p01.pdf

Size: px

Start display at page:

Download "p01.pdf"

たつやささおか
4 years ago
Views:

Before commencing assembly, please read these instructions thoroughly! WINGSPAN: 1375mm R THE FINEST RADIO CONTROL MODELS For Intermediate & Advanced Flyers.

1 Before commencing assembly, please read these instructions thoroughly! WINGSPAN: 1375mm R THE FINEST RADIO CONTROL MODELS For Intermediate & Advanced Flyers. INSTRUCTION MANUAL RADIO CONTROLLED ENGINE POWERED SCALE BIPLANE KYOSHO SUPER QUALITY SERIES REQUIRED FOR OPERATION BEFORE YOU BEGIN ASSEMBLY SPARE PARTS OPERATING YOUR MODEL SAFELY ~ SAFETY PRECAUTIONS This radio control model is not a toy! First-time builders should seek the advice of experienced modellers before commencing assembly and if they do not fully understand any part of the construction. Assemble this kit only in places out of childrenõs reach! Take enough safety precautions prior to operating this model. You are responsible for this modelõs assembly and safe operation! Always keep this instruction manual ready at hand for quick reference, even after completing the assembly. SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE. No KYOSHO

2 REQUIRED FOR OPERATION (Purchase separately!) CAUTION: For details concerning the equipment listed below (size, maker, etc.), check with your hobby shop. 1 A minimum channel radio for airplanes (with 5 servos), and dry batteries. CAUTION: Only use a minimum channel transmitter, configured for aircraft! 5 WARNING: Normal gasoline cannot be used with glow engines. Fuel Bottle A minimum channel transmitter, configured for aircraft AA-size Batteries MODEL ENGINE FUEL AA Extension Lead x (00mm) 1 Y- Harness x 1 AA AA Plug Wrench One-touch Plug Heater Set Ensure you read and understand the instructions included with your radio. Engine and Muffler Model Aircraft Engine.0.5~.53 Stroke.0 Stroke.5 ~.53 Muffler extention adapter ( Stroke) Glow Plug Muffler 6 7 Glue Instant Glue Low Viscosity Type Epoxy Glue Epoxy A Epoxy B Other equipment for enhancing airplane operation & performance Engine Starter Silicon Glue Silicon 1V 1V Battery (for starter) 3 Propeller Purchase a propeller that will match your engine. Others Silicone Tube Vibration Protection Sponge Fuel Filter Spinner Nut TOOLS REQUIRED (Purchase separately!) Sharp Hobby Knife Phillips driver (L, M, S) Awl Needle Nose Pliers Scissors Wire Cutters

3 BEFORE YOU BEGIN 1 Read through the manual before you begin, so you will have an overall idea of what to do. Check all parts. If you find any defective or missing parts, contact your local dealer or our Kyosho Distributor. 3 Symbols used throughout this instruction manual, comprise: Do not overlook this symbol! Apply epoxy glue. mm mm Drill holes with the specified diameter (here: mm). Cut off excess. Apply instant glue (CA glue, super glue). Cut off shaded portion. Ensure smooth non-binding movement while assembling. Assemble left and right sides the same way. Must be purchased separately! Tentatively tighten. The pre-covered film on ARF kits may wrin-kle due to variations of temperature. Smooth out as explained right. with cover (cloth) low setting Use an iron covered with a cloth! Start at low setting. Increase the set-- ting if necessary. If it is too high, you may damage the film. 3

1 Upper Main Wing Cut away only film A = AÕ Note the direction. Top A AÕ Center Sec.

Wipe away excess and let dry. Apply fresh glue to other half of spar and mating surfaces of wing and join. Secure with tape until dry.

Cut away only film If there is a gap, carefully fill with epoxy glue.

3 Lower Main Wing Before cutting away the covering film, lightly heat that area with an iron.

4 1 Upper Main Wing Cut away only film A = AÕ Note the direction. Top A AÕ Center Sec. Apply epoxy glue to wing spar halves and join together. When dry, apply epoxy to one end of wing spar and insert into wing. Wipe away excess and let dry. Apply fresh glue to other half of spar and mating surfaces of wing and join. Secure with tape until dry. Lower Main Wing Note the direction. Top 90mm Dihedral 90mm at wing tip. Cut away only film If there is a gap, carefully fill with epoxy glue. 90mm Join lower wing halves together as for the upper wing(shown above), being careful to check dihedral. 3 Lower Main Wing Before cutting away the covering film, lightly heat that area with an iron. Wing Underside Note the direction Aileron Carefully apply instant glue to both sides of the hinge, ensuring free movement. Align the centre of the main wing with the aileron. Cut off shaded portion. Apply instant glue (CA glue, super glue). Do not disregard this symbol! Apply epoxy glue. Ensure smooth non-binding movement while assembling. Assemble left and right sides the same way.

Lower Main Wing x 8mm TP 8 Aileron Servo Included

1mm Wing Under Side x8mm mm Cut away only film.

6 Lower Main Wing x 0mm x0mm x 0mm Adjustable Rod

5 Lower Main Wing x 8mm TP 8 Aileron Servo Included with the radio set. 1mm Wing Under Side x8mm mm Cut away only film. 5 Lower Main Wing (Upper Side) Cut away only film. 6 Lower Main Wing x 0mm x0mm x 0mm Adjustable Rod (Short) Must be purchased separately! Cut off shaded portion. Assemble left and right sides the same way. Apply epoxy glue. mm mm Drill holes with the specified diameter (here: mm). 5

If the wing separates during flight, you will lose control of your airplane.

6 7 Lower Main Wing Cut away only film. mm Align with the holes in the main wing. 8 Lower Wing To Fuselage Join Temporarily tighten. x 35mm x 1mm Washer x35mm A AÕ A = AÕ 9 Horizontal Tail (Stabiliser) Cut away only film. Securely glue together. If the wing separates during flight, you will lose control of your airplane. Note the direction 3mm Elevator Carefully apply instant glue to both sides of the hinge, ensuring free movement. mm mm Drill holes with the specified diameter (here: mm). Cut off shaded portion. Apply instant glue (CA glue, super glue). Temporarily tighten. Do not disregard this symbol! Apply epoxy glue. Ensure smooth non-binding movement while assembling. Assemble left and right sides the same way. 6

10 Vertical Tail Cut away only film. Securely glue together.

C = CÕ C CÕ A = AÕ B = BÕ B BÕ A AÕ 11 Rudder Slit here for tail gear. Securely glue together.

Rudder mm mm Drill holes with the specified diameter (here: mm). Cut off shaded portion.

7 10 Vertical Tail Cut away only film. Securely glue together. If the wing separates during flight, you will lose control of your airplane. C = CÕ C CÕ A = AÕ B = BÕ B BÕ A AÕ 11 Rudder Slit here for tail gear. Securely glue together. If the wing separates during flight, you will lose control of your airplane. mm Note the direction Carefully apply instant glue to both sides of the hinge, ensuring free movement. Rudder mm mm Drill holes with the specified diameter (here: mm). Cut off shaded portion. Do not overlook this symbol! Apply epoxy glue. Apply instant glue (CA glue, super glue). Ensure smooth non-binding movement while assembling. 7

1 Main Landing Gear Front Lightly heat the film to be

13 Main Landing Gear mm Stoper mm 3x 3mm Set 3x1mm 3 x

main wing to install tank. Fix with silicon glue.

3x35mm 3x35mm After confirming the direc-tion (see front

5mm mm mm Drill holes with the specified diameter (here:

8 1 Main Landing Gear Front Lightly heat the film to be removed with an iron and carefully cut away. 13 Main Landing Gear mm Stoper mm 3x 3mm Set 3x1mm 3 x 1mm TP TP 8 3x 3mm 3x1mm 1 Fuel Tank 3 x 35mm TP Remove main wing to install tank. Fix with silicon glue. 1 Stuff Vibration Protection Sponge. 3x35mm 3x35mm After confirming the direc-tion (see front view of fuel tank), insert and tighten the screw. 5mm mm mm Drill holes with the specified diameter (here: mm). Cut off shaded portion. 8 Assemble left and right sides the same way. Apply instant giue (CA glue, super glue)

15 Engine Mount x 0mm x 10mm Washer 6mm 9mm

1mm 3 Engine shaft line x 0mm x 10mm A A 1 5mm

1mm 3mm Nut Engine Mount 3mm Washer 3mm Spring

9 15 Engine Mount x 0mm x 10mm Washer 6mm 9mm 6mm mm Mount Nut.1mm 3 Engine shaft line x 0mm x 10mm A A 1 5mm A A x 0mm A mm Depends on the position of carburettor. 16 Engine Mount 15mm 3 x 5mm 3mm Spring Washer Use a muffler extension adapter. (purchase separately) 3mm Washer 3.1mm 3mm Nut Engine Mount 3mm Washer 3mm Spring Washer 3x5mm mm mm Drill holes with the specified diameter (here: mm). Cut off shaded portion. Apply epoxy glue. Must be purchased separately 9

17 Cowling x 8mm TP 5 3mm 15mm Relieve the cowl to clear the

x 8mm 1mm 18 Linkage Rod mm Rod mm Adjustable Rod (Long)

Beware of the flame! Be careful not to scorch the heat-shrink tube!

mm mm Drill holes with the specified diameter (here: mm).

10 17 Cowling x 8mm TP 5 3mm 15mm Relieve the cowl to clear the engine head. x 8mm 1mm 18 Linkage Rod mm Rod mm Adjustable Rod (Long) Heat-shrink Tube Beware of the flame! Beware of the flame! Be careful not to scorch the heat-shrink tube! x 19 Horizontal / Vertical Tail x 0mm 5mm mm 10mm x 0mm 10mm x 0mm mm mm Drill holes with the specified diameter (here: mm). Cut off shaded portion. Apply instant glue (CA glue, super glue). Must be purchased separately Apply epoxy glue. x Assemble as many times as specified (here: twice). 10

order to obtain the correct center of gravity(cg), position the servo mount accordingly and

11 0 Linkage Elevator Rod Rudder Rod 1 Linkage 3 x 3mm Set 1 Throttle Servo Linkage Stopper 1 Elevator Rod Plastic Parts 1 Elevator Servo 3x3mm Throttle Rod Rudder Rod Plastic Parts 9 In order to obtain the correct center of gravity(cg), position the servo mount accordingly and fix mount securely with epoxy glue Rudder Servo Must be purchased separately! Apply epoxy glue. 11

12 Fuselage x 8mm TP TP 8 x 8mm Paint the canopy frame to mach the fuselage 1mm 3 Main Wing Stay Joint 1 3 x 1mm TP TP 1 Upper Main Wing (Under side) 3x1mm Lower Main Wing (Upper side) 3x1mm mm mm Assemble left and right sides the same way. Cut off shaded portion. mm mm Drill holes with the specified diameter (here: mm). 1

Front Long 3 x 16mm 3 mm 3 mm 3 x 16mm 3 x 16mm 3 x 18mm Assemble left and

13 Lower Main Wing x 35mm x 1mm Washer A AÕ x35mm A = AÕ 5 Wing Joining 3 x 18mm TP TP Front 3 x 16mm 1 3mm Nut 1 Front Front 3mm Washer 1 mm Short Front Front Long 3 x 16mm 3 mm 3 mm 3 x 16mm 3 x 16mm 3 x 18mm Assemble left and right sides the same way. mm mm Drill holes with the specified diameter (here: mm). 13

6 Receiver / Battery Carefully install the receiver and battery pack to ensure that they will not

(After checking CG in step ) 9 Secure foam padding with rubber bands or tape as required.

Swedish Crown markings For the correct placement of decals, please refer to the box top and

each control surface to the values in the diagrams. These values fit general flight capabilities.

14 6 Receiver / Battery Carefully install the receiver and battery pack to ensure that they will not shift during flight. (After checking CG in step ) 9 Secure foam padding with rubber bands or tape as required. Receiver Receiver Power Supply Foam Protection 7 Decals Kit includes decals for Royal Air Force and Swedish Crown markings For the correct placement of decals, please refer to the box top and illustrations below (Some markings are not included) 8 Control Surface Movement Adjust the travel of each control surface to the values in the diagrams. These values fit general flight capabilities. Readjust according to your needs and flight level. RUDDER ELEVATOR AILERON 30mm 30mm 15mm 15mm Position for left diagram. 10mm 10mm Position for left diagram. Must be purchased separately! Do not disregard this symbol! 1

15 9 Centre of Gravity (C of G) 5-55mm Ensure all screws are securely tightened before flight. Check C of G position before flying. If necessary, re-position receiver and battery to get correct C of G. CG 5-55mm Do not disregard this symbol! 50 This aircraft has been designed for intermediate to experienced level flyers. First time pilots should seek the advice of more experienced flyers during construction and for initial flights. Initially, less experienced pilots should only fly with an experienced pilot, until they become more proficient. This aircraft is designed to be powered by either a stroke.0 class size engine or a stroke 50class size engine. Installation of engines other than those specified could to lead to a serious accident and/or damage to property. SPARE PARTS No. Part Names Cowling Canopy Main Gear Wing Stay Set x1 x Quantity x1 x x FOR JAPANESE MARKET ONLY. No. Part Names Quantity N x Stay Joint x Decals x Repair Films (Satin Yellow)

16 Direct-Mail-Parts-Order-System" is available only for Japanese market "Kyosho (1) (3) () 1, ,680 () (1) ()

17 11837 TIGER MOTH 0

18 FLIGHT MANUAL Always do observe the following in order to prevent accidents! Before Flying Flying After Flying Cautions for Safety Before flying your airplane, ensure the airfield is spacious enough. Always fly it outdoors in safe areas with no debris or obstacles! Do not fly your airplane when there is a strong wind or a lateral wind. Always land your airplane into the wind. WIND Adjust the engine always from behind, but never from infront or the sides as a rotating propeller may badly injure you! For handling the radio properly, refer to its instruction manual. Ensure the spinner and propeller are securely attached. If your airplane begins to operate by itself, there is another transmitter on your frequency. Immediately stop your airplane; otherwise you may lose control of it which will result in accidents. OFF ON Fully extend the transmitter antenna. Switch on the transmitter. ON Switch on the receiver. ON Fill the fuel tank. By moving the control sticks, ensure all control surfaces moves as per your adjustments. By moving the throttle control stick, ensure the carburetor opens and closes without effort. For starting the engine, apply low throttle and hold the engine starter against the spinner. Adjust the needle. Bring your airplane to a halt by lowering the throttle trim. After each flight, the engine is very hot. Beware of getting burned! Switch off the receiver. OFF Switch off the transmitter. OFF ON OFF Draw out the remaining fuel from the fuel tank and fill it back into the can. Wipe away any fuel deposits or dirt. Do not allow watching people to get too close to a rotating propeller. Immediately disuse defective propellers as well as deformed spinners. If the dry batteries in the radio are flat, replace them with fresh ones. Do not fly your airplane above people standing around. Ensure the wings are securely attached. Hand-launch your airplane into the wind to make it take off. WIND Only use KYOSHO genuine parts! Never throw burning, gleaming or smouldering things into fuel cans, even if these happen to be empty. This will result in serious injury! THE FINEST RADIO CONTROL MODELS PRINTED IN CHINA R

p01.pdf

p01.pdf Before commencing assembly, please read these instructions thoroughly! WINGSPAN: 156mm R THE FINEST RADIO CONTROL MODELS For Intermediate & Advanced Flyers. INSTRUCTION MANUAL RADIO CONTROLLED ENGINE POWERED