Word Class 1

Transcription

1 24 Oct 14 Rev C2 ECONOSEAL* Series J Connector ( コ J コネ タ ) This specification may change without notice, as a result of product design changes and evaluation testing. 1. SCOPE: This specification covers product performance requirements and test methods of ECONOSEAL* Series J Connector, manufactured by TE Connectivity Ltd. 2. APPLICABLE PRODUCTS: Products of the following part numbers and descriptions shall be governed under this specification. NBR Bis-containing Part Number Filler Tip NBR non-bis type φ Pin Contact,Lanceless Descriptions 2φ Pin Receptacle Contact, Lanceless Assembly O Ring Rubber Plug, for 1-Position Connector Rubber Plug, for 2-Position Connector Rubber Plug, for 3-Position Connector Rubber Plug, for 4-Position Connector Rubber Plug, for 8-Position Connector Rubber Plug, for 12-Position Connector Position Plug Housing Position Cap Housing Position Plug Housing Position Cap Housing Position Plug Housing Position Cap Housing Position Plug Housing Position Cap Housing Position Plug Housing Position Cap Housing Position Plug Housing Position Cap Housing Note: Parts number is consisted from listed base number and 1digit numeric prefix and suffix with dash. Refer to catalog or customer drawing for specific part numbers for each base number. When prefix is zero, zero and dash are omitted Tyco Electronics Japan G.K., a TE Connectivity Ltd. Company All Rights Reserved * Trademark タ コ ト ジ パン合 会社 TE Connectivity Ltd. 1 of 28 TE logo is a trademark. Other products, logos, and company names might be trademarks of their respective owners. LOC B

2 3. DEFINITIONS OF TERMS: For the purpose of this product specification, the following terms shall apply Contact: 3.2. Housing: An electrically conductive metallic member, used independently or as a component of a connector assembly to form circuit connection by contacting. pin contact and pin receptacle contacts are available. A dielectric component member of a connector made of insulating material that encapsulate contacts in its contact cavities. In this product line, cap housing that encapsulates pin contacts, and plug housing that encapsulates receptacle contacts are available Rubber Plug: 3.4. Filler Tip, Nylon: 3.5. O Ring: 3.6. Connector: A rubber plug is a cylindrical rubber piece with preformed contact paths pierced through, to provide waterproof connection of contacts, as the plug is used to fill the free opening on the wire side of connector housing. A nylon filler tip is a thin cylinderical tip used to fill a contact path of rubber plug when the plug is applied to connector housing with any of contact position(s) unfilled with contact(s). An O ring is a specifically prepared rubber ring that contains oily element in rubber structure substance, which is used to provide watertight surface matching of connectors as they are mated. This O ring is applied into the groove of cap housing. A connector is an assembly of housing contact(s) and other essential components to make a designated termination. A cap connector consists of a cap housing, pin contact(s), a rubber plug and an O ring, and a plug housing consists of receptacle contact(s) and a rubber plug. 4. MATERIALS AND FINISH: 4.1. Contact: 4.2. Housing: 4.3. Rubber plug: Contact is made from pre-tinplated brass strip conforming to Copper Alloy No.260 of ASTM B36. Housing is made of molded 6/6 Nylon resin. Rubber plug is made of chloroprene rubber (CR). Rev C2 2 of 28

3 4.4. Filler Tip: A filler tip is made of 6/6 Nylon resin O Ring: An O ring is made of nitrile butadiene rubber (NBR) 5. PRODUCT FEATURE, CONSTRUCTION AND DIMENSIONS: 5.1. Contact: Product design feature, construction and dimensions shall be conforming to applicable product drawing(s). All the pin contacts and receptacle contacts must be mated regardless of wire sizes of contact Housing: Product design feature, construction and dimensions shall be conforming to applicable product drawing(s). Housings are provided with polarization device to prevent housings from mismating, and locking mechanism to secure mated housings Rubber Plug: Product design feature, construction and dimensions shall be conforming to applicable product drawing(s) Filler Tip: Product design feature, construction and dimensions shall be conforming to applicable product drawing O Ring: Product design feature, construction and dimensions shall be conforming to applicable product drawing. 6. TEST CONDITIONS: 6.1. Temperature Rating: Temperature rating shall be within the range of -30 and This range includes ambient temperature and temperature rising as a result of loaded current affection Applicable Wires: Contact No. Applicable wire conductor Size Insulation Diameter , 0.85, 1.25, 2.0mm 2 one wire mm 0.5, 0.85mm 2 one wire mm Rev C2 3 of 28

4 7. PERFORMANCE REQUIREMENTS AND TEST METHODS: 7.1. Performance Requirements: When tested in accordance with the test methods specified in para.7.2. and test sequence specified in Para.7.3, product performance shall be conforming to the requirements specified in Table1. Test Items Paragraph No. Appearance (Para ) Contact/Connector Insertion Force (Para.7.2.2) Contact/Connector Extraction Force (Para.7.2.3) Termination Resistance (Low Level) (Para ) Termination Resistance (Para ) Insulation Resistance (Para.7.2.6) Current Leakage (Para.7.2.7) Handling Touch At Assembly (Para.7.2.8) Crimp Tensile Strength (Para ) Water-tight Capability (Para ) Contact Retention Force (Para ) Housing retention Force (Para ) Heat Resistibility (Para ) Cold Resistibility (Para ) Thermal Shock (Para ) Contact Connector Performance Performance (Final) (Initial) (Initial) After Conditioning Products shall be free from cracks, breakage, damages, rattling and loose of parts, rust, fusion and other defects that are detrimental to connector functions N N Pos N Max Pos N Max. 3mΩ max. 3mV/A max MΩ min. 100μ A max. 10mΩ max. 10mV/A max. No tactile; abnormalities to cause operator s fatigue and pain shall be perceived. Wire Size (mm 2 ) Crimp Tensile N Min kPa Min. 58.8N Min. 98.1N Min. 29.4kPa Min. After mechanical and environmental conditioning per sequence of Table 5, performance requirements shall be met. Rev C2 4 of 28

5 7.1 Performance Requirements: Test Items Paragraph No. Kojiri Resistibility (Para ) Water Sprinkle (Para ) Vibration, High Frequency (Para ) Vibration, Low Frequency (Para ) Salt Spray (Para ) Current Cycling (Para ) Liquid Detergent Resistibility (Para ) Oil Resistibility (Para ) Ozon Aging (Para ) Weather Aging (Para ) Contact Performance (Initial) Table 1 (End) (Initial) Connector Performance (Final) After Conditioning After mechanical and environmental conditioning per sequence of Table 5, performance requirements shall be met Test Methods: Appearance: Visually and tactually inspect the product appearance for evidence of abnormalities such as cracks, breakage, rattling and loose of parts, rust, fusion and deformation that are detrimental to connector function Insertion Force of Contact or Connector: Secure one of the mating pair of contacts or connectors on the head of tensile testing machine, and apply an axial push-in load to insert the counterpart contact or connector by operating the head to travel with the speed at a rate of 100 mm a minute. For this test, connectors are tested with the locking mechanism set in effect Extraction Force of Contact or Connector: Secure one of the mated pair of contacts or connectors on the tensile testing machine, and apply an axial pull-off load to separate the contacts or connectors by operating the head to travel with the speed at a rate of 100 mm a minute. For this test, connectors are tested without locking mechanism set in effect. Rev C2 5 of 28

6 7.2.4 Termination Resistance (Low Level): Mated pair of connectors and contacts are tested by applying test current of 50 ma at open circuit voltage of 50 mv DC maximum flowing through the circuit as shown in Fig.1. Millivolt drop of the terminated area shall be measured at the probing points Y and Y which are 75mm apart from wire crimps. Low level resistance is obtained by calculation, after deducting the resistance of 150mm long wire used for termination. Measurements shall be made on the contact positions one after one in the connector. Fig Termination Resistance: Mated pair of connectors and contacts are tested by applying closed circuit current of 1 A at open circuit voltage of 12 V DC flowing through the circuit as shown in Fig.1. After temperature rising becomes stabilized, measure the millivolt drop of the terminated area between the probing points Y and Y, which are 75mm apart from the wire crimps. Termination resistance is obtained after deducting the resistance of 150 mm long wire used for termination. Measurements shall be made on the contact positions one after one in the connector. Probing points Y and Y shall be pretreated by uniform soldering in order to stabilize measurement reading during the test Insulation Resistance: Mated pair of connectors shall be tested by applying test potential of 500 V DC between the adjacent contacts and between the contacts and the ground. Measuring Apparatus Measuring between adjacent contacts Measuring Apparatus Measurement between contacts and the ground Fig.2 Rev C2 6 of 28

7 7.2.7 Current Leakage: Mated pair of connectors shall be tested by applying test current of 28 V DC between the diagonal contact positions as shown in Fig.3. Fig Handling Touch at Assembly: Tactually inspect the handling touch of contacts, as inserted and extracted as if the contacts are handled in practical assembly processing Crimp Tensile Strength: Secure a contact which is crimped on an approximately 100mm-long wire, on tensile testing machine, and apply an axial pull-off load to the end of crimped wire by operating the head to travel with the speed at a rate of 100mm a minute. Crimp tensile strength is determined when the wire is broken or is pulled off from the wire crimp Watertight Capability: Watertight capability of connector is tested by blowing compressed air into inside of connector through a small hole which is made through specifically for testing. For this test, wire ends are watertight finished by soldering and masking by using adhesive material as shown in Fig.4. Test is performed with the connector immersed into water at 30cm depth max., and blow the compressed air of the pressure specified in Table 2 for 30 seconds. Connector shall be monitored for leakage of air during compressive loading. Wire Insulation Adhesive Masking Soldered Conductor End Fig.4 Initial Final 49kPa 29.4kPa Table 2 Rev C2 7 of 28

8 Contact Retention Force: Secure a connector assembly on the tensile testing machine, which is filled with crimped contacts with 0.85mm 2 or larger wires, and apply an axial load to the end of crimped wire by operating the head to travel with the speed at a rate of 100mm a minute. Contact retention force is determined when the contact is dislodged from the housing cavity Housing Retention Force: Secure a mated pair of connectors on the tensile testing machine with locking mechanism set in effect, and apply an axial load to separate the connectors to free end side connector by operating the head to travel with the speed at a rate of 100 mm a minute. Housing retention force is determined when the connector halves are separated with or without damage of locking mechanism Heat Resistibility: Mated pair of connectors are subject to thermal exposure in the test oven for 120 hours where the elevated temperature is controlled to maintain at 120. After test duration, connectors are taken out of the oven, and reconditioned in the room temperature before undergoing subsequent measurements Cold Resistibility: Mated pair of connectors are subject to exposure under chilled atmosphere in the test chamber for 120 hours, where the temperature is controlled to maintain at -50 ±5. After test duration, connectors are taken out from the test chamber, and reconditioned in the room temperature before undergoing subsequent measurements Thermal Shock: Mated pair of connectors are subject to exposure under 50 cycles of heat conditioning in the test chamber, each cycle consisting of the temperature changes as specified in Table 3. After conditioning for 100 cycles, reconditioned in the room temperature, before the subsequent measurements. Step Test Conditions ±5, for 1 hour 2 Room Temperature for 5 minutes max ±5, for 1 hour 4 Room Temperature for 5 minutes max. Table 3 Rev C2 8 of 28

9 Kojiri Resistibility: Tightly secure a connector assembly on a sturdy bench and mate a counterpart connector as shown in Fig.5. Kojiri testing is performed by applying a torque force of 196N cm to the mated connector reciprocatingly to force in right-left direction at every depth of 1 mm graduation along the extraction stroke, until the connector halves are completely separated. Making one separation a cycle, repeat insertion and extraction in the same manner for 25 cycles. After completion of 25 cycles in this direction, turn it to a traverse direction, and repeat for another 25 cycles as started. Note: Kojiri is a Japanese term, meaning the motions to give forcing stress to a set of assembled parts as connectors or contacts in mated condition in the manner of twisting, bending and rolling, forcing in the directions amiss to working axis, resulting detrimental affection to the parts involved especially, deformation, breakage and damages as usually seen in contact/ connector applications. The Point where Kojiri force is applied. 5 mm max. Plug Housing Secured Tightly Cap Housing Fig Salt Spray: Hang a mated pair of connectors in a closed test chamber, where the connectors are subject to exposure under salt spray of 5 ±1% in solution, in specific gravity and in hydrogen exponent, misted over the sample connectors by the aid of compressed air pressure of kPa in the temperature of 80 ±5 in relative humidity of 90-95% for 96 hours. After completion of exposure duration, dry in the room temperature before subsequent measurements. During the salt spray conditioning, test voltage of 28V must be applied to the circuit shown in Fig.3. Rev C2 9 of 28

10 Vibration High Frequency: After having all the contacts series-wired, mate the connector halves and secure on the vibration testing machine as shown in Fig.6. The sample connectors are subject to the vibration of 44m/s 2 (4.5G) in sweeping frequencies changing between Hz reciprocating one cycle a minute. During the vibratile conditioning, the circuits shall be energized with test current of 1 A at open circuit voltage of 12 V DC. Test for 8 hours, and the connector circuit shall be monitored for electrical discontinuity greater than 1 microsecond taking place in the circuit. Direction of Vibration Connector Wires Tightly Secured 150 mm Approx. Vibration Table Fig Vibration Low Frequency: After having all the contacts series-wired, mate the connector halves and secure on the vibration testing machine conforming to SAE J 577 as shown in Fig.6. The sample connectors are subject to vibration produced by power driven cam drops with the stroke of 3.2mm operated at a rate of 12.5Hz. The end of vibration plate shall be suspended by the spring tension of N. During the testing for 1 hour, the circuit is energized with test current of 1 A at open circuit voltage of 12 V, and monitored for electrical discontinuity greater than 1 μ sec taking place in the circuit Water Sprinkle: Mated pair of connectors are tested in the test chamber after hanging and heated to 120±3 or 40 minutes, by sprinkling water at room temperature over the sample for 20 minutes. Making the stated steps one cycle, repeat testing for 48 cycles. Water sprinkling condition must be in accordance with JIS D 0203, Method SI. For this test, wires longer than 2 meters are used for termination, and the ends of which must be watertight-finished by soldering and adhesive material as started in Para , and kept outside the test chamber. During the test, test potential of 28V DC shall be applied between the probing points. The circuit shall be monitored for current leakage taking place in the circuit. Rev C2 10 of 28

11 Current Cycling: Mated pair of connectors are subject to testing by applying test current calculated by Tables 4 for 200 cycles, each cycle consisting of energizing for 45 minutes followed by deenergized 15 minutes. This test shall be performed in a draft-free test chamber. Wire Size (mm 2 ) Test Current (DC A) No. of Positions Decreasing Coefficient & Over 0.4 Tables 4 Note: Test current intensity is obtained by test current of corresponding wire size used multiplied by the decreasing coefficient of the number of energized positions Liquid Detergent Resistibility: Mated connector assemblies are subject for testing by immersing in commercially suppliable car washer liquid detergent at 50 ±2 for 1 hour. After the duration, rinse in tap water for 5 minute, and dry in the room temperature before subsequent measurements Oil Resistibility: Mated pair of connectors are subject for testing by immersing in the specified kinds of oil in accordance with the procedure specified in Table 5. Step Procedure 1 Immerse in engine oil for 1 hour. (SAE 10 W) 2 Cleanse in kerosene for 5 minutes. 3 Immerse in Gasoline for 1 hour. (JIS 2202) 4 Dry in room temperature. Table 5 Rev C2 11 of 28

12 Ozon Aging: Mated pair of connectors assemblies are subject for testing in the test chamber, where the sample is hung and exposed under ozon atmosphere with the density of 50±5 ppm at 40 ±2 for 24 hours in accordance with Para. 16 of JIS K After test duration, the sample is taken out of the chamber, and reconditioned in the room temperature. The tested results shall be recorded in accordance with Para of JIS K 6301, pertaining to the cracking condition of rubber sealing Weather Aging: Mated pair of connectors assemblies are subject for testing in accordance with Para. 5.4 (WAN-1S(H) of JIS D 0205, by exposing under the sunshine carbon arc weather aging testing lights at 63 ±3 for 150 hours. The tested results shall be recorded in accordance with Para of JIS K 6301, pertaining to the cracking condition of rubber sealing. Rev C2 12 of 28

13 7.3. Test Sequence All the tests shall be performed in accordance with the test sequence specified in Table 6. (The numbers in the columns indicate the sequence of the tests performed) *Measured current leakage. Classification Sample Groups Test Items Contact Test Sequence Connector Samples I II III IV V VI VII VIII IX X Appearance Insertion Force (Contact/Connector) Extraction Force (Contact/Connector) Termination Resistance Low Level Termination Resistance Watertight Capability Insulation Resistance Handling Touch at Assembly Contact Retention Force Housing Retention Force Heat Resistibility 6 Cold Resistibility 8 Thermal Shock 4 11 Water Sprinkle 2 Current Leakage 7 *3 Kojiri Resistibility 4 Vibration, Low Frequency Vibration, High Frequency Current Cycling 8 Salt Spray 6 Crimp Tensile Strength 2 Liquid Detergent Resistibility Oil Resistibility 7 Ozon Aging 4 Weather Aging Rev C2 13 of 28

14 8. QUALITY ASSURANCE PROVISIONS: 8.1. Test Conditions: Unless otherwise specified, all the tests shall be performed in any combination of the following test conditions. Temperature Relative Humidity 45-75% Atmospheric Pressure kPa ( mmHg) 8.2. Sample Preparation: Samples: The samples to be employed for the tests shall be prepared in accordance with , TE Application Specification, Crimping Locking Arm Connector Contacts, by using the wires specified in Table 7. No sample shall be reused, unless otherwise specified Number of Samples: The number of contact and connector samples shall be consisting of more than 10 pieces contacts for testing contact, and more than 2 sets of connectors for testing connector. Wire Size mm 2 (AWG) Wire Standard Composition Strand Diameter Number of (mm) Strands Cross-sectional Area mm 2 CMA 0.5 (#20) , (#18) , (#16) , (#14) ,128 Applicable Specification JIS C 3406 Low Voltage Cables for Automobiles Table 7 9. SPECIAL INSTRUCTIONS FOR HANDLING: 9.1. Crimping and Assembly Processing: In order to maintain reliable terminating performance of contacts and housing, crimping contact shall be performed in accordance with , TE Application Specification, Crimping Locking Arm Connector Contacts Assembly of Connector: Insertion of contacts into rubber plug, and rubber plug into housing shall be performed carefully in accordance with customer manual CM-101J, ECONOSEAL* Series J Connector. Care must be taken not to let dust and foreign particles enter around O ring inside the connector. Rev C2 14 of 28

15 9.3. Insertion/Extraction Tool: TE specified, applicable insertion and extraction tools must be used when to insert contact into rubber plug, and/or connector housing. Insertion Tool Instruction Sheet IS-100J Extraction Tool Instruction Sheet IS-081J 10. REFERENCE DOCUMENTS: JASO D 605 JASO D 7101 JIS C 3406 JIS D 0203 JIS D 0204 JIS D 1601 JIS D 0205 JIS K 6301 Automotive Multi-Pole Connectors Test Methods for Molded Plastic Parts Low Voltage Cables for Automobiles Method of Moisture, Rain and Spray Test for Automobile Parts Method of High and Low Temperature Test for Automobile Parts Vibration Testing Method for Electronic Components General Rules of Weatherability for Automobile Testing Physical Testing Methods for Vulcanized Rubber Rev C2 15 of 28

16 1. 適用範 規格 タ コ ト ジ パン ( 合 ) 製造さ コ J コネ タ い 規定 2. 製品型番及び 称 NBR タ 酸含有 型番 う 栓 NBR タ 酸 φ ン ン 称 2φ ン タ ン ッ ン O ン 極用 ム栓 極用 ム栓 極用 ム栓 極用 ム栓 極用 ム栓 極用 ム栓 極 ハウジン 極 ッ ハウジン 極 ハウジン 極 ッ ハウジン 極 ハウジン 極 ッ ハウジン 極 ハウジン 極 ッ ハウジン 極 ハウジン 極 ッ ハウジン 極 ハウジン 極 ッ ハウジン 注記 : 型番 ト中 親番 ッ 付 1 桁 数字 構成さ ま 各親番号 対 ッ 付 番号 細 顧客用 面また タ 参照 さい 接頭 数字 場合 及び ッ 省略さ ま Rev C2 16 of 28

17 3. 用語 説明 規格 適用 用語 意味 通 3.1 コンタ ト : コネ タ 構成部品 あ 接触子 いう こ ンコンタ ト タ コンタ ト あ 3.2 ハウジン : コネ タ 構成部品 あ コンタ ト 収容 いう こ ンコンタ ト 収容 ッ ハウジン タ コンタ ト 収容 ハウジン あ 3.3 ム栓 : 防水性 得 目的 ハウジン 及び ッ ハウジン 電線側 挿入さ いう 3.4 う 栓 : 2 極以 コネ タ 場合 コンタ ト 使用 い極数 ム栓穴 う 込 使用 いう 3.5 O ン : ッ ハウジン 装着さ ハウジン 嵌合 た時 両者 間 防水性 得 目的 使用さ いう 3.6 コネ タ : 電線 圧着 たコンタ ト ム栓 通 ハウジン 全極 ッ ン た いう こ ンコンタ ト ッ ハウジン ム栓及び O ン ッ ン た タ コンタ ト ハウジン 及び ム栓 ッ ン た あ 4. 使用材料 表面処理 4.1 コンタ ト : ASTM B 36 COPPER ALLOY 260 準拠 錫 付黄銅条件 製造さ 4.2 ハウジン : 耐熱 66 ン樹脂 製造さ 4.3 う 栓 : 耐熱 66 ン樹脂 製造さ 4.4 ム栓 : ン ム (CR) 製造さ 4.5 O ン : ト ム NBR 製造さ 5. 形状 構造及び寸法 5.1 コンタ ト : 形状 構造及び寸法 当 面 合致 い こ ンコンタ ト タ コンタ ト 適用電線範 関係 く相互 嵌合 5.2 ハウジン : 形状 構造及び寸法 当 面 合致 い こ 誤嵌合防 機構 ハウジン 相互 ッ 機構及びコンタ ト挿入 有 5.3 う 栓 : 形状 構造及び寸法 当 面 合致 い こ 全 極数 ム栓 適用 5.4 ム栓 : 形状 構造及び寸法 当 面 合致 い こ コンタ ト 挿入方向マ ハウジン 置合わ 矢印 製品 マ 有 5.5 O ン : 形状 構造及び寸法 当 面 合致 い こ Rev C2 17 of 28

18 6. 使用条件 6.1. 使用温度範 30~105 周 温度 通電 温度 昇 6.2. 適用電線範 型番適用電線範 mm 2 絶縁被覆外径 , 0.85, 1.25, 2 1 圧着 2.0~3.4 mm 圧着 2.0~2.8 mm 7. 性能及び試験方法 7.1. 性能 第 7.2 試験方法 及び第 7.3 試験 序 基 試験 た結果 第 1 表 性能 足 こ Rev C2 18 of 28

19 第 1 表 目 試験コンタ ト 性能コネ タ 性能方法初期性能初期性能耐久 環境試験後 性能 外観 亀裂 割損 破損 た 部品 錆び 溶解等 機能 損う いこ コンタ ト又 極数 N コネ タ挿入力 N 以 コンタ ト又 極数 N コネ タ引抜力 N 以 ベ 抵抗 mΩ 以 10mΩ 以 総合抵抗 mV/A 以 10mV/A 以 絶縁抵抗 MΩ 以 電流 μ A 以 挿抜 ン 有害 引掛 等 いこ 0.5mm N 以 圧着部引張強度 mm 2 127N 以 1.25mm 2 177N 以 2.0mm 2 265N 以 性 kpa 以 29.4kpa 以 コンタ ト保持力 N 以 ハウジン 保持力 N 以 耐熱性 耐寒性 熱衝撃 耐こ 性 散水 高周波振動 耐衝撃性 塩水噴霧 電流 耐洗剤液 耐油 耐 ン 耐候性 第 5 表 示 序 耐久 環境試験 行 た 性能 足 こ Rev C2 19 of 28

20 7.2. 試験方法 外観 外観 目視及び感触 観察 有害 亀裂 割損 た 部品 錆 溶解及び変形等 有無 確認 コンタ ト又 コネ タ 挿入力 コンタ ト又 コネ タ 一方 固定 他方 軸方向 毎分約 100mm 一定速度 操作 ハウジン ッ 機構 作用さ 行う コンタ ト又 コネ タ引抜力 コンタ ト又 コネ タ 一方 固定 他方 軸方向 毎分約 100mm 一定速度 操作 ハウジン ッ 機構 作用さ 行う ベ 抵抗コンタ ト又 コネ タ 嵌合 た状態 開放電圧 DC50mV 以 短絡電流 50mA 以 通電 圧着部 75mm 離 た 抵抗 測定 第 1 Y Y 間 ベ 抵抗 Y Y 間 抵抗 150mm 電線 抵抗分 差引い 算出 測定 1 極 行う 第 1 Rev C2 20 of 28

21 7.2.5 総合抵抗コンタ ト又 コネ タ 嵌合 た状態 開放電圧 DC12V 短絡電流 1A 通電 コンタ ト 温度 安定 た後 圧着部 75mm 離 た 電圧降 測定 第 1 Y Y 間 総合抵抗 Y Y 間 電圧降 150mm 電線 電圧降 差引い 算出 測定 1 極 行う Y Y 被覆 余分 電流密度 一様 た あ 電線部分 半田 絶縁抵抗コネ タ 嵌合 た状態 第 2 如く隣接 コンタ ト相互間 及びコンタ ト対ハウジン 間 対 間 測定 測定電圧 DC500V 第 2 測定器 コンタ ト相互間 測定器 コンタ ト対ハウジン 間 電流 コネ タ 嵌合 た状態 第 3 如く隣接 コンタ ト相互間 DC28V 印加 第 3 Rev C2 21 of 28

22 7.2.8 挿抜 ン コンタ ト又 コネ タ 挿入 引抜 手動 行い そ ン 触感 確認 圧着部引張強度 約 100mm 長さ 電線 圧着 たコンタ ト 固定 電線 軸方向 毎分約 100mm 一定速度 引張 電線 破断又 圧着部 電線 引抜けた時 荷重 測定 性コネ タ ハウジン 穴 あけ そ 穴 圧縮空気 送 コネ タ 性 調 試験 あた 電線 先端 ハン 付後接着剤 密封 [ 第 4 ] 測定 コネ タ 水中 水面 30cm 以内 入 [ 第 2 表 ] 示 圧縮空気 30 秒間送 空気 い う 調 第 4 電線 接着剤 第 2 表 目 初期 耐久 環境試験後 空気圧 kpa 49kPa 29.4kPa コンタ ト保持力ハウジン 約 100mm 長さ 0.85mm 2 以 断面積 電線 圧着 コンタ ト 組込ま たコネ タ 固定 電線 軸方向 毎分約 100mm 一定速度 引張 コンタ ト ハウジン 抜けた時 荷重 測定 ハウジン 保持力 コネ タ 嵌合 ッ 機構 作用 た状態 一方 固定 他方 軸方向 毎分約 100mm 一定速度 引張 ッ 機構外 又 破損 嵌合 外 た時 荷重 測定 Rev C2 22 of 28

23 耐熱性コネ タ 嵌合 た状態 120±3 保た た恒温槽 24 時間放置 そ 後取 出 常温 戻 ま 放置 耐寒性コネ タ 嵌合 た状態 50±5 保た た恒温槽 24 時間放置 そ 後取 出 常温 戻 ま 放置 熱衝撃コネ タ 嵌合 た状態 第 3 表 示 試験 1 こ 5 行 た後 室温 戻 ま 放置 第 3 表 試験 序 試験方法 1 120±5 1 時間 2 室温 5 分以内 3 50±5 1 時間 4 室温 5 分以内 耐こ 性コネ タ 引抜 時 第 5 如くコネ タ 一方 固定 他方 1mm 間隔 コンタ ト 士 嵌合 外 ま 引抜 各段階 前後方向 1 往復 196N cm T ト 加え こ 1 25 行う 右方向 様 1 往復 196N cm T ト 加え こ 1 25 行う 第 5 Rev C2 23 of 28

24 塩水噴霧密閉タン 内 コネ タ 吊 温度 35±5 塩水濃度 5±1% 比重 ~ PH6.5~7.2 塩水 kPa 圧力 24h 噴霧さ そ 後コネ タ 度槽内 吊 80±5 度 90~95%RH 24h 放置 そ 後常温 乾燥後測定 塩水噴霧中 コネ タ 各極間 第 3 示 回路 28V 電圧 印加 高周波振動コネ タ 嵌合 全極直列 接続 開放電圧 DC12V 短絡電流 1A 通電 た状態 第 6 如く振動試験機 取 付け 振動加速度 44m/s 2 振動周波数 20~200Hz 往復 1 分間 さ こ X,Y 方向各 4 時間計 8 時間行い 1μ sec 以 瞬断 有無 観察 こ 試験 用い 電線 0.85mm 2 以 第 6 振動方向 コネ タ 電線 両端固定 振動台 耐衝撃性コネ タ 嵌合 全極直列 接続 開放電圧 DC12V 短絡電流 1A 通電 た状態 第 6 如く SAE J 577 試験装置 取付け 振動数 12.5Hz ム落 3.2mm 衝撃台 端 ン 張力 N 1 時間行い 1μ sec 以 瞬断 有無 確認 散水試験コネ タ 散水試験槽内 吊 48 時間実施 散水条件 JIS D 0203 SI 試験中 コネ タ 各極間 28V 電圧 印加 電流 記録 試験 実施 ワ 2m そ 端 ハン 付後 接着剤 密封 試験槽 外 出 Rev C2 24 of 28

25 電流 コネ タ 嵌合 た状態 全極 第 4 表 算出さ 電流 通電 通電 45 分間 休 15 分間 行う 試験中 無風状態 行う 第 4 表 電線 mm 2 電流値 DC A 極数減少係数 ~ ~ ~ ~ 以 0.4 注 通電電流 各電線 対応 電流値 極数 対応 減少係数 積 算出さ 耐洗剤液 50±2 ウ ッ 液 市販品 コネ タ 1 時間浸漬 そ 後水道水中 5 分間浸漬 た ち 自然乾燥 行う 耐油性 コネ タ 嵌合 た状態 50±2 ンジン油 SAE10W 又 等品 常温 ン JIS K 2202 又 等品 及び常温 白灯油 使用 序 試験 行う ンジン 1 時間浸漬 白灯油洗浄 5 分間浸漬 ン 1 時間浸漬 自然乾燥 耐 ンコネ タ 嵌合 た状態 40±2 保た た密閉容器内 吊 JIS K 6301 第 16 基 ン濃度 50±5pphm 中 24 時間放置後取 出 室温 放置 ム 亀裂状態 JIS K 6301 第 16.6 基 記録 く 耐候性コネ タ 嵌合 た状態 JIS D 0205 第 5.4 WAN 1S 基 ン ン ボン 灯式耐候性試験機 63±3 150 時間試験 行う ム 亀裂状態 JIS K 6301 第 16.6 基 記録 く Rev C2 25 of 28

26 目 7.3. 試験 序 区 試験 序 第 5 表 示 毎 序 従 行う 分 コンタ ト 第 5 表 試験 序 コネ タ I II III IV V VI VII VIII IX X 外観 コネ タ又 コンタ ト挿入力コネ タ又 コンタ ト引抜力 ベ 抵抗 総合抵抗 性 絶縁抵抗 挿抜 ン コンタ ト保持力 5 ハウジン 保持力 11 高温放置 6 温放置 8 熱衝撃 4 散水 2 電流 7 *3 耐こ 性 4 耐衝撃 3 振動 6 ント 8 塩水噴霧 6 圧着部引張強度 2 耐洗剤液 5 耐油 7 耐 ン 4 耐候性 4 *: 散水中 電流測定 行う Rev C2 26 of 28

27 8. 品質保証条件 8.1. 試験条件 特 指定 い場合 第 6 表 示 環境条件 性能試験 行う 第 6 表 温度 15~35 相対 度 45~75% 気圧 kpa mmHg 8.2. 試験 試料性能試験 用い 試料 取付適用規格 ッ ン ム コネ タ コンタ ト 圧着条件 基 い 第 7 表 示 電線 圧着 た 規 試料 あ こ い 試料 規定さ た 序以外 他 試験 用い い 試料数性能試験 用い 試験数 各 毎 コンタ ト単体 場合 10 ット コネ タ 場合 2 ット以 行う 使用電線性能試験 用い 電線 第 7 表 示 電線 行う 第 7 表 電線 素線構成断面積 呼び AWG 素線径 (mm) 素線数 mm 2 CMA 0.5 # # # # 電線規格 JIS C 3406 自動車用電線 Rev C2 27 of 28

28 9. 取扱い 注意事 9.1. 圧着及び取扱い ハウジン コンタ ト 保持性能及びコネ タ 接触性能 維持 コンタ ト 圧着 ッ ン ム コネ タ端子取付規格 基 い 作業 行うこ 9.2. コネ タ 組立作業 ム栓及びコンタ ト ハウジン 挿入作業 コ J コネ タ取扱説明書 CM 101J 基 い 作業 行うこ く O ン 塵埃 付着 い う 十分注意 こ 9.3. 挿入 具 引抜 具 ム栓 コンタ ト挿入 具及びコンタ ト ハウジン 引抜く場合 引抜 具 TE 指定 具 使用 こ 挿入 具 : 型番 ( 取扱説明書 IS-100J) 引抜 具 : 型番 ( 取扱説明書 IS-081J) 10. 参考規格 JASO D 605 : 自動車用多極コネ タ JASO D 7101 : ッ 成形部品 試験方法 JIS C 3406 : 自動車用 圧電線 JIS D 0203 : 自動車部品 耐 び耐水試験方法 JIS D 0204 : 自動車部品 高温及び 温試験方法 JIS D 1601 : 自動車部品振動試験方法 JIS D 0205 : 自動車部品 耐候性試験通則 JIS K 6301 : 加硫 ム物理試験法 JIS K 2202 : 自動車 ン Rev C2 28 of 28