p01.pdf

Size: px

Start display at page:

Download "p01.pdf"

もりよりみねむら
5 years ago
Views:

1 Before commencing assembly, please read these instructions thoroughly! WINGSPAN: 175mm For Intermediate & Advanced Flyers. INSTUCTION MANUAL ADIO CONTOLLED ENGINE POWEED ALL-BALSA ACOBATIC AICAFT GILES G-0 60 INDEX EQUIED FO OPEATION BEFOE YOU BEGIN ASSEMBLY SPAE PATS OPEATING YOU MODEL SAFELY 3 3~ SAFETY PECAUTIONS This radio control model is not a toy! First-time builders should seek the advice of experienced modellers before commencing assembly and if they do not fully understand any part of the construction. Assemble this kit only in places out of childrenõs reach! Take enough safety precautions prior to operating this model. You are responsible for this modelõs assembly and safe operation! Always keep this instruction manual ready at hand for quick reference, even after completing the assembly. *SPECIFICATIONS AE SUBJECT TO CHANGE WITHOUT NOTICE. 000 KYOSHO No

2 EQUIED FO OPEATION (Purchase separately!) CAUTION: For details concerning the equipment listed below (size, maker, etc.), check with your hobby shop. Shock Protecting Foam Fuel Tube 1 5x5 This model will require a minimum channel radio control (with 5 standard servos) for aircraft. CAUTION: Only use radio control systems designed for aircraft. A minimum channel radio control system for aircraft. 1 1 AA-size Batteries, either dry cell or NiCd. AA AA xtension Lead x AA 5 equired for engine starting: Model Glow Fuel. MODEL ENGINE FUEL Fuel Bottle Plug Wrench WANING: Never use petrol / gasoline with glow engines. One-touch Plug Heater Set Y- Harness x 1 ead instruction manual supplied with radio control system thoroughly before use. 6 Glue Instant Glue Epoxy Glue (30 minutes type) Engine and Muffler Model Aircraft Engine Glow Plug 6 ~ ~ 90 Stroke.6 ~.60 Stroke.70 ~.90 Muffler 7 Silicon Glue Linkage Parts SILICON Epoxy A Epoxy B Please use stronge control horns and pushlods intended for large sized models. Muffler Adapter 8 Other equipment for enhancing airplane operation & performance Engine Starter 1V Battery (for starter) 3 Propeller and Spinner Propeller Purchase a propeller that will match your engine. 6mm Spinner 6mm Fuel Filter TOOLS EQUIED (Purchase separately!) Hobby Knife Phillips Screwdriver (L, M, S) Awl Needle Nose Pliers Scissors Wire Cutters

3 BEFOE YOU BEGIN 1 ead through the manual before you begin, so you will have an overall idea of what to do. Check all parts. If you find any defective or missing parts, contact your local dealer or our Kyosho Distributor. 3 Symbols used throughout this instruction manual, comprise the following: Apply epoxy glue. Apply instant glue (CA glue, super glue). Assemble left and right sides the same way. mm mm Drill holes with the specified diameter (here: mm). Cut off shaded portion. Must be purchased separately! Cut off excess. Ensure smooth non-binding movement while assembling. Pay close attention here! Do not overlook this symbol! Warning! The pre-covered film on AF kits may wrin-kle due to variations of temperature. Smooth out as explained right. with cover (cloth) low setting Use an iron covered with a cloth! Start at low setting. Increase the set-- ting if necessary. If it is too high, you may damage the film. ASSEMBLY 1 Main Wing Align the center line of main wing with aileron. Hole for servo connector. Before cutting away the covering film, lightly heat that area with an iron. Secure aileron hinges with instant glue, being careful not to glue the wing and aileron together. Cut off shaded portion. Apply epoxy glue. Apply instant glue (CA glue, super glue). Ensure smooth non-binding movement while assembling. Assemble left and right sides the same way. 3

4 Main Wing Main wing underside Hole for servo connector. Before cutting away the covering film, lightly heat that area with an iron. 3 Main Wing Warning! Securely glue together. If coming off during flights, you lose control of your airplane which leads to accidents! Top Note the direction. Top If there is a gap, carefully fill with epoxy glue. 0mm Main wing underside Main Wing Glass Fiber Tape Cut away film only. Cut off shaded portion. Assemble left and right sides the same way. Apply epoxy glue. Pay close attention here!

5 Main Wing Aileron servo extension cord Tape Included with the radio set. Aileron servo Front Cut the mount to fit your servo. Front 5 Main Wing 1 Adjust the travel of each control surface. Please refer to section 1. 6 Main Wing mm Align with main wing holes. Cut away film only. Apply epoxy glue. Assemble left and right sides the same way. Must be purchased separately! Cut off shaded portion. mm mm Drill holes with the specified diameter (here: mm). Pay close attention here! 5

6 7 Main Landing Gear 3mm 3 x 10mm TP Screw x 10mm TP Screw 3mm Set Screw L Stopper (L) 6mm 1mm 6mm 6 x 35mm x 10mm 3 x 10mm 6mm Nut mm 6x 35mm Screw Stopper (L) Attach gearpant and wheel to leg using parts provided making certain wheel rotates freely. 8 Engine Mount x 5mm Cap Screw Mark. Left mm Washer ight Mark mm Nut x 5mm Note the direction. Mark Mark ight mm.mm 133mm Left mm Assemble left and right sides the same way. Ensure smooth non-binding movement while assembling. mm mm Drill holes with the specified diameter (here: mm). Pay close attention here! 6

7 9 Engine Mount x 0mm Cap Screw In case of stroke engine. Drill the hole for Throttle od. Align the mark on both mounts with the mark on the fuselage. mm Mount Nut x 0mm Mark 5mm mm Mount Nut Tail Pipe Align the crankshaft of the engine with the side line. Throttle od Side Line Be sure the muffler will fit before mounting the engine. In case of stroke engine. Mark mm Mount Nut Align the mark on both mounts with the mark on the fuselage. x 0mm Tail Pipe Be sure the muffler will fit before mounting the engine. 5mm Side Line Use a muffler extension adapter. (Purchase separately) Drill the hole for Throttle od. Align the crankshaft of the engine with the side line. 10 Fuel Tank Silicone Tube mm mm Drill holes with the specified diameter (here: mm). Pay close attention here! Apply epoxy glue. Must be purchased separately! 7

8 11 Cowling x 10mm 1mm x 10mm TP TP Screw 5 mm elieve the cowl to clear the engine head. 3~mm 1 Main Wing Undercover x 30mm Cap Screw mm Washer Cut away only the film. x 30mm Warning! Securely attach the Main Wing. If the wing separates during flight, you will lose control of your airplane. Cut away film only. mm Mount Nut mm Cut away only the film. mm Mount Nut A AÕ A = AÕ x30mm Make certain the plane is aligned accurately per the diagram. A mis-aligned plane can fly erratically and cause accidents. Apply epoxy glue. Cut off shaded portion. mm mm Drill holes with the specified diameter (here: mm). Apply instant glue (CA glue, super glue). 8

9 13 Vertical / Horizontal Tail B BÕ Warning! Securely glue together. If the wing separates during flight, you will lose control of your airplane. A AÕ Cut away film only. A = AÕ B = BÕ C = CÕ D = DÕ Cut away film only. C CÕ D DÕ Feel for the edges of the holes underneath the film. Then, cut away the film along the edges. 1 Vertical / Horizontal Tail x 10mm TP Screw Warning! Securely glue together. If the wing separates during flight, you will lose control of your airplane. 3mm Set Screw 1 Stopper (S) 1 mm x 10mm 3mm Stopper (S) Apply epoxy glue. Assemble left and right sides the same way. Ensure smooth non-binding movement while assembling. Cut off shaded portion. mm mm Drill holes with the specified diameter (here: mm). Pay close attention here! 9

10 15 Vertical / Horizontal Tail 16 Canopy x 6mm x 6mm TP TP Screw 6 You can also attach the canopy without screws, using silicon glue. mm Silver Decal mm 10mm Cut off 1mm Apply instant glue into the screw hole as a reinforcement. 17 Throttle od Throttle od Included with the radio set. Throttle Servo Assemble left and right sides the same way. Ensure smooth non-binding movement while assembling. mm mm Drill holes with the specified diameter (here: mm). Must be purchased separately! Apply instant glue (CA glue, super glue). 10

11 18 udder od udder od udder Servo un the throttle linkage to suit your engine. Make certain the linkage is strong and secure. educe play to a minimum for best perfpormance. 19 Elevator od Elevator Servo Elevator od un the throttle linkage to suit your engine. Make certain the linkage is strong and secure. educe play to a minimum for best perfpormance. 0 Linkage Bottom View udder Servo Elevator Servo udder od Throttle Servo Elevator od Apply instant glue (CA glue, super glue). Must be purchased separately! Apply epoxy glue. mm mm Drill holes with the specified diameter (here: mm). Pay close attention here! 11

12 1 Linkage View From Underside Cut away the hole for pushrods. Elevator Pushrod udder Pushrod 3 Adjust the travel of each control surface. Please refer to section 3. Elevator Pushrod udder Pushrod adio Equipment Secure foam padding with rubber bands or tape as required. Carefully install the receiver and battery pack to ensure that they will not move during flight. Shock Protecting Foam CG 85100mm Never fly before checking the CGÕs required position. Move the location of the receiver and battery pack as needed to obtain the specified CG. 3 Adjust the travel of each control surface to the values in the diagrams. These values fit general flight capabilities. Position for right diagram. UDDE 35mm 35mm Position for right diagram. ELEVATO DOWN 15mm UP 15mm AILEON Position for right diagram. 1mm 1mm Must be purchased separately! Pay close attention here! 1

13 ESCUE ESCUE CAUTION ENGINE HEAD ESCUE ESCUE No GILES G0-60 PINTED IN CHINA Decal The box art and below picture can be used for the placement of the decals. (Some decals are not included.) CAUTION ENGINE HEAD ALL-BALSA AEOBATIC AICAFT ALL-BALSA AEOBATIC AICAFT Warning! 6~ This model aircraft is designed for Intermediate to Experienced fliers. Beginners should seek advice for pre-flight adjustments and assembly from more experienced fliers. Be aware that flying a badly assembled or badly adjusted aircraft is very dangerous! At the start, first-time fliers should always be assisted by an experienced flier and NEVE fly alone! This model aircraft is designed to be powered by either a stroke.6 ~.60 size engine or a stroke.70 ~.90 size engine. Installing a more powerful engine than specified or flying this model dangerously could lead to serious injury and/or damage to property. This model is desingned for sports stant. This model is not suited for modification such as retractable wheel or tuned silencer. Do not overlook this symbol! Warning! PATS No. Part Names Cowling Canopy Main Gear Quantity No Part Names Wheel Cover Decal for G0 :FO JAPANESE MAKET ONLY. Quantity (L.)

14 Direct-Mail-Parts-Order-System" is available only for Japanese market "Kyosho (1) (3) () 1, ,680 () (1) ()

15 11905 GILES G-0 60 The servise mentioned below is available only for Japanese market.

16 Warning! FLIGHT MANUAL Non-observance of this information could lead to serious injury and/or damage to property. Pre-Flight Checks Flying After Flying Safety Precautions Only fly model aeroplanes in areas away from houses and places where people gather. The weight and speed of your aeroplane make it a potential hazard. Make sure that the area around you is clear. For radio equipment, refer to the instruction manual included with your set. Check that the spinner and the propeller are securely fastened. If the model begins to operate by itself, there is another transmitter operating on your frequency. Do not try to operate your model if this happens, but change your transmitter and receiver crystals to another frequency. OFF ON Fully extend transmitter aerial. Switch on the transmitter. ON Switch on the receiver. ON Do not fly your aeroplane if it is a windy day or there are strong cross winds. Fill the fuel tank. By moving the various transmitter controls, ensure that all control surfaces move the way you intend them to. To start the engine, set low throttle on the transmitter and hold the engine starter against the spinner. Switch on engine starter. Adjust the throttle needle. Move the throttle control stick on the transmitter and check that the carburettor opens and closes easily. Always land your airplane into the wind. WIND Bring your airplane to a halt by lowering the engine control trim. After each flight, the engine is hot. Beware of getting burned. Switch off the receiver. OFF ON OFF Switch off the transmitter. OFF Draw the remaining fuel out of the tank and fill it back into the can. Wipe up any fuel deposits or dirt. Always regulate the engine from behind, but never from infront or from the sides, because a rotating propeller might badly injure you. Do not allow watching people to get too close to a rotating propeller. Immediately disuse defective propellers as well as deformed spinners. If the batteries of the radio system are flat, replace them with new ones. Do not fly your airplane above people standing around. Check that the wings are properly and firmly affixed. Launch the aeroplane into the wind. WIND Only use KYOSHO genuine parts. Never throw burning, gleaming or smouldering things into fuel cans, even if these happen to be empty. This could result in serious injury TEL () 10:00~18: PINTED IN CHINA

P001.pdf

P001.pdf Before commencing assembly, please read these instructions thoroughly. WINGSPAN : 195mm R THE FINEST RADIO CONTROL MODELS EP CESSNA 180 TRAINER INSTRUCTION MANUAL RADIO CONTROLLED ELECTRIC POWERED AIRCRAFT