スレッドミルシリーズ Thread Mill Vol.14 新価格体系 New Price 2018 年 6 月
Index P. 2 Tool Lineup and Guide for Icons P. 3 Total Solutions for Your Thread Milling Needs Solid Type P. 5 Tool Selection Guide by Work Materials P. 6 Tool Selection Guide by Screw Size AT-1 P. 8 One Pass Thread Mill WH-VM-PNC P. 11 for Small Diameter WX-ST-PNC P. 12 for Steels WXO-ST-PNC P. 15 for Steels with Internal Coolant Supply WX-PNC P. 16 for Nonferrous Metal and Heat-Resistant Alloy OT-SFT-PNGT P. 19 for General Purpose, Solid Carbide Spiral-Fluted Type OT-PNGT P. 20 for General Purpose, Solid Carbide Type PNGT P. 22 for HSS DR-PNAC P. 24 Super-Planet Cutter for Multifunction Milling DR-O-PNAC P. 24 Super Planet Cutter for Multifunction Milling with Internal Coolant Supply Indexable Thread Mill (HY-PRO P) P. 25 Guide for Selecting HYPRO-P P. 27 Tool Selection Guide by Screw Size HY-PRO P P. 35 Multi-Point HY-PRO P P. 48 Single Point P. 51 Tips for Machining and Recommended Cutting Conditions P. 56 Machining Data P. 67 Features of Thread Mills and Hints for Usage P. 69 FAQ about Thread Milling Go to the following for the quick tool search! Search for suitable tools from specific materials P.5 Tool Selection Guide by Work Materials (p.5) Search for suitable tools from specific screw sizes P.6 Solid Type (p.6) P.27 HY-PRO P (p.27)
IndexRecommended Tools Solid types, by application WX-ST-PNC / WXO-ST-PNC for Steels WX-PNC for Nonferrous Metals and Heat-Resistant Alloy Suitable for carbon, stainless and hardened steels (up to 45HRC) With/without coolant hole Suitable for non-ferrous metals and heat-resistant alloys WH-VM-PNC for Small Diameter Suitable down to M1, 0.25 pitch small-diameter threads Suitable for carbon steels, stainless steels, castings and non-ferrous metals Indexable Thread Mill (HY-PRO P) Multi-Point Single Point For detailed information on indexable thread mills (HY-PRO Planet Cutters), see p. 26. Guide for Icons 1 Tool Materials 2 Helix Angle 3 Shank Tungsten Carbide Cobalt HSS 911 Helix angle of flute for cutters Tolerance for shank diameter 4 EgiAs Surface Treatment EgiAs Coating WX WX Super coating 5 Page References 6 Thread Type Indicates page no. for recommended conditions. for Internal Thread Smooth coating FX TiAIN FX (composite multi-layered TiAIN) coating Indicates page no. for attachable bodys. for External Thread WX TiAIN WX (TiAIN) coating TiCN TiCN coating Indicates page no. for attachable inserts. TiN TiN coating Planet Cutter is registered trademark of OSG Corporation.
3 Support Tools for Your Thread Milling Needs Reduce setup, machining time, and achieve stable tool life with these 3 support tools. 2 ThreadPro Thread Milling NC Code Generator Software 1 RPRG Reference value of tool radius offset Thread Milling 3 Diameter Correction Tool for Thread Mills Use RPRG to reduce the workload RPRG is the reference value of tool radius offset Conventionally, the tool radius was entered during setup as a parameter of the NC system, which was corrected by checking the thread with a gauge. However, it has become possible to reduce the checking and correction simply by entering the RPRG value indicated on the tool shank. ISO-5H Internal Thread ISO-6H Internal Thread Example Tool diameter:7.5; Pitch: 1; Minimum cutting bore diameter: M10 (EDP No.:8304721) Internal thread size: M10 1 Tolerance for pitch diameter: 0 to +0.118 (ISO-5H), 0 to +0.150 (ISO-6H) Entered value of RPRG: 3.681 Pitch Dia. Radius RPRG=3.681 Entered value of Radius: 3.75 Notes 1. RPRG are reference values. Optimal values for actual cutting depend on the machining environment. Determine optimal values after trial cutting. 2. RPRG values are optimally established to achieve ISO:5H (formerly Grade 1) internal thread limits for metric threads and ANSI:3B internal thread limits for unified threads. RPRG values established for taper pipes (R/Rc) are effective when using the thread milling NC code generator software ThreadPro available on our website. 3. For diameters of thread mills, RPRG values are calculated based on the minimum cutting bore diameter (the minimum cutting internal thread size of the tool diameter). To cut other diameters, it is necessary to use a smaller value than RPRG. 4. RPRG values are indicated on tools manufactured from November 2014.
Revamped Thread Milling NC Code Generator Software "ThreadPro" Generate codes for complex machining couldn't be easier. Create machining programs at ease with OSG's revamped NC code generator software ThreadPro. Supporting Tools3 Key Revamped Features Available in 12 different languages Supports 8 NC programming languages Calculates the most appropriate RPRG value ThreadPro with Comprehensive Features 1) Generate programs for zero cut at ease 2) High quality machining by stair passes 3) Capability to review machining trajectory to reduce tool damage Pass type : continuous Pass type : stairs Achieve Stable Tool Life with the DCT for Accurate Diameter Measurement The internal thread effective diameter, which used to be difficult to determine, can now be measured with readable values. Please refer DCT catalogue for details. How can we properly determine the diameter correction value? When the effective diameter of the limit gauge is minus, the radius correction value of the thread mill cannot be determined. However, with the use of the thread mill Diameter Correction Tool (DCT), the effective diameter can be measured, which can eliminate the risk of hole expansion, allow appropriate adjustment and significantly reduce setup time. Is the internal thread effective diameter always the same after changing tool? Knowing the internal thread effective diameter value can help maintain the same effective diameter after exchanging tool. As long as the starting position is the same, the GO position (tool life) can be aligned to help predict and stabilize tool life.
Tool Selection Guide by Work Materials Best Good Solid Type Indexable Thread Mill Type One Pass Thread Mill for Small Dia. for Steels for Steels with Internal Coolant Supply M1 M1.8 M2 for Nonferrous Metal and Heat- Resistant Alloy Multi-Point Single-Point Product AT-1 WH-VM-PNC WX-ST-PNC WXO-ST-PNC WX-PNC HY-PRO P HY-PRO P Low Carbon SteelMild Steel Medium Carbon Steel High Carbon Steel Alloy Steel C0.25% C 0.25 0.45% C0.45% SCM 25 45HRC Hardened Steel 45 50HRC 50 60HRC Work Material Stainless Steel Tool Steel Cast Steel Cast Iron Ductile Cast Iron Copper Brass Brass Casting Bronze Aluminum Rolled Steel Aluminum Alloy Casting Magnesium Alloy Casting Zinc Alloy Casting Titanium Alloy N i Nickel Alloy Thermo Setting Plastic Thermo Plastic Page P.8 P.11 P.12 P.15 P.16 P.35 P.48SUS304 SUS420 SKD SC FC FCD Cu Bs BsC PB Al AC, ADC MC ZDC Ti-6Al-4V Inconel - - Machining program may need adjustment of cutting speed and depth.
Selection Guide by Screw Size Tool Metric screw thread (internal) Pitch Page P.8 P.11 P.12 P.15 P.16 P.19 P.20 P.22 Min. Cutting Bore Dia. AT-1 WH-VM-PNC WX-ST-PNC WXO-ST-PNC WX-PNC OT-SFT-PNGT OT-PNGT PNGT One Pass Thread Mill Small Dia. P0.25 M 1 3900495 M 1.2 3900496 P0.3 M 1.4 3900497 P0.35 M 1.6 3900498 M 1.7 3900499 P0.4 M 2 3900500 P0.45 M 2.5 3900501 for Steel for Steel with Internal Coolant Supply for Nonferrous Metal Heat-Resistant Alloy M 3 3900502 P0.5 M 8 8331002 8304710 3900009 M 14 8331012 8305736 8304740 3900036 P0.7 M 4 3900503 M 6 8331000 8305700 8304700 3900000 P0.75 M 14 8331013 8305741 8304741 3900041 P0.8 M 5 3900504 General Purpose Spiral General Purpose M 6 8331001 8304701 3900001 8306501 M 8 8331003 8304711 3900011 M 10 8331005 8304721 3900021 M 12 8331008 P1.0 M 14 8331014 8305742 8304742 3900042 8306542 8306241 8306012 M 16 8331017 8305752 8304752 3900052 8306022 M 20 8306032 M 27 8306042 M 34 8306052 M 8 8331004 8304712 3900012 P1.25 M 10 8331006 M 12 8331009 8305732 8304732 3900032 8306532 8306232 M 10 8331007 8304723 3900023 M 12 8331010 8305733 8304733 3900033 M 14 8331015 8304743 3900043 8306543 8306013 M 16 8331018 8304753 3900053 8306023 P1.5 M 20 8331021 8304773 3900073 8306273 8306033 M 24 8331023 8304783 M 27 3900083 8306583 8306043 M 34 8306053 M 42 8306063 P1.75 M 12 8331011 8305734 8304734 3900034 8306534 8306234 M 14 8331016 8305744 8304744 3900044 8306544 8306245 M 16 8331019 8304754 3900054 8306554 8306024 M 20 8306034 P2.0 M 24 8331024 8305784 8304784 M 27 3900084 8306584 8306285 8306044 M 34 8306054 M 42 8306064 P2.5 M 18 8331020 8305765 3900065 M 20 8331022 8305775 8304775 3900075 8306575 8306276 8306035 M 20 8306036 M 24 8331025 8305786 8304786 P3.0 M 27 3900086 8306586 8306287 8306046 M 34 8306056 M 42 8306066 P3.5 M 27 8306047 HSS Tool Selection Guide by Screw SizeTool Selection Guide by Work MaterialsNEXT
Tool Selection Guide by Screw Size Unified screw thread (internal) T.P.I. 32 28 24 20 18 16 Page P.9 P.11 P.13 P.17 Min. Cutting Bore Dia. AT-1 WH-VM-PNC WX-ST-PNC WX-PNC No.8 3900513 5 16 8331030 3 8 8331033 1 4 8331027 8305801 3900351 1 2 8331038 5 16 8331029 8305806 3900356 3 8 8331032 8305811 3900361 5 8 8331043 1 4 8331026 8305800 3900350 7 16 8331035 8305816 3900366 1 2 8331037 8305821 3900371 1 8331049 5 16 8331028 8305805 3900355 9 16 8331040 8305830 3900380 5 8 8331042 3 8 8331031 8305810 3900360 3 4 8331045 7 16 8331034 8305815 3900365 14 7 8 8331047 13 1 2 8331036 8305820 3900370 12 9 16 8331039 8305825 3900375 7 8 8305840 3900390 11 5 8 8331041 8305832 3900382 10 3 4 8331044 8305835 3900385 9 7 8 8331046 8305838 3900388 8 1 8331048 8305842 3900392 Pipe screw thread T.P.I. 28 19 14 11 Page P.10 P.14 P.18 P.21 P.23 Range of Thread Size AT-1 WX-ST-PNC WX-PNC OT-PNGT PNGT 1 16 8331075 3900199 1 8 8331075, 8331076 3900199, 3900201 1 4 8331077 3900211 3 8 8331077, 8331078 8305912 3900211, 3900212 8306310 8306111 ½ 8331079 3900214 8306114 3 4 8331079, 8331080 8305915 3900214, 3900215 8306316 8306114, 8306115 1 8306118 1 1 4 8306118 1 1 2 2 8331081 3900218 8306320 8306118, 8306119 8306118, 8306119 Pipe screw thread Rp(PS)G(PF) Rp(PS) G(PF) Page P.10 P.14 P.18 P.21 P.23 T.P.I. 28 19 14 11 Range of Thread Size AT-1 WX-ST-PNC WX-PNC OT-PNGT PNGT 1 16 8331082 8305949 3900299 1 8 8331082, 8331083 8305949, 8305951 3900299, 3900301 1 4 8331084 8305961 3900311 3 8 8331084, 8331085 8305961, 8305962 3900311, 3900312 8306410 8306121 8306131 ½ 8331086 8305964 3900314 8306124 8306134 5 8 8331086 8305964 3900314 8306124 8306134 ¾ 7 8 8331086, 8331087 8331086, 8331087 8305964, 8305965 8305964, 8305965 3900314, 3900315 3900314, 3900315 8306416 8306416 8306124, 8306125 8306124, 8306125 8306134, 8306135 8306134, 8306135 1 8306128 8306138 1 1 8 8306128 8306138 1 1 4 8306128 8306138 1 ½ 1 ¾ 2 8331088 8305968 3900318 8306420 8306128, 8306129 8306128, 8306129 8306128, 8306129 8306138, 8306139 8306138, 8306139 8306138, 8306139 Pipe screw thread T.P.I. 27 18 14 11½ Page P.10 P.14 P.18 Range of Thread Size 1 1 16 8331089 1 8 AT-1 WX-ST-PNC WX-PNC 8331089, 8331090 1 4 8331091 3 8 ½ ¾ 1 1 4 1 ½ 2 8331091, 8331092 8305859 3900259 8305861 3900261 8331093 8305865 3900265 8331094 8305868 3900268
Tool Selection Guide by Screw Size One Pass Thread Mill AT-1 Type 1 Type 2 EgiAs 911 Pitch P51 Dc L n Ds Flutes Type Unit:mm Yen 8331000 0.75 13.5 31,800 M 6 4.5 75 16 6 4 1 8331001 1 14 31,800 8331002 0.5 17 31,800 8331003 M 8 1 5.7 75 18 6 4 2 31,800 8331004 1.25 18.75 31,800 8331005 1 22 36,100 8331006 M10 1.25 7.7 85 22.5 8 4 2 36,100 8331007 1.5 24 36,100 8331008 1 26 40,400 8331009 1.25 27.5 40,400 M12 9.7 100 10 5 2 8331010 1.5 27 40,400 8331011 1.75 28 40,400 8331012 0.5 29 59,600 B 8331013 0.75 11.7 2 59,600 120 30 12 8331014 M14 1 5 59,600 8331015 1.5 10.7 31.5 34.5 1 59,600 8331016 2 9.7 100 32 10 2 40,400 8331017 1 34 72,200 13.7 135 39 16 1 8331018 M16 1.5 5 72,200 36 8331019 2 11.7 120 12 2 59,600 8331020 M18 2.5 11.7 120 42.5 12 5 2 59,600 8331021 1.5 15.7 43.5 2 76,400 M20 135 16 5 8331022 2.5 13.7 45 50 1 72,200 8331023 1.5 51 87,100 8331024 M24 2 19.7 150 52 20 6 2 87,100 8331025 3 54 87,100 B=Standard stock item AT-1 (M) is only for milling internal threads. See p.2 for explanation of icons. Please select"multi-feed" for the path type in ThreadPro. Solid Type
One Pass Thread Mill AT-1 Type 1 Type 2 EgiAs 911 P51 No. EDP No. Min. Cutting Bore Dia. T.P.I. Dc L n Ds Flutes Type Unit:mm Yen 8331026 20 15.24 17.78 32,700 1 4 4.55 75 6 4 1 8331027 28 15.42 17.23 32,700 8331028 18 19.75 32,700 8331029 5 16 24 5.7 75 19.04 6 4 2 32,700 8331030 32 17.47 32,700 8331031 16 22.23 25.41 32,700 8331032 3 8 24 6.7 85 22.22 24.33 8 4 1 32,700 8331033 32 20.64 22.23 32,700 8331034 14 27.21 32,700 7 16 7.7 85 8 4 2 8331035 20 25.40 32,700 8331036 13 29.31 33.22 37,200 8331037 1 2 20 8.7 100 27.94 30.48 10 5 1 37,200 B 8331038 28 28.12 29.93 37,200 8331039 12 33.87 37,200 9 16 9.7 100 10 5 2 8331040 18 32.45 37,200 8331041 11 36.94 41.56 61,500 8331042 5 8 18 10.7 120 35.28 38.10 12 5 1 61,500 8331043 24 34.91 37.03 61,500 8331044 10 43.18 61,500 3 4 11.7 120 12 5 2 8331045 16 41.29 61,500 8331046 9 50.80 56.44 80,800 7 8 13.7 135 16 5 1 8331047 14 48.98 52.61 80,800 8331048 8 57.15 63.50 95,800 1 18.7 150 20 6 1 8331049 20 53.34 55.88 95,800 Available from Spring 2019 B=Standard stock item AT-1 (UUNJ) is only for milling internal threads. See p.2 for explanation of icons. Please select"multi-feed" for the path type in ThreadPro.
One Pass Thread Mill AT-1 Type 1 Type 2 Type 3 Type 4 EgiAs 911 P51 No. EDP No. Range of Thread SizeDia. T.P.I. Dc L n Ds 8331075 1 161 8 28 5.67 60 9.1 6 4 4 Flutes Type Unit:mm Yen 35,000 8331076 1 8 28 7.67 60 9.1 12.7 8 4 3 39,500 8331077 1 43 8 19 9.67 75 14.7 10 5 4 44,300 8331078 3 8 19 11.67 85 14.7 20 12 5 3 B 46,000 8331079 1 23 4 14 11.67 85 20 12 5 4 65,000 8331080 3 4 14 15.67 95 20 16 5 4 95,800 8331081 1 2 11 19.67 105 27.7 20 6 4 109,000 Solid Type B=Standard stock item See p.2 for explanation of icons. Please select"multi-feed" for the path type in ThreadPro. No. EDP No. Range of Thread SizeDia. T.P.I. Dc L n Ds Flutes Type Unit:mm Yen 8331082 1 161 8 28 5.67 60 11.8 6 4 31,800 8331083 1 8 28 7.67 65 14.5 8 4 35,800 8331084 1 43 8 19 9.67 80 20.1 10 5 37,700 8331085 3 8 19 11.67 100 25.4 12 5 2 B 39,500 8331086 1 2 7 8 14 11.67 100 32.7 12 5 59,100 8331087 3 47 8 14 15.67 115 39.9 16 5 78,600 8331088 1 2 11 19.67 130 50.8 20 6 103,000 No. EDP No. Range of Thread SizeDia. T.P.I. Dc Available from Spring 2019 L B=Standard stock item See p.2 for explanation of icons. Please select"multi-feed" for the path type in ThreadPro. Available from Spring 2019 n Ds Flutes Type Unit:mm Yen 8331089 1 161 8 27 5.67 60 10.35 6 4 35,000 8331090 1 8 27 7.67 60 10.35 8 4 35,000 8331091 1 43 8 18 9.67 75 15.52 10 5 4 44,300 B 8331092 3 8 18 11.67 85 15.52 12 5 69,100 8331093 1 23 4 14 15.67 95 19.96 16 5 82,400 8331094 12 11½ 18.72 105 24.3 28.7 20 6 3 109,000 B=Standard stock item See p.2 for explanation of icons. Please select"multi-feed" for the path type in ThreadPro.
for Small Diameter WH-VM-PNC S11.4 M11.8 M25 No.8 SS Dc1.3 or WXS 1.5Dc 11 SHANK h6 P53P54 No. EDP No. Min. Cutting Bore Dia. Pitch Dc L Thread Per Cutting Part n Ds Flutes Yen 3900495 S1 0.25 0.72 40 0.25 1 2.75 3 3 10,400 3900496 S1.2 0.25 0.91 40 0.25 1 3.25 3 3 B 10,400 3900497 S1.4 0.3 1.05 40 0.3 1 3.8 3 3 10,400 No. EDP No. Min. Cutting Bore Dia. Pitch Dc L Thread Per Cutting Part n Ds Flutes Yen 3900495 M1 0.25 0.72 40 0.25 1 2.75 3 3 10,400 3900496 M1.2 0.25 0.91 40 0.25 1 3.25 3 3 10,400 3900497 M1.4 0.3 1.05 40 0.3 1 3.8 3 3 10,400 3900498 M1.6 0.35 1.2 40 0.35 1 4.35 3 3 10,400 3900499 M1.7 0.35 1.3 40 0.35 1 4.85 3 3 10,400 B 3900500 M2 0.4 1.5 40 1.2 3 4.4 6 3 24,000 3900501 M2.5 0.45 1.9 40 1.4 3 5.6 6 3 24,000 3900502 M3 0.5 2.4 40 1.5 3 6.5 6 3 24,000 3900503 M4 0.7 3.1 40 2.1 3 8.7 6 3 24,000 3900504 M5 0.8 4 40 2.4 3 10.8 6 3 24,000 No. EDP No. Min. Cutting Bore Dia. T.P.I. Dc L Thread Per Cutting Part n Ds Flutes Yen 3900513 No.8 32 3.2 40 2.4 3 9.1 6 3 B 24,000 Unit:mm B=Standard stock item Unit:mm B=Standard stock item Unit:mm B=Standard stock item See p.2 for explanation of icons. WH-VM-PNC (S, M, UUNJ) is only for milling internal threads. Please select"multi-feed" for the path type in ThreadPro.
for Steels WX-ST-PNC Type 1 Type 2 11 P51 No. EDP No. Min. Cutting Bore Dia. Pitch Dc L n Ds 8305700 M 6 0.75 4.5 60 12.8 15 6 4 1 Flutes Type Unit:mm Yen 31,800 8305732 1.25 26.3 40,400 8305733 M12 1.5 9.5 85 25.5 28 10 5 1 40,400 8305734 1.75 26.3 40,400 8305736 0.5 28.5 40,400 8305741 0.75 29.3 40,400 M14 10 85 10 5 2 8305742 1 29 C 40,400 8305744 2 30 40,400 8305752 M16 1 12 95 33 12 5 2 59,600 8305765 M18 2.5 14 105 40 45 16 5 1 72,200 8305775 M20 2.5 16 105 42.5 16 5 2 78,700 8305784 2 50 103,000 M24 20 120 20 6 2 8305786 3 51 103,000 Solid Type C=Standard stock item See p.2 for explanation of icons. WX-ST-PNC (M) is only for milling internal threads. Please select"multi-feed" for the path type in ThreadPro. The products have been stopped producing and replaced by AT-1 p.8.
for Steels WX-ST-PNC Type 1 Type 2 11 P51 No. EDP No. Min. Cutting Bore Dia. T.P.I. Dc L n Ds Flutes Type Unit:mm Yen 8305800 20 10.2 11.4 32,700 1 4 4.55 60 6 4 1 8305801 28 10 10.9 32,700 8305805 18 32,700 5 16 6.2 65 12.7 14.1 8 4 1 8305806 24 32,700 8305810 16 14.3 32,700 3 8 7.6 65 8 4 2 8305811 24 14.8 32,700 8305815 14 18.1 19.9 37,200 7 16 8.8 75 10 4 1 8305816 20 17.8 19.1 37,200 8305820 13 19.5 21.5 C 37,200 1 2 9.4 75 10 5 1 8305821 20 19.1 20.4 37,200 8305825 12 10.9 23.3 25.4 61,500 9 16 85 12 5 1 8305830 18 11.4 22.6 24 61,500 8305832 5 8 11 10.9 85 25.4 27.7 12 5 1 61,500 8305835 3 4 10 15.7 95 30.5 16 5 2 80,800 8305838 9 36.7 95,800 7 8 18.9 110 33.9 20 6 1 8305840 12 36 78,700 8305842 1 8 18.9 110 38.1 41.3 20 6 1 95,800 C=Standard stock item See p.2 for explanation of icons. WX-ST-PNC (UUNJ) is only for milling internal threads. Please select"multi-feed" for the path type in ThreadPro.
for Steels WX-ST-PNC Type 1 Type 2 Type 3 Type 4 11 P51 No. EDP No. Range of Thread SizeDia. T.P.I. Dc L n Ds Flutes Type Unit:mm Yen 8305912 3 8 19 11 85 14.7 20 12 5 3 46,000 C 8305915 3 4 14 16 85 20 16 5 4 95,800 C=Standard stock item See p.2 for explanation of icons. Please select"multi-feed" for the path type in ThreadPro. The products have been stopped producing and replaced by AT-1p.10. Solid Type No. EDP No. Range of Thread SizeDia. T.P.I. Dc L n Ds 8305949 1 16 1 8 28 5.9 60 11.8 6 4 2 Flutes Type Unit:mm Yen 31,800 8305951 1 8 28 7.5 65 14.5 15.4 8 4 1 35,800 8305961 1 43 8 19 10 75 20.1 10 5 2 37,700 8305962 3 8 19 11 85 25.4 26.7 12 5 1 C 39,500 8305964 1 2 7 8 14 12 95 32.7 12 5 2 59,100 8305965 3 47 8 14 16 110 39.9 16 5 2 78,600 8305968 1 2 11 20 125 50.8 20 6 2 103,000 C=Standard stock item See p.2 for explanation of icons. Please select"multi-feed" for the path type in ThreadPro. No. EDP No. Range of Thread SizeDia. T.P.I. Dc L n Ds 8305859 1 161 8 27 5.9 60 10.3 6 4 4 Flutes Type Unit:mm Yen 35,000 8305861 1 43 8 18 10 75 15.5 10 5 4 44,300 C 8305865 1 23 4 14 16 85 20 16 5 4 82,400 8305868 12 11½ 20 95 24.3 20 6 4 109,000 C=Standard stock item See p.2 for explanation of icons. Please select"multi-feed" for the path type in ThreadPro.
for Steels with Internal Coolant Supply WXO-ST-PNC Type 1 Type 2 11 P51 No. EDP No. Min. Cutting Bore Dia. Pitch Dc L n Ds Flutes Type Unit:mm Yen 8304700 0.75 12.8 34,800 M 6 4.5 60 15 6 4 1 8304701 1 13 34,800 8304710 0.5 16.5 34,800 8304711 M 8 1 6 65 17 6 4 2 34,800 8304712 1.25 17.5 34,800 8304721 1 21 39,300 M10 7.5 70 26 8 4 1 8304723 1.5 22.5 39,300 8304732 1.25 26.3 43,900 8304733 M12 1.5 9.5 85 25.5 28 10 5 1 43,900 8304734 1.75 26.3 43,900 8304740 0.5 28.5 43,900 8304741 0.75 29.3 C 43,900 8304742 M14 1 10 85 29 10 5 2 43,900 8304743 1.5 30 43,900 8304744 2 30 43,900 8304752 1 33 65,300 8304753 M16 1.5 12 95 34.5 12 5 2 65,300 8304754 2 34 65,300 8304773 1.5 42 83,700 M20 16 105 16 5 2 8304775 2.5 42.5 83,700 8304783 1.5 49.5 111,000 8304784 M24 2 20 120 50 20 6 2 111,000 8304786 3 51 111,000 C=Standard stock item See p.2 for explanation of icons. WXO-ST-PNC (M) is only for milling internal threads. Please select"multi-feed" for the path type in ThreadPro.
for Nonferrous Metal and Heat-Resistant Alloy WX-PNC Type 1 Type 2 30 P51 No. EDP No. Min. Cutting Bore Dia. Pitch Dc L 12.8 n Ds Flutes Type Yen 3900000 0.75 31,000 M 6 4.5 60 15 6 3 1 3900001 1 13 31,000 3900009 0.5 16.5 31,000 3900011 M 8 1 6 65 17 6 3 2 31,000 3900012 1.25 17.5 31,000 3900021 1 21 34,800 M10 7.5 70 26 8 3 1 3900023 1.5 22.5 34,800 3900032 1.25 26.3 39,000 3900033 M12 1.5 9.5 85 25.5 28 10 4 1 39,000 3900034 1.75 26.3 39,000 B 3900036 0.5 28.5 39,000 3900041 0.75 29.3 39,000 3900042 M14 1 10 85 29 10 4 2 39,000 3900043 1.5 30 39,000 3900044 2 30 39,000 3900052 1 33 57,500 3900053 M16 1.5 12 95 34.5 12 4 2 57,500 3900054 2 34 57,500 3900065 M18 2.5 14 105 40 45 16 4 1 69,800 3900073 1.5 42 73,800 M20 16 105 16 4 2 3900075 2.5 42.5 C 76,400 3900083 1.5 49.5 B 96,200 3900084 M27 2 20 120 50 20 5 2 99,800 C 3900086 3 51 99,800 Unit:mm B, C=Standard stock item See p.2 for explanation of icons. WX-PNC (M) is only for milling internal threads. Please select"multi-feed" for the path type in ThreadPro. Solid Type
for Nonferrous Metal and Heat-Resistant Alloy WX-PNC Type 1 Type 2 30 P51 No. EDP No. Min. Cutting Bore Dia. T.P.I. Dc L n Ds Flutes Type Yen 3900350 20 10.2 11.4 31,800 1 4 4.55 60 6 3 1 3900351 28 10 10.9 31,800 3900355 18 31,800 5 16 6.2 65 12.7 14.1 8 3 1 3900356 24 31,800 3900360 16 14.3 31,800 3 8 7.6 65 8 3 2 3900361 24 14.8 31,800 3900365 14 18.1 19.9 36,100 7 16 8.8 75 10 3 1 3900366 20 17.8 19.1 36,100 3900370 13 19.5 21.5 C 36,100 1 2 9.4 75 10 4 1 3900371 20 19.1 20.4 36,100 3900375 12 10.9 23.3 25.4 59,600 9 16 85 12 4 1 3900380 18 11.4 22.6 24 59,600 3900382 5 8 11 10.9 85 25.4 27.7 12 4 1 59,600 3900385 3 4 10 15.7 95 30.5 16 4 2 78,600 3900388 9 36.7 93,000 7 8 18.9 110 33.9 20 4 1 3900390 12 36 76,400 3900392 1 8 18.9 110 38.1 41.3 20 4 1 93,000 Unit:mm C=Standard stock item See p.2 for explanation of icons. WX-PNC (UUNJ) is only for milling internal threads. Please select"multi-feed" for the path type in ThreadPro.
for Nonferrous Metal and Heat-Resistant Alloy WX-PNC Type 1 Type 2 Type 3 Type 4 30 P51 No. EDP No. Range of Thread SizeDia. T.P.I. Dc L n Ds 3900199 1 161 8 28 5.9 60 9.1 6 3 4 Flutes Type Unit:mm Yen 34,000 3900201 1 8 28 7.5 60 9.1 12.7 8 3 3 38,500 3900211 1 43 8 19 10 75 14.7 10 4 4 42,800 B 3900212 3 8 19 11 85 14.7 20 12 4 3 44,700 3900214 1 23 4 14 12 85 20 12 4 4 63,200 3900215 3 4 14 16 85 20 16 4 4 93,000 3900218 12 11 20 95 27.7 20 5 4 C 105,000 Solid Type B, C=Standard stock item See p.2 for explanation of icons. Please select"multi-feed" for the path type in ThreadPro. No. EDP No. Range of Thread SizeDia. T.P.I. Dc L n Ds Flutes Type Unit:mm Yen 3900299 1 161 8 28 5.9 60 11.8 6 3 2 31,000 3900301 1 8 28 7.5 65 14.5 15.4 8 3 1 34,800 3900311 1 43 8 19 10 75 20.1 10 4 2 36,600 3900312 3 8 19 11 85 25.4 26.7 12 4 1 C 38,500 3900314 1 2 7 8 14 12 95 32.7 12 4 2 57,300 3900315 3 47 8 14 16 110 39.9 16 4 2 76,200 3900318 12 11 20 125 50.8 20 5 2 99,500 C=Standard stock item See p.2 for explanation of icons. Please select"multi-feed" for the path type in ThreadPro. No. EDP No. Range of Thread SizeDia. T.P.I. Dc L n Ds Flutes Type Yen 3900259 1 161 8 27 5.9 60 10.3 6 3 4 34,000 B 3900261 1 43 8 18 10 75 15.5 10 4 4 42,800 3900265 1 23 4 14 16 85 20 16 4 4 80,200 C 3900268 12 11½ 20 95 24.3 20 5 4 105,000 Unit:mm B, C=Standard stock item See p.2 for explanation of icons. Please select"multi-feed" for the path type in ThreadPro.
for General Purpose, Solid Carbide Spiral-Fulted Type OT-SFT-PNGT Type 1 Type 2 15 P52 No. EDP No. Min. Cutting Bore Dia. Pitch Dc L n Ds Flutes Type Yen 8306501 M 6 1 4.5 60 12 6 3 1 47,300 8306532 1.25 65,900 M12 9 90 24 10 4 1 8306534 1.75 65,900 8306542 1 77,600 35 8306543 M14 1.5 10 90 25 10 4 2 77,600 8306544 2 B 77,600 8306554 M16 2 12 105 30 12 4 2 93,900 8306575 M20 2.5 16 125 40 16 4 2 134,000 8306583 1.5 60 197,000 8306584 M27 2 20 145 50 20 5 2 197,000 8306586 3 197,000 Unit:mm B=Standard stock item See p.2 for explanation of icons. OT-SFT-PNGT (M) is only for milling internal threads. Please select"multi-feed" for the path type in ThreadPro. The products have been stopped producing and replaced by AT-1 p.10.
for General Purpose, Solid Carbide Type OT-PNGT Type 1 Type 2 P52 No. EDP No. Min. Cutting Bore Dia. Pitch Dc L n Ds Flutes Type Unit:mm Yen 8306232 1.25 62,600 M12 9 90 24 10 4 1 8306234 1.75 62,600 8306241 1 35 74,300 M14 10 90 25 10 4 2 8306245 2 74,300 B 8306273 1.5 50 128,000 M20 16 125 40 16 4 2 8306276 2.5 128,000 8306285 2 188,000 M27 20 145 50 20 5 2 8306287 3 188,000 Solid Type B=Standard stock item See p.2 for explanation of icons. OT-PNGT (M) is only for milling internal threads. Please select"multi-feed" for the path type in ThreadPro. The products have been stopped producing and replaced by AT-1 p.8.
for General Purpose, Solid Carbide Type OT-PNGT Type 2 Type 3 P52 No. EDP No. Range of Thread SizeDia. T.P.I. Dc L n Ds Flutes Type Unit:mm Yen 8306310 3 8 19 10 80 16 23 10 4 3 80,700 8306316 3 4 14 16 110 25 35 16 4 3 B 141,000 8306320 1 2 11 20 125 32 42 20 5 3 208,000 B=Standard stock item See p.2 for explanation of icons. Please select"multi-feed" for the path type in ThreadPro. The products have been stopped producing and replaced by AT-1p.10. No. EDP No. Range of Thread SizeDia. T.P.I. Dc L n Ds Flutes Type Unit:mm Yen 8306410 3 8 19 10 80 16 23 10 4 2 73,800 8306416 3 47 8 14 16 110 25 35 16 4 2 B 128,000 8306420 1 2 11 20 125 32 20 5 2 188,000 B=Standard stock item See p.2 for explanation of icons. Please select"multi-feed" for the path type in ThreadPro. The products have been stopped producing and replaced by AT-1p.10.
for HSS PNGT Type 1 Type 3 P52 No. EDP No. Min. Cutting Bore Dia. Pitch Dc L n Ds Flutes Type Unit:mm Yen 8306012 1 44,900 M14 10 90 25 32 10 4 1 8306013 1.5 41,100 8306022 1 47,600 8306023 M16 1.5 12 105 30 38 12 4 1 44,000 8306024 2 44,000 8306032 1 54,500 8306033 1.5 50,000 8306034 M20 2 16 125 40 50 16 4 1 50,000 8306035 2.5 50,000 8306036 3 50,000 8306042 1 60,800 B 8306043 1.5 55,600 8306044 M27 2 20 145 50 60 20 5 1 55,600 8306046 3 55,600 8306047 3.5 55,600 8306052 1 71,000 8306053 1.5 65,300 M34 25 165 65 20 6 3 8306054 2 65,300 8306056 3 65,300 8306063 1.5 76,800 8306064 M42 2 32 210 80 25 6 3 76,800 8306066 3 76,800 Solid Type B=Standard stock item See p.2 for explanation of icons. PNGT (M) is only for milling internal threads. Please select"multi-feed" for the path type in ThreadPro.
for HSS PNGT Type 1 Type 2 Type 3 Type 4 P52 No. EDP No. Range of Thread SizeDia. T.P.I. Dc L n Ds Flutes Type Unit:mm Yen 8306111 3 8 19 10 80 16 23 10 4 2 47,100 8306114 1 23 4 14 12 95 20 28 12 4 2 50,400 8306115 3 4 14 16 110 25 35 16 4 2 B 54,900 8306118 1 2 11 20 125 32 42.5 20 5 2 59,700 8306119 1-1 226 11 32 175 50 25 6 4 77,700 B=Standard stock item See p.2 for explanation of icons. Please select"multi-feed" for the path type in ThreadPro. No. EDP No. Range of Thread SizeDia. T.P.I. Dc L n Ds Flutes Type Unit:mm Yen 8306121 3 8 19 10 80 16 23 10 4 1 39,800 8306124 1 27 8 14 12 95 20 12 4 1 42,300 8306125 3 47 8 14 16 110 25 35 16 4 1 B 46,500 8306128 13-1 2 11 20 125 32 42.5 20 5 1 50,600 8306129 1-1 26 11 32 175 50 25 6 1 66,300 B=Standard stock item See p.2 for explanation of icons. Please select"multi-feed" for the path type in ThreadPro. P52 No. EDP No. Range of Thread SizeDia. T.P.I. Dc L n Ds Flutes Type Unit:mm Yen 8306131 3 8 19 10 80 16 23 10 4 1 39,800 8306134 1 27 8 14 12 95 20 12 4 1 42,300 8306135 3 47 8 14 16 110 25 35 16 4 1 B 46,500 8306138 13-1 2 11 20 125 32 42.5 20 5 1 50,600 8306139 1-1 26 11 32 175 50 25 6 3 66,300 B=Standard stock item See p.2 for explanation of icons. PNGT (G (PF)) is only for milling internal threads. Please select"multi-feed" for the path type in ThreadPro.
Super-Planet Cutter for Multifunction Milling DR-PNAC No. EDP No. Mill Dia 25 Dc P55 L L2 n LS L3 d1 ds d2 Ds Flutes Unit:mm Yen 8330400 M 6 1-2D 4.8 62 12.1 1 14.7 36 5 6.3 7 8 2 60,200 8330412 M 8 1.25-2D 6.5 75 15.1 1.3 18.5 40 6.8 8.3 9 10 2 69,300 8330413 M 8 1-2D 6.7 75 15.1 1.3 18.5 40 7 8.3 9 10 2 72,800 8330424 M 10 1.5-2D 8.2 79 19.6 1.5 23.7 45 8.5 10.3 11 12 2 78,600 8330425 M 10 1.25-2D 8.5 79 20.1 1.5 24 45 8.8 10.3 11 12 2 C 82,400 8330426 M 10 1-2D 8.7 79 20.1 1.5 24 45 9 10.3 11 12 2 82,400 8330436 M 12 1.75-2D 9.9 89 22.9 1.8 27.4 48 10.3 12.3 13.5 16 2 105,000 8330437 M 12 1.5-2D 10.2 89 24.1 1.8 28.6 48 10.5 12.3 13.5 16 2 110,000 8330438 M 12 1.25-2D 10.2 89 23.9 1.8 28.3 48 10.8 12.3 13.5 16 2 110,000 Solid Type C=Standard stock item See p.2 for explanation of icons. DR-PNAC is only for milling internal threads. Tapping lengththread dia.2 "Multi-feed" must be selected for the path type in ThreadPro. "Single-feed" is not applicable. Super-Planet Cutter for Multifunction Milling with Internal Coolant Supply DR-O-PNAC No. EDP No. Mill Dia 25 Dc L L2 n LS L3 d1 ds d2 Ds Flutes Yen 8330500 M 6 1-2D 4.8 62 12.1 1 14.7 36 5 6.3 7 8 2 65,900 8330512 M 8 1.25-2D 6.5 75 15.1 1.3 18.5 40 6.8 8.3 9 10 2 75,400 C 8330524 M 10 1.5-2D 8.2 79 19.6 1.5 23.7 45 8.5 10.3 11 12 2 84,800 8330536 M 12 1.75-2D 9.9 89 22.9 1.8 27.4 48 10.3 12.3 13.5 16 2 113,000 P55 Unit:mm C=Standard stock item See p.2 for explanation of icons. DR-O-PNAC is only for milling internal threads. DR-O-PNAC has oil hole. Tapping lengththread dia.2 "Multi-feed" must be selected for the path type in ThreadPro. "Single-feed" is not applicable.
How to choose HYPRO-P (Indexable Thread Mill) HY-PRO Planet Cutter is capable of mounting inserts on a single body even with differences in thread type Q. Q. Which thread cutting tool is suitable for this specific thread size? Q. Q. Is this insert mountable on this body? Q. Q. What is the first thing to consider when selecting a tool? Please refer the following hints for selecting tools to suit your specific needs. Example: I want to cut M56 x 3.5 threads with a tapping length of 82 mm. How should I choose the tools? STEP 1 Pitch P3.5 Identify the appropriate pitch and thread size on the selection chart (p. 27 to 34). Multi-Point Single Point Thread Size Tool Holder Insert Tool Holder Insert M 30 M 37 TMC25-5 124/004 53.5 SO TM 028/008 M 30 TM2SC 18C23-86-2U 2UDC60 TM TM3SC 20C26-105-2U 2UDC60 TM M 36 TM4SC 25C31-115-2U 2UDC60 TM M 41 TMC25-5 124/004 53.5 SO TM2 M 42 TM3SC 28C36-144-3U 3UDE60 TM M 46 TMC25-5TMLC25-5 53.5 SO TM2 M 48 TM4SC D42-16-3U 3UDE60 TM M 53 TMC32-5TMLC32-5TMNC32-5 53.5 SO TM2 M 54 TM5SC D48-22-3U 3UDE60 TM M 58 TM2C32-5 53.5 SO TM2 M 62 TM6SC D56-22-3U 3UDE60 TM STEP 2 In the identified items, look for bodys that can be used for cutting 82 mm of tapping length. Appropriate tool = Tapping length + (Pitch x 1.5) < is... Multi-Point Single-Point Example : M563.5, tapping length = 82mm 82mm1.5 87.25mm 3.5mm1.5P These are recommended values to ensure effective tapping length. Please make adjustment depending on the cutting condition. Consequently, look for bodys that are at least 87.25 mm in neck length / maximum milling length. Multi-Point Single-Point Shell Type Type n TMC25-5 124/004 40 TMC25-5 52 TMC32-5 58 TMLC25-5 92 TMLC32-5 98 TMNC32-5 58 Type L1 TM2SC 18C23-86-2U 86 TM3SC 20C26-105-2U 105 TM4SC 25C31-115-2U 115 TM3SC 28C36-144-3U 144 Appropriate tool differ depends on arbor to be mounted. Please consider tools with arbor.
ThreadPro follows these steps automatically. Revamped Thread Milling NC Code Generator Software Data entry screen Enter information via dropdown list! Search results Tool selection done in a split second! Indexable Thread Mill for detail for FAQ Example: What type of tool should I choose? Choose a tool that suits your work environment and purpose. Multi-Point Many variations Suitable for pipe threads can be cut A single piece of insert has multiple crests to cut the corresponding number of threads. For both internal and external threads Single-Point (Cylindrical Shank) Suitable for large diameter threads, such as eyebolts. One type of insert can cut different pitches Three corners per insert Multiple inserts achieves high-efficiency cutting Adjustable overhang length for specific cutting conditions
Tool Selection Guide by Screw Size Metric screw thread (internal) Pitch P0.5 P0.75 P1 P1.25 P1.5 Thread Size Multi-Point Single Point Tool Body Insert Tool Body Insert M 13 TMC12-2TMC20-2 20.5 SO TM2 M 17 TMC16-3 124/001 30.5 SO TM2 TMNC16-3 30.5 SO TM2 M 19 TM2C20-2 20.5 SO TM2 TMC16-3 30.5 SO TM2 M 21 TMNC20-3 30.5 SO TM2 M 22 TMC20-3 30.5 SO TM2 M 24 TMLC25-3 30.5 SO TM2 M 28 TM2C25-3 30.5 SO TM2 M 51 TMSH-D50-FMA25.4-3 30.5 SO TM2 M 14 TMC12-2TMC20-2 20.75 SO TM2 M 18 TMC16-3 124/001TMNC16-3 30.75 SO TM2 M 19 TM2C20-2 20.75 SO TM2 TMC16-3 30.75 SO TM2 M 22 TMNC20-3 30.75 SO TM2 M 23 TMC20-3 30.75 SO TM2 M 25 TMLC25-3 30.75 SO TM2 M 29 TM2C25-3 30.75 SO TM2 M 52 TMSH-D50-FMA25.4-3 30.75 SO TM2 M 15 TMC12-2TMC20-2 21.0 SO TM2 M 19 TMC16-3 124/001 31.0 SO TM2 TMNC16-3 31.0 SO TM2 M 20 TM2C20-2 21.0 SO TM2 TMC16-3 31.0 SO TM2 M 22 TMNC20-3 31.0 SO TM2 M 23 TMC20-3 31.0 SO TM2 M 25 TMLC25-3 31.0 SO TM2 M 28 TMC25-5 124/004 51.0 SO TM2 M 29 TM2C25-3 31.0 SO TM2 M 33 TMC25-5TMLC25-5 51.0 SO TM2 M 41 TMC32-5TMLC32-5TMNC32-5 51.0 SO TM2 M 46 TM2C32-5 51.0 SO TM2 M 53 TMSH-D50-FMA25.4-3 31.0 SO TM2 M 66 TMSH-D63-FMA25.4-5 51.0 SO TM2 M 83 TMSH-D80-FMA25.4-5 51.0 SO TM2 M 103 TMSH-D100-FMA31.75-5 51.0 SO TM2 M 128 TMSH-D125-FMA38.1-5 51.0 SO TM2 M 16 TMC12-2TMC20-2 21.25 SO TM2 M 20 TMC16-3 124/001 31.25 SO TM2 TMNC16-3 31.25 SO TM2 M 21 TM2C20-2 21.25 SO TM2 TMC16-3 31.25 SO TM2 M 23 TMNC20-3 31.25 SO TM2 M 24 TMC20-3 31.25 SO TM2 M 26 TMLC25-3 31.25 SO TM2 M 29 TMC25-5 124/004 51.25 SO TM2 M 30 TM2C25-3 31.25 SO TM2 M 35 TMC25-5TMLC25-5 51.25 SO TM2 M 42 TMC32-5TMLC32-5TMNC32-5 51.25 SO TM2 M 48 TM2C32-5 51.25 SO TM2 M 55 TMSH-D50-FMA25.4-3 31.25 SO TM2 M 68 TMSH-D63-FMA25.4-5 51.25 SO TM2 M 85 TMSH-D80-FMA25.4-5 51.25 SO TM2 M 105 TMSH-D100-FMA31.75-5 51.25 SO TM2 M 130 TMSH-D125-FMA38.1-5 51.25 SO TM2 M 16 TMC12-2TMC20-2 21.5 SO TM2 TMC16-3 124/001 31.5 SO TM2 M 20 TMNC16-3 31.5 SO TM2 Blue characteres are special order items. NEXT
FROM Pitch P1.5 P1.75 P2 Thread Size Multi-Point Single Point Tool Body Insert Tool Body Insert M 22 TM2C20-2 21.5 SO TM2 TMC16-3 31.5 SO TM2 M 24 TMNC20-3 31.5 SO TM2 M 25 TMC20-3 31.5 SO TM2 M 26 TM2SC 18C23-86-2U 2UIDB60 TM M 27 TMLC25-3 31.5 SO TM2 M 28 TM3SC 20C26-105-2U 2UIDB60 TM M 30 TMC25-5 124/004 51.5 SO TM2 M 31 TM2C25-3 31.5 SO TM2 M 33 TM4SC 25C31-115-2U 2UIDB60 TM M 35 TMC25-5TMLC25-5 51.5 SO TM2 M 39 TM3SC 28C36-144-3U 3UIDB60 TM M 40 TMC32-6B 6B1.5 SO TM2 M 43 TMC32-5TMLC32-5TMNC32-5 51.5 SO TM2 M 45 TM4SC D42-16-3U 3UIDB60 TM M 48 TM2C32-5 51.5 SO TM2 M 51 TMC40-6B 6B1.5 SO TM2 M 52 TM5SC D48-22-3U 3UIDB60 TM M 56 TMSH-D50-FMA25.4-3 51.5 SO TM2 M 59 TMLC42-6B 6B1.5 SO TM2 M 60 TM6SC D56-22-3U 3UIDB60 TM M 69 TMSH-D63-FMA25.4-5 51.5 SO TM2 M 86 TMSH-D80-FMA25.4-6B 6B1.5 SO TM2 TMSH-D80-FMA25.4-5 51.5 SO TM2 M 106 TMSH-D100-FMA31.75-5 51.5 SO TM2 M 131 TMSH-D125-FMA38.1-5 51.5 SO TM2 M 21 TMC16-3 124/001TMNC16-3 31.75 SO TM2 M 23 TMC16-3 31.75 SO TM2 M 25 TMNC20-3 31.75 SO TM2 M 26 TMC20-3 31.75 SO TM2 M 28 TMLC25-3 31.75 SO TM2 M 31 TMC25-5 124/004 51.75 SO TM2 M 32 TM2C25-3 31.75 SO TM2 M 36 TMC25-5TMLC25-5 51.75 SO TM2 M 44 TMC32-5TMLC32-5TMNC32-5 51.75 SO TM2 M 49 TM2C32-5 51.75 SO TM2 M 57 TMSH-D50-FMA25.4-3 31.75 SO TM2 M 70 TMSH-D63-FMA25.4-5 51.75 SO TM2 M 87 TMSH-D80-FMA25.4-5 51.75 SO TM2 M 107 TMSH-D100-FMA31.75-5 51.75 SO TM2 M 132 TMSH-D125-FMA38.1-5 51.75 SO TM2 M 14 M21 TMC12-2TMC20-2 22.0 SO TM 028/004 M 22 TMC16-3 124/001TMNC16-3 32.0 SO TM2 M 23 TMC16-3 32.0 SO TM2 M 25 TMNC20-3 32.0 SO TM2 M 26 TMC20-3 32.0 SO TM2 TM2SC 18C23-86-2U 2UIDB60 TM M 28 TMLC25-3 32.0 SO TM2 M 29 TM3SC 20C26-105-2U 2UIDB60 TM M 32 TMC25-5 124/004 52.0 SO TM2 M 33 TM2C25-3 32.0 SO TM2 M 34 TM4SC 25C31-115-2U 2UIDB60 TM M 37 TMC25-5TMLC25-5 52.0 SO TM2 M 39 TM3SC 28C36-144-3U 3UIDB60 TM M 42 TMC32-6B 6B2.0 SO TM2 M 44 TMC32-5TMLC32-5TMNC32-5 52.0 SO TM2 M 45 TM4SC D42-16-3U 3UIDB60 TM M 50 TM2C32-5 52.0 SO TM2 M 52 TM5SC D48-22-3U 3UIDB60 TM Indexable Thread MillBlue characteres are special order items. NEXT
Tool Selection Guide by Screw Size FROM Pitch P2 P2.5 P3 P3.5 Multi-Point Single Point Thread Size Tool Body Insert Tool Body Insert M 53 TMC40-6B 6B2.0 SO TM2 M 57 TMSH-D50-FMA25.4-3 32.0 SO TM2 M 60 TMLC42-6B 6B2.0 SO TM2 TM6SC D56-22-3U 3UDB60 TM M 70 TMSH-D63-FMA25.4-5 52.0 SO TM2 M 87 TMSH-D80-FMA25.4-6B 6B2.0 SO TM2 TMSH-D80-FMA25.4-5 52.0 SO TM2 M 107 TMSH-D100-FMA31.75-5 52.0 SO TM2 M 132 TMSH-D125-FMA38.1-5 52.0 SO TM2 M 20 M 21 TMC16-3 124/001 32.5 SO TM 028/005 M 22 M 34 TMC25-4 124/002 42.5 SO TM 028/006 M 27 TM2SC 18C23-86-2U 2UDC60 TM M 30 TM3SC 20C26-105-2U 2UDC60 TM M 34 TMC25-5 124/004 52.5 SO TM2 TM4SC 25C31-115-2U 2UDC60 TM M 40 TMC25-5TMLC25-5 52.5 SO TM2 TM3SC 28C36-144-3U 3UDE60 TM M 46 TM4SC D42-16-3U 3UDE60 TM M 47 TMC32-5TMLC32-5TMNC32-5 52.5 SO TM2 M 52 TM2C32-5 52.5 SO TM2 TM5SC D48-22-3U 3UDE60 TM M 60 TM6SC D56-22-3U 3UDE60 TM M 73 TMSH-D63-FMA25.4-5 52.5 SO TM2 M 90 TMSH-D80-FMA25.4-5 52.5 SO TM2 M 110 TMSH-D100-FMA31.75-5 52.5 SO TM2 M 135 TMSH-D125-FMA38.1-5 52.5 SO TM2 M 24 M 35 TMC25-4 124/002 43.0 SO TM 028/007 M 27 TM2SC 18C23-86-2U 2UDC60 TM M 30 TM3SC 20C26-105-2U 2UDC60 TM M 35 TM4SC 25C31-115-2U 2UDC60 TM M 36 M 42 TMC25-5TMLC25-5 53.0 SO TM 028/009 M 37 TMC25-5 124/004 53.0 SO TM2 M 41 TM3SC 28C36-144-3U 3UDE60 TM M 42 TMC25-5TMLC25-5 53.0 SO TM2 M 47 TMC32-6B 6B3.0 SO TM2 M 48 TM4SC D42-16-3U 3UDE60 TM M 50 TMC32-5TMLC32-5TMNC32-5 53.0 SO TM2 M 52 TM5SC D48-22-3U 3UDE60 TM M 55 TM2C32-5 53.0 SO TM2 M 58 TMC40-6BTMLC42-6B 6B3.0 SO TM2 M 60 TM6SC D56-22-3U 3UDE60 TM M 75 TMSH-D63-FMA25.4-5 53.0 SO TM2 M 92 TMSH-D80-FMA25.4-6B 6B3.0 SO TM2 TMSH-D80-FMA25.4-5 53.0 SO TM2 M 112 TMSH-D100-FMA31.75-5 53.0 SO TM2 M 137 TMSH-D125-FMA38.1-5 53.0 SO TM2 M 30 TM2SC 18C23-86-2U 2UDC60 TM TM3SC 20C26-105-2U 2UDC60 TM M 30 M 37 TMC25-5 124/004 53.5 SO TM 028/008 M 36 TM4SC 25C31-115-2U 2UDC60 TM M 41 TMC25-5 124/004 53.5 SO TM2 M 42 TM3SC 28C36-144-3U 3UDE60 TM M 46 TMC25-5TMLC25-5 53.5 SO TM2 M 48 TM4SC D42-16-3U 3UDE60 TM M 53 TMC32-5TMLC32-5TMNC32-5 53.5 SO TM2 M 54 TM5SC D48-22-3U 3UDE60 TM M 58 TM2C32-5 53.5 SO TM2 M 62 TM6SC D56-22-3U 3UDE60 TM M 77 TMSH-D63-FMA25.4-5 53.5 SO TM2 M 94 TMSH-D80-FMA25.4-5 53.5 SO TM2 Blue characteres are special order items. NEXT
FROM Pitch P3.5 P4 P4.5 P5 P5.5 P6 Multi-Point Single Point Thread Size Tool Body Insert Tool Body Insert M 114 TMSH-D100-FMA31.75-5 53.5 SO TM2 M 139 TMSH-D125-FMA38.1-5 53.5 SO TM2 TM2SC 18C23-86-2U 2UDC60 TM M 36 TM3SC 20C26-105-2U 2UDC60 TM TM4SC 25C31-115-2U 2UDC60 TM M 36 M 42 TMC25-5TMLC25-5 54.0 SO TM 028/010 M 42 TM3SC 28C36-144-3U 3UDH60 TM M 44 TMC25-5 124/004 54.0 SO TM2 M 48 TMC25-5TMLC25-5 54.0 SO TM2 TM4SC D42-16-3U 3UDH60 TM M 54 TMC32-6B 6B4.0 SO TM2 M 55 TM5SC D48-22-3U 3UDH60 TM M 56 TMC32-5TMLC32-5TMNC32-5 54.0 SO TM2 M 60 TMC40-6B 6B4.0 SO TM2 M 62 TM2C32-5 54.0 SO TM2 M 64 TM6SC D56-22-3U 3UDH60 TM M 68 TMLC42-6B 6B4.0 SO TM2 M 78 TMSH-D63-FMA25.4-5 54.0 SO TM2 M 95 TMSH-D80-FMA25.4-6B 6B4.0 SO TM2 TMSH-D80-FMA25.4-5 54.0 SO TM2 M 115 TMSH-D100-FMA31.75-5 54.0 SO TM2 M 140 TMSH-D125-FMA38.1-5 54.0 SO TM2 M 42 TM3SC 28C36-144-3U 3UDH60 TM M 42 M 52 TMC25-5TMLC25-5 54.5 SO TM 028/011 M 48 TMC25-5 124/004 54.5 SO TM2 TM4SC D42-16-3U 3UDH60 TM M 53 TMC25-5TMLC25-5 54.5 SO TM2 M 54 TM5SC D48-22-3U 3UDH60 TM M 58 TMC32-6B 6B4.5 SO TM2 M 60 TMC32-5TMLC32-5TMNC32-5 54.5 SO TM2 TMC40-6B 6B4.5 SO TM2 M 62 TM6SC D56-22-3U 3UDH60 TM M 66 TM2C32-5 54.5 SO TM2 M 70 TMLC42-6B 6B4.5 SO TM2 M 80 TMSH-D63-FMA25.4-5 54.5 SO TM2 M 97 TMSH-D80-FMA25.4-6B 6B4.5 SO TM2 TMSH-D80-FMA25.4-5 54.5 SO TM2 M 117 TMSH-D100-FMA31.75-5 54.5 SO TM2 M 142 TMSH-D125-FMA38.1-5 54.5 SO TM2 M 48 TMC32-6B 6B5.0 SO TM2 TM3SC 28C36-144-3U 3UDH60 TM TM4SC D42-16-3U 3UDH60 TM M 54 TM5SC D48-22-3U 3UDH60 TM M 58 TMC40-6B 6B5.0 SO TM2 M 62 TM6SC D56-22-3U 3UDH60 TM M 72 TMLC42-6B 6B5.0 SO TM2 M 99 TMSH-D80-FMA25.4-6B 6B5.0 SO TM2 TM3SC 28C36-144-3U 3UDH60 TM M 56 TMC32-6B 6B5.5 SO TM2 TM4SC D42-16-3U 3UDH60 TM TM5SC D48-22-3U 3UDH60 TM M 60 TMC40-6B 6B5.5 SO TM2 M 63 TM6SC D56-22-3U 3UDH60 TM M 74 TMLC42-6B 6B5.5 SO TM2 M 101 TMSH-D80-FMA25.4-6B 6B5.5 SO TM2 M 64 TMC32-6BTMC40-6B 6B6.0 SO TM2 M 76 TMLC42-6B 6B6.0 SO TM2 M 103 TMSH-D80-FMA25.4-6B 6B6.0 SO TM2 TM3SC 28C36-144-3U TM4SC D42-16-3U TM5SC D48-22-3U TM6SC D56-22-3U 3UDH60 TM 3UDH60 TM 3UDH60 TM 3UDH60 TM Indexable Thread MillBlue characteres are special order items. 1.5 NoteTo machine external screwthreads, tool must be selected as below : holder outer dia./internal screwthread outer dia.(nominal dia.) 1.5
Tool Selection Guide by Screw Size Unified screw thread (internal) T.P.I. 48 32 28 24 20 18 Thread Size Multi-Point Single Point Tool Body Insert Tool Body Insert ½ TMC12-2TMC20-2 248 UN TM2 ¾ TM2C20-2 248 UN TM2 9 16 TMC12-2TMC20-2 232 UN TM2 11 16 TMC16-3 124/001 TMNC16-3 332 UN TM2 ¾ TM2C20-2 232 UN TM2 TMC16-3 332 UN TM2 7 8 TMNC20-3TMC20-3 332 UN TM2 1 TMLC25-3 332 UN TM2 1 1 8 TM2C25-3 332 UN TM2 9 16 TMC12-2TMC20-2 228 UN TM2 ¾ TMC16-3TMC16-3 124/001 TMNC16-3 328 UN TM2 13 16 TM2C20-2 228 UN TM2 TMC16-3 328 UN TM2 7 8 TMNC20-3 328 UN TM2 15 16 TMC20-3 328 UN TM2 1 TMLC25-3 328 UN TM2 1 3 16 TM2C25-3 328 UN TM2 9 16 TMC12-2TMC20-2 224 UN TM2 ¾ TMC16-3 124/001 TMNC16-3 324 UN TM2 13 16 TM2C20-2 224 UN TM2 TMC16-3 324 UN TM2 7 8 TMNC20-3 324 UN TM2 15 16 TMC20-3 324 UN TM2 1 TMLC25-3 324 UN TM2 1 1 8 TMC25-5 124/004 524 UN TM2 1 3 16 TM2C25-3 324 UN TM2 1 5 16 TMC25-5TMLC25-5 524 UN TM2 1 5 8 TMC32-5TMLC32-5 TMNC32-5 524 UN TM2 1 7 8 TM2C32-5 524 UN TM2 5 8 TMC12-2TMC20-2 220 UN TM2 13 16 TMC16-3 124/001 TMNC16-3 320 UN TM2 7 8 TM2C20-2 220 UN TM2 TMC16-3 320 UN TM2 15 16 TMNC20-3 320 UN TM2 1 TMC20-3 320 UN TM2 1 1 16 TMLC25-3 320 UN TM2 1 3 16 TM2C25-3 320 UN TM2 TMC25-5 124/004 520 UN TM2 1 3 8 TMC25-5TMLC25-5 520 UN TM2 1 5 8 TMC32-5TMLC32-5 TMNC32-5 520 UN TM2 1 7 8 TM2C32-5 520 UN TM2 11 16 TMC12-2TMC20-2 218 UN TM2 13 16 TMC16-3 124/001 TMNC16-3 318 UN TM2 7 8 TM2C20-2 218 UN TM2 TMC16-3 318 UN TM2 15 16 TMNC20-3 318 UN TM2 1 TMC20-3 318 UN TM2 1 1 16 TMLC25-3 318 UN TM2 1 3 16 TMC25-5 124/004 518 UN TM2 1 ¼ TM2C25-3 318 UN TM2 1 3 8 TMC25-5TMLC25-5 518 UN TM2 Blue characteres are special order items. NEXT
FROM T.P.I. 18 16 14 13 12 Thread Size Multi-Point Single Point Tool Body Insert Tool Body Insert 1 11 16 TMC32-5TMLC32-5 TMNC32-5 518 UN TM2 115 16 TM2C32-5 518 UN TM2 11 16 TMC12-2TMC20-2 216 UN TM2 13 16 TMC16-3 124/001 TMNC16-3 316 UN TM2 7 8 TM2C20-2 216 UN TM2 TMC16-3 316 UN TM2 15 16 TMNC20-3 316 UN TM2 1 TMC20-3 316 UN TM2 TM2SC 18C23-86-2U 2UDB60 TM 1 1 16 TMLC25-3 316 UN TM2 1 1 8 TM3SC 20C26-105-2U 2UDB60 TM 1 3 16 TMC25-5 124/004 516 UN TM2 1 ¼ TM2C25-3 316 UN TM2 1 3 8 TM4SC 25C31-115-2U 2UDB60 TM 1 7 16 TMC25-5TMLC25-5 516 UN TM2 1 9 16 TM3SC 28C36-144-3U 3UDB60 TM 1 11 16 TMC32-5TMLC32-5 TMNC32-5 516 UN TM2 1 ¾ TM4SC D42-16-3U 3UDB60 TM 115 16 TM2C32-5 516 UN TM2 2 TM5SC D48-22-3U 3UDB60 TM 2 3 8 TM6SC D56-22-3U 3UDB60 TM 11 16 TMC12-2TMC20-2 214 UN TM2 7 8 TMC16-3 124/001 TMNC16-3 314 UN TM2 15 16 TM2C20-2 214 UN TM2 TMC16-3 314 UN TM2 1 TMNC20-3TMC20-3 314 UN TM2 TM2SC 18C23-86-2U 2UDB60 TM 1 1 8 TMLC25-3 314 UN TM2 TM3SC 20C26-105-2U 2UDB60 TM 1 ¼ TM2C25-3 314 UN TM2 TMC25-5 124/004 514 UN TM2 1 3 8 TM4SC 25C31-115-2U 2UDB60 TM 1 7 16 TMC25-5TMLC25-5 514 UN TM2 1 5 8 TM3SC 28C36-144-3U 3UDB60 TM 1 ¾ TMC32-5TMLC32-5 TMNC32-5 514 UN TM2 TM4SC D42-16-3U 3UDB60 TM 115 16 TM2C32-5 514 UN TM2 2 TM5SC D48-22-3U 3UDB60 TM 2 3 8 TM6SC D56-22-3U 3UDB60 TM 7 8 TMC16-3 124/001 TMNC16-3 313 UN TM2 15 16 TMC16-3 313 UN TM2 1 TMNC20-3 313 UN TM2 1 1 16 TMC20-3 313 UN TM2 1 1 8 TMLC25-3 313 UN TM2 1 ¼ TMC25-5 124/004 513 UN TM2 1 5 16 TM2C25-3 313 UN TM2 1 ½ TMC25-5TMLC25-5 513 UN TM2 1 ¾ TMC32-5TMLC32-5 TMNC32-5 513 UN TM2 2 TM2C32-5 513 UN TM2 7 8 TMC16-3 124/001 TMNC16-3 312 UN TM2 15 16 TMC16-3 312 UN TM2 1 TMNC20-3 312 UN TM2 1 1 16 TMC20-3 312 UN TM2 TM2SC 18C23-86-2U 2UDB60 TM 1 1 8 TMLC25-3 312 UN TM2 Indexable Thread MillBlue characteres are special order items. NEXT
Tool Selection Guide by Screw Size FROM T.P.I. 12 11.5 11 10 9 8 Thread Size Multi-Point Single Point Tool Body Insert Tool Body Insert 1 3 16 TM3SC 20C26-105-2U 2UDB60 TM 1 ¼ TMC25-5 124/004 512 UN TM2 1 5 16 TM2C25-3 312 UN TM2 1 3 8 TM4SC 25C31-115-2U 2UDB60 TM 1 ½ TMC25-5TMLC25-5 512 UN TM2 1 9 16 TM3SC 28C36-144-3U 3UDB60 TM 1 ¾ TMC32-5TMLC32-5 TMNC32-5 512 UN TM2 113 16 TM4SC D42-16-3U 3UDB60 TM 2 TM2C32-5 512 UN TM2 TM5SC D48-22-3U 3UDB60 TM 2 3 8 TM6SC D56-22-3U 3UDB60 TM 7 8 TMC16-3 124/001 TMNC16-3 311.5 UN TM2 15 16 TMC16-3 311.5 UN TM2 1 1 16 TMNC20-3TMC20-3 311.5 UN TM2 1 3 16 TMLC25-3 311.5 UN TM2 1 ¼ TMC25-5 124/004 511.5 UN TM2 1 5 16 TM2C25-3 311.5 UN TM2 1 ½ TMC25-5TMLC25-5 511.5 UN TM2 113 16 TMC32-5TMLC32-5 TMNC32-5 511.5 UN TM2 2 TM2C32-5 511.5 UN TM2 1 ¼ TMC25-5 124/004 511 UN TM2 1 ½ TMC25-5TMLC25-5 511 UN TM2 1 3 16 TMC32-5TMLC32-5 TMNC32-5 511 UN TM2 2 TM2C32-5 511 UN TM2 1 1 16 TM2SC 18C23-86-2U 2UDC60 TM 1 ¼ TM3SC 20C26-105-2U 2UDC60 TM 1 5 16 TMC25-5 124/004 510 UN TM2 1 3 8 TM4SC 25C31-115-2U 2UDC60 TM 1 9 16 TMC25-5TMLC25-5 510 UN TM2 1 5 8 TM3SC 28C36-144-3U 3UDE60 TM 1 7 8 TMC32-5TMLC32-5 TMNC32-5 510 UN TM2 TM4SC D42-16-3U 3UDE60 TM 2 1 16 TM2C32-5 510 UN TM2 2 ¼ TM5SC D48-22-3U 3UDE60 TM 2 ½ TM6SC D56-22-3U 3UDE60 TM 1 3 8 TMC25-5 124/004 59 UN TM2 1 11 16 TMC25-5TMLC25-5 59 UN TM2 2 TMC32-5TMLC32-5 TMNC32-5 59 UN TM2 2 3 16 TM2C32-5 59 UN TM2 1 1 16 TM2SC 18C23-86-2U 2UDC60 TM 1 3 16 TM3SC 20C26-105-2U 2UDC60 TM 1 3 8 TMC25-5 124/004 58 UN TM2 1 7 16 TM4SC 25C31-115-2U 2UDC60 TM 1 5 8 TM3SC 28C36-144-3U 3UDE60 TM 1 11 16 TMC25-5TMLC25-5 58 UN TM2 113 16 TM4SC D42-16-3U 3UDE60 TM 2 TMC32-5TMLC32-5 TMNC32-5 58 UN TM2 2 1 8 TM5SC D48-22-3U 3UDE60 TM 2 3 16 TM2C32-5 58 UN TM2 2 3 8 TM6SC D56-22-3U 3UDE60 TM Blue characteres are special order items. NEXT
FROM T.P.I. Thread Size Multi-Point Single Point Tool Body Insert Tool Body Insert 1 ½ TMC25-5 124/004 57 UN TM2 1 13 16 TMC25-5TMLC25-5 57 UN TM2 7 2 1 8 TMC32-5TMLC32-5 TMNC32-5 57 UN TM2 2 11 16 TM2C32-5 57 UN TM2 1 3 8 TM2SC 18C23-86-2U TM3SC 20C26-105-2U 2UDC60 TM 2UDC60 TM 1 ½ TM4SC 25C31-115-2U 2UDC60 TM 1 5 8 TMC25-5 124/004 56 UN TM2 TM3SC 28C36-144-3U 3UDH60 TM 1 15 16 TM4SC D42-16-3U 3UDH60 TM 2 TMC25-5TMLC25-5 56 UN TM2 6 2 1 8 TM5SC D48-22-3U 3UDH60 TM 2 3 16 TMC32-6B 6B6 UN TM2 2 ¼ TMC32-5TMLC32-5 TMNC32-5 56 UN TM2 2 7 16 TM2C32-5 56 UN TM2 2 3 8 TMC40-6B 6B6 UN TM2 2 ½ TM6SC D56-22-3U 3UDH60 TM 2 9 16 TMLC42-6B 6B6 UN TM2 1 ¾ TM3SC 28C36-144-3U 3UDH60 TM 1 7 8 TMC32-6B 6B5 UN TM2 1 15 16 TM4SC D42-16-3U 3UDH60 TM 5 4.5 2 3 16 TM5SC D48-22-3U 3UDH60 TM 2 5 16 TMC40-6B 6B5 UN TM2 2 ½ TM6SC D56-22-3U 3UDH60 TM 2 7 8 TMLC42-6B 6B5 UN TM2 2 TMC32-6B 6B4.5 UN TM2 TM3SC 28C36-144-3U 3UDH60 TM TM4SC D42-16-3U 3UDH60 TM 2 ¼ TMLC42-6B 6B4.5 UN TM2 TM5SC D48-22-3U 3UDH60 TM 2 3 8 TMC40-6B 6B4.5 UN TM2 115 16 TMLC42-6B 6B4.5 UN TM2 Indexable Thread Mill2 ½ TM6SC D56-22-3U 3UDH60 TM 2 1 16 TMLC42-6B 6B4 UN TM2 TMC32-6BTMC40-6B 6B4 UN TM2 TM3SC 28C36-144-3U 3UDH60 TM 4 2 ½ TM4SC D48-16-3U TM5SC D48-22-3U 3UDH60 TM 3UDH60 TM TM6SC D56-22-3U 3UDH60 TM Blue characteres are special order items.
Description (Straight Shank Body, Multi-Point) TMNC20-3LH Shape Type Oil hole Shank Size Insert Size Type Thread Milling Non L 2 N 1 Standard, 1 Insert 1 Long Neck, 1 Insert 2 with 2 Inserts 1 for Taper Pipe Threads Internal Coolant C All sizes are with oil hole 1242 Shank Sizes: 12 to 42 Insert Size No. 2 3 4 5 6B Insert Size 1 4" 3 8" 1 2" 5 8" 3 4"B Inscribed Circle 6.35 mm 10 mm 12.7 mm 15.875mm 19.05 mm Non 124/*** RighHand LH Left Hand HY-PRO P Multi-Point HY-PRO P PNTC TMC Body (1 insertstandard type P52 P.40~P.47 Unit:mm EDP No. Type Insert Size No. L n Ds D D Yen 7710112 TMC12-2 70 12 12 30,500 7710132 TMC20-2 2 8.9 11.5 33,800 85 20 20 7710232 TMC20-2LH 33,800 7710023 TMC16-3 124/001 91 20.5 16 12.2 15.5 42,500 7710123 TMC16-3 3 90 22 16 13.6 17 33,600 7710133 TMC20-3 95 43 20 16.6 20 36,900 C 7710044 TMC25-4 124/002 4 88 30 25 13.4 18 52,900 7710045 TMC25-5 124/004 98 40 19 25 52,900 7710145 TMC25-5 25 42,500 5 110 52 24 30 7710245 TMC25-5LH 42,500 7710155 TMC32-5 120 58 32 31 37 48,400 7710156 TMC32-6B 115 53 32 27 35 47,900 6B TMC40-6B 135 63 40 38 46 C=Standard stock item =Special order items See p.2 for explanation of icons. For cautions of using LH Body : please refer to p.38 To use in combination with a insert, please refer to the Tool Selection Guide by Screw Sizeon p.27 or utilize our NC code generator softwarethreadproto automatically select the best option available. Please select"multi-feed" for the path type in ThreadPro.
HY-PRO P Multi-Point HY-PRO P PNTC TMLC1TMLC Body (1 insertlong type P52 P.40~P.47 Unit:mm No. EDP No. Type Insert Size No. L n Ds D D Yen 7710343 TMLC25-3 3 125 25 25 18.6 22 52,200 7710345 TMLC25-5 150 92 25 24 30 52,200 5 C 7710355 TMLC32-5 160 98 32 31 37 60,400 7710366 TMLC42-6B 6B 200 80 42 45 53 94,200 C=Standard stock item See p.2 for explanation of icons. To use in combination with a insert, please refer to the Tool Selection Guide by Screw Sizeon p.27 or utilize our NC code generator softwarethreadproto automatically select the best option available. Please select"multi-feed" for the path type in ThreadPro. Indexable Thread Mill Precautions for using normal holder The normal body is right-handed. The normal body can be used to mill both right and left-handed threads. (Note) To machine external screwthreads, tool must be selected as below : body outer dia. 1.5 internal screwthread outer dia. (nominal dia.)
HY-PRO P Multi-Point HY-PRO P PNTC TM2C Body ( 2 inserts, high efficiency type P52 P.40~P.47 Unit:mm EDP No. Type Insert Size No. L n Ds D D Yen 7710532 TM2C20-2 2 85 20 20 14.4 17 49,300 7710543 TM2C25-3 3 100 43 25 22.5 26 C 62,100 7710555 TM2C32-5 5 120 45 32 36 42 71,400 C=Standard stock item TMNC Body ( 1 insertfor taper pipe threads P52 P.40~P.47 Unit:mm EDP No. Type Insert Size No. L n Ds s D D Yen 7710723 TMNC16-3 90 22 16 48 12.5 15.5 33,600 7710823 TMNC16-3LH 80 22 16 48 12.5 15.5 33,600 3 C 7710733 TMNC20-3 85 23 20 50.9 15 19 36,900 7710833 TMNC20-3LH 85 23 20 50.9 15 19 36,900 TMNC32-5 5 120 58 32 60.3 31 37 TMNC32-5LH C=Standard stock item =Special order items See p.2 for explanation of icons. For cautions of using LH Body : please refer to p.38 To use in combination with a insert, please refer to the Tool Selection Guide by Screw Sizeon p.27 or utilize our NC code generator softwarethreadproto automatically select the best option available. Please select"multi-feed" for the path type in ThreadPro.
Parts Insert Size No. Tool Body EDP No. Overall Length includes screw head. Type Screw Thread Size Overall Length EDP No. Wrench 2 7710902 SN2TM M 2.6 0.45 5.9 7808205 T8-D 3 TMLC25-3 TM2C25-3 7710943 SN3T No.5-40UNC 9.5 Type 7808207 T10-D 7710903 SN3TM No.5-40UNC 8 4 7710904 SN4TM No.8-32UNC 10.7 7808209 T20-D TMC25-5 124/004 7710955 SA5TM M 5 0.8 12.8 5 7808210 T25-D 7710905 SN5TM M 5 0.8 15 6B 7710907 SM7T M 7 1 15 7808212 T30-T Precautions for selecting bodys for pipe inserts: Two faces of pipe inserts can be used, one marked with (or without) the letter R, and another with the letter L. To use a pipe insert with a face marked with (or without) the letter R, use a body that does not have the code LH at the end of its designation. To use a pipe insert with a face marked with letter L, use a body that has the code LH at the end of its designation. Because an insert is sloped, both faces of an insert cannot be used on the same body. Careful with the direction of cutting edges. Indexable Thread MillPrecautions for using LH body The LH body is left-handed. To mill threads, operate the main shaft in reverse. The LH body can be used to mill both right and left-handed threads. Precautions for using normal body The normal body is right-handed. The normal body can be used to mill both right and left-handed threads. LH Body Normal Body (Note) To machine external screwthreads, tool must be selected as below : body outer dia. 1.5 internal screwthread outer dia. (nominal dia.)
Description (Shell Type Body, Multi-Point) TMSH-D100-FMA31.75-5 Thread Milling Shell Type D D D2 D2 50125 D2 sizes: 50 to 125 FMA FMA type face mill arbor d1 Insert Size Insert Size No. 3 5 6B Insert Size 3 8" 5 8" ¾"B Inscribed Circle 10 mm 15.875mm 19.05 mm HY-PRO P Multi-Point HY-PRO P PNTC Type 1 Type 2 P52 P.40~P.47 Shell Type D b d d l l t EDP No. Description Insert Size No. D d H No. of Flutes Type Clamping Bolt Yen 7710891 TMSH-D50-FMA25.4-3 3 50 46.5 9.5 25.4 20 46.5 48 12.5 26 6.3 6 1 M12 Unit:mm 172,000 7710892 TMSH-D63-FMA25.4-5 63 57 4 172,000 5 9.5 25.4 20 54.8 48 12.5 26 6.3 1 M12 7710893 TMSH-D80-FMA25.4-5 80 74 6 190,000 C 7710894 TMSH-D80-FMA25.4-6B 6B 80 72 9.5 25.4 20 54.8 48 12.5 26 6.3 5 1 M12 190,000 7710895 TMSH-D100-FMA31.75-5 100 94 12.7 31.75 48 73.8 48 32.3 8 7 2 MBA-M16 203,000 5 7710896 TMSH-D125-FMA38.1-5 125 119 15.9 38.1 60 98.8 61 38 10 9 2 MBA-M20 220,000 Parts C=Standard stock item See p.2 for explanation of icons. Please use with FMA type face mill arbor To use in combination with a insert, please refer to the Tool Selection Guide by Screw Sizeon p.27 or utilize our NC code generator softwarethreadproto automatically select the best option available. Please select multi-feedfor the path type in ThreadPro. Insert Size No. No. EDP No. Type Screw Thread Size Overall Length No. EDP No. Wrench 3 7710903 SN3TM No.5-40UNC 8 7808207 T10-D 5 7710905 SN5TM M 5 0.8 15 7808210 T25-D 6B 7710907 SM7T M 7 1 15 7808212 T30-T Overall Length includes screw head. Type
Description (Insert, Multi-Point) 3 1.5 SO TM 2 Insert Size No. 2 3 4 5 6B Insert Size Insert Size ¼" 3 8" ½" 5 8" ¾"B d Inscribed Circle 6.35 mm 10 mm 12.7 mm 15.875mm 19.05 mm Applications Internal thread E External thread E for both applications or Pitch or T.P.I. SO BSPT NPTF W UN Thread Type Metric screw threads British taper pipe thread National taper pipe thread for dry sealing Parallel pipe threads Unified screw threads Thread Milling 028/*** 2 Insert 1 for 1 piece insert type (applying to corse pitch thread) 12 for both 1 and 2 pieces insert type HY-PRO P Multi-Point HY-PRO P PC-CTI Inserts for Metric screw thread (internal) Type 1 Type 2 P.35~P.39 Tool Material Surface Treatment VBX TiCN C VTX TiAlN VK2 Sizes marked with are special order items. Indexable Thread Mill Unit:mm Description Insert Size No. Pitch Le No. of threads Type Material VBX Yen 2 0.5 SO TM2 0.5 10 20 1 7711082 8,610 2 0.75 SO TM2 0.75 10.5 14 1 7711092 8,610 2 1.0 SO TM2 1 10 10 1 7711102 7,330 2 2 1.25 SO TM2 1.25 8.75 7 1 7711112 C 7,330 2 1.5 SO TM2 1.5 10.5 7 1 7711122 7,330 2 2.0 SO TM 028/004 2 10 5 1 7711542 7,330 3 0.5 SO TM2 0.5 15 30 1 7711083 10,100 3 0.75 SO TM2 0.75 15 20 1 3 1.0 SO TM2 1 15 15 1 7711103 3 1.25 SO TM2 1.25 15 12 1 7711113 8,610 3 3 1.5 SO TM2 1.5 15 10 1 7711123 8,610 C 3 1.75 SO TM2 1.75 14 8 1 7711133 8,610 3 2.0 SO TM2 2 14 7 1 7711143 8,610 3 2.5 SO TM 028/005 2.5 12.5 5 2 7711553 8,610 C=Standard stock item =Special order items See p. 41 for precaution for use. 8,610 NEXT
HY-PRO P Multi-Point HY-PRO P PC-CTI Inserts for Metric screw thread (internal) FROM Type 1 Type 2 P.35~P.39 Tool Material Surface Treatment VBX TiCN C VTX TiAlN VK2 Sizes marked with are special order items. Unit:mm Description Listed price: per insert Insert Size No. Pitch Le No. of threads Type Material VBX Yen 4 2.5 SO TM 028/006 2.5 17.5 7 2 7711554 12,500 4 4 3.0 SO TM 028/007 3 18 6 2 7711564 12,500 5 1.0 SO TM2 1 26 26 1 7711105 16,500 5 1.25 SO TM2 1.25 25 20 1 7711115 16,500 5 1.5 SO TM2 1.5 25.5 17 1 7711125 16,500 5 1.75 SO TM2 1.75 24.5 14 1 7711135 16,500 5 2.0 SO TM2 2 24 12 1 7711145 16,500 5 2.5 SO TM2 2.5 25 10 1 7711155 16,500 C 5 3.0 SO TM2 3 24 8 1 7711165 16,500 5 5 3.0 SO TM 028/009 3 24 8 1 7711565 16,500 5 3.5 SO TM2 3.5 24.5 7 1 7711175 16,500 5 3.5 SO TM 028/008 3.5 24.5 7 1 7711575 16,500 5 4.0 SO TM2 4 24 6 1 7711185 16,500 5 4.0 SO TM 028/010 4 24 6 1 7711585 16,500 5 4.5 SO TM2 4.5 22.5 5 1 7711195 16,500 5 4.5 SO TM 028/011 4.5 22.5 5 1 7711595 16,500 6B 1.5 SO TM2 1.5 36 24 1 7715456 19,500 6B 2.0 SO TM2 2 36 18 1 7715466 19,500 6B 3.0 SO TM2 3 36 12 1 7715476 19,500 6B 4.0 SO TM2 4 32 8 1 7715486 19,500 6B C 6B 4.5 SO TM2 4.5 31.5 7 1 7715496 19,500 6B 5.0 SO TM2 5 30 6 1 7715506 19,500 6B 5.5 SO TM2 5.5 33 6 1 7715516 19,500 6B 6.0 SO TM2 6 30 5 1 7715526 19,500 C=Standard stock item See p.2 for explanation of icons. Order/packing unit : Insert Size No.235 pieces Insert Size No.456B1 piece To use in combination with bodys, please refer to the Tool Selection Guide by Screw Sizeon p.27 or utilize our NC code generator softwarethreadproto automatically select the best option available. Please select multi-feedfor the path type in ThreadPro.
HY-PRO P PC-CTI Inserts for Metric screw thread (external) P.35~P.39 Tool Material Surface Treatment VBX TiCN C VTX TiAlN VK2 Sizes marked with are special order items. Description Insert Size No. Pitch Le No. of threads Material Unit:mm C=Standard stock item =Special order items See p. 41 for precaution for use. VBX Yen 2E 0.75 SO TM2 0.75 10.5 14 7712092 8,610 2E 1.0 SO TM2 1 10 10 7712102 7,330 2 C 2E 1.25 SO TM2 1.25 10 8 7712112 7,330 2E 1.5 SO TM2 1.5 9 6 7712122 7,330 3E 0.75 SO TM2 0.75 15 20 3E 1.0 SO TM2 1 14 14 7712103 3E 1.25 SO TM2 1.25 15 12 7712113 C 8,610 3 3E 1.5 SO TM2 1.5 15 10 7712123 8,610 3E 1.75 SO TM2 1.75 14 8 3E 2.0 SO TM2 2 14 7 7712143 8,610 5E 1.0 SO TM2 1 26 26 7712105 16,500 5E 1.25 SO TM2 1.25 25 20 7712115 16,500 5E 1.5 SO TM2 1.5 25.5 17 7712125 16,500 5E 1.75 SO TM2 1.75 24.5 14 7712135 16,500 5E 2.0 SO TM2 2 24 12 7712145 16,500 5 5E 2.5 SO TM2 2.5 25 10 7712155 16,500 5E 3.0 SO TM2 3 24 8 7712165 16,500 5E 3.5 SO TM2 3.5 24.5 7 7712175 16,500 5E 4.0 SO TM2 4 24 6 7712185 C 16,500 5E 4.5 SO TM2 4.5 22.5 5 7712195 16,500 6BE 1.5 SO TM2 1.5 36 24 7716456 19,500 6BE 2.0 SO TM2 2 36 18 7716466 19,500 6BE 3.0 SO TM2 3 36 12 7716476 19,500 6BE 4.0 SO TM2 4 32 8 7716486 19,500 6B 6BE 4.5 SO TM2 4.5 31.5 7 7716496 19,500 6BE 5.0 SO TM2 5 30 6 7716506 19,500 6BE 5.5 SO TM2 5.5 33 6 7716516 19,500 6BE 6.0 SO TM2 6 30 5 7716526 19,500 8,610 Indexable Thread Mill
HY-PRO P Multi-Point HY-PRO P PC-CTI Inserts for straight pipe and Withworth threads (internal & external) Description Insert Size No. T.P.I. P.35~P.39 Le Tool Material Surface Treatment VBX TiCN C VTX TiAlN VK2 Sizes marked with are special order items. Inserts for Taper pipe threads (internal & external) No. of threads Tool body Screw thread size Material Unit:mm Yen 2E 19 W TM2 19 9.36 7 3 8" 7713542 6,100 2 TMC12-2, TMC20-2 2E 14 W TM2 14 9.07 5 1 2", 5 8" 7713572 6,100 3E 14 W TM2 14 14.51 8 TMC16-3, TMC20-3 3 4", 7 8" 7713573 7,170 3 C 3E 11 W TM2 11 13.85 6 TMC16-3, TMC20-3 1, 1-1 8" 7713593 7,170 5E 11 W TM2 5 11 23.09 10 TMC25-5 1-1 4" 1-1 2",1-3 4" TMC32-5 2" VBX 7713595 13,700 C=Standard stock item P.35~P.39 Unit:mm Description Insert Size No. T.P.I. Le No. of threads Tool body Screw thread size Material 2E 19 BSPT TM2 2 19 9.36 7 TMC20-2, TMC20-2LH 3 8" 7713042 3E 14 BSPT TM2 14 14.51 8 3 3E 11 BSPT TM2 11 13.85 6 5E 11 BSPT TM2 5 11 23.09 10 TMNC16-3, TMNC16-3LH 1 2", 3 4" TMNC20-3, TMNC20-3LH 3 4" TMNC16-3, TMNC16-3LH TMNC20-3, TMNC20-3LH TMC25-5 124/004 1-1 4" 4" TMC25-5, TMC25-5LH, TMLC25-5 TMC32-5, TMLC32-5 TMNC32-5, TMNC32-5LH TM2C32-5 VBX Yen C=Standard stock item Blue characteres are special order items. See p. 44 for precaution for use. When tapping length is shorter than Le, other options for holder + insert combination may be possible. C 6,100 7713073 7,170 1", 1-1 4", 1-1 2" 7713093 7,170 1-1 4" 2" 2-1 2" 7713095 13,700
Unit:mm Unit:mm Description Insert Size No. T.P.I. Le No. of threads Tool body Screw thread size Material VBX Yen TMNC16-3, TMNC16-3LH ½" 3E 14 NPT TM2 3 14 14.51 8 7713163 8,610 TMNC16-3 124/001 ¾" TMNC16-3, TMNC16-3LH 3E 11.5 NPT TM2 3 11.5 13.25 6 TMNC20-3,TMNC20-3LH 1"2" 7713183 8,610 TMC25-5 124/004 TMC25-5, TMC25-5LH,TMLC25-5 1-¼" 5E 11.5 NPT TM2 5 11 24.3 11 TMC25-5 124/004 TMC25-5, TMC25-5LH,TMLC25-5 TMC32-5, TMLC32-5 TMNC32-5, TMNC32-5LH 1-½" C 7713285 16,500 TMC25-5 124/004 TMC25-5, TMC25-5LH,TMLC25-5 TM2C32-5,TMC32-5, TMLC32-5 TMNC32-5, TMNC32-5LH 2 5E 8 NPT TM2 5 8 22.23 7 TMC25-5 124/004 TMNC32-5, TMNC32-5LH 2-½",3" 7713305 16,500 C=Standard stock item Description Insert Size No. T.P.I. Le No. of threads Tool body Screw thread size Material VBX Yen 3E 14 NPTF TM2 14 14.51 8 TMNC16-3, TMNC16-3LH ½" 7713173 8,610 3E 14 NPTF TM2 3 14 14.51 8 TMNC16-3, TMNC16-3LH ¾" 7713173 8,610 3E 11.5 NPTF TM2 11.5 13.25 6 TMNC20-3, TMNC20-3LH 1"2" 7713193 8,610 5E 11.5 NPTF TM2 TMC25-5, TMC25-5LH, TMLC25-5 C 1-¼" 2" 11.5 24.3 11 TMC25-5 124/004 7713295 5 TMC32-5, TMLC32-5 2" 16,500 5E 8 NPTF TM2 8 22.23 7 TMNC32-5, TMNC32-5LH 2-½",3" 7713315 16,500 Listed price: per insert C=Standard stock item See p.2 for explanation of icons. Blue characteres are special order items. For the LH Body : see p.38 Order/packing unit : Insert Size No.235 pieces Insert Size No.51 piece Please select multi-feedfor the path type in ThreadPro. Indexable Thread MillType of Inserts Material Features VBX VTX VK2 For general steel and cast iron TiCN Ultra-fine grain carbide and TiCN coating Material with excellent chipping and wear resistance For stainless steel TiAIN Ultra-fine grain carbide and TiAlN coating Material with excellent chipping and wear resistance Carbide non-coated For non-ferrous metals such as aluminum, heat-resistance alloy and titanium alloy
HY-PRO P Multi-Point HY-PRO P PC-CTI Inserts for Unified screw thread (internal) P.35~P.39 Tool Material Surface Treatment VBX TiCN C VTX TiAlN VK2 Sizes marked with are special order items. Description Insert Size No. T.P.I. Le No. of threads Material VBX Unit:mm Yen 2 48 UN TM2 48 10.05 19 7711202 8,610 C 2 40 UN TM2 40 10.16 16 7711212 8,610 2 32 UN TM2 32 10.32 13 2 28 UN TM2 28 9.98 11 2 27 UN TM2 27 10.35 11 7711242 7,330 2 2 24 UN TM2 24 9.53 9 7711252 7,330 2 20 UN TM2 20 10.16 8 7711262 7,330 C 2 18 UN TM2 18 9.88 7 7711272 7,330 2 16 UN TM2 16 9.53 6 7711282 7,330 2 14 UN TM2 14 9.07 5 7711292 7,330 3 40 UN TM2 40 14.61 23 3 32 UN TM2 32 15.08 19 3 28 UN TM2 28 14.51 16 7711213 8,610 C 3 27 UN TM2 27 14.11 15 7711223 8,610 3 24 UN TM2 24 14.82 14 3 20 UN TM2 20 13.97 11 7711243 8,610 3 3 18 UN TM2 18 14.11 10 7711253 8,610 3 16 UN TM2 16 14.29 9 7711263 8,610 3 14 UN TM2 14 14.51 8 7711273 C 8,610 3 13 UN TM2 13 13.68 7 7711283 8,610 3 12 UN TM2 12 14.82 7 7711293 8,610 3 11.5 UN TM2 11.5 13.25 6 7711303 8,610 Listed price: per insert C=Standard stock item =Special order items See p.2 for explanation of icons. Order/packing unit: Insert Size No.235 pieces To use in combination with bodys, please refer to the Tool Selection Guide by Screw Sizeon p.27 or utilize our NC code generator softwarethreadproto automatically select the best option available. Please select multi-feedfor the path type in ThreadPro. NEXT
FROM Unit:mm Description Insert Size No. T.P.I. Le No. of threads Material VBX Yen 5 24 UN TM2 24 25.4 24 7711235 16,500 5 20 UN TM2 20 25.4 20 7711245 16,500 5 18 UN TM2 18 25.4 18 7711255 16,500 5 16 UN TM2 16 25.4 16 7711265 16,500 5 14 UN TM2 14 25.4 14 7711275 16,500 5 13 UN TM2 13 25.4 13 7711285 16,500 C 5 12 UN TM2 12 25.4 12 7711295 16,500 5 5 11.5 UN TM2 11.5 24.3 11 7711315 16,500 5 11 UN TM2 11 25.4 11 7711325 16,500 5 10 UN TM2 10 25.4 10 7711335 16,500 5 9 UN TM2 9 22.58 8 7711345 16,500 5 8 UN TM2 8 22.23 7 7711305 16,500 5 7 UN TM2 7 25.4 7 5 6 UN TM2 6 25.4 6 6B 6 UN TM2 6 33.87 8 7715606 19,500 6B 5 UN TM2 5 30.48 6 7715616 19,500 6B C 6B 4.5 UN TM2 4.5 33.87 6 7715626 19,500 6B 4 UN TM2 4 31.75 5 7715636 19,500 Listed price: per insert C=Standard stock item =Special order items See p.2 for explanation of icons. Order/packing unit: Insert Size No.56B1 piece To use in combination with bodys, please refer to the Tool Selection Guide by Screw Sizeon p.27 or utilize our NC code generator softwarethreadproto automatically select the best option available. Please select multi-feedfor the path type in ThreadPro. Indexable Thread Mill
HY-PRO P Multi-Point HY-PRO P PC-CTI Inserts for Unified screw thread (external) P.35~P.39 Tool Material Surface Treatment VBX TiCN C VTX TiAlN VK2 Sizes marked with are special order items. Description Insert Size No. T.P.I. Le No. of threads Material VBX Unit:mm Yen 2E 28 UN TM2 28 9.98 11 7712202 7,330 2E 24 UN TM2 24 9.53 9 7712212 7,330 2E 20 UN TM2 20 10.16 8 7712222 7,330 2 2E 18 UN TM2 18 9.88 7 7712232 7,330 2E 16 UN TM2 16 9.53 6 7712242 7,330 2E 14 UN TM2 14 9.07 5 7712252 7,330 3E 28 UN TM2 28 14.51 16 7712203 8,610 3E 27 UN TM2 27 14.11 15 7712213 8,610 3E 24 UN TM2 24 14.82 14 7712223 8,610 3E 20 UN TM2 20 13.97 11 7712233 8,610 3E 18 UN TM2 3 18 14.11 10 7712243 8,610 3E 16 UN TM2 16 14.29 9 7712253 8,610 3E 14 UN TM2 14 14.51 8 7712263 8,610 3E 13 UN TM2 13 13.68 7 7712273 8,610 C 3E 12 UN TM2 12 14.82 7 7712283 8,610 5E 24 UN TM2 24 25.4 24 7712205 16,500 5E 20 UN TM2 20 25.4 20 7712215 16,500 5E 18 UN TM2 18 25.4 18 7712225 16,500 5E 16 UN TM2 16 25.4 16 7712235 16,500 5E 14 UN TM2 14 25.4 14 7712245 16,500 5E 13 UN TM2 13 25.4 13 7712255 16,500 5E 12 UN TM2 5 12 25.4 12 7712265 16,500 5E 11 UN TM2 11 25.4 11 7712275 16,500 5E 10 UN TM2 10 22.86 9 7712285 16,500 5E 9 UN TM2 9 22.58 8 7712295 16,500 5E 8 UN TM2 8 22.23 7 7712305 16,500 5E 7 UN TM2 7 21.77 6 7712315 16,500 5E 6 UN TM2 6 21.17 5 7712325 16,500 See p. 46 for precaution for use. C=Standard stock item
Description (Straight Shank Body,Single Point ) TM4SC 25C31-115-2U Thread Milling No. of Flutes Shape Type S Single Point S All sizes are listed as S Oil hole C Internal Coolant C All sizes are with oil hole Shank Size Shank Shape C Cylindrical Shank C All sizes are listed as C D2 L Insert Size No. 2U 3U Insert Size Insert Size 1 4"U 3 8"U Inscribed Circle 6.35mm 10 mm HY-PRO P Single Point HY-PRO P PNTC P52 P.50 Indexable Thread MillSingle point body (Cylindrical Shank) Unit:mm No. EDP No. Description Insert Size No. L L L L D S D No. of Flutes Yen 7710871 TM2SC 18C23-86-2U 166 86 18 23.3 2 43,900 40 7710872 TM3SC 20C26-105-2U 2U 186 105 5.4 20 26 3 50,900 C 7710873 TM4SC 25C31-115-2U 196 115 46 25 31 4 70,000 7710874 TM3SC 28C36-144-3U 3U 222 144 8 60 28 36.5 3 67,500 C=Standard stock item See p.2 for explanation of icons. Single point body is only for milling internal threads. The maximum milling length is a reference value for general use. The minimum holding length is a reference value. The minimum holding length of the tooling to be used takes precedence. To use in combination with a insert, please refer to the Tool Selection Guide by Screw Sizeon p.27 or utilize our NC code generator softwarethreadproto automatically select the best option available. Parts Cylindrical Shank Insert Size No. EDP No. Type Screw Thread Size Overall Length EDP No. 2U 7710942 SN2T M2.60.45 6.5 7808205 T8-D 3U 7710973 SA3T No.5-40UNC 12 7808207 T10-D Overall Length includes screw head. Wrench Type
Description (Shell Type Body, Single Point) TM6SC D56-22-3U Thread Milling No. of Flutes Shape Type S Single point S All sizes are listed as S Oil hole C Internal Coolant C All sizes are with oil hole D+ D + D2 D2 42, 48, 56 D2 sizes: 42, 48, 56 d1 d1 16, 22 d1 sizes: 16, 22 Insert Size No. 3U Insert Size Insert Size 3 8"U Inscribed Circle 10mm HY-PRO P Single Point HY-PRO P PNTC P52 P.50 Single point body (Shell Type) Unit:mm No. b d t No. EDP No. Type Insert Size No. D d H L of Flutes Clamping Bolt Yen TM4SC D42-16-3U 42 8.4 16 34 19.6 5.6 4 M 8 1.25 TM5SC D48-22-3U 3U 48 40 40 8 5 10.4 22 21.1 6.3 M10 1.5 7710881 TM6SC D56-22-3U 56 48 6 C 79,700 C=Standard stock item =Special order items See p.2 for explanation of icons. Single point body is only for milling internal threads. Please use with FMH type face mill arbor. To use in combination with a insert, please refer to the Tool Selection Guide by Screw Sizeon p.27 or utilize our NC code generator softwarethreadproto automatically select the best option available. Parts Shell Type Insert Size No. EDP No. Type Screw Thread Size Overall Length EDP No. Wrench 3U 7710943 SN3T No.5-40UNC 9.5 7808207 T10-D Overall Length includes screw head. Type
Description (Insert, Single Point) 2UDB60 TM Insert Size No. 2U 3U Insert Size Insert Size 1 4"U 3 8"U Inscribed Circle 6.35mm 10 mm Internal thread DB DC DE DH Pitch and T.P.I. Pitch 1.5-2 2.5-4 2.5-3.5 4-6 T.P.I 16-12 10-6 10-7 6-4 Applicable thread types 60 Metric Unified Screw Thread Thread Milling HY-PRO P Single Point HY-PRO P PC-CTI P.48~P.49 Indexable Thread MillInserts for Metric and Unified screw thread (internal) Unit:mm No. Applicable Thread R L EDP No. Description Insert Size No. Pitch T.P.I. R Tool Material Yen 7716551 2UDB60 TM 1.5 2 16 12 0.06 3,270 2U 11 VBX 7716552 2UDC60 TM 2.5 4 10 6 0.14 3,270 7716553 3UDB60 TM 1.5 2 16 12 0.06 C 3,480 7716554 3UDE60 TM 3U 2.5 3.5 10 7 16 0.14 VBX 3,480 7716555 3UDH60 TM 4 6 6 4 0.25 3,480 Listed price: per insert C=Standard stock item See p.2 for explanation of icons. Order/packing unit5 pieces To use in combination with bodys, please refer to the Tool Selection Guide by Screw Sizeon p.27 or utilize our NC code generator softwarethreadproto automatically select the best option available. Three corners per side can be used.
Cutting Conditions Low Carbon SteelMild Steel Medium Carbon Steel High Carbon Steel Alloy Steel Cutting Speed m/min AT-1 WX-ST-PNCWXO-ST-PNC WX-PNC Feed mm/t Cutting Speed m/min Feed mm/t Cutting Speed m/min Feed mm/t C0.25% 80 160 0.01 0.05 80 120 0.04 0.1 50 75 0.01 0.11 C0.25%0.45% 80 160 0.01 0.05 80 120 0.04 0.1 C0.45% 80 160 0.01 0.05 80 120 0.04 0.1 SCM 60 120 0.01 0.05 80 120 0.02 0.08 2545HRC 80 200 0.01 0.05 60 100 0.02 0.08 Hardened Steel 4550HRC 5060HRC Stainless Steel Tool Steel Cast Steel Cast Iron Ductile Cast Iron Copper Brass Brass Casting Bronze Aluminum Rolled Steel Aluminum Alloy Casting Magnesium Alloy Casting Zinc Alloy Casting Titanium Alloy N i Nickel Alloy Thermo Setting Plastic Thermo Plastic SUS304 SUS420 60 120 0.01 0.05 40 80 0.02 0.06 SKD SC 60 120 0.01 0.05 40 65 0.02 0.09 40 65 0.02 0.09 FC 80 160 0.01 0.05 50 100 0.03 0.1 50 100 0.03 0.1 FCD 60 120 0.01 0.05 50 65 0.03 0.1 50 65 0.03 0.1 Cu 80 160 0.03 0.1 65 130 0.03 0.1 Bs 80 160 0.03 0.1 65 130 0.03 0.1 BsC 80 160 0.03 0.1 65 130 0.03 0.1 PB 80 160 0.03 0.1 65 130 0.03 0.1 Al 80 160 0.03 0.1 50 70 0.03 0.1 AC, ADC 100 300 0.05 0.2 65 130 0.03 0.1 MC 100 300 0.05 0.2 65 130 0.03 0.1 ZDC 100 300 0.05 0.2 65 130 0.03 0.1 Ti-6Al-4V 20 60 0.02 0.06 Inconel 20 60 0.01 0.03 80 160 0.03 0.1 65 130 0.03 0.13 65 130 0.03 0.13 80 160 0.03 0.1 65 130 0.03 0.13 65 130 0.03 0.13 Formula for calculating the feed rate of thread mill fz z n Dm Dc v f = mm/min Dm v f :mm/min Feed Dm :mm Actual Dia. Dc :mm Tool Dia. Note Internal External z fz n : Number of Flutes :mm/t Feed Rate :min 1 Speed For the arc cutting process of machining external and internal threads, the feed rate at the tool center can be obtained by multiplying the linear cut feed rate with a coefficient. The formulas for calculating coefficients vary between external and internal thread cutting. The formula listed left are for calculating the tool feed rate during arc-cutting, including calculating the coefficients to be used for multiplication with the linear-cut feed rate.
OT-SFT-PNGT OT-PNGT PNGT HY-PRO P Multi-Point Cutting Speed m/min Feed mm/t Cutting Speed m/min Feed mm/t Cutting Speed m/min Feed mm/t Cutting Speed m/min Feed mm/t HY-PRO P Single Point Cutting Speed m/min Feed mm/t 50 75 0.01 0.11 40 60 0.01 0.09 20 30 0.01 0.05 100 210 0.05 0.3 100 210 0.24 0.36 40 70 0.01 0.11 30 50 0.01 0.04 10 20 0.01 0.05 100 180 0.05 0.25 100 180 0.24 0.36 40 70 0.01 0.11 30 50 0.01 0.04 8 12 0.01 0.05 100 170 0.05 0.2 100 170 0.22 0.33 15 30 0.01 0.03 15 30 0.01 0.03 10 15 0.01 0.05 60 130 0.05 0.2 60 130 0.18 0.27 15 30 0.01 0.03 10 15 0.01 0.05 70 110 0.16 0.24 20 40 0.01 0.06 20 40 0.01 0.06 10 15 0.01 0.05 70 140 0.05 0.15 70 140 0.16 0.24 70 110 0.16 0.24 40 65 0.02 0.09 30 50 0.02 0.07 10 20 0.02 0.1 100 170 0.05 0.1 70 120 0.14 0.21 50 100 0.03 0.1 40 75 0.02 0.08 20 50 0.02 0.1 60 130 0.05 0.15 60 120 0.16 0.24 50 65 0.03 0.1 40 50 0.02 0.08 20 30 0.02 0.1 60 130 0.02 0.08 60 100 0.16 0.24 65 130 0.03 0.1 50 100 0.02 0.08 50 80 0.02 0.05 120 210 0.1 0.3 120 210 0.5 0.75 65 130 0.03 0.1 50 100 0.02 0.08 50 100 0.02 0.05 120 210 0.1 0.3 120 210 0.6 0.9 65 130 0.03 0.1 50 100 0.02 0.08 50 100 0.02 0.05 120 210 0.1 0.3 120 210 0.6 0.9 65 130 0.03 0.1 50 100 0.02 0.08 30 60 0.02 0.05 120 210 0.05 0.25 120 210 0.5 0.75 50 70 0.03 0.1 40 55 0.02 0.08 40 55 0.02 0.08 100 250 0.1 0.4 100 180 0.5 0.75 65 130 0.03 0.1 50 100 0.02 0.08 50 80 0.02 0.1 150 400 0.01 0.3 150 280 0.4 0.6 65 130 0.03 0.1 50 100 0.02 0.08 50 80 0.02 0.1 150 400 0.01 0.3 150 280 0.4 0.6 65 130 0.03 0.1 50 100 0.02 0.08 50 80 0.02 0.1 150 400 0.01 0.3 150 280 0.4 0.6 65 130 0.03 0.13 50 100 0.02 0.1 50 80 0.02 0.1 150 400 0.05 0.3 150 280 0.4 0.6 65 130 0.03 0.13 50 100 0.02 0.1 50 80 0.02 0.1 150 400 0.05 0.3 150 280 0.4 0.6 Recommended Conditions 1. The indicated speeds and feeds are for water soluble oil. 2. Water-soluble oil is not suitable for tapping magnesium alloy. 3. Please adjust the cutting conditions depending on the rigidity of machine, tool holders, and workpiece clamping. 4. If the tapping length is long, or when machining a large-pitch thread, select a smaller feed and separate the machining process into a few segments. 5. If a machined parallel internal thread is tapered and prevents the go-gauge from going through, add a zero cut (finish machining). 6. When frequent chipping or breakage occurs of the HY-PRO P cutting edges, it is recommended to reduce the radial depth of cut by 50%. 7. Even with the AT-1, it is possible that the go-gauge may have trouble passing through the tapered parallel internal thread. In that case, please process the 1st pass at 75% and finish the thread with the 2nd pass.
Tips for Machining with WH-VM-PNC & Recommended Cutting Conditions S1~1.4, M1~1.8 So that you can take full advantage of the small diameter thread mill Machining method (Recommended processes) Machining method Employ this machining method if cutting chips are jammed deep in the threads. Machine one pitch the entrance of the hole. Repeat arc cutting movement only 1P in the Z axial direction for each rotation. To finish, machine the hole entry. Machine one pitch the bottom of the hole. Repeat arc cutting movement only 1P in the Z axial direction for each rotation. To finish, machine the hole entry. Work Material Cutting Speed m/min Feedmm/t Dc=0.72 Dc=0.92 Dc=1.05 Dc=1.2 Dc=1.3 C0.25% 60 90 0.02 0.03 0.05 Low Carbon SteelMild Steel Medium Carbon Steel High Carbon Steel Alloy Steel Hardened Steel Stainless Steel Tool Steel Cast Steel Cast Iron Ductile Cast Iron C 0.25% 0.45% 60 90 0.02 0.03 0.05 C0.45% 60 90 0.02 0.03 0.05 SCM 2545 HRC 4555 HRC 5560 HRC SUS304 SUS420 60 90 0.02 0.03 0.05 SKD SC 40 60 0.02 0.03 0.05 FC 40 60 0.02 0.03 0.05 FCD 40 60 0.02 0.03 0.05 Copper Brass Work Material Brass Casting Bronze Aluminum Rolled Steel Aluminum Alloy Casting Magnesium Alloy Casting Zinc Alloy Casting Titanium Alloy N i Nickel Alloy Thermo Setting Plastic Thermo Plastic Cutting Speed m/min Feedmm/t Dc=0.72 Dc=0.92 Dc=1.05 Dc=1.2 Dc=1.3 Cu Bs BsC 60100 0.04 0.06 0.08 PB Al 70100 0.04 0.06 0.08 AC, ADC 70100 0.04 0.06 0.08 MC 70100 0.04 0.06 0.08 ZDC 70100 0.04 0.06 0.08 Ti-6Al-4V 20 40 0.01 0.02 0.03 Inconel 50100 0.04 0.06 0.08 50100 0.04 0.06 0.08 1. The "Recommended Cutting Conditions" include general conditions for using water-soluble coolant. The above conditions may not be applicable, depending on the machining equipment or the number of passes. They can be addressed in a wide range of ways. 2. Water-soluble oil is not suitable for tapping magnesium alloy. 3. Please adjust the cutting conditions depending on the rigidity of machine, tool holders, and workpiece clamping. 4. Please use at least two passes in order to avoid tool breakage or excessive wear. 5. If a machined parallel internal thread is tapered and prevents the go-gauge from going through, add a zero cut (finish machining).
M2~5, No.8 So that you can take full advantage of the small diameter thread mill Machining method (General materials) Machining method (Heat resistant alloys/high hardness materials) Machine three pitches at the bottom of the hole and move the tool to the center of the hole. Machine three pitches while moving in the Z direction, then return to the center of the pilot hole. (repeat this a few times) To finish, machine the hole entry. Machine three pitches at the bottom of the hole. Repeat arc cutting movement only 1P in the Z axial direction for each rotation. To finish, machine the hole entry. Work Material Low Carbon SteelMild Steel Medium Carbon Steel High Carbon Steel Cutting Speed m/min Feed mm/t C0.25% 60 90 0.02 0.08 C 0.25% 0.45% 60 90 0.02 0.08 C0.45% 60 90 0.02 0.08 Copper Brass Work Material Brass Casting Cutting Speed m/min Feed mm/t Cu Bs BsC 50 100 0.02 0.06 Alloy Steel SCM 30 60 0.01 0.03 Bronze PB 50 100 0.02 0.06 2545HRC 30 60 0.01 0.03 Aluminum Rolled Steel Al 50 100 0.02 0.06 Hardened Steel 4555HRC 30 60 0.01 0.03 Aluminum Alloy Casting AC, ADC 50 100 0.02 0.06 Stainless Steel Tool Steel 5560HRC 30 60 SUS304 SUS420 1 0.01 0.02 60 90 0.02 0.08 SKD Magnesium Alloy Casting Zinc Alloy Casting Titanium Alloy MC 50 100 0.02 0.06 ZDC 50 100 0.02 0.06 Ti-6Al-4V 20 60 0.01 0.03 Cast Steel Cast Iron SC 40 60 0.02 0.09 FC 50 100 0.03 0.1 N i Nickel Alloy Thermo Setting Plastic Inconel 20 60 0.01 0.03 50 100 0.02 0.06 Ductile Cast Iron FCD 50 70 0.03 0.1 Thermo Plastic 50 100 0.02 0.06 Recommended Conditions 1. The "Recommended Cutting Conditions" include general conditions for using water-soluble coolant. The above conditions may not be applicable, depending on the machining equipment or the number of passes. They can be addressed in a wide range of ways. 2. Water-soluble oil is not suitable for tapping magnesium alloy. 3. Please adjust the cutting conditions depending on the rigidity of machine, tool holders, and workpiece clamping. 4. If the tapping length is long, or when machining a large-pitch thread, select a smaller feed and separate the machining process into a few segments. 5. If a machined parallel internal thread is tapered and prevents the go-gauge from going through, add a zero cut (finish machining). Pay attention to conditions including the depth of cut in the machine program.
Cutting Conditions Machining Technique Start Drilling & chamfering Reverse Approach Threading Release Remove Drilling and Chamfering: The thread part of the cutter does not touch the wall of the hole because of the larger drill diameter. The cutter is pulled out 1 or 2 pitches to ensure that the helical thread motion does not interfere with the alreadymade chamfer. The amount of this removal depends on the length of milling and direction of the cutter. Finally, the thread is cut with helical milling. The best method is to mill gradually to ensure the highest level of precision. Remove tool. Work Material Cast Iron Ductile Cast Iron Aluminum Alloy Aluminum Alloy Casting Aluminum Alloy Casting for Die Casting Magnesium Alloy Casting Zinc Alloy Casting Thermo Plastic DR-PNACDR-O-PNAC Internal Threads Cutting Speed m/min Feed mm/t Drills Feed mm/rev FC 50120 0.020.04 0.1 0.2 FCD 50100 0.020.04 0.1 0.2 A 80200 0.020.05 0.1 0.2 Si13 80200 0.020.05 0.1 0.2 Si13 80200 0.020.04 0.05 0.1 MC 80200 0.020.05 0.1 0.2 ZDC 80200 0.020.05 0.1 0.2 80200 0.020.05 0.1 0.2 DR-O-PNAC is recommended for aluminum alloy. 1. The indicated speeds and feeds are for water soluble oil. 2. Water-soluble oil is not suitable for tapping magnesium alloy. 3. Please adjust the cutting conditions depending on the rigidity of machine, tool holders, and workpiece clamping. 4. If the tapping length is long, or when machining a large-pitch thread, select a smaller feed and separate the machining process into a few segments. 5. If a machined parallel internal thread is tapered and prevents the go-gauge from going through, add a zero cut (finish machining). 6. Please apply step feed when Super Planet Cutter is causing chip packing during drilling operation.
Cutting Data Effects of left-hand helix Tool Work Material Cutting Speed Feed Internal Thread Size Drill Hole Size Threading Length Machining Method Coolant Machine AT-1 7.722 P1 4F SCM440 30HRC 100m/min4,136min -1 380mm/min0.1mm/t M101mm 918mm Through 15mm 1 Climb milling 1-Pass Water-Soluble BT30 Vertical Machining Center The left-hand helixs small pitch diameter difference between the hole entry and inner hole allows a delay in gauge-out failure. Moreover, longer tool life can be achieved with zero cuttingfor correcting bending being eliminated. Comparison of differences in internal thread pitch diameter at initial cutting stage Unit:mm Right Hand Helix Left Hand Helix mm 0.14 0.12 0.1 0.08 Pitch dia. 0.06 0.04 0.02 0 Hole Entry Pitch diameter measurement method : Step gauge Inner Hole Area Changes in pitch diameter with time (rendered image) Right Hand Helix Dia. Difference +0.120 +0.140 +0.040 +0.060 0.060 0.100 +0.120 +0.140 +0.120 +0.140 0 0.020 20m Handles pitch diameter differences of 20 μm or less. Left Hand Helix 1 100 200 300 400 500 600 700 800 900 1,000 Number of processed thread holes EgiAs Effects of EgiAs coating Tool Work Material Cutting Speed Feed Internal Thread Size AT-1 7.722 P1 4F SCM440 80m/min3,307min -1 30mm/min0.01mm/t M101mm Cutting edge after threading 2,000 holes Drill Hole Size 925mm Blind Threading Length Coolant 19mm Water-Soluble EgiAs EgiAs Coating WX WX Coating Machine BT30 Vertical Machining Center Recommended ConditionsMachining Data
Cutting Data Work materials to are machined under the conditions shown below. Internal Thread Size Drill Hole Size Threading Length Coolant Machine M101 925mm Blind 19mm Water-Soluble BT30 Vertical Machining Center 1. 20m Internal thread pitch diameter difference between hole entry and inner hole area: 20m or less +0.080+0.100 1 Eg: +0.080 step gauge passes completely, +0.100 step gauge stops less than or equal to one revolution. 2. 1. Fastest cutting condition (including number of passes) while fulfilling the requirement of Condition 1. SUS304 Machining SUS304 Tool Cutting Speed Feed Number of Passes Cutting Time AT-1 7.722 P1 4F Competitor 120m/min 4,961min -1 140m/min 5,122min -1 228mm/min 0.05mm/t 200mm/min 0.1mm/t 1 Pass 2.26 sec 130% Efficiency 2 Passes 3.03 sec Number of processed thread holes Holes 1,200 1,000 800 600 400 200 0 Still Running 1,000 AT-1 170% Durability Over GP-OUT 567 Competitor S50C Machining S50C Tool Cutting Speed Feed Number of Passes Cutting Time AT-1 7.722 P1 4F Competitor 160m/min 6,614min -1 140m/min 5,122min -1 122mm/min 0.02mm/t 20mm/min 0.01mm/t 1 Pass 4.28 sec 740% Efficiency 3 Passes 45.4 sec Number of processed thread holes Holes 800 600 400 200 0 GP-OUT 750 AT-1 150% Durability GP-OUT 491 Competitor SCM440 Machining SCM440 Tool Cutting Speed Feed Number of Passes Cutting Time AT-1 7.722 P1 4F 80m/min 3,307min -1 Competitor 140m/min 5,122min -1 30mm/min 0.01mm/t 20mm/min 0.01mm/t 1 Pass 17.12 sec 350% Efficiency 4 Passes 60.54 sec Number of processed thread holes 2,500 Holes 2,000 1,500 1,000 500 0 Still Running 2,000 2,000 AT-1 Still Running Competitor
SUS304 SUS304 durability test result Tool Work Material Cutting Speed Feed Internal Thread Size Drill Hole Size Threading Length Coolant Machine Number of Passes AT-1 9.727 P1.5 5F 100m/min 3,283min -1 31mm/min 0.01mm/t SUS304 M121.5 WX-ST-PNC 9.522.5 P1.5 120m/min 4,021min -1 42mm/min 0.01mm/t 10.525mm Through 22.5mm Water-Soluble BT30 Vertical Machining Center 1 Pass 3 Passes Holes 800 600 400 200 0 sec 50 40 30 20 10 0 900 900 AT-1 17 AT-1 Number of processed thread holes Cutting Time 240% Efficiency WX-ST-PNC 41 WX-ST-PNC 1,000 Machining Data
Cutting Data Machining small diameter internal threads with stainless steel Tool Work Material WH-VM-PNC 0.72 P0.25 SUS304 Competitor Tool Life 0 100 200 Cutting Speed Feed 80m/min 35,367min -1 594mm/min 0.02mm/t WH-VM-PNC 212 Holes 235 Holes Gauge-Out Gauge-Out Internal Thread Size M10.25 Drill Hole Size Threading Length 0.782.5mm Blind 2mm 2D Blind Competitor 122 Holes 198 Holes Gauge-Out Gauge-Out Machining Method 2 Up Cut 2 passes Coolant Machine Water-Soluble HSK-E25 Vertical Machining Center The WH-VM-PNC was able to perform stably with water-soluble coolant in stainless steel, a difficult process for cut taps. It was able to achieve long tool life and perform stably when tapping M1 threads. When processing threads with limited tap drill hole depth allowance for tap drill holes, the WH-VM-PNC was able to perform more stably than a conventional cut tap. 718 Machining small diameter internal threads with Inconel 718 Tool Work Material Cutting Speed Feed Internal Thread Size Drill Hole Size WH-VM-PNC 3.22.4 U32 Inconel 718 40HRC 40m/min 3,980min -1 120mm/min 0.03mm/t No.10-32 UNF 60m/min 5,970min -1 180mm/min 0.03mm/t 4.114mm Blind Cutting Speed 40m/min 60m/min No. of Passes 4 Number of processed thread holes 20 40 60 80 50 Holes 2 40 Holes 60 Holes Substantial tool chipping Substantial tool chipping Substantial tool chipping Threading Length Machining Method Coolant Machine 9mm 1.9D Blind 24 Down Cut 24 passes Water-Soluble HSK-A40 Vertical Machining Center Compared to taps, thread mills have fewer cutting condition limitations. There are no worries about chip management or coolant lubricity, and stable tapping is possible. In this example, we were able to improve the yield rate of small diameter internal threads in a high value workpiece. Further durability improvements and cost reductions can be expected by adjusting the feed rate and number of passes, and changing the cutting fluid.
Outstanding Performance in Stainless with Water-Soluble Coolant Tool Work Material WX-ST-PNC 7.59.1RC 28 SUS304 Number of processed thread holes 500 1,000 1,500 Cutting Speed Feed 130m/min 5,970min -1 607mm/min 0.1mm/t WX-ST-PNC 1,315 Holes Gauge-Out Internal Thread Size Rc1/8-28 Drill Hole Size Threading Length 8.29mm Through 6.2mm A CompetitorA 1,217 Holes Gauge-Out Machining Method Coolant Down Cut Water-Soluble B Competitor B 1,000 Holes Gauge-Out Machine BT40 Vertical Machining Center Tool life comparison against other competitors under identical cutting condition in SUS304. The tool life of the WX-ST-PNC was slightly higher than other competitors. Also, in terms of tool wear, it was the only tool that was in fair enough condition for regrinding. Tool Wear Amount WX-ST-PNC WX-ST-PNC Stable Performance in S45C Tool WX-ST-PNC 7.59.1RC 28 Pitch-dia. Reduced amount Work Material Cutting Speed Feed Internal Thread Size Drill Hole Size Threading Length Machining Method Coolant S45C 100m/min 4,592min -1 327mm/min 0.07mm/t Rc1/8-28 8.29mm Through 6.2mm Down Cut Water-Soluble WX-ST-PNC Machine BT30 Vertical Machining Center Cutting results in S45C. The WX-ST-PNC was able to stably process 1,000 holes with minimal changes in the effective diameter. Machining Data
Cutting Data Long tool life when high-speed machining hardened steels! Tool Work Material Cutting Speed Feed Internal Thread Size Drill Hole Size Threading Length Machining Method Coolant Machine WXO-ST-PNC 9.526.3P1.75 SCM440 40HRC 100m/min 3,351min -1 349mm/min 0.1mm/t M121.75 10.3 20mm 2 Down Cut 2 passes 10 Water-Soluble (10%) (Internal) BT40 Vertical Machining Center WXO-ST-PNC Number of processed thread holes 200 400 600 800 1,000 1,200 1,105 Holes Machined continuously without making tool diameter corrections. Gauge-Out In this example, even when high-speed machining at 100m/min with internally supplied coolant, there was no chipping and long tool life was achieved. The internal threadspitch diameter measurement was stable, demonstrating the effectiveness of this tool in mass production machining. Pitch diameter of internal thread +0.15 +0.10 +0.05 0 0 Number of processed thread holespitch dia. (mm) WXO-ST-PNC 200 400 600 800 1,000 1,200 Changes in the extent of wear on the outer circumference (mm) 0.2 0.15 Number of processed thread holeswidth of Wear 0.1 0.05 WXO-ST-PNC 700 Holes 0 200 400 600 800 1,000 1,200 1,100 Holes Normal Wear 40% Stable machining in stainless steels! Wear is 40% less than the competitor. Tool Work Material Cutting Speed Feed Internal Thread Size Threading Length Coolant Machine WXO-ST-PNC 9.526.6P1.75 SUS304 80m/min 2,681min -1 168mm/min 0.06mm/t M121.75 23mm Water-Soluble BT40 Vertical Machining Center Even when machining stainless steel at 80m/min, it was possible to machine over 1,500 holes, and tool wear was 40% less than the competitors product. Low wear, slow wear progression and long, stable machining of internal threads were achieved. WXO-ST-PNC Competitor WXO-ST-PNC Number of processed thread holes 500 1,000 1,500 1,500 Holes 1,500 Holes Still Running Still Running Changes in the extent of wear on the outer circumference
WX-PNC!! In non-ferrous materials, WX-PNC has excellent durability Tool Work Material Cutting Speed Feed Internal Thread Size WX-PNC 7.614.3 U16 A7075 160m/min 6,701min -1 650mm/min 0.16mm/t 3/8-16UNC WX-PNC Number of processed thread holes 2,000 4,000 6,000 8,000 8,800 Holes 8,800 Holes Still Running Still Running Threading Length 12mm Coolant Water-Soluble Machine BT40 Vertical Machining Center Even after machining 8,800 holes in A7075 with a cutting speed of 160m/min, tool wear was negligible. It was still possible for the WX-PNC to continue much more, effectively achieving stable machining of internal threads on a machining center. No.1 (after cutting 8,800 threads) No.2 (after cutting 8,800 threads) WX-PNC 7182 The WX-PNC is also for heat-resistant steels. It achieved twice the tool life of the competitor in Inconel 718 Tool Work Material Internal Thread Size Threading Length 1 Feed Per Tooth Coolant Machine WX-PNC 4.5510.2 U20 718 43HRC Inconel 718 1/4-20UNC 9mm 0.03mm/t 10 Water-Soluble (10%) BT40 Horizontal Machining Center These are the test results in Inconel 718 at various cutting speeds. At cutting speeds under 50m/min, durability is better and this seems to be an effective machining range. The WX-PNC achieves twice the tool life of the competitor, no matter the cutting speed. Cutting Speed and Durability Count WX-PNC Machining Data
Cutting Data 80% Reground tools have 80% the tool life of new tools Tool Work Material Cutting Speed Feed Internal Thread Size Drill Hole Size Threading Length Coolant Lubricant Supply Machine OT-SFT-PNGT 1230 P1.5 S45C 90HRB 70m/min 1,857min -1 130mm/min 0.07mm/t M161.5 14.520mm 20mm Water-Soluble 7MPa Collet Through BT40 Horizontal Machining Center Number of processed thread holes 500 1,000 This is the test result without adjusting tool's diameter. Effective Diameter at Early Stage Effective Diameter at End of Tool Life New tool 1,170 Holes 120m 80m Reground no coating on flutes Too big taper 847 Holes Gauge-Out 120m 80m Here are the results of a durability comparison without cutter compensation between new tools and reground tools (without recoating). Even without coating on the flutes, the reground tools were able to get 80% of the tool life of new tools. It is clear that regrinding can even further contribute to cost reductions. In small diameters, Carbide Planet Cutters are effective Tool Work Material Cutting Speed Feed Internal Thread Size Drill Hole Size Threading Length Coolant Machine OT-PNGT 4.512 P1 S45CSS400 50m/min 3,536min -1 80mm/min 0.03mm/t M61 515mm Blind 9mm Non-Water-Soluble BT40 Horizontal Machining Center JIS 2 / previous JIS class2pitch dia. (m) 200 150 100 50 0 ISOJIS6H / ISOJISclass6 500 1,000 1,500 2,000 2,500 2,800 Number of processed thread holes Hole Entry far area After threading 2,800 holes, the level of wear was still minimal. Because of tool rigidity issues, thread mill for HSS are only suitable for sizes larger than M14, but carbide tools are ideal for small diameter internal thread milling. Please make sure that the variance between entrance, inside and pitch diameter is kept to a minimum during machining. Pitch dia. (m) 200 150 100 50 ISOJIS6H / ISOJISclass6 JIS 2 / previous JIS class2 Hole Entry far area 0 1,000 2,000 3,000 4,000 5,000 6,000 Number of processed thread holes Produced excellent surface finish and displayed high endurance (6,516 holes).
For machining taper pipe threads, Planet Cutters exceed the limits of taps Tool Work Material PNGT AC4C-F Tool Size PNGT 1225Rc14 HSS-Co 4F Taper tap PT 3/4 HSS Drill Hole Size 2320mm Through Cutting Speed 70m/min 2,073min -1 8.3m/min100min -1 Threading Length 20mm Feed 431mm/min0.09mm/t 172mm/min Coolant Water-Soluble Surface Finish 4.8mRy 5mRy 6.2mRy 7.5mRy Machine BT40 Horizontal Machining Center Threading Time 7/ (second/hole) 25/ (second/hole) One of the known issues in hole machining is out of roundness, but the planetary motion of thread mill helps to eliminate this. Please note the difference in roundness. An additional advantage is the reduction in machining time by 1/3. However, depending on the workpiece, this may not be the limit. Tool Work Material Cutting Speed Feed drilling threading Threading Time Coolant Machine DR-O-PNAC M81.25-2D AC4B-F 250m/min 12,243min -1 2,449mm/min 0.2mm/rev 413mm/min 0.09mm/t 3.4 second/hole 10 Water-Soluble (10%) BT40 Horizontal Machining Center As this example shows, the Super Planet with internal coolant was able to completely drill, chamfer and tap in 3.4 seconds. Please make sure that in addition to being able to clear the machining centers tool posts, that tools are able to satisfactorily support high efficiency machining. (Use is restricted to the appropriate work materials) Circularity JIS 2 / previous JIS class2 Pitch dia. 0.04mm Super high speed multifunction tool application (m) 200 150 100 50 0 5,000 10,000 15,000 20,000 0.12mm ISOJIS6H Number of processed thread holes Hole Entry far area Still Running Machining Data
Cutting Data BT40M261.5 300 On a BT40 machine, an M26x1.5 internal thread was achieved. Machining over 300 holes with one side of an insert was possible. Tool Size Body Work Material Insert Cutting Speed Feed Internal Thread Size Drill Hole Size Threading Length Coolant Coolant Supply Machine HY-PRO P Multi-Point TMC20-3 3 1.5 SO TM2 S45C (91 92.5HRB) 200m/min 3,185min -1 92mm/min 0.125mm/t M261.5 24.520mm Through 12mm 10 Water-Soluble Chlorine-Free (10%) Internal + External BT40 Horizontal Machining Center HY-PRO P Multi-Point Number of processed thread holes 100 200 300 306 Holes Gauge-Out On a BT40 machine, an M26x1.5 internal thread was achieved. In spite of being a large diameter thread, it was possible to machine 300 holes with one insert side, and over 600 holes with both sides. This provides equal or greater economy than standard cutting taps. BT40M1204.5 M120x4.5 threads can be machined on a BT40 machine. And the surface finish of the internal threads is excellent! Tool Size Arbor Body Work Material Insert Cutting Speed Feed Internal Thread Size Drill Hole Size Threading Length Overhang Length Coolant Machine HY-PRO P Multi-Point TMSH-D100-FMA31.75-5 5 4.5 SO TM2 BT40-FMA31.75-45 S50C 180m/min 573min -1 201mm/min0.3mm/t M1204.5 115.525mm Through 20mm 93mm 10 Water-Soluble Chlorine-Free (10%)(External) BT40 Horizontal Machining Center Superior finished surface of the internal thread Normal wear of insert threads Large threads that are usually restricted by the machine when standard tapping can be machined on a BT40 machine. This example clearly demonstrates the benefits of thread mills.
P=4 Large-pitch internal threads are machined in a stable manner! (P=4 internal threads are machined in a single pass in carbon steel) Tool Size Body Work Material Insert Cutting Speed Feed Internal Thread Size Drill Hole Size Threading Length Overhang Length Cutting Method Coolant Machine HY-PRO P Single-Point TM4SC 25C31-115-2U 2UDC60 TM S50C 150m/min 1,540min -1 213mm/min 0.25mm/t M364 32 Through 50mm 70mm 1 1 Pass Water-Soluble (External) BT50 Vertical Machining Center HY-PRO P Single Point Number of processed thread holes 10 10 Holes Machined continuously without making tool diameter corrections. Wear after 10 holes of machining Still Running With a single point, cutting resistance is low, suppressing variance in machined internal threads and guaranteeing precision. In this example, initial internal thread machining and initial chip performance are confirmed. Machining Data
Features of thread mills and hints for usage What is a thread mill? Thread mill is a tool designed to cut threads by milling. Operation Insert thread mill to the processing hole depth. Thread will move 1P toward Z axial per rotation. To finish, machine till the hole entry. Advantages of using thread mills A single tool can be used to cut threads in various sizes of diameters. A single tool can cut different threads such as M10 1.5, M12 1.5, and M16 1.5 if their pitch is the same. Cuts large-diameter threads with a low-power machine WX-PNC 1234.5 P1.5 Spiral fluted tap for general purpose M161.5 0 2 4 6 8 10 12 0.1 13 Nm The required torque is low compared with tapping, so thread mills can cut large-diameter threads with a low-power machine if the workpiece holding strength and mechanical rigidity are sufficiently high. Smooth handling of chips to reduce problems Thread mills break chips into small pieces and eject them smoothly, ensuring stable, problem-free thread cutting. Chips from WX-PNC Chip from a spiral fluted tap Thread mills are ideal for the following: High-precision taper pipe threading (no stop marks) Airtight threads by having no stop marks Thread cutting in drill holes with little allowance Thread milling cuts the thread closer to the bottom of a hole than tapping, leaving only one incomplete crest of thread. Stop Marks
Thread mills are used on numerically controlled machining centers that have simultaneous, triaxial control and helical interpolation functions. Track processing (aproach and release) Thread milling cutter Major dia. of internal thread Minor dia. of internal thread Step Function 1 2 Move to edge (maintain clearance). 2 3 Cut with helical milling. 3 4 360 Mill the circumference of the circle. 4 5 Pull away from edge. Top view of internal thread 5 6 Remove tool. Helical milling should be used during approach and release, as shown above, for machining precision and efficiency. Milling direction (up-cut and down-cut) Internal Thread Right-Hand direction of the tool's rotation direction of the tool's feed For an internal right-hand thread, up-cutrefers to cutting downward from the entrance of the hole, and down-cutrefers to cutting upward from the bottom of the hole, as shown in the illustration at left. (The cutting direction differs with rightand left-hand threads and the direction of the tools planet-like rotation.) Conventional Upcut Prioritize finished surface Climb (down) cut Prioritize tool rigidity For thread cutting in a blind hole with little allowance, feed the tool in the direction it is drawn out from the drill hole so as to avoid pressing chips into the bottom of the hole. Formula for calculating the feed rate of the thread mill series fz z n Dm Dc v f = mm/min Dm v f :mm/min Feed Dm :mm Actual Dia. Dc :mm Tool Dia. Note Internal External z fz n : Number of Flutes :mm/t Feed Rate :min 1 Speed On the arc cutting process for machining external and internal threads, the feed rate at the tool center can be obtained by multiplying the linear cut feed rate with a coefficient. The formulas for calculating coefficients vary between external- and internal-thread cutting. The formula Iisted left are for calculating the tool feed rates during arc-cutting, including calculating the coefficients to be used for multiplication with the linear-cut feed rate. References
FAQ about Thread Milling Q. Why cannot internal thread cutting tools be used to cut external threads? A. Metric and unified threads have different thread profiles between internal and external threads. For these threads, internal thread cutting tools cannot be used to cut external threads because in their basic thread profiles, the crest and root shapes are not uniform. However, for pipe threads, which have uniform crests and roots, thread cutting tools can be shared for internal and external thread cutting. Example basic thread profile (metric thread) Height of basic triangle Internal Thread External Thread Basic Height of Thread Compare the shapes of internal and external threads. 1/8 H 1/4 H Height cut off from crest: External Thread Internal Thread 1/4 H 1/8 H Height cut off at root: External Thread Internal Thread 5/8 H Both threads have the same basic height of thread (5/8H). However, their shapes are different from each other. Q. I used an indexable thread mill (HY-PRO Planet Cutter) to cut taper pipe threads. Why is there a height difference between the first and second cuts? A. Check the mounting surface of the insert. Taper pipe thread cutting inserts are tapered at an angle of 1 degree and 47 minutes. Mounting an insert with wrong side will result in a reverse taper. Use R-side on a right-hand body for cutting both right- and left-hand threads. Use a left-hand body only when you need to use the L-side of an insert. * For detailed information, see p. 38. Q. Can I use NC programs developed for a custom-made Thread Mill with ThreadPro? A. Yes, you can. Please consult our sales representatives. Q. What does "124/004" or "028/004", assigned to the body or insert of my HY-PRO Planet Cutter mean? A. They are model numbers and have no specific meaning. They were assigned for distinction purposes when coarse thread pitch tools were added to our lineup of fine thread pitch tools. These tools can be used to cut fine pitch threads in a limited range of sizes. For their applicability, use the compatibility chart and NC program development software ThreadPro.
Q. How should I choose an indexable insert body? A. Please refer to the tool selection guide on p. 25 and 26. Q. What does the number "75" under "Fit %" mean, which is displayed on the data entry screen of ThreadPro? A. It means where to aim at within the acceptable range of threads. Default values are 75% (larger side) for internal threads and 25% (smaller side) for external threads in light of their engagement. You can change these to your desired values. Narrowly acceptable on the larger side Narrowly acceptable on the smaller side 100% 75% 50% 25% 0% Q. I have difficulty understanding the working of the Thread Mill and/or cutting methods. A. Acceptable Accuracy of internal thread 75% of larger limit for internal threadaim here! Please visit OSG website to view our web-based workshop material. The material uses video and illustrations to provide easy-tounderstand descriptions. References What does aiming 75% fit mean?