p01.pdf

Size: px

Start display at page:

Download "p01.pdf"

こうごえいさか
5 years ago
Views:

1 Before commencing assembly, please read these instructions thoroughly! R THE FINEST RADIO CONTROL MODELS For Intermediate & Advanced flyers. WINGSPAN: 1475mm INSTRUCTION MANUAL RADIO CONTROLLED ENGINE POWERED ALL-BALSA ACROBATIC AIRCRAFT CAP BREITLING INDEX REQUIRED FOR OPERATION BEFORE YOU BEGIN ASSEMBLY OPTIONAL PARTS OPERATING YOUR MODEL SAFELY 3 3~ ~1 SAFETY PRECAUTIONS This radio control model is not a toy! First-time builders should seek the advice of experienced modellers before commencing assembly and if they do not fully understand any part of the construction. Assemble this kit only in places out of childrenõs reach! Take enough safety precautions prior to operating this model. You are responsible for this modelõs assembly and safe operation! Always keep this instruction manual ready at hand for quick reference, even after completing the assembly. SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE. 000 KYOSHO No.1196

2 1 REQUIRED FOR OPERATION (Purchase separately!) CAUTION: For details concerning the equipment listed below (size, maker, etc.), check with your hobby shop. 4 5 A minimum 4 channel radio for airplanes (with 5 standard servos), and nicad or alkaline batteries are required. CAUTION: Only use a minimum 4 channel radio for aircraft! (No other radio may be used!) 5 Required for engine starting: Glow engine fuel only. MODEL ENGINE FUEL Fuel Primer WARNING: Normal gasoline cannot be used with glow engines. One-touch Plug Heater Set 4 A minimum 4 channel transmitter for aircraft.with 5 servos. Plug Wrench aileron extension cords 1 1 Y- harness 6 Glue Instant Glue 30 Epoxy Glue (30 minutes type) For handling the radio properly, refer to its instruction manual. Engine and Muffler Model Airplane Engine 3 4 Glow Plug Propeller and Spinner Purchase a propeller that will match your engine. Sponge Sheet stroke stroke Propeller Fuel line Muffler 7 8 Silicon Glue Linkage Parts SILICON Epoxy A Epoxy B Please use stronge control horns and pushlods intended for large sized models. Other equipment for enhancing airplane operation & performance Engine Starter Fuel Filter 1V 1V Battery (for starter) Spinner(6mm TOOLS REQUIRED (Purchase separately!) Sharp Hobby Knife Needle Nose Pliers Scissors Wire Cutters Awl Phillips Screwdriver (L, M, S) Drill,Tap,Handgrinder

3 BEFORE YOU BEGIN 1 Read through the manual before you begin, so you will have an overall idea of what to do. Check all parts. If you find any defective or missing parts, contact your local dealer or our Kyosho Distributor. 3 Changes in weather may cause the covering film to slacken.if necessary,use a heat gun or iron to tighten the covering. 4 You can keep the covering film from wrinkling or peeling by spraying the plane with clear polyurethane. 5 Symbols used throughout this instruction manual, comprise: Apply epoxy glue. Apply instant glue (CA glue, super glue). Assemble left and right sides the same way. mm mm Drill holes with the specified diameter (here: mm). Cut off shaded portion. Must be purchased separately! Cut off excess. Ensure smooth non-binding movement while assembling. Pay close attention here! Do not overlook this symbol! The pre-covered film on ARF kits may wrin-kle due to variations of temperature. Smooth out as explained with cover (cloth) low setting Use an iron covered with a cloth! Start at low setting. Increase the set-- ting if necessary. If it is too high, you may damage the film. 1 Main Wing ASSEMBLY Tow kinds of hinges are used on each surface, Make sure only epoxy is used on the metal hinges and only CA glue is used on the nylon hinges. Metal Hinge Secure metal hinges with epoxy being careful to avoid geting glue in the hinge pin areas. Nylon hinge Secure nylon hinges with instant glue, being careful not to glue the wing and aileron together. Make certain the hinges are adequately secured with glue.if they come loose in flight accidents may result. Align the center line of main wing with aileron. 3

Main Wing(Botton view) Make certain linkages are strong and secure.reduce play to a minimum for best peformance.

if they come off during flight yoo will lose control of yoor aircraft! 3 Top view.

Top Use epoxy glue to fill the opening. Dihedral. 55mm Cut away covering film only in these locations.

4 Main Wing(Botton view) Make certain linkages are strong and secure.reduce play to a minimum for best peformance. Cut the mount to fit your servo. Aileron Servo Set all screws securely.if they come off during flight yoo will lose control of yoor aircraft! 3 Top view. Main Wing Ensure that the two wing halves are securety glued together with epoxy. Note the direction. Top Use epoxy glue to fill the opening. Dihedral. 55mm Cut away covering film only in these locations. Main wing underside 4 Top view Main Wing Cut away film only here. Bottom view When cutting the film coverring,do not cut too deeply to avoid weakening The wood structure beneath. Apply epoxy glue. Must be purchased separately! Cut off shaded portion. Do not disregard this symbol! Assemble left and right sides the same way. Pay close attention here! 4

5 Main Wing 4 x 40mm Screw Washer Bottom view 4 x 40mm 4.

erratic flight and/or crashes can result if it comes loose during

5mm Depends on the position of carburettor.

Use the mufller adapter for clear the mufller to cowling.

Throttle Rod Position the engine so the fit the mufller exits the fuse

5 5 Main Wing 4 x 40mm Screw Washer Bottom view 4 x 40mm 4.mm A AÕ A = AÕ Make certain wing securely attaches to fuse. erratic flight and/or crashes can result if it comes loose during flight. 6 Engine Mount 4 x 0mm Screw Mount Nut 4 4 4x0mm 5mm A/ A/ 3.5mm Depends on the position of carburettor. A When using a stroke engine. Use the mufller adapter for clear the mufller to cowling. 4 When using a 4stroke engine. Throttle Rod Position the engine so the fit the mufller exits the fuse and the engine shaft is centered on the firewall as shown. Apply epoxy glue. mm mm Drill holes with the specified diameter (here: mm). Do not disregard this symbol! Must be purchased separately! Pay close attention here! 5

7 Fuel tank 3 x 5mm TP TP Screw 1 Fix tank in fuselage with

35mm 5mm Sillicon tube 8 Engine Mount 4 x 5mm Cap Screw Spring

6 7 Fuel tank 3 x 5mm TP TP Screw 1 Fix tank in fuselage with silicon glue. After confirming the posi-tion of the fule tank's internal parts(see front view), insert and tighten the screw. 35mm 5mm Sillicon tube 8 Engine Mount 4 x 5mm Cap Screw Spring Washer Washer Nut mm Spring Washer Washer Nut 4x5mm Engine Mount mm mm Drill holes with the specified diameter (here: mm). 6

9 Vertical/Horizontal Tail When cutting the film coverring, Do not cut toodeeply to avoid weakening The wood

C CÕ Make certain plane is aligned accurately per the diagram. A mis-aligned plane can fly erraticaliy and cause accidents.

Being careful not to glue the fin and rudder together. Secure metalhinges with epoxy.

Make certain parts are aligned accurately and play is reduced to a minimum. L Apply epoxy glue.

7 9 Vertical/Horizontal Tail When cutting the film coverring, Do not cut toodeeply to avoid weakening The wood structurebeneath. A BÕ B AÕ Cut away only covering film. A = AÕ B = BÕ C = CÕ Cut away only covering film. C CÕ Make certain plane is aligned accurately per the diagram. A mis-aligned plane can fly erraticaliy and cause accidents. 10 Horizontal / Vertical Tail Bend at end of rod..6 x 8mm TP TP Screw mm.6 x 8mm mm Secure nylonhinges with instant glue. Being careful not to glue the fin and rudder together. Secure metalhinges with epoxy. Being careful to avoid getting glue in the hingepin areas. Make certain parts are aligned accurately and play is reduced to a minimum. L Apply epoxy glue. Ensure smooth non-binding movement while assembling. Apply instant glue (CA glue, super glue). mm Drill holes with the specified Cut off shaded portion. mm diameter (here: mm). Pay close attention here! L Assemble left and right sides the same way. Do not disregard this symbol! 7

1 Linkage Make certain linkages are strong and secure. Reduce play to a minimum for best performance.

8 11 Main Landing Gear. 4 x 40mm Screw Washer 416mm Spring washer Nut 6 4 x 16mm Screw Attach gearpant and wheel to leg using parts provided making certain wheel rotates freely. 1 Linkage Make certain linkages are strong and secure. Reduce play to a minimum for best performance. Receiver Rudder Servo Elevator Servo Throttle Servo Linkage lod Make certain parts are alignedaccurately and play is reduced to a minimum. Tighten screwssecurely. Must be purchased separately! Ensure smooth non-binding movement while assembling. Do not disregard this symbol! Drill holes with the specified diameter (here: mm). Pay close attention here! 8

13 Linkage Make certain linkages are strong and secure.

Linkage lod Rudder Horn Elevator Horn Make certain parts are

Relive the cowl to clear the mufller. L Cut away film only.

9 13 Linkage Make certain linkages are strong and secure. Reduce play to a minimum for best performance. Linkage lod Rudder Horn Elevator Horn Make certain parts are aligned accurately and play is reduced to a minimum. Tighten screws securely. 14 Couling.6 x 8mm TP TP Screw 4 Relive the cowl to clear the engine hed. Relive the cowl to clear the mufller. L Cut away film only. mmmm 3mm mm mm Must be purchased separately! Apply epoxy glue. mm Cut off shaded portion. mm Drill holes with the specified diameter (here: mm). L Assemble left and right sides the same way. Pay close attention here! Do not disregard this symbol! 9

10 15 Canopy Color paint x 8mm TP TP Screw 4 Color paint.

included decals. For the correct placement of decals, please refer to box top.

10 10 15 Canopy Color paint x 8mm TP TP Screw 4 Color paint.6 x 8mm mm 16 Adjust the travel of each control surface to the values in the diagrams. Reference point for diagram at right. RUDDER mm mm CG 6575mm AILERON 11mm 11mm Reference point for diagram at right. ELEVATOR Reference point for diagram at right. DOWN UP 17mm 17mm 17 Decal Apply included decals. For the correct placement of decals, please refer to box top. Cut off shaded portion. mm mm pecified diameter (here: mm). Must be purchased separately! Pay close attention here!

11 This aircraft is for intermediate to advanced builders and flyers only. Biginners connot fly and building this aircraft. This aircraft has been flight tested with snap-rolls and other aerobatic maneuvers.however,repeated violent maneuvers may overstress the airframe. Please fly in a way that will not otherstress the airframe. Repeated flyng can cause stress cracks to appear in the wood and joints, please inspect after each flight. If any abnormalities are noted, repair immediately befor the next flight to avoid accsidents. Glue joints can loosen even thoogh they appear to be tight. If you notice irregular flight, investigate the cause and repair it befor the next flight. This aircraft is designed for stroke or 4 stroke sized engines only. Using larger,more powerful engens is not safe and may result in airframe failure.do not exceed the recommended engine size or engage in extreme aerobatic maneuvers. Do not overlook this symbol! No. Part Names Cowling Canopy Main Gear 1 Quantity PARTS No. Part Names (R) (L) Wheel Pants Decale 000 FOR JAPANESE MARKET ONLY. Quantity (R) 1,(L)1 (a),(b),(c) No. Part Names mm Duraluminium Spinner 6mm mm Nylon Spinner (White) 6mm mm Nylon Spinner (Red) 6mm mm Nylon Spinner (Yellow) 6mm SPOS7010 SP Adapter Nut O.S..70~ SPOS6310 SP Adapter Nut YS.63~ PP Fuel Tube Stopper OPTIONAL PARTS No FOR JAPANESE MARKET ONLY. Part Names 60mm Sponge Tire 60mm 5mm Sponge Tire 5mm, Tail Gear Assy 400cc Fuel Tank 400cc

12 Direct-Mail-Parts-Order-System" is available only for Japanese market "Kyosho (1) (3) () 1, ,680 (4) (1) ()

13 1196 CAP 3-60 BREITLING The servise mentioned below is available only for Japanese market.

14 FLIGHT MANUAL Non-observance of this information could lead to serious injury and/or damage to property. Pre-Flight Checks Flying After Flying Safety Precautions Only fly model aeroplanes in areas away from houses and places where people gather. The weight and speed of your aeroplane make it a potential hazard. Make sure that the area around you is clear. For radio equipment, refer to the instruction manual included with your set. Check that the spinner and the propeller are securely fastened. If the model begins to operate by itself, there is another transmitter operating on your frequency. Do not try to operate your model if this happens, but change your transmitter and receiver crystals to another frequency. OFF ON Fully extend transmitter aerial. Switch on the transmitter. ON Switch on the receiver. ON Do not fly your aeroplane if it is a windy day or there are strong cross winds. Fill the fuel tank. By moving the various transmitter controls, ensure that all control surfaces move the way you intend them to. To start the engine, set low throttle on the transmitter and hold the engine starter against the spinner. Switch on engine starter. Adjust the throttle needle. Move the throttle control stick on the transmitter and check that the carburettor opens and closes easily. Always land your airplane into the wind. WIND Bring your airplane to a halt by lowering the engine control trim. After each flight, the engine is hot. Beware of getting burned. Switch off the receiver. OFF ON OFF Switch off the transmitter. OFF Draw the remaining fuel out of the tank and fill it back into the can. Wipe up any fuel deposits or dirt. Always regulate the engine from behind, but never from infront or from the sides, because a rotating propeller might badly injure you. Do not allow watching people to get too close to a rotating propeller. Immediately disuse defective propellers as well as deformed spinners. If the batteries of the radio system are flat, replace them with new ones. Do not fly your airplane above people standing around. Check that the wings are properly and firmly affixed. Launch the aeroplane into the wind. WIND Only use KYOSHO genuine parts. Never throw burning, gleaming or smouldering things into fuel cans, even if these happen to be empty. This could result in serious injury TEL () 10:00~18: THE FINEST RADIO CONTROL MODELS PRINTED IN CHINA R

p01.pdf

p01.pdf Before commencing assembly, please read these instructions thoroughly. THE FINEST RADIO CONTROL MODELS R WINGSPAN: 575mm (6") For Advanced Flyers INSTRUCTION MANUAL RADIO CONTROLLED ENGINE POWERED SPORTS