Creative Sound Blaster Audigy 2 ZS Quick Start Guide This document describes the hardware and software installation of the Creative Sound Blaster Audigy 2 ZS. For more information, refer to the Installation and Application CD. Package contents Sound Blaster Audigy 2 ZS audio card Front audio adapter cable (for HP Workstation xw6000 or xw8000 systems, see the system requirements section) Cable clip Audio connector gasket for digital output Installation and Application CD Regulatory compliance notices Warranty information System requirements HP Workstation xw series (except xw3100) Microsoft Windows XP Service Pack 1 (SP1) or newer operating system Optical drive Empty PCI slot NOTE: If you have an HP Workstation xw8000 or xw6000, you must contact HP support to order the correct front panel adapter cable because the adapter cable in this kit does not support an HP Workstation xw8000 or xw6000. If your system is under warranty, the adapter cable will be provided to you free of charge. For the HP Workstation xw8000, you need the adapter cable with part number 381729-001. For the HP Workstation xw6000, you need the adapter cable with part number 367738-001. To contact support, go to www.hp.com and click the Contact HP link. From there, you can find methods for contacting HP. NOTE: On an HP Workstation xw6000, the rear speaker jack does not automatically mute when a headset, or other speaker, is connected to the front headset port. Warranty information Any warranty information is superseded by the HP warranty term provided in the warranty document.
Systems with Audigy 2 ZS card preinstalled by factory If your system already has an Audigy 2 ZS card preinstalled, the system already contains a driver for basic functionality. To take full advantage of the audio card features, install the driver and applications that are on the Installation and Application CD. NOTE: If you do not install the driver found on the Installation and Application CD or the latest driver from the HP Support & Drivers Web site (http://www.hp.com/go/support), the rear speaker jack does not automatically mute when a headset, or other speaker, is connected to the front headset port. To install the application, skip to step 12 for software installation instructions. Installing the card and software To install the Audigy 2 ZS card: 1. Turn off your computer and unplug the AC power cable. 2. Open the chassis and remove the rear PCI metal slot cover where you plan to install the sound card. 3. Disconnect the front audio cable from the front audio header on the system board. If your system came with a CD audio cable that connects the optical drive to the system board, disconnect the cable from the system board end only and leave the optical drive end conneted. NOTE: The next several steps involve connecting cables to the system board, but it might be easier to connect the cables to the card before connecting the cables to the system board or installing the card. 4. Connect the CD audio cable from the optical drive to the CD_IN connector of the sound card. Skip this step if your system does not have the CD audio cable. The other end should remain connected to the optical disk drive. 5. Connect the P3 header on the adapter cable to the front audio header on the system board. 6. Connect the P1 header on the adapter cable to the J1 header on the audio card. 7. Connect the P2 header on the adapter cable to the header on the front panel audio cable. (The cable removed in step 3.) 8. Install the sound card and secure the brackets. NOTE: The audio card can be installed in any PCI slot, but HP recommends installing the card in an available PCI 32-bit slot. When the sound card is installed in a 64-bit PCI slot, the entire 64-bits bus runs at 32-bits mode. This action can degrade the system performance if another 64-bit PCI device is installed on the same bus. However, if there is no 32-bit PCI bus available, use PCI-X 133 since it is an isolated 64-bit bus slot. 9. Fasten the adapter cable to the bottom of the chassis with the cable clip included in this kit. 10. Close the chassis side cover.
11. Connect the AC power, turn on the computer, and wait for the system to boot. If the new hardware found wizard comes up, click Cancel. 12. Insert the Installation and Application CD into the CD-ROM drive. The installation software starts automatically. Follow the on-screen instructions to install the driver and applications for the sound card. Restart the system when prompted to do so. NOTE: If the application does not start automatically, double-click the setup.exe file in the Installation and Application CD. 13. After you have installed the software, refer to the Online manual or your speaker manufacturer documentation for instructions on how to connect the speaker to your system. To find the online manual, select Start > Programs > Creative > Sound Blaster Audigy 2 ZS > Documentation > Online Manual. NOTE: When the sound card is installed in the system, the internal chassis speaker only functions for diagnostic beeps and does not play any other sound. The rear audio connectors on the system board are also disabled when the Audigy 2 ZS sound card is installed. Use the audio output from the Audigy 2 ZS sound card for audio connection to the external audio device. NOTE: When using the digital out of the sound card, refer to Digital output to prevent Electro Magnetic Interference. Digital output When using the digital output of the sound card, the audio gasket needs to be installed to prevent Electro Magnetic Interference, according to FCC Class B limits. 1. Identify the audio gasket. Audio gasket 2. Install the audio gasket on the audio connector. Audio gasket installed on audio connector (the actual audio connector from the speaker might not look exactly the same as the one in the picture) 3. Now that the audio connector is equipped with the audio gasket, plug the audio connector into the sound card. Audio connector installed into the digital output of the sound card with audio gasket
Creative Sound Blaster Audigy 2 ZS クイックスタートガイド 本書では Creative Sound Blaster Audigy 2 ZS のハードウェアとソフトウェアのインストールについて説明します 詳細につきましては Installation and Application CD を参照してください パッケージの内容 Sound Blaster Audigy 2 ZS オーディオカード フロントオーディオアダプタケーブル ケーブルクリップ デジタル出力用オーディオコネクタガスケット Installation and Application CD 規制遵守の注意点 保証内容 システム要件 HP Workstation xw シリーズ (xw3100 xw6000 xw8000 を除く ) Microsoft Windows XP SP1 (Service Pack 1) 以降のオペレーティングシステム オプティカルドライブ 空の PCI スロット 保証内容 保証書に記載されている保証条件により保証内容は変わります
工場出荷時に Audigy 2 ZS カードがプリインストール済みのシステム お使いのシステムに Audigy 2 ZS カードがプリインストールされている場合 システムには基本的な機能に対応するドライバが実装されています オーディオカードの機能を最大限に活用するには Installation and Application CD 内のドライバとアプリケーションをインストールしてください 注記 : Installation and Application CD 内にあるドライバ または HP Support & Drivers の Web サイト (http://www.hp.com/go/support ( 英語 )) に掲載されている最新のドライバをインストールしていないと ヘッドセットやその他のスピーカーがフロントのヘッドセットポートに接続されている場合に リアスピーカージャックが自動的にミュート状態になりません アプリケーションをインストールするには ソフトウェアのインストール手順 12 へお進みください カードおよびソフトウェアのインストール Audigy 2 ZS カードをインストールするには 以下の手順を実行します 1. コンピュータの電源を切り AC 電源ケーブルを抜きます 2. シャーシを開き サウンドカードを取り付ける場所にあるリア PCI メタルスロットカバーを取り外します 3. システムボードのフロントオーディオヘッダからフロントオーディオケーブルを取り外します CD オーディオケーブルでオプティカルドライブとシステムボードを接続している場合は システムボードに接続している側のケーブルのみを取り外し オプティカルドライブに接続している方はそのまま接続しておきます 注記 : 次のいくつかの手順では システムボードへケーブルを接続する操作を行いますが システムボードへのケーブル接続やカード取り付けの前に カードにケーブルを接続しておくとよいでしょう 4. オプティカルドライブに接続しているCD オーディオケーブルをサウンドカードの CD_IN コネクタに接続します システムに CD オーディオケーブルが搭載されていない場合は この手順をスキップしてください もう片方はオプティカルドライブに接続したままにします 5. アダプタケーブルの P3 ヘッダをシステムボードのフロントオーディオヘッダに接続します 6. アダプタケーブルの P1 ヘッダをオーディオカードの J1 ヘッダに接続します
7. アダプタケーブルの P2 ヘッダをフロントパネルオーディオケーブルのヘッダに接続します ( 手順 3 で取り外したケーブル ) 8. サウンドカードを取り付けて ブラケットを固定します 注記 : オーディオカードは任意の PCI スロットに取り付けることができますが PCI 32 ビットスロットが利用できる場合は このスロットに取り付けることをおすすめします サウンドカードを 64 ビット PCI スロットに取り付けると すべての 64 ビットバスが 32 ビットモードで動作します このとき 同じバスに 64 ビットの PCI デバイスが実装されていると システムのパフォーマンスが低下します もし 32 ビット PCI バスを利用できない場合は 隔離された 64 ビットバススロットである PCI-X 133 を使用してください 9. 付属のケーブルクリップを使用して アダプタケーブルをシャーシの底面に固定します 10. シャーシのサイドカバーを閉じます 11. AC 電源を接続し コンピュータの電源を入れ システムが起動するのを待ちます [ 新しいハードウェア ] ウィザードが起動した場合は [Cancel] をクリックします 12. Installation and Application CD を CD-ROM ドライブに挿入します インストールソフトウェアが自動的に起動します 画面の指示に従い サウンドカードのドライバとアプリケーションをインストールします システムを再起動するようメッセージが表示されたら 再起動を行います 注記 : アプリケーションが自動的に開始しない場合は Installation and Application CD にある setup.exe ファイルをダブルクリックします 13. システムにスピーカーを接続する方法については ソフトウェアをインストールした後 オンラインマニュアル またはスピーカーの製造元のドキュメントを参照してください [Start] [Programs] [Creative] [Sound Blaster Audigy 2 ZS] [Documentation] [ オンラインマニュアル ] の順にクリックすると オンラインマニュアルを参照できます 注記 : サウンドカードがシステムにインストールされると 内部のシャーシスピーカーは診断ビープ音用としてのみ機能し その他の音は出しません Audigy 2 ZS サウンドカードが取り付けられている場合は システムボードのリアオーディオコネクタも無効になります 外部オーディオ装置とオーディオ接続するには Audigy 2 ZS サウンドカードからオーディオ出力してください 注記 : サウンドカードのデジタル出力を使用する場合は 電磁干渉を防ぐために デジタル出力 を参照してください デジタル出力 サウンドカードのデジタル出力を使用する場合 FCC Class B の制限により 電磁干渉を防ぐため オーディオガスケットを取り付ける必要があります 1. オーディオガスケットを確認します オーディオガスケット 2. オーディオガスケットをオーディオコネクタに取り付けます オーディオコネクタに取り付けられたオーディオガスケット ( スピーカーの実際のオーディオコネクタは写真と異なる場合があります )
3. オーディオガスケットが取り付けられたオーディオコネクタを サウンドカードに接続します オーディオガスケットとサウンドカードがデジタル出力に取り付けられたオーディオコネクタ 2004 Hewlett-Packard Development Company, L.P. The HP Invent logo is a registered trademark of Hewlett-Packard Development Company, L.P. 360183-003