p01.pdf

Size: px

Start display at page:

Download "p01.pdf"

きみのしんらぶり
4 years ago
Views:

1 Before commencing assembly, please read these instructions thoroughly. THE FINEST RADIO CONTROL MODELS R WINGSPAN: 575mm (6") For Advanced Flyers INSTRUCTION MANUAL RADIO CONTROLLED ENGINE POWERED SPORTS AIRCRAFT INDEX REQUIRED FOR OPERATION BEFORE YOU BEGIN ASSEMBLY OPTIONAL PARTS OPERATING YOUR MODEL SAFELY 3 3~0 ~ SAFETY PRECAUTIONS This radio control model is not a toy! First-time builders should seek the advice of experienced modellers before commencing assembly and if they do not fully understand any part of the construction. Assemble this kit only in places out of children s reach! Take enough safety precautions prior to operating this model. You are responsible for this model s assembly and safe operation! Always keep this instruction manual ready at hand for quick reference, even after completing the assembly. SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE. 00 KYOSHO No.8

2 REQUIRED FOR OPERATION (Not included in kit!) CAUTION: For details concerning the equipment listed below (size, maker, etc.), check with your hobby shop. 5x 5 A minimum channel radio for airplanes (with 5 standard servos), and nicad or alkaline batteries are required. CAUTION: Only use a minimum channel radio for aircraft! (No other radio may be used!) 5 Required for engine starting: Glow engine fuel only. MODEL ENGINE FUEL Fuel Primer WARNING: Normal gasoline cannot be used with glow engines. One-touch Plug Heater Set A minimum channel transmitter for aircraft with 5 servos. Plug Wrench aileron extension cords. For handling the radio properly, refer to its instruction manual. 6 Glue Instant Glue 30 Epoxy Glue (30 minutes type) Epoxy A Engine and Muffler Model Airplane Engine 90 / -stroke.90 (OS MAX-9FX / 90 / -stroke.90 (OS FS-9S/ ENYA 90-CTN / SAITO FA-9S) *Do not use more powerful engine above. Glow Plug Muffler 7 Silicon Glue SILICON Epoxy B Other equipment for enhancing airplane operation & performance Engine Starter V V Battery (for starter) 3 Propeller and Spinner Purchase a propeller that will match your engine. Propeller Fuel Filter Polyurethane paint (Clear) Sponge Sheet Fuel line PP Pipe Spinner(6mm A B TOOLS REQUIRED (Purchase separately!) Sharp Hobby Knife Needle Nose Pliers Scissors Wire Cutters Awl Phillips Screwdriver (L, M, S) Drill, Handgrinder

Apply instant glue (CA glue, super glue). Assemble left and right sides the same way. mm mm Drill holes with the specified diameter (here: mm). Cut off shaded portion. Must be purchased separately!

3 BEFORE YOU BEGIN 3 Read through the manual before you begin, so you will have an overall idea of what to do. Check all parts. If you find any defective or missing parts, contact your local dealer or our Kyosho Distributor. Symbols used throughout this instruction manual, comprise: Apply epoxy glue. Apply instant glue (CA glue, super glue). Assemble left and right sides the same way. mm mm Drill holes with the specified diameter (here: mm). Cut off shaded portion. Must be purchased separately! Cut off excess. Ensure smooth non-binding movement while assembling. Pay close attention here! Do not overlook this symbol! The pre-covered film on ARF kits may wrin-kle due to variations of temperature. Smooth out as explained here. with cover (cloth) low setting Use an iron covered with a cloth! Start at low setting. Increase the set-- ting if necessary. If it is too high, you may damage the film. You can keep the covering film from wrinkling or peeling by spraying the plane with clear polyurethane. Main Wing Install the hinges completely before applying instant glue. Align the center line of main wing with aileron. Securely glue together. If it comes off during flights, you may lose control of your airplane, resulting in an accident! Top view. Main Wing Note the direction. Securely glue together. If it comes off during flights, you may lose control of your airplane, resulting in an accident! Top Front Fill the gap with epoxy. Dihedral. Only cut the film. Do not cut into the wood. 50 mm 3

3 Main Wing (Bottom view) x 6mm x 6mm Screw mm mm 7 Adjust the

Do not cut into the wood. Securely glue together.

x 0mm Cap Screw mm Washer Bottom view Only cut the film.

.mm Bottom view x 0mm A A mm A = A Apply epoxy glue.

4 3 Main Wing (Bottom view) x 6mm x 6mm Screw mm mm 7 Adjust the travel of each control surface. Please refer 7. Only cut the film. Do not cut into the wood. Securely glue together. If it comes off during flights, you may lose control of your airplane, resulting in an accident! Main Wing Top view Only cut the film. Do not cut into the wood. x 0mm Cap Screw mm Washer Bottom view Only cut the film. Do not cut into the wood..mm Bottom view x 0mm A A mm A = A Apply epoxy glue. Must be purchased separately! Cut off shaded portion. Do not disregard this symbol! Assemble left and right sides the same way. mm mm Drill holes with the specified diameter (here: mm). Pay close attention here!

5 Engine Mount x 0mm Cap Screw mm Mount Nut 5mm Engine shaft line A A Side View 36mm 3.5mm Depends on the position of carburettor. Align the mark on both mounts with the center mark on the balk head.

5 5 Engine Mount x 0mm Cap Screw mm Mount Nut 5mm Engine shaft line A A Side View 36mm 3.5mm Depends on the position of carburettor. Align the mark on both mounts with the center mark on the balk head. A mm 5.5mm mm x 0mm mm 6 Fuel Tank 3 x 35mm TP TP Screw After confirming the posi-tion of the fuel tank's internal parts(see front view), insert and tighten the screw. Fix tank with silicon glue. 3 x 35mm 5mm Silicon Tube 7 Engine Mount x 5mm Cap Screw mm mm Engine Mount mm Washer mm x 5mm mm Nut mm Spring Washer Throttle Rod PP Pipe Apply epoxy glue. mm mm Drill holes with the specified diameter (here: mm). Must be purchased separately! Cut off shaded portion. 5

8 Main Landing Gear mm mm x 0mm Screw mm mm mm Washer 3 x mm mm mm mm Spring

3mm 9 Vertical/Horizontal Tail Only cut the film. Do not cut into the wood.

Install the hinges completely before applying instant glue.

If it comes off during flights, you may lose control of your airplane,

A = A B = B C = C D = D B B C C A A D D Apply epoxy glue.

6 8 Main Landing Gear mm mm x 0mm Screw mm mm mm Washer 3 x mm mm mm mm Spring Washer Secure Wheel Pants with Silicon Glue. mm Nut 6 3 x mm 3 x mm TP TP Screw.3mm 9 Vertical/Horizontal Tail Only cut the film. Do not cut into the wood. Only cut the film. Do not cut into the wood. Install the hinges completely before applying instant glue. Only cut the film. Do not cut into the wood. Securely glue together. If it comes off during flights, you may lose control of your airplane, resulting in an accident! A = A B = B C = C D = D B B C C A A D D Apply epoxy glue. Pay close attention here! Ensure smooth non-binding movement while assembling. Do not disregard this symbol! Cut off shaded portion. mm mm Drill holes with the specified diameter (here: mm). Apply instant glue (CA glue, super glue). 6

0 Horizontal / Vertical Tail.6 x 8mm TP TP Screw mm.6 x 8mm Bend as shown. mm Install the hinges completely before applying instant glue. Securely glue together.

If it comes off during flights, you may lose control of your airplane, resulting in an accident! mm Elevator Cut extra portion. Rudder mm Beware of the flame!

7 0 Horizontal / Vertical Tail.6 x 8mm TP TP Screw mm.6 x 8mm Bend as shown. mm Install the hinges completely before applying instant glue. Securely glue together. If it comes off during flights, you may lose control of your airplane, resulting in an accident! Rod mm Securely glue together. If it comes off during flights, you may lose control of your airplane, resulting in an accident! mm Elevator Cut extra portion. Rudder mm Beware of the flame! mm Be careful not to scorch the heat-shrink tube! Rudder Elevator Apply epoxy glue. Ensure smooth non-binding movement while assembling. Apply instant glue (CA glue, super glue). Do not disregard this symbol! mm mm Drill holes with the specified diameter (here: mm). Pay close attention here! 7

Linkage Elevator Elevator Rudder Elevator Rudder / Elevator Cut it in accordance with the contour of PP pipe.

3 Linkage x 6mm Screw 6 PP pipe 7 Adjust the travel of each control surface. Please refer 7.

If it comes off during flights, you may lose control of your airplane, resulting in an accident!

8 Linkage Elevator Elevator Rudder Elevator Rudder / Elevator Cut it in accordance with the contour of PP pipe. Cut off the PP pipe. Cut it in accordance with the contour of PP pipe. 3 Linkage x 6mm Screw 6 PP pipe 7 Adjust the travel of each control surface. Please refer 7. mm x mm PP PP pipe PP PP pipe mm Securely glue together. If it comes off during flights, you may lose control of your airplane, resulting in an accident! Cut off shaded portion. mm mm Drill holes with the specified diameter (here: mm). Apply epoxy glue. Pay close attention here! Do not disregard this symbol! Ensure smooth non-binding movement while assembling. Must be purchased separately! Assemble left and right sides the same way. 8

9 Linkage 3mm Set Screw Linkage Stopper 3mm Linkage Stopper Throttle Rod mm Nut mm mm Included with the radio set. mm mm Washer Receiver Throttle Servo Elevator Servo Rudder Servo Battery Secure foam padding with rubber bands or tape as required. Install carefully the receiver and battery pack to ensure that they will not move during flights. 7 If necessary, re-position receiver and battery to get correct C of G. Making sure the line of edge, apply epoxy glue. Front 7 Adjust the travel of each control surface. Please refer 7. Securely glue together. If it comes off during flights, you may lose control of your airplane, resulting in an accident! mm mm Drill holes with the specified diameter (here: mm). Apply epoxy glue. Must be purchased separately! Do not disregard this symbol! Cut off shaded portion. Ensure smooth non-binding movement while assembling. Pay close attention here! 9

0 NARUKE SP600 5 Canopy.6 x 8mm TP TP Screw mm Silver Decal 8mm Cut off.

6 x 8mm Trim the cowling so it will match your engine.

SP600 Position for diagram RUDDER 50mm 50mm CG 5mm AILERON Position for diagram 0mm

For the correct placement of decals, please refer to box top.

10 0 NARUKE SP600 5 Canopy.6 x 8mm TP TP Screw mm Silver Decal 8mm Cut off..6 x 8mm 6 Cowling mm.6 x 8mm TP TP Screw mm.6 x 8mm Trim the cowling so it will match your engine. 8mm 7 Adjust the travel of each control surface to the values in the diagrams. SP600 Position for diagram RUDDER 50mm 50mm CG 5mm AILERON Position for diagram 0mm 0mm ELEVATOR Position for diagram 6mm 6mm 8 Decal Apply included decals. For the correct placement of decals, please refer to box top. Cut off shaded portion. mm mm pecified diameter (here: mm). Apply instant glue (CA glue, super glue). Pay close attention here! Must be purchased separately! Assemble left and right sides the same way.

11 *This aircraft is for intermediate to advanced builders and flyers only. Biginners connot fly and building this aircraft. *This aircraft has been flight tested with snap-rolls and other aerobatic maneuvers. However, repeated violent maneuvers may overstress the airframe. Please fly in a way that will not otherstress the airframe. *Repeated flyng can cause stress cracks to appear in the wood and joints, please inspect after each flight. If any abnormalities are noted, repair immediately befor the next flight to avoid accsidents. *Glue joints can loosen even thoogh they appear to be tight. If you notice irregular flight, investigate the cause and repair it befor the next flight. *Even though the kit's supplied with fitted linkages, inprpely assembling then can result in binding or loose control surfaces. This can cause flutter and aircraft control problems. Make suer all linkages are tight and control surfases move properly before flying. *This aircraft is designed for -stroke.90 or -stroke.90 sized engines only. Using larger, more powerful engens is not safe and may result in airframe failure.do not exceed the recommended engine size or engage in extreme aerobatic maneuvers. Do not overlook this symbol! PARTS :FOR JAPANESE MARKET ONLY. No. Part Names 8-0 Cowling 8-0 Wheel pants 8-03 Main gear Quantity (R), (L) No. Part Names Quantity Decale Canopy OPTIONAL PARTS :FOR JAPANESE MARKET ONLY. No. Part Names Nylon Spinner (White) 90-6 Nylon Spinner (Red) 90-6 Nylon Spinner (Yellow) No Part Names PP P.P. Pipe OS70~OS0(UNF 5/6-7) OS.70~OS.0(UNF 5/6-7) Fuel Tube Stopper

12 FLIGHT MANUAL Always do observe the following in order to prevent accidents! Before Flying Flying After Flying Cautions for Safety Before enjoying flying your airplane, sufficiently make sure the airfield is spacious. Always fly it outside rooms in safe areas with no debris or obstacles! Do not fly your airplane when there is a strong wind or side wind. Always land your airplane into the wind. WIND Always regulate the engine from behind, but never from infront or from the sides, because a rotating propeller might badly injure you. For radio equipment, refer to the manual included with the radio. Check that the spinner and the propeller are securely fastened. If the model begins to operate by itself, there is another transmitter on your frequency. Do not try to operate your model under such condition for it may go out of control. OFF ON Fully extend transmitter antenna. Switch on the transmitter. ON Switch on the receiver. ON Fill in the fuel. By moving the controls (transmitter), check that all rudders move the way you adjusted them. By moving the throttle control, check that the engine carburetor easily opens and closes. For starting the engine, apply low throttle and hold the engine starter against the spinner. Adjust the needle. Bring your airplane to a halt by lowering the engine control trim. After each flight, the engine is hot. Beware of getting burned. Switch off the receiver. OFF ON OFF Switch off the transmitter. OFF Draw the remaining fuel out of the tank and fill it back into the can. Wipe up any fuel deposits or dirt. Do not allow watching people to get too close to a rotating propeller. Immediately disuse defective propellers as well as deformed spinners. If the batteries of the radio system are flat, replace them with new ones. Do not fly your airplane above people standing around. Check that the wings are properly and firmly affixed. Hand-launch your airplane into the wind and make it take off. WIND Only use KYOSHO genuine parts. Never throw burning, gleaming or smouldering things into fuel cans, even if these happen to be empty. This could result in serious injury () 0:00~8: THE FINEST RADIO CONTROL MODELS PRINTED IN CHINA R

13 () (3) (), ,680 () () ()

14 8

p01.pdf

p01.pdf Before commencing assembly, please read these instructions thoroughly. R WINGSPAN: 30mm THE FINEST RADIO CONTROL MODELS For Intermediate & Advanced flyers. INSTRUCTION MANUAL RADIO CONTROLLED ENGINE POWERED