同軸ケーブルアッセンブリ標準品ラインアップ Cable Assemblies Standard-lineup 代表形状 Representatives 両端 BNC(Plug) ケーブルアッセンブリ Both side BNC (Plug) Cable Assemblies Cable Type 0.5m 1m 1.5m 2m RG58A/U BNC001-50-RG58AU BNC001-100- RG58AU BNC001-150- RG58AU BNC001-200-RG58AU 3C-2V BNC116-50-3C2V BNC116-100-3C2V BNC116-150-3C2V BNC116-200-3C2V 3D-2V BNC048-50-3D2V BNC048-100-3D2V BNC048-150-3D2V BNC048-200-3D2V 両端 N(Plug) ケーブルアッセンブリ Both side N (Plug) Cable Assemblies Cable Type 0.5m 1m 1.5m 2m RG58A/U N008-50-RG58AU N008-100-RG58AU N008-150-RG58AU N008-200-RG58AU 3D-2V N009-50-3D2V N009-100-3D2V N009-150-3D2V N009-200-3D2V STAFLEX / 特殊ケーブルアッセンブリ両端 SMA(Plug) 高性能ケーブルアッセンブリ (~20GHz) STAFLEX Cable Assemblies(~20GHz) Both side SMA (Plug) Cable Assemblies with excellent high frequency characteristics and physical flexibility Cable Type 0.5m 1m 1.5m 2m STF358 SMA P-50-STF358 SMA P-100-STF358 SMA P-150-STF358 SMA P-200-STF358 STAFLEXⅡ / 特殊ケーブルアッセンブリ両端 SMA 対応 (PC3.5mm Plug) 高性能ケーブルアッセンブリ (~26.5GHz) STAFLEXⅡ Cable Assemblies (~26.5GHz) Both side SMA applicable connector (PC3.5mm Plug) Cable Assemblies with excellent high frequency characteristics Cable Type 1m 1.5m Soft Cable PC3.5002-100-STF2-S PC3.5002-150-STF2-S Normal Cable PC3.5001-100-STF2-N PC3.5001-150-STF2-N Hard Cable PC3.5002-100-STF2-H PC3.5002-150-STF2-H
同軸ケーブルアッセンブリカスタム品 Cable Assemblies Custom Cable Assemblies カスタム品ご注文時の表記方法 Custom product description ( 例 )(Example) BNC048-N009-50-3D2V 1 2 3 4 * 必ず下記をご確認下さい Please make sure followings 両端それぞれのコネクタの種類 The type of connector on each end ケーブルの種類 / Type of cable ケーブル全長 / Overall length (finished) 1 片端コネクタが BNC048 であることを示します It shows that one end of connector is BNC048 2 片端コネクタが N009 であることを示します ( 両端が同じ場合は省略 ) It shows that other end of connector is N009 (Abbr. if both side is the same connectors) 3 仕上がり全長を示します ( 単位 cm) Total length(unit: cm) 4 使用ケーブルを示します Cable Type 適合ケーブル Applicable Cable コネクタ品名 Connector# コネクタ一般名称 Connector Generic Name 適合ケーブル Applicable Cable コネクタ品名 Connector# コネクタ一般名称 Connector Generic Name 1.5C-2V BNC131 BNC75-BJ-1.5 RG-55A/U SMA055 SMA-P-55 1.5D-2V BNC085 BNC-BJ-1.5 RG-55U BNC199 BNC-P-55 1.5D-2V BNC140 BNC-BJ-1.5( フローティンク ) RG-58A/U BNC009 BNC-J-58 1.5D-2V BNC069 BNC-P-1.5 RG-58A/U BNC014 BNC-LP-58 1.5D-2V SMA003 SMA-P-1.5 圧着タイプ RG-58A/U BNC045 BNC-P-58 2.5D-2V BNC046 BNC-P-2.5 RG-58A/U BNC001 BNC-P-58 3C-2V BNC116 BNC75-P-3 RG-58A/U BNC135 BNC-P-58 圧着タイプ 3C-2V BNC136 BNC-P-3 圧着タイプ RG-58A/U N008 N-P-58 3C-2W BNC076 BNC75-P-3W RG-58A/U SMA060 SMA-P-58 3D-2V BNC011 BNC-J-3 RG-142B/U SMA059 SMA-P-142 3D-2V BNC016 BNC-LP-3 RG-188 SMA053 SMA-P-316 3D-2V BNC048 BNC-P-3 RG-402 N149 N-P-402 3D-2V N009 N-P-3 RG-402 SMA083 SMA-J-402 3D-2W BNC051 BNC-P-3W RG-402 SMA089 SMA-PJ-402 3D-2W N010 N-P-3W RG-402 SMA174 SMA-P-402 5C-2V BNC138 BNC75-P-5 RG-405 SMA086 SMA-PJ-405 5C-2W BNC129 BNC75-P-5W RG-405 SMA082 SMA-J-405 5D-2V BNC007 BNC-P-5 RG-405 SMA088 SMA-PJ-405 5D-2V N011 N-P-5 RG-405 SMA056 SMA-P-405 5D-2W BNC008 BNC-P-5W RG-405 SMA135 SMA-P-405 5D-2W N014 N-P-5W STS-219 SMA245 SMA-P-STS219 * 長さは ご指定に応じます ( 最大 300cm まで ) * 両端共にコネクタの選択は自由です * Regarding the length, you can order up to a maximum 300cm * You can choose the connectors both ends.
同軸ケーブルアッセンブリテストケーブル Cable Assemblies Test Cable Assemblies 代表形状 Representatives 共通仕様 Common Specification 使用ケーブル Cable type 2.5D-QEV 長さ Length 1,000mm バナナプラグ Banana plug バナナ双頭プラグ Banana one head plug ワニ口クリップ Crocodile clip IC クリップ IC clip ワニ口クリップ Crocodile clip SD-SE-100 SD-SF-100 BNC プラグ BNC plug BNC123-SE-100 BNC123-SF-100 BNC123-SD-100 BNC123-SG-100
同軸コネクタの機能分類/機能 Coaxial Connector Classification and Function NO. ① ② ③ ④ 用語説明 Description P : Plug LP : L Type Plug R : Receptacle BR : Bulkhead Receptacle 使用法と機能 結合部軸とケーブル挿入口軸が直線上にある接栓 結合部軸とケーブル挿入口軸が直交するL型接栓 結合部が取付面と直交する接栓座 同上であるが 取付けがナットによって締め付けるもの ⑤ LR : L Type Receptacle 結合部が取付面と平行なL型接栓座 ⑥ ⑦ ⑧ PR : Plug Receptacle J : Jack PJ : Panel Jack 結合部が取付面と直交する接栓座 結合部軸とケーブル挿入口が直線状にある接栓 ケーブルが接続できる接栓座 ⑨ ⑩ ⑪ BJ : Bulkhead Jack A : Adapter PA : Panel Adapter 同上であるが 取付けがナットによって締め付けるもの 二つの結合部軸が直線状にあるアダプタ パネル シャーシなどに取付けて使用するアダプタ ⑫ LA : L Type Adapter 二つの結合部軸が直交するL型アダプタ ⑬ ⑭ TA : T Type Adapter C : Cap 三つの結合部軸がT型のアダプタ 結合部に取付けるキャップ オプショナルツール / Optional Tools ケーブルの圧着 取付け上の作業性 品質保持安定性など それぞれ の目的でオプショナルツールをご活用下さい Our optional tools are recommended for use in efficient and functional cable crimping and mounting Model SST-001 SST-009 SST-002 SST-003 SST-004 SST-005 Tool 圧着工具 Hand Crimping Tool トルクレンチ Torque Wrench ボックススパナ Box Spanner Connector for Use Remarks SS SMB Type SML Type SS Type (6.4HEX) SMA Type (8.0HEX) BNC(BJ) Type N(BJ) Type
ケーブル取付方法 Cabling Procedures BNC-P/(J) 1. ケーブルに締付金具 座金 ガスケットの順に挿入する 次にケーブル外装をカットし クランプを挿入する Install crimping collect, washer, then the gasket on the end of the cable. Cut off the outer jacket of the cable and place the clamp on the cable. N-P/(J) 1. ケーブルに締付金具 座金 ガスケットの順に挿入する 次にケーブル外装をカットし クランプを挿入する Install crimping collect, washer, then the gasket on the end of the cable. Cut off the outer jacket of the cable and place the clamp on the cable. 2. シールドをほぐしてクランプへ折返し カットする 次にケーブル絶縁体をカットする Turn the braid back over the clamp, cut it, then cut off the insulation of the center conductor. 2. シールドをほぐしてクランプへ折返し 余分なシールドをクランプの段に合わせカットする 次にブッシングを挿入し ブッシングの端面に合わせケーブル絶縁体をカットする Turn the braid over the clamp and cut it at the length of the clamp. Next, put the bushing on the cable and cut off the insulation of the center conductor. 3. 中心コンタクトとケーブル芯線を半田付けする Solder the center conductor to the center contact of the connector. 3. 中心コンタクトとケーブル芯線を半田付けする 次に絶縁体を挿入する Solder the center conductor to the center contact of the connector. Then, insert the insulation. 4. 本体へケーブルを挿入し 締付金具で固定する Insert the cable into the shell and fix it with the Crimping Collet. 4. 本体へケーブルを挿入し 締付金具で固定する Insert the cable into the shell and fix it with the Crimping Collet.
ケーブル取付方法 Cabling Procedures BNC-BJ SMB-P/(J), SS-P/(BJ) SML-P 1. 締付金具を挿入してケーブル外装をカットし シールドをほぐさないで広げる Slide clamp nut over cable end, strip cable to dimensions shown and flare shield without loosening. 1. ケーブル外装をカットし フェルールを挿入する Cut off outer jacket at the cable end and insert it into ferrule. 1. ケーブル外装をカットし フェルールを挿入する Cut off outer jacket of the cable end and insert it into ferrule. 2. 余分なシールドをカットして 残りを後方にまくり返し 次にケーブル絶縁体をカットする Trim shield and tuck it up against the cable end and strip center conductor to dimensions shown. 2. シールドをほぐして折返し 余分なシールドをフェルールの段に合わせてカットする 次にケーブル絶縁体をカットする Turn the braid back over the ferrule and cut it at the length of the ferrule. Then, cut the insulation of the cable. 2. シールドをほぐして折返し 余分なシールドをフェルールの段に合わせてカットする 次にケーブル絶縁体をカットする Turn the braid back over the ferrule and cut it at the length of the ferrule. Then, cut the insulation of the cable. 3. 本体 (B) へケーブルを挿入し締付金具をスパナで締めつけた後 芯線を半田付けする Accommodate the cable in Shell(B), pinch it with a spanner and solder the conductor. 3. 中心コンタクトとケーブル芯線を半田付けする Solder the center conductor of the cable to the center contact of the connector. 3. 本体へケーブルを挿入する Insert the cable end into the connector shell. 4. 上記までを完了したら 本体 (A) に挿入して スパナで締付けて完了となる Put Shell (A) on the assembly as above and pinch it with a spanner to complete cabling. 4. 本体へケーブルを挿入し 圧着工具 (SST-001) にてケーブルに圧着する Insert the cable end into the connector shell and crimp it with the SST-01 tool. 4. 圧着工具 (SST-009) にて本体 中心コンタクトの順にケーブルに圧着する 最後に中心コンタクト先端から出ている中心導体をカットする First crimp the connector shell with the SST-009 tool, then crimp the cable. Then, trim the center conductor. * テーパーナットの締付用ボックススパナをご利用下さい Tightening tapered nut is effectively accomplished by use of our optional box wrench.