P001.pdf

Size: px

Start display at page:

Download "P001.pdf"

たつやこやぎ
5 years ago
Views:

1 Before commencing assembly, please read these instructions thoroughly. R WINGSPAN : 600mm THE FINEST RADIO CONTROL MODELS For Intermediate & Advanced Flyers INSTRUCTION MANUAL RADIO CONTROLLED ELECTRIC POWERED THERMAL GLIDER SOARUS 600 INDEX REQUIRED FOR OPERATION BEFORE YOU BEGIN RADIO PREPARATION ASSEMBLY PARTS LIST OPERATING YOUR MODEL SAFELY SAFETY PRECAUTIONS This radio control model is not a toy. First-time builders should seek the advice of experienced modellers before commencing assembly and if they do not fully understand any part of the construction. Assemble this kit only in places out of children s reach! Take enough safety precautions prior to operating this model. You are responsible for this model s assembly and safe operation! Always keep this instruction manual ready at hand for quick reference, even after completing the assembly. Ni-Cd The product you have purchased is powered by a rechargeable battery. The battery is recyclable. At the end of its useful life, under various national / state and local laws, it may be illegal to dispose of this battery into the municipal waste stream. Check with your local solid waste officials for details in your area for recycling options or proper disposal. *SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE. No KYOSHO

2 No.77 KYOSHO CORPORATION JAPAN THE FINEST RADIO CONTROL MODELS R This model is designed for ch operation with Auto-cut-off or Electronic Speed Controller. REQUIRED FOR OPERATION (Not included in kit!) Ni-Cd Battery Ni-Cd Battery No.77 8.V-600mAh AE Ni-Cd Battery 8.V-600 mah AE Rechargeable Ni-Cd BATTERY This model will require a ch radio control (with standard servos and electric speed controller) for aircraft. If you use an auto-cut-off relay,no brake action is available so the propeller will not fold after motor cut-off occurs. CAUTION: Only use a radio for Airplanes! (Any other radio is prohibited!) Charger Charger (Snitable for your Ni-Cd Battery) No III Multi Charger III Transmitter with mixing function. Servo (Micro servos prefered) 8mm or smaller 9.7mm or smaller mm or smaller Servo (Micro servos prefered) 0mm or smaller AA-size Batteries (For Transmitter) AA Electronic Speed Controller for airplanes. ( No Brake Function ) No Sky Victory 0 Electronic Speed Conloller No V Auto cut-off relay (8.V) AA Extension Cord extension cord for aileron extension cord for elevator Y-Harness cord for aileron 5 Glue Epoxy Glue Tape Epoxy A Epoxy B 96 Foam Tape (5mm) for mounting the receiver & Electronic Speed Controller Tape mm or smaller 0mm or smaller TOOLS REQUIRED Sharp Hobby Knife Phillips Screwdriver (L.M.S) Awl Drill Solder Wire Cutters REAMER Scissors Solder Iron No.80 TAPER REAMER CAUTION: Handle tools carefully!

3 BEFORE YOU BEGIN Read through the manual before you begin, so you will have an overall idea of what to do. Symbols used throughout the instruction manual, mm Drill holes with the specified diameter (here: mm). Must be purchased separately! Pay close attention here! Ensure smooth non-binding movement while assembling. Check all parts. If you find any defective or missing parts, contact your local dealer or our Kyosho Distributor. Assemble in the specified order. Cut off excess. Do not overlook Assemble left and right sides this symbol! the same way. Tentatively tighten. The pre-covered film on ARF kits may wrin-kle due to variations of temperature. Smooth out as explained right. with cover (cloth) low setting Use an iron covered with a cloth! Start at low setting. Increase the set-- ting if necessary. If it is too high, you may damage the film. A new Ni-Cd battery must be charged before it is used. Refer to the charger instruction manual for charging. Ni-Cd BATTERY START RADIO PREPARATION FINISH 8 CHARGER DCV Set up the radio control system as indicated below Install batteries. (Transmitter) Extend the antenna. (Transmitter) Connect the Ni-Cd battery. Extend the antenna. (Receiver) Center the trims. Switch on. (Transmitter) Switch on. (Receiver) Make sure the servos are working. Install the grommets to the servo as shown. 9 0 Switch off. (Receiver) Switch off. (Transmitter) Retract the antenna. (Transmitter)

4 Fuselage Cut vent holes as shown. Use a sharp hobby knife and cut carefully not to peel gel-coat. 5 mm 5 mm mm 8 mm Folding Propeller x mm x mm Screw mm mm mm Nut x 8mm x 8mm TP TP Screw Front mm Set Screw x mm mm Moter.6 x 6mm F/H Screw Cross the grain of A and B parts. B A Motor B A.6mm.6 x 6mm.6mm Drill two holes to match the motor. mm mm Drill holes with the specified diameter (here: mm). Tentatively tighten. Ensure smooth non-binding movement while assembling. Pay close attention here!

5 Fuselage 8 mm 8 mm mm mm mm C C mm.mm mm 5 Wing One side only 7 mm 7 mm Mark. 6 Wing Cut away covering film only. mm mm.mm mm mm A=A' mm mm.mm A A' Pay close attention here! Assemble left and right sides the same way. mm mm Drill holes with the specified diameter (here: mm). 5

6 7 Fuselage.mm A=A' mm Blind Nut A A' Parallel with Fuselage. 8 Fuselage No use. D D I H F H I G E G F E Make sure to glue securely. If not properly glued, a faliure in flight may occur. I H G F E D 9 Tail Surfaces Cut away covering film only. mm mm Drill holes with the specified diameter (here: mm). Do not disregard this symbol! Pay close attention here! 6

7 0 Tail Surfaces Top 07-0 Make sure to glue securely. If not properly glued, a faliure in flight may occur. Cut away covering film only. A B B' A' A=A' B=B' C=C' C C' Be rough by sandpaper on setting surfase. Servo Included with the servo. Trim the holes to fit your servos. Servo Linkage mm 5 mm mm Rod Assemble in the specified order. Must be purchased separately! Pay close attention here! Assemble left and right sides the same way. Do not disregard this symbol! 7

8 Linkage x 0mm Screw x 0mm Linkage mm Set Screw 5mm Stopper Solder Make sure to solder securely. If not properly soldered, a faliure in flight may occur. mm Stopper 5 mm Included with the servo. 0mm Rod Elevator Servo 5 Linkage mm Nut mm Rudder Rod Cut off excess. Must be purchased separately! Assemble left and right sides the same way. Do not disregard this symbol! 8

9 6 Fuselage Tentatively tighten Make sure to glue securely. If not properly glued, a faliure in flight may occur..5 mm Securely install and fasten the propeller. If coming off while rotating, there is a high risk of serious injury! 7 Canopy x 6mm x 6mm TP TP Screw x 6mm 0.8mm x 6mm Decal.6mm mm.6mm mm 8 Velcro Tape Battery Apply epoxy glue on the boord. After dry, apply Velcro Tape. Velcro Tape Foam Tape Electronic Speed Controller or Auto cut-off relay. Receiver Must be purchased separately! Do not disregard this symbol! mm mm Drill holes with the specified diameter (here: mm). Assemble in the specified order. 9

10 9 Wing x 0mm Screw mm Nut mm Fix with Sticky Tape. Cut to fit your servos. Servo Double-sided Tape. Cut away covering film only. x 0mm Extension Cord Solder Make sure to solder securely. If not properly soldered, a faliure in flight may occur. Y-Harness Cord 0 Fuselage Do NOT under any circumstances cut the antenna-wire as this will reduce range and possibly cause the plane to crash! Antenna Wing x mm x mm F/H Screw Make certain wing securely attaches to fuse. erratic flight and/or crashes can result if it comes loose during flight. Must be purchased separately! Do not disregard this symbol! Assemble left and right sides the same way. 0

11 Decals For the correct placement of decals, please refer to the box top. CG / Angles Adjust the travel of each control surface to the values in the diagrams. These values fit general flight capabilities. Readjust according to your needs and flight level. Do not fly before confirming the correct location of the CG.If the CG is incorrect, you lose control of your airplane which leads to accidents! CG AILERON ELEVATOR 8 58mm 8 58mm Do not overlook this symbol! First-time fliers should seek advice for hints in pre-flight adjustments and assembly from experienced fliers. Be reminded that flying a badly assembled or badly adjusted aircraft is very dangerous! In the beginning, first-time fliers should always be assisted by an experienced flier and never fly alone! Due to the wing being very light-weight sudden maneuvers and violent aerobatics can cause it to break while in flight. This will result in a crash and possibily cause harm to the operator or nearby persons. Under no circumstances should violent aerobatics be attempted with this model airplane. PARTS No Part Names Canopy Plywood parts Decals x Set x Set Quantity :FOR JAPANESE MARKET ONLY. No. Part Names Quantity Motor Set Folding Propeller Set (D6xP) Folding Propeller (D6xP) 800

12 OPERATING YOUR MODEL SAFELY Before Flying Flying After Flying Cautions for Safety Before flying your airplane, ensure the airfield is spacious enough. Always fly it outdoors in safe areas with no debris or obstacles! Do not fly your airplane on days with strong winds or side winds. Always land your airplane into the wind. WIND Do not allow watching people to get too close to a rotating propeller. For proper radio handling, refer to its explanations. Ensure the spinner and propeller are securely installed. Ensure the main wing is securely installed. Unplug the Ni-Cd battery. Battery Disuse defective propellers as well as deformed spinners. If the airplane begins to operate by itself, somebody else is on your frequency. Do not attempt to operate it under such condition for you may lose of control of it. Move the sticks on your transmitter to ensure that all controls move according to your inputs and the way you adjusted them. Beware of spinning propellers! Switch off the transmitter. Batteries and chargers become hot. Do not allow flammable materials to come in contact with them. OFF BATTERY OFF ON Fully extend the antenna (transmitter). Switch on the transmitter. Check the radio batteries. Unplug the Ni-Cd battery when not in use. Never try to modify Ni-Cd battery. This is very dangerous. OFF ON ON Plug in the Ni-Cd battery. Battery Beware of spinning propellers! With some electronic speed controllers, the electric motor (propeller) start spinning as soon as the electronic speed controller is connected. Launch your airplane by hand into the wind. WIND If your airplane does not function correctly, land it at once and find out the reason. Battery Proper maintenance extends the life of your airplane. Only use genuine KYOSHO parts. Do not dispose of used Ni-Cd batteries, return them to the shop. Battery Do not dispose of Ni-Cd batteries in a fire. They will explode and release harmful materials. Battery TEL THE FINEST RADIO CONTROL MODELS PRINTED IN CHINA R

P001.pdf

P001.pdf Before commencing assembly, please read these instructions thoroughly. WINGSPAN : 195mm R THE FINEST RADIO CONTROL MODELS EP CESSNA 180 TRAINER INSTRUCTION MANUAL RADIO CONTROLLED ELECTRIC POWERED AIRCRAFT