3
Press DEL run Setup (F4 on Remote Keyboard) Enter CURRENT Passord:[ ]
Boot Security Exit USB Configuration Module Version - 2.24.0-11.4 Enables USB host controllers. USB Devices Enabled : 1 Keyboard, 1 Mouse, 1 Drive USB Function Legacy USB Support USB 2.0 Controller Mode BIOS EHCI Hand-Off [Enabled] [Enabled] [FullSpeed] [Enabled] USB Mass Storage Device Configuration Select Screen Select Item + - Change Option
Boot Security Exit System Overvie AMIBIOS Core Ver : 08.00.12 Build Date : 07/10/06 BIOS Ver : S38_3A04 Processor Type : Dual-Core AMD Opteron(tm) Processor 2218 Speed : 2600MHz Count : 4 System Memory Size : 8192MB System Time System Date [18:33:54] [Mon 07/24/2006] Use [ENTER], [TAB] or [SHIFT-TAB] to select a field. Use [+] or [-] to configure system Time. Select Screen Select Item + - Change Field Tab Select Field
Boot Security Exit Settings WARNING: Setting rong values in belo sections may cause system to malfunction. Configure the IDE device(s). IDE Configuration SuperIO Configuration USB Configuration S-ATA Configuration EventLog Configuration Remote Access Configuration Onboard Device Configuration Select Screen Select Item Enter Go to Sub Screen
Boot Security Exit IDE Configuration Primary IDE Master Primary IDE Slave : [ATAPI CDROM] : [Not Detected] While entering setup, BIOS auto detects the presence of IDE devices. This displays the status of auto detection of IDE devices. Select Screen Select Item Enter Go to Sub Screen
Boot Security Exit Primary IDE Master Device :ATAPI CDROM Vendor :DV-28E-N LBA Mode :Supported PIO Mode :4 Async DMA :MultiWord DMA-2 Ultra DMA :Ultra DMA-2 Select the type of device connected to the system. Type PIO Mode DMA Mode [Auto] [Auto] [Auto] Select Screen Select Item + - Change Option
Boot Security Exit Configure Nat42x Super IO Chipset Serial Port 1(Address/IRQ): [3F8/IRQ4] Allos BIOS to Select Serial Port1 Base Addresses. Select Screen Select Item + - Change Option
Boot Security Exit USB Configuration Module Version - 2.24.0-11.4 Enables USB host controllers. USB Devices Enabled : 1 Keyboard, 1 Mouse USB Function Legacy USB Support USB 2.0 Controller Mode BIOS EHCI Hand-Off [Enabled] [Enabled] [FullSpeed] [Enabled] Select Screen Select Item + - Change Option
Boot Security Exit USB Mass Storage Device Configuration USB Mass Storage Reset Delay Device #1 Emulation Type [20 Sec] Y-E USB-FDU [Auto] Number of seconds POST aits for the USB mass storage Device after start Unit command. Select Screen Select Item + - Change Option
Boot Security Exit Configure ServerWorks HT1000 S-ATA [Enabled] Enable or Disable HT1000 S-ATA. Select Screen Select Item + - Change Option
Boot Security Exit IPMI Information IPMI Specification Version BMC Firmare Version SDR Firmare Version Event Logging Event Log Area Vie Event Log Clear Event Log LAN Configuration. DHCP Control IP Address Subnet Mask Reset BMC Passord WOL Function 2.0 0.60 2.0 [Enabled] Space Available [Disabled] [192.168.001.002] [255.255.255.000] [Enabled] Enable or Disable All Event Logging Select Screen Select Item + - Change Option
Boot Security Exit Configure Remote Access type and parameters Remote Access [Enabled] Enable Remote Access and Microsoft Windos EMS function. Serial port number Serial Port Mode Flo Control Post-Boot Support Terminal Type VT-UTF8 Combo Key Support [COM1] [115200 8,n,1] [None] [Enabled] [ANSI] [Enabled] Select Screen Select Item + - Change Option
Boot Security Exit Onboard Device Configuration Onboard LAN1/LAN2 : [Enabled] Disabled: Disable the onboard LAN Enabled: Enabled the onboard LAN Select Screen Select Item + - Change Option
Boot Security Exit Configuration AC Lost Handling Button Mode RTC WakeUP From ACPI S4 [Last State] [Instant On/Off] [Disabled] Set the poer state after a shutdon due to an unexpected interrupt of AC poer. Select Screen Select Item + - Change Option
Boot Security Exit Boot Settings Boot Settings Configuration Configure Settings during System Boot. Boot Device Priority Hard Disk Drives ATAPI CDROM Drives Select Screen Select Item Enter Go to Sub Screen
Boot Security Exit Boot Settings Configuration Quick Boot Quiet Boot Bootup Num-Lock PS/2 Mouse Support Wait For F1 If Error MPS Revision [Enabled] [Enabled] [Off] [Auto] [Enabled] [1.4] Allos BIOS to skip certain tests hile booting. This ill decrease the time needed to boot the system. Select Screen Select Item + - Change Option
Boot Security Exit Boot Device Priority 1st Boot Device 2nd Boot Device 3rd Boot Device 4th Boot Device [CD/DVD:PM-DV-28E-N] [RAID:2:WDC WD1600J] [Netork:MBA v8.2.4] [Netork:MBA v8.2.4] Specifies the boot sequence from the available devices. A device enclosed in parenthesis has been disabled in the corrensponding type menu. Select Screen Select Item + - Change Option
Boot Security Exit Hard Disk Drives 1st Drive [RAID:2:WDC WD1600J] Specifies the boot sequence from the available devices. Select Screen Select Item + - Change Option F9 Load Defaults
Boot Security Exit Removable Devices 1st Drive [USB:Y-E USB-FDU] Specifies the boot sequence from the available devices. Select Screen Select Item + - Change Option F9 Load Defaults
Boot Security Exit ATAPI CDROM Drives 1st Drive [CD/DVD:PM-DV-28E-N] Specifies the boot sequence from the available devices. Select Screen Select Item + - Change Option
Boot Security Exit Security Settings Supervisor Passord :Not Installed User Passord :Not Installed Install or Change the passord. Change Supervisor Passord User Access Level Change User Passord Clear User Passord Passord Check [Vie Only] [Setup] Select Screen Select Item Enter Change
Boot Security Exit Exit Options Save Changes and Exit Discard Changes and Exit Discard Changes Load Optimal Defaults Load Failsafe Defaults Exit system setup after saving the changes. F10 key can be used for this operation. Select Screen Select Item Enter Go to Sub Screen