x 0 FD-65 GP x 05 x Linkage Set (for GP cars) 0 0 8 5 x 8 x 00 FM- 5T Clutch Bell (5T) 57 x 00 FZ-0 Gear Box 5 x 00 FZ- Final Differential Case 6 0 6 8 x x 00 FZ- Center Plate 8 x 00 FZ-5 mm mm Pillow Ball x 50 FZ-8 C Suspension Shaft (C) 7 x 50 FZ- Center Shaft (Rear) 75 76 x 00 FZ-5 FW-0 Main Chassis (FW-0) 5 x 000 FZ-5 FW-0 Upper Deck (FW-0) 0 x 00 FZ-5 Knuckle Arm 0 x 500 FZ-5 Rear Hub 65 66 x 500 FZ-55 Front Suspension Arm 0 8 x x 6 600 FZ-56 Rear Suspension Arm 6 6 6 x 600 FZ-57 Front Bulkhead 7 8 x 00 FZ-58 Center Bulkhead 50 5 5 5 8 x 50 FZ-5 Rear Bulkhead 70 7 7 85 x 500 FZ-60 Bumper Set 86 87 88 8 0 x 500 FZ-6 06 07 08 0 x Receiver Box Set 0 50 FZ-6 T Spur Gear (T) 8 x 00 FZ-6 Disk Holder 56 x 00 FZ-6 Spur Gear Shaft 7 x 50 FZ-65 Front Center Shaft 6 x FZ-66 D Suspension Shaft (D) 6 x FZ-67 E Suspension Shaft (E) x FZ-68 F Suspension Shaft (F) 7 x FZ-6 Swingshaft x FZ-70 Brake Lever 5 55 57 x FZ-7 Wheel Shaft x FZ-7 Wheel Stopper Bolt x FZ-7 FZ-7 Drive Washer mm mm Pillow Ball 6 x 67 x FZ-75 FZ-76 FZ-77 mm mm Pillow Ball Nut 68 x mm mm Pillow Ball Nut 5 x 00cc Fuel Tank (00cc) 0 x 00 50 50 50 500 00 50 00 00 50 00 00 000 No. Part Names GT-5 Pilot Shaft LA- Steering Pin LA- Servo Saver Shaft Set x LD-70 Clutch Bearing 56 58 x OR- EG6 7 x EG Body Attachment 5 x OT-5 OT-8 OT- Joint Differential Gear Set O O-ring x x x 0 7 8 x OT-5 OT-6 SPW-5 W-56 8 700 KP,KY 70 KP,KY 0 65 70 70-65 60 68 FOR JAPANESE MARKET ONLY. No. Quantity Upper Rod Set 5 x 5 x 8.6mm.6mm Pillow Ball (Black) 7 x 0 Stainless Disk Rotor 58 x 5 60 x SS 5 78 7 x 77 x Racing Shock (SS) 80 8 8 8 Gx 5.8mm 5.8mm Pillow Ball (Silver) x 8 Fluorescent Strap (S) M Fluorescent Strap (M) 705 Color Antenna (White) 75 S 5 x 0 x x 0 6 x x 6 x Color Silicone Tube 5x0mm 5x0mm Ball Bearing 8xmm 8xmm Ball Bearing 7 x x Air Cleaner x GS5-R GS5-R Engine 50 x Engine Mount Plate x Muffler Gasket x 5 Heat-resistant Muffler Joining Pipe 5 x Snap Pin x 0 Servo Saver Tube 5 6 x Servo Saver Tube Plastic Parts 00 0 0 x x SS 7 Muffler 7 x 7 Manifold x 6xmm 67 6xmm Ball Bearing x OP.5 65 Silicone O-ring P.5 (slim) x 0 x8mm 65 x8mm Ball Bearing x 00 00 50 00 580 600 00 750 00 80 50 000 00 00 80 50 500 00 700 700 500 000 00 00 800 00 500 00 00 600 00 00 800 Some of the parts included are not available as spare parts. Purchase optional parts instead.
W555 5 KP,KY 706 707 70 75 KP,KY 0 OPTIONAL PARTS No. No. Part Names Quantity C 7 FZW- Titanium Suspension Shaft (C) instead of 7. 000 00 7, FZW- Steel Differential Bevel Gear instead of 7,. 00 FZW- 8 Steel Differential Pinion Gear instead of 8. 800 FZW-8 Steel Differential Gear Set 6800 FZW- 8 Carbon Steering Plate instead of 8. 800 FZW-5 6 Hard Deff Case instead of 6. 00 FZW-6 75, 76 Viscus Cup Ring instead of 75, 76. 00 FZW-0 Cycle Fitting Kit When Mounting Cycle Engines 800 FZW-5 5 Hard Main Chassis instead of 5. 5800 FZW-5 0 Carbon Upper Deck instead of 0. 800 FZW-5, Universal Swingshaft instead of,. 000 FZW-5 Front Stabilizer Set 00 FZW-55 Rear Stabilizer Set 00 FZW-56 -Speed Automatic Transmission Set 000 FZW-60 Low Height Engine Mount *Not available with Pull Start Engine. 000 FZW-6 High Balance Flywheel Use with FZW-60. 800 FZW-6 High Balance Flywheel (-speed) Use with FZW-60. 800 FD- CZ-R O.S., Flywheel (CZ-R) for O.S., ENYA Engines 650 W06 5.8mmM.0 8 5.8mm Hard Ball (M.0) instead of 8. hard anodized 500 W07 6.8mmM.0 6 6.8mm Hard Ball (M.0) instead of 6. hard anodized 500 W55 SS Teflon Touring Shock (SS) 00 SS 67 8 08 Adjustable Teflon Shock (SS) 5.8mm 5.8mm Ball End Color Antenna (Fluorescent Pink) Color Antenna (Fluorescent Yellow) Special Antenna Holder 00 5 / instead of 5. Fluorescent Pink / Fluorescent Yellow 00 500 500 500 / Color Silicone Tube instead of. Fluorescent Pink / Fluorescent Yellow 00 5x8mm 5x8mm Ball Bearing instead of. pcs. 000 Air Cleaner Oil 000 M Fuel Filter (M) 000 Urethane Foam Bumper 00 50 0, 6 Steel Final Differential Case instead of 0, 6. 800 6 Cooling Fan Set 800 68 O.S. Special Engine Mount When Mounting O.S. Engines 500 65 FRP 58 FRP Brake Disk instead of 58. 000 65 FRP58 FRP Brake Disk (Thin Type) instead of 58. pcs. 000 66, 7 Tuned Muffler Set (Red) instead of, 7. 6000 67 5 Vespel Clutch Shoe instead of 5. 500 66 SuperTen Tire Box (SuperTen) 600 7 SC Spring Connect Super Tuned Muffler Spring Connect Type 8000 FOR JAPANESE MARKET ONLY. No. No. Part Names Quantity 6v-600mAh 7 6v-600mAh Ni-Cd Battery 800 00 6v-000mAh 76 6v-000mAh Ni-Cd Battery 000 80 & Locking Jig & Wrench 800 8765 Maintenance Stand 800 00 Onroad Spring Set (Hard Type) 800 0 Multi Ride Height Gauge 800 0mm Titanium Adjust Rod 0mm 50 5 6 6 65 66 67 68 660 660 660 660 6605 6606 6607 6608 660 650 650 650 Onroad Spring Set 0mm Titanium Adjust Rod 0mm Muffler Stay T One-piece Clutch Bell T T One-piece Clutch Bell T 5T One-piece Clutch Bell 5T 6T One-piece Clutch Bell 6T 7T One-piece Clutch Bell 7T 8T One-piece Clutch Bell 8T 7 Onroad Spring Set (Soft Type) 7 Clutch Spring (Hard) 5 Dual Spring Assort Set 0 Loctite (medium strength) 6 One-touch Plug Heat Set 50cc 6 Quick Fill Fuel Bottle (50cc) HG 6508 HG Joint Grease 650 Oneway Bearing Grease Team 5 650 Team Circuit Shock (5 different setting), 650 Power Universal Shaft instead of,. 00 50 00 50 Silicone Oil 00 0cc 50 00 500 600 Differential Gear Grease #000 #000 #5000 600 5 instead of 5. pcs. 600 8 instead of 8. types. 800 pcs. for Tie Rod 600 strengthened 600 57, 58 instead of 57, 58. 600 0 5x0mm 600 5x0mm Ball Bearing 800 660 66 66 66 66 665 666 65 650 6505 600 600 600 600 800 500 00 00 800 00 800 800 800 500 800 50 550 700 Silicone Oil 00 0cc 00 00 000 600 #5000 Differential #0000 800 Gear Grease 0
,, WHEEL, TIRE, BODY SET FZ-7G Low Profile Wheel (Gun metallic) x FZ-7W Low Profile Wheel (White) x FZ-80G Low Profile Wide Wheel (Gun metallic) 0 x FZ-80W Low Profile Wide Wheel (White) 0 x FZ-8BK 8-Spoke Wheel (Black) FZ-8S 8-Spoke Wheel (Silver) FZ-8W 8-Spoke Wheel (White) FZ-8BK 8-Spoke Wide Wheel (Black) FZ-8S 8-Spoke Wide Wheel (Silver) FZ-8W 8-Spoke Wide Wheel (White) 600 00 600 600 600 600 700 600 600 700 600 0 0-0- 6 8 85 0 0 05 Mercedes CLK Body Set (AMG Mercedes CLK) D Decal Set (D) decals x WARSTEINER Decal Set (WARSTEINER) decals x GT Body Set (PORSCHE GT) Body Set (CALSONIC SKYLINE) Body Set (ESSO TOM'S CHASER) SOKF-GTR Body Set (SOK McLaren F-GTR) NSX Body Set (Castrol MUGEN NSX) GT Body Set (Castrol Supra GT) 000 00 800 500 00 800 00 00 00 00 68 5R 68 5 68 0 68 0V 68 0 K-ZERO5R K-ZERO Slick Tire 5R K-ZERO5Z K-ZERO Slick Tire 5Z K-ZERO0Z K-ZERO Slick Tire 0Z K-ZERO0V K-ZERO Slick Tire 0V K-ZERO0Z K-ZERO Slick Tire 0Z for Front Molded Mesh High Grip Tires 00 00 00 00 00 00 68 5R 68 5 68 0 68 0V 68 0 K-ZERO5R K-ZERO Slick Tire 5R K-ZERO5Z K-ZERO Slick Tire 5Z K-ZERO0Z K-ZERO Slick Tire 0Z K-ZERO0V K-ZERO Slick Tire 0V K-ZERO0Z K-ZERO Slick Tire 0Z for Rear Molded Mesh High Grip Tires 500 00 500 500 500 500 No. 0 0 0 0 05 06 0 5 8 0 5 6 7 8 0 mm Size (mm) Round Head Screw x6 x8 x0 x5.6x8.6x0.6x.6x x x6 x8 x0.6x6.6x8.6x0.6x 7 7 mm.6mm mm 0 each 0 each x x6 x8 x0 x x6 x8 x0 x x x x6 x8 x0 5 x5 x6 x8 x0 Flanged Nut 00 x6 x8 x0 x x x x6 x8 6 7 x5 x0 x5.6x.6x5.6x6.6x8 7 75 mm 0 pcs 0 pcs Bind Screw.6x.6x6.6x8.6x x x6 x8 x0 x x x6 x8 x0 x6 x8 x0 x x x5 x8 x0 x5 x8 x0 x Flat Head Screw.6x8.6x0.6x.6x x6 x8 x0 x x x6 x8 x0 x8 x0 x5 x0 x x x6 x8 x0 x x x5 Cap Screw x8 x0 x x.6x8.6x0.6x.6x x8 x0 x x x5 x6 x8 x0 x5 x0 x5 x0 x0 x5 x0 x5 x8 x0 x5 x0 x5 QUANTITY 00 00 00 00 each each each each each each each each SCREW NUT etc. No. 0 7 8 50 5 5 57 60 6 6 6 6 Round Head Self-Tapping Screw.6x6.6x8.6x0.6x x6 x8 x0 x x x5 x6 x8 x0 x5 x0 x5 x6 x8 x0 x8 x0 x x8 x0 mm Size (mm) Bind Self-Tapping Screw.6x6.6x8.6x0.6x x6 x8 x0 x x x5 x6 x8 x0 x0 x5 x8 Flat Head Self-Tapping Screw Flanged Cap Screw 00 Screw Set Screw x6 x x x6 x x x5 x0 x x5 x8 x 5x 5x5 5x6 5x0 5x0 QUANTITY 00 00 Nylon Nut 00 77 78 7.6mm mm 5 pcs 5 pcs 5 pcs Flanged Nylon Nut 00 00 80 mm 5 pcs each each 00 0 each 00 each each each each each 65 x0 x5 each No. 85 86 80 8 8 8 8 85 86 87 0 FOR JAPANESE MARKET ONLY. QUANTITY E.5 E.0 E.5 E.0 E.0 E5.0 E6.0 E7.0 E0.0 mm Nut Washer mm.6mm mm 5mm E E-Clips 00 00 0 each 0 each 50 0 pcs 0 pcs 0 pcs 0 pcs 0 pcs 0 pcs 0 pcs 6 pcs 6 pcs
SuperTen FW-0 000 KYOSHO / EXPLODED VIEW < > Parts indentified only by key numbers are not sold individually FZ-7 OR- W-56 FZ-56 6 FZ-60 86 FZ-5 7 FZ-5 7 FZ-6 FZ-5 85 OT-5 OT-8 65 65 FZ- 6 OT- FZ-60 W-56 OT-5 FD-65 7 FD-65 6 FZ-58 8 70 50 FZ- FD-65 0 7 FZ- 6 FZ- 0 FZ-0 5 FZ-5 70 OT-5 FZ-5 66 FZ-0 5 65 FZ-56 6 FZ-56 6 8 7 8 7 FZ-56 6 FZ-68 7 FZ-56 6 BS-6 6 FZ-56 6 FZ-7 67 67 8 7 78 77 77 8 80 8 5 7 FZ-8 7 8 I J FZ-75 68 FZ-7 67 FZ-7 6 FZ-75 68 FZ-7 67 FZ-75 68 FZ-5 65 FZ-60 8 65 FZ-7 FZ-6 FZ-6 0 FZ-7 FZ-8S 0 68 6 8 OT-6 7 8 J E G F C D E H I G H B F C FZ-5 5 LA- LA- FZ-6 OT-5 5 8 OT-5 5 0 OT-5 5 FZ-77 0 FD-65 FZ-5 0 FD-65 0 FD-65 05 FZ-60 0 FZ-6 0 FZ-6 07 FZ-6 75 70- FZ-60 88 0 0 00 8 FZ- 8 5 6 FZ-6 06 FZ-6 08 0 05 FZ- 8 76 75 8 8 0 FZ-58 5 FZ-6 8 FZ-58 50 FZ-6 7 FZ-6 FZ-6 FZ-70 5 FD-65 FZ-70 55 75 7 7 60 5 70 6 7 7 700 65 65 705 FZ-7 LD-70 58 LD-70 56 87 55 FM- 57 FD-65 5 AB-7 5 AB-5 5 GT-5 5 FD- 5 FZ-57 8 FZ-6 FZ-0 OT- FZ-5 0 FZ-55 OT-5 0 7 FZ- 6 FZ- 0 FZ-55 FZ-55 FZ-67 FZ-6 FZ-0 5 FZ-55 0 FZ-66 OT-8 FZ- 6 FZ-65 6 8 FZ-55 FZ-58 5 FZ-58 5 FZ-70 57 FZ-6 56 SPW-5 60 5 5 58 60 OT-5 OT- OT-5 65 65 FZ-55 FZ-57 7 7 8 8 7 A B A OR- 5 6 FZ-60 87 8 6 FZ-7 FZ-8S FZ-7 65 7 5 FZ-5 FZ-5 67 FZ-7 6 8 OT-5 5 OT-5 5 6 FZ-76 5 FZ-5 FZ-76 5 W-56 80 8 77 77 78 7 8 8 D 5 G6 G G G G0 G5 G6 G G G 0
R THE FINEST RADIO CONTROL MODELS -00 5 TEL.06--5 () 0 00 8 00 6000- PRINTED IN JAPAN