Kyosho Fantom Sports Manual

Transcription

1 Before commencing assembly, please read these instructions thoroughly! R THE FINEST RADIO CONTROL MODELS FANTOM SPORTS INSTRUCTION MANUAL :8 Scale Radio Controlled. Engine Powered WD Racing Car Series Castrol TOM'S SUPRA INDEX REQUIRED FOR OPERATION RADIO PREPARATION BEFORE YOU BEGIN ARRANGEMENT OF PLASTIC PARTS ON RUNNERS 6 ASSEMBLY OPERATING YOUR MODEL SAFELY EXPLODED VIEW 3 33 SPARE PARTS & OPTIONAL 3 37 PARTS SAFETY PRECAUTIONS This radio control model is not a toy. 000 KYOSHO First-time builders should seek the advice of experienced modellers before commencing assembly and if they do not fully understand any part of the construction. Assemble this kit only in places out of children's reach! Take care before operating this model. You are responsible for this model's assembly and safe operation! Always keep this instruction manual ready at hand for quick reference, even after completing the assembly. SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE. No. 30

2 R R REQUIRED FOR OPERATION () ch radio control set with servos. Stick-type ch radio set. Wheel-type This kit requires a channel radio control set with servos. ch radio set. Because there are stick-type and wheeltype transmitters, use which ever fits your convenience best. Switch the reverse (transmitter) for the throttle control. For more information on the radio con-trol set, refer to its instruction manual. AA-size Batteries (For Transmitter) Ni-Cd Battery No.73 Suitable servos & receiver Servo 38mm Receiver 90mm 57mm AA AA 59mm 36.5mm Required for engine starting: Glow Fuel Fuel Pump Plug Heater Glow Engine Fuel No RC No.96 No.96 Quick Fill Fuel Bottle One-touch Plug Heater Set Plug Wrench Starter Battery No.803 Locking Jig & Wrench 3 Paint For painting the body, use Kyosho paints for models! No.30 POLYCA COLOR No KYOSHO SPRAY COLOR KY OSH O S PR AY CO LO R KY OSH O S PR AY CO LO R Other equipment required. Tape

3 5 Tools required REQUIRED FOR OPERATION () Phillips Screwdriver ( L. M. S ) Needle Nose Pliers Instant Glue Sharp Hobby Knife Wire Cutters Screw Cement Box Wrench Awl Pliers Rubber Cement TOOLS INCLUDED Hex Wrench Grease Grease Cross Wrench (S) No.803 No.89 SPECIAL TAPER REAMER ROUND CUTTER & SANDER No need to pre-drill! Drills neat mm to 5mm holes directly! For trimming bodies! Cutting along curved lines never was so easy! RADIO PREPARATION Set up the radio control system as indicated below START FINISH 8 Install batteries. (Transmitter) Extend the antenna. (Transmitter) 3 Connect the charged Ni-Cd battery to the receiver. Extend the antenna. (Receiver) 5 Center the trims. 6 Switch on. (Transmitter) 7 Switch on. (Receiver) 8 Make sure the servos are in command. 9 Switch off. (Receiver) 0 Switch off. (Transmitter) Retract the antenna. (Transmitter)

4 BEFORE YOU BEGIN () Read through the manual before you begin, so you will have an overall idea of what to do. 3 Check all parts. If you find any defective or missing parts, contact your local dealer or our Kyosho Distributor. How to read the instruction manual: No., No.5, No.6 Front Suspension 5 x 0mm Metal Bushing Example This instruction manual uses several symbols. Please note them during the entire assembly. 5 King Pin mm Pillow Ball (Black) 6 R 7 L 5 8 Key Number, Part Name, True-to-scale Diagram, Quantity Used All parts except screws are identified by key numbers. For purchasing spare parts, find the key no. of the part needed in the spare part list and refer to the left column to look up the corresponding order no. Symbols used throughout the instruction manual, comprise: Part bags used. Apply instant glue (CA glue, super glue). mm Assemble left and right sides True-to-scale diagram. the same way. Drill holes with the specified Must be purchased separately! diameter (here: mm). Apply rubber cement. Cut off shaded portion. Pay close attention here! Apply threadlocker (screw cement). Ensure smooth non-binding movement while assembling. x Apply grease. Tentatively tighten. Assemble as many times as Assemble in the specified specified (here: twice). order.

5 BEFORE YOU BEGIN () 5 This kit contains screws and hardware in different metric sizes and shapes. Before using them, check the screws on the true-to-scale diagrams on the left side in each assembly step. Some screws are extras. SCREWS OTHER HARDWARE Screw Self-tapping (TP) Screw Screw WasherNut E-ring Cap Screw TP F/H Screw mm 3mm 3mm mm Flat Head (F/H) Screw F/H Screw Metal BushingBearing 5mm Pillow Ball 3mm mm 0mm 5.8mm 6 Correct Self-tapping (TP) screws cut threads into the parts when being tightened. Excessive force may Wrong permanently damage parts when tightening TP screws. It is recommended to stop tightening when the part is attached or when some resistance is felt after the threaded portion enters the plastic. Overtightened. The threads are stripped. 5

6 ARRANGEMENT OF PLASTIC PARTS ON RUNNERS Shaded Parts are not used R L E D D E A F C C K H 0 69 B A 6B 6C

7 No., No.3 Front Suspension < Right > 3 x 5mm Screw mm Ball Stud 3 x 3mm x 8mm < Left > x8mm 0 3 x8mm 3x3mm Firmly tighten the 3x3mm set screws onto the flat spots. 3x3mm x5mm 9 No., No.3 Front Suspension 3 x 3mm E3 E E-ring < Right > 6 < Left > E3 E3 Put into this space. 3 3x3mm 5 Part bags used. Assemble left and right sides the same way. Tentatively tighten. 7

8 No., No., No.3 3 Front Shaft C C-ring C C-ring 68 xx5mm Ball Bearing x x mm Collar Front Suspension No., No.3 87 < Left > < Right > 7 xmm x mm TP TP F/H Screw 6 xmm No., No.3, 5 Front Suspension No.3 86 x 8 x 0.5mm 86 Washer < Left > L "L" marked. < Right > R "R" marked. 6 xx5mm Metal Bushing 8 3 x 3mm 85 3 x 0mm Pin Firmly tighten the set screws onto the flat spots. Part bags used. Assemble left and right sides the same way. 8

9 No., No.3, No.3 6 Front Suspension < Right > < Left > mm Hex Wrench (5mm) mm Ball Stud mm Ball Screw 0 0mm Screw Cap 7 Front Suspension No.3, No.3 < Right > 83 Please refer to the Setting Data Sheet about the setting for screws. Tighten screws one after the other. 83 Front Swing Shaft.5mm Hex Wrench (.5mm) < Left > 8 Bumper No., No.3 mm mm x 5mm F/H Screw 3 mm Nylon Nut 3 50 x5mm x5mm Part bags used. Assemble left and right sides the same way. Ensure smooth non-binding Apply grease. movement while assembling. 9

10 9 Body Mounts 06 No., No.3 3x0mm 08 xmm 3 x 0mm TP TP F/H Screw x mm TP Screw No., No.3 0 Rear Suspension < Right > < Left > x8mm 5 Note the direction. 8 9 Long Short 3x3mm 99 x 8mm 3 x 3mm 7 Firmly tighten the set screws mm onto the flat spots. Rear Lower Suspension Shaft Ball Stud No., No.3 Rigid Axle C C-ring 66 C C-ring Tighten C-Ring with wrench if it is loose. 68 x x 5mm Ball Bearing x 5mm Pin 90 Part bags used. Assemble left and right sides the same way. Tentatively tighten. 0

11 No.5, No.3 Speed Changer x mm.6 x mm Cap Screw 35.6 x 3 x 5.5mm Collar 0 5mm Roller 39 Speed Spring.6xmm mm 35.6xmm Tighten.6mm Cap Screw to 35 Collar till the screw stops, and unscrew rounds, then please set up according to the track condition xmm xmm 89 Firmly tighten the set screws onto the flat spots. No.5, No.3 3 Speed Changer 3 x 6mm F/H Screw x x mm Metal Bushing 3 x 0mm Cap Screw 0 3 x mm 96 3 x 8 x mm Collar Washer x6mm x6mm Note the direction. 3x0mm Part bags used. Apply threadlocker (screw cement). Apply grease.

12 ASSY Rear Assembly No., No.6, No.3 97 x8mm 5 mm xmm xmm xmm Firmly tighten the xmm set screws onto the flat spots Push to the end x 0mm Pin x mm TP TP F/H Screw Cut off excess inside of the holes x8mm Cut off excess inside of the holes. x mm 9 9 x 8mm 67 6 x 3 x 5mm Ball Bearing 93 xmm 67 ASSY 5 Rear Assembly No.6, No.3 7 xmm x 8mm F/H Screw x8mm x8mm x mm TP TP F/H Screw 8 xmm xmm xmm Part bags used. Apply rubber type glue. Tentatively tighten. Apply threadlocker True-to-scale diagram. (screw cement).

13 No., No.7, 6 Rear Suspension No.3 < Left > 3 x 3mm 86 L 85 3 x 0mm For Left ("L" marked) Pin 8 xx5mm Metal Bushing x 8 x 0.5mm Washer < Right > Firmly tighten the set screws onto the flat spots. No., No.7, No.3 7 Rear Suspension < Right > < Right > 6 < Left > "L marked". "R marked". < Left > mm 9 Hex Wrench (5mm) mm Hex Wrench (.5mm) Be careful not to screw bent. Please refer to the Setting Data Sheet about the setting mm 03 9mm Screw Cap Ball Screw 6 6 No.7, No.3 8 Rear Suspension 3x3mm Tighten screws one after the other. 3 x 3mm 8 Rear Swing Shaft 8 < Left > Please refer to the Setting Data Sheet about the setting..5mm Hex Wrench (.5mm) Part bags used. Assemble left and right sides the same way. Ensure smooth non-binding movement while assembling. Apply grease. 3

14 9 Body Mounts No., No.3 3x0mm 3 x 5mm TP TP Screw x 0mm TP TP F/H Screw 3x5mm 0 Body Mounts No., No.8, No To the inner hole. 3x8mm 3x8mm E.5 E E-ring 3 x 8mm F/H Screw 35 Note the direction. E For Left For Right 36 3 E.5 If you use the outer holes for rear body mount, Please shave the shaded portion off. Body Mounts x 6mm TP TP Screw 3 x 0mm Screw No., No.3 x6mm 3x5mm 05 3x0mm 05 x6mm 3x0mm 3 x 5mm Screw 38 3x5mm 38 Part bags used. Ensure smooth non-binding movement while assembling. Assemble left and right sides the same way.

15 Pulley < > 7T < Pulley 7T > < > 6T No.8, No.3 < Pulley 6T > Small holes should be on Small holes should be on E7 same side. same side Use in E7 E7 E E-ring 3 58 x 6 3 Middle Block No., No.8, No.3 xmm xmm x mm 7T Pulley 7T 67 6 x 3 x 5mm Ball Bearing 6 x 9 x 3.5mm Collar xmm Firmly tighten the xmm set screws onto the flat spots. 88 6T Pulley 6T Middle Block No.3 Middle Block x mm TP TP F/H Screw xmm xmm x Part bags used. Assemble as many times as specified. Apply threadlocker (screw cement). 5

16 5 Center Bulk No., No.9, No.3 6 x mm TP F/H Screw x mm xmm 37 6 Note the direction. xmm xmm xmm 6 Steering 73 No., No.9, No.3 5.5mm approx. 5.5mm 56 FUTABA 69 F Serrated Cap (F) KO 70 KJS JR SANWA Serrated Cap (KJS) HITEC 0 H Serrated Cap (H) 3mm x Steering Rod 99.8mm 3mm Ball Stud Nylon Nut 73.8mm Ball End (Medium) Part bags used. True-to-scale diagram. x Assemble as many times as specified. 6

17 7 Belt x mm No.9, No.3 xmm Firmly tighten the xmm set screws onto the flat spots. 7T Pulley 7T 88 xmm mm Hex Wrench (mm) 8 Fuel Tank 3 x 8mm F/H Screw 3mm Nylon Nut 3 x 8 x 0.5mm Washer 8 O P O-ring P No., No.9, No mm 3mm x8mm 9 Battery No. 8.5mm Battery of over 8.5mm width cannot be used. KYOSHO 73 6V-mAh Suitable Battery KYOSHO 73 6V-mAh Ni-Cd Battery Press this part slightly if it is needed. Fix with Glass Tape, etc. Battery 3 Part bags used. Must be purchased separately! Apply threadlocker (screw cement). 7

18 No., No.9, No.3 30 Steering Servo x8mm.6x8mm 3 Cut the ends off. Steering Servo x8mm 8 x8mm x8mm Do not tighten x8mm too much. JR 3 In the case of JR's servo, Please attach and 3 on contrary sides. x8mm x 8mm 8 O P3.6 x 8mm O-ring P3 Cap Screw 8.6x8mm O ÒOÓ marked Please refer to the Setting Data Sheet about this setting. No., No.9, No.3 3 Belt Tensioner 3 x 5mm Screw 3mm () 3 3 x 6 x 5mm (Nylon Nut) Metal Bushing 3 3mm 3mm Nylon Nut 3 x 8 x 0.5mm 3mm Washer Nut 8 Adjust Nylon nut to rotate part 3 smoothly. 3mm 3x5mm 3mm 3 Radio Plate No.3 3x0mm Belt Tensionner Holes used. Front Steering Servo 3 x 0mm TP TP Screw 3x0mm(F/H) 3x0mm(F/H) 3 x 0mm TP TP F/H Screw 6 3x0mm (F/H) Battery Part bags used. Cut off shaded portion. Must be purchased separately! 8

19 33 Receiver 73 Antenna Pipe Come with radio. 0 No., No.9 0 Nylon Strap (Middle) Receiver Switch Attach on the corner. Receiver / No.9, No.3 3 Throttle Servo / Radio 3x5mm 3 x 5mm TP TP Screw 6 3x5mm 8 O P3 O-ring P3 8 3x5mm A 35 Radio Plate No.3 3x0mm xmm 3 x 0mm TP TP F/H Screw 3x0mm x mm TP TP Screw Set up according the servo you use..6 x 0mm Cap Screw 3 x 0mm Cap Screw.6x0mm 3x0mm Set up according the servo you use. Part bags used. Must be purchased separately! 9

20 36 Engine No.0, No.3 E-9 E E-ring 5 Note the direction. 37 Engine No.0, No.3 3 x 8mm Screw 5 x 0 x 0.5mm Washer 33 5 x 0 x mm Ball Bearing x 7 x 0.mm Shim 3 5x0x0.5mm x8mm Engine No.3 3 x 8mm Screw 3x8mm Tighten the screws with one sheet of paper inserted between both gears. 3x8mm Part bags used. Apply threadlocker (screw cement). 0

21 39 Muffler No., No., No.3 3 x 0mm Cap Screw x mm TP TP F/H Screw x mm 7 Muffler Holder 3 3mm 3mm Spring Washer xmm 7 3x0mm xmm 33 3 xmm 30 7 Bend and adjust to the muffler. 3 Tighten the parts with Nylon Straps (Mid size). 0 Linkage No.9, No.0, No.3.6mm(Nylon) 3x3mm C Cut off the fuel tube. 6B 57.6x5mm 3x3mm.6mm.6mm Servo Horn Come with radio. 3x3mm 63.6x5mm mm(Nylon) x3mm.6 x 5mm 6 mm Screw Stopper 3 3 x 3mm.6mm Nylon Nut 63.6mm Throttle Brake Spring Nut 58 Part bags used. Must be purchased separately! Ensure smooth non-binding movement while assembling.

22 No.0 Air Cleaner Tighten the parts with Nylon Straps (Mid size) Fuel Tube No.0 77 Fuel Tube No., No. 3 Front Shock 55 E.5 E E-ring 73.8mm Ball End (Medium) E.5 A 8 B A Piston E Oil x x Part bags used. Assemble as many times as specified. Apply rubber type glue.

23 Front Shock No. E 5 C mm x mm x pcs. D C.5mm x.5mm x pcs. C mm x mm x pcs. For Front (Short) x 5 Rear Shock E.5 E E-ring 7.8mm Ball End (Short) E.5 A Piston No., No., A 8 B 55 E Oil x 6 RearShock No., No. For Rear (Blue) 53 D C.5mm x.5mm x pcs. For Rear (Long) x x Part bags used. Assemble as many times as specified. 3

24 No., 7 Front Shock No mm Ball Nut 3 x 8mm F/H Screw 0 3x8mm Front Shock 8 Rear Shock No., No mm Ball Nut 3 x 8mm F/H Screw 0 3x8mm Rear Shock 9 Wheels < > < Front > Form the tires with Tire Setter (Purchase separatly.) as illustration shown. 35 < > 36 < Rear > Make the edge round. Make the edge round. 68mm 76mm 0.5 degree. degree. Part bags used. Assemble left and right sides the same way.

25 50 Wheels < > < Rear > < > < Front > Front Wheel Rear Wheel 5 Body Shell Drill holes for fuel supply. 9 5mm Drill holes for Plug Heater. Drill holes for Antenna. 5mm 5mm mm 6mm 3mm 3mm mm Drill holes for cooling down. 6mm 5mm mm Drill holes for muffler tail pipe. 3mm 0 3mm mm Drill holes for needle valve adjustment. Part can be cut off. mm 3mm Assemble left and right sides the same way. Cut off shaded portion. 3mm Drill holes with the specified diameter. 5

26 5 Painting Before painting, use a neutral detergent to remove any oil residues and dirt. Mask the windows from the inside. 3 Paint the body shell from the inside using KyoshoÕs spray colors. After painting, remove the protective film from the body shell. No.7630 White Mask White White White Mask 53 Plastic Parts x 8mm Screw No. x8mm 3x0mm(F/H) mm 3x0mm(F/H) mm mm 3 x 0mm TP TP Screw 8 mm mm mm x8mm 3 x 0mm TP TP F/H Screw mm mm Nut Washer 8 3x0mm x0mm 3x0mm 3x0mm 6 Part bags used. Apply threadlocker (screw cement).

27 5 Decals Apply the decals to the positions indicated in numerical order. The decal numbers between brackets are only for the opposite side ( 6 ) ( 55 ) 56 ( 57 ) ( 59 ) ( ) ( 7 ) ( 53 ) 50 ( 5 ) 6 67 ( 68 ) 66 9 ( 0 ) 69 7 ( 8 ) 7 73 ( 7 ) 55 Body Shell No Body Pin (Large) Body Pin (Small) Part bags used. 7

28

29 Safety Precautions MEMO 9

30 OPERATING YOUR MODEL SAFELY In order to avoid accidents and personal injury, be sure to observe the following: Since exhausts and fuel vapors are noxious to health, use fuel only outdoors! Keep hands and objects away from rotating engine parts to avoid personal injury. Because after running the engine, the engine and the muffler are extremely hot, beware of getting burned! For accident prevention, do not run your model under Only use glow fuel for radio control models! Never use the following circumstsnces: gasoline or kerosene which might cause accidents such as fires! In place where many people gather. Near residential districts, schools and hospitals. Because fuel is highly inflammable, never use fuel indoors, near any source of heat, open flames or even Near roads, railroads, air corridors and electric lines. sparks! Do not dispose of an empty fuel can into a fire. It might explode causing serious injury! Also make sure that nobody is using the same frequency as you do at the same time! Be particularly careful not to swallow fuel or to get fuel When the radio batteries are empty. into eyes! Nevertheless, should fuel be swallowed, immediately induce vomiting and call a physician. Should fuel get into eyes, thoroughly rinse the eyes and seek medical advice. When the model's control or running behavior is strange. Always store fuel in a safe place out of children's reach with the cap shut tight! The place for storage should be dark, cool and dry! 30

31 GSR EXPLODED VIEW B BL B B B B BB 650- No Needle Valve Set Shim Piston Pin Recoil Starter Carburetor Stopper Dust Cover Carburetor Seal O-ring & Shim BB 650-3BL Recoil Starter Assembly Part Names Connecting Rod Oneway & Shaft Set Back Plate No B Part Names Screw Set For Japanese market only! 00 GS-R 300 Crankcase (GS-R) GS-R Cylinder Head (GS-R) 800 GS-X & GS-R 00 Head Gasket (GS-X & GS-R) GS-R Piston & Cylinder Set (GS-R) Carburetor & Valve Set 800 Back Cover Carburetor Assembly (8mm) 50 Flywheel Spacer Crankshaft 800 3

32 E I FANTOM SPORTS / EXPLODED VIEW < > Parts indentified only by key numbers are not sold individually! Parts number in brackets are for replacement C D G H F I J A B Clutch A K K B C Clutch Shock Front Rear Shock (Rear) Gear Gear Pulley (7T) Pulley (7T) Pulley (7T) Receiver Holder Receiver Holder Linkage Linkage Shock (Front) F G D J H E FM-3 3 FM-3 OT-9 8 OT-9 8 OT-9 8 OT-9 8 OT FM-37B FM-37B (L) FM-30 5 (R) 6 FM FM-39 FM-360 FM (FM-39) 90 9 (L) FM (R) 8 (L) FM-300- (R) FM-30(L) 9 FM-303(R) 0 FM-30(L) 7 FM-303(R) 8 (L) FM-308 (R) 3 FM-30(L) 5 FM-303(R) 6 UM-8 99 FM-30(L) FM-303(R) FM FM-30(L) FM-303(R) 3 FM FM-36 FM FM FM ( ) 7 (FM-37) 8 6 ( ) 38 UM-8 99 FM KP/KY FM FD-65 6A FM-37 8 FM-37 8 FM FM-3 8 LA FM FM-3 3 FM-3 9 FM-383 FM FM FM-39 3 FM (70KY) FM FM FM FM FM FM-36 6 FM FM FM FM FM-9 83 FM FM FM FM FM-3 8 FM FM-3 8 FM FM FM-33-FL 3 FM-33-FU FM-3 3 FM FM-9 83 FM-33 -RU (FM-338) 0 (FM-337) 03 FM-3 9 FM FM-38 5 FM-33 8 (FM-3) 8 FM FM (9689) (FM-370) 56 UM- 73 UM-8 99 UM- 73 UM-8 99 (FM-337) 03 (FM-337) 03 FM-3 9 FM-3 9 (FM-338) 0 (FM-338) 0 (FM-338) 0 (FM-338) 0 FM (9689) (9689) (9689) FM-383 FM FM-3 FM-3 FM FM-3 85 FM-3 85 (FM-337) 03 FM-3 9 (FM-337) 03 FM-3 9 FM FM-307 (L) FM-30 3 (R) (606) 35 (60) FM-3 83 (FM-30) 8 FM-30 7 (FM-3) 6 FM FM FM FM-30 6 FM FM-39 9 FM FM FM (967) 36 (967) FM-38 FM FM FM FM-36-8L 79 FM-363-H 80 FM FD-65 6B 6D FM FM FD FM FM FM FM FM UM- W-56 (FM ) 73 7 E B B A A C C D D (FM ) 55 FM-3 FM-387 FM-357-0H 30 FM-356-6L FM FM-386 FM CB FM-387 UM W-56 (70KY)

33 SPARE PARTS () FOR JAPANESE MARKET ONLY. No. No. No. Part Names Quantity No. Part Names Quantity FM FM-3 Knuckle Arm One-touch Spring x Optional Parts FM-300 Knuckle Arm x FM-33 - Front Upper Suspention Shaft x 50 -FU FM-30 FM-30 Rear Hub 3 x FM-33 Front Lower Suspention Shaft 3 x -FL Front Suspension Arm (Left) x 3 x FM-33 Rear Upper Suspention Shaft x -RU FM-303 FM-30 Front Suspension Arm (Right) x 3 x FM-3 Roll Bar FM-356 6T Rear Upper Arm 5 6 x 50-6L st Gear (6T) 6 x 9 x FM-305 FM-306 FM-356 7T Rear Lower Arm 7 8 x 9 x 550-7L st Gear (7T) Optional Parts 700 FM-356 8T Front Wheel 0 x -8L st Gear (8T) Optional Parts 700 FM-307 FM-357 0T Rear Wheel x -0H nd Gear (0T) 30 x 700 FM-308 FM-309 FM-30 FM-357 T Front Bulkhead 3 x -H nd Gear (T) Optional Parts 700 FM-357 T Rear Bulkhead 5 x 98 x -H nd Gear (T) Optional Parts 700 3x6mm Rear Bulk Support 6 7 x 350 FM-359 st Housing 3 x 3x6mm F/H Screw x FM-3 Fuel Tank 8 x x FM-360 nd Shoe Set.6xmm x.6xmm Cap Screw x 800 FM-3 Rear Body Mount 3 9 x E E.5 x 3 xmm 36 x 3 E-ring (E.5) FM-36 nd Shoe Holder xmm x FM-33 FM-36 8T Center Bulk 37 x 38 x 350-8L st Spur Gear (8T) Optional Parts x FM-36 9T FM-3 Small Parts Set 00 8 x 9 x 0-9L st Spur Gear (9T) 79 x 00 FM-363 T FM-35 Front Bumper 50 x -H nd Spur Gear (T) Optional Parts 650 FM-363 5T x FM-36 Pulley Set -5H nd Spur Gear (5T) 80 x x FM-368.7mm FM-37B 97 x Servo Saver x -.7 Front Spring (.7mm) Optional Parts FM-368.8mm FM-30 Front Wheel Shaft 8 x Front Spring (.8mm) 5 x FM-368.9mm FM-3 Rear Wheel Shaft 8 x Front Spring (.9mm) Optional Parts FM-368.0mm FM-3 Front Swingshaft 83 x Front Spring (.0mm) Optional Parts FM-369.7mm FM-33 Rear Swingshaft 8 x Rear Spring (.7mm) Optional Parts FM-369.8mm 3x0mm FM-3 3x0mm Parallel Pin 85 x Rear Spring (.8mm) 53 x FM-369.9mm FM-35 Front Cup Joint 86 x -.9 Rear Spring (.9mm) Optional Parts L=68 C FM-370 FM-36 Front Shaft 87 x C-ring x 00 Adjustable Rod (L=68) 56 x 650 FM-37 FM-37 Middle Shaft 88 x 300 Linkage Set x 63 x x x FM-373 FM-38 Main Saft 3x0mm 000 Muffler Holder Set xmm x0mm 50 3x0mm Cap Screw x xmm,, x0mm F/H Screw x x 8 x C FM-39 Rigid Axle 90 9 x C-ring x 000 FM-37 Fuel Tank Post 3x6mm 350 3x6mm F/H Screw x E E-7 9 x E-ring (E-7) x 0.5 FM-376 FM-330 Pulley Adapter 50 Axle Washer (0.5) 86 x xmm xmm x 3 FM-377 Front Belt 3 87 x 800 xmm FM-33 Pulley / Brake Adapter 93 x xmm x FM-378 Middle Belt 0 88 x 700 FM-33 Brake Cam x 00 0 FM-379 Rear Belt 0 89 x 900 FM-337 9mm 9mm Ball Screw 03 x 900 FM-338 0mm 0mm Screw Cap 0 x 00 3

34 SPARE PARTS () FOR JAPANESE MARKET ONLY. No. No. No. Part Names Quantity No. Part Names Quantity FM-383 Plastic Parts (Sports) 5 38 x 6 x x 6 x x FM-38 Rear Lower Suspention 0 x Shaft (Sports) 5 x 50 FM-385 Main Chassis (Sports) 7 x 390 3x0mmTP 3x0mm TP F/H Screw x 5 /8 Body Set x8mm0 GS FM-386 Flywheel (GS) x 00 (/8 CASTROL SUPRA) x8mm R/H Screw x 6 3x0mmTP E E9.0 3x0mm TP Bind Screw x 9 FM-387 Pilot Shaft (GS) GS x E-ring (E9.0) x 50 mm 5x0x0.5mm mm Nut x 6 5x0x0.5mm Washer x x6x0.mm FM-388 x6x0.mm Washer x 0 Clutch Bell 8 x 000 FM-389 Upper Plate Instruction Manual x (Sports) 8 x FM Decals /8 (/8 CASTROL SUPRA) 03 x 300 Middle Shaft Collar x Muffler Joint Pipe 000 FM-39.8mm 33 x.8mm Linkage Ball End 9 x Snap Pin 00 FM-39 5 x 0 Muffler 30 3 x 000 E E.5 96 Suspension Shaft 50 FM x E-ring (E.5) x Manifold 3 x mm mm Ball Nut FM-39 Brake Set (Sports) 0 x x 6x3x5mm x3x5mm Ball Bearing 700 CB-0 67 x Air Cleaner 6 7 x 8 x 6xxmm 967 6xxmm Ball Bearing 36 x 000 FD-65 Linkage Set 6A x 6B 6C x 00 5x7mm x7mm Sim Set 9 x 0 50 FM-9 Body Pin 83 x 0 50 xx5mm 9689 xx5mm Ball Bearing 68 x 000 LA-0 Belt Roller 3 x 50 OT-9 O O-ring P3 (P3) 8 x mm UM-.8mm Ball End 7 73 x Some of the parts included are not available as spare parts. Purchase optional parts instead..8mm UM-8.8mm Ball Stud 99 x 00 UM-0 Clutch Shoe 5 x set 00 A B C D E W-56 SS x Racing Shock SS 00 E E.5 E-ring (E.5) x 39 C C C-ring (C) x KP S Fluorescent Nylon Strap Pink (S) x KY S Fluorescent Nylon Strap Yellow (S) x KP M Fluorescent Nylon Strap Pink (M) x KY M Fluorescent Nylon Strap Yellow (M) x Antenna Pipe 73 x Rod Stopper 6 x x0xmm 5x0xmm Ball Bearing 33 x GP0 Gasket for Manifold (GP0) 3 x

35 OPTION PARTS () FOR JAPANESE MARKET ONLY. No. No. No. Part Names Quantity No. Part Names Quantity 30 W-509 Damper Oil Decal TYRE (F) Standard Pit Box TYRE (F) Standard TYRE (F) Standard Precision Camber Gauge TYRE (F) Standard Team 30 Team Silicone Fuel Tube(Clear) TYRE (F) Multi Dust Creaner TYRE (F) Multi TYRE (F) Multi Molybdenum Coat TYRE (F) Multi V-mAh 6V-mAh NiCd-Battery TYRE (R) Standard Locktite (Medium Strength) TYRE (R) Standard x6mm x6mm Sim Set TYRE (R) Standard Silicone Oil # TYRE (R) Standard Silicone Oil # Silicone Oil # TYRE (R) Multi TYRE (R) Multi Silicone Oil # TYRE (R) Multi Silicone Oil # SP 7mm Silicone Oil #700 FMW- SP Rear Sus Holder (7mm) 800 SP 6mm Silicone Oil #800 FMW- SP Rear Sus Holder (6mm) 900 SP 8mm Silicone Oil #900 FMW-3 SP Rear Sus Holder (8mm) Silicone Oil #000 FMW SP Tornade Fuel.5L Tornade After Run Oil 3 FMW-8 FMW-9 SP 0 SP 0 SP Rear Belt (0) TYRE (F) Standard FMW Front Spring (-.8) 35 TYRE (F) Standard FMW Front Spring (-.9) 37 TYRE (F) Standard FMW Front Spring (-.0) 0 TYRE (F) Standard 0 00 FMW Rear Spring (5.3-.8) 30 TYRE (F) Multi 30 FMW Rear Spring (5.3-.9) 35 TYRE (F) Multi 35 FMW Rear Spring (5.3-.0) 37 TYRE (F) Multi 37 FMW- L Front Spring L (.5-.8) 0 TYRE (F) Multi 0 FMW- L Front Spring L (.5-.9) 30 FMW- L.0-.0 TYRE (R) Standard 30-0 Front Spring L (.0-.0) 35 TYRE (R) Standard 35 FM-38 Decal Set decals x TYRE (R) Standard 37 0 TYRE (R) Standard 0 30 TYRE (R) Multi TYRE (R) Multi TYRE (R) Multi 37 0 TYRE (R) Multi

36 OPTION PARTS () FOR JAPANESE MARKET ONLY. No. No. No. Part Names Quantity No. Part Names Quantity ASSY FM-38 FM-38F Front Shock Assembly Front One-touch Stopper Made of Aluminum 5.8mm FM-39 Rear One-touch Stopper FM mm Ball Screw 900 Made of Aluminum Use Together.8mm FM-33 Brake Disk 00 UM-.8mm Ball End 300 Use Together ASSY FM-333 Brake Pad 00 FM-38R Rear Shock Assembly 300 FM mm Front Stabilizer Set 00 FM mm Ball Screw Use Together 900 FM-335 Body Mount Screw 900 UM-.8mm.8mm Ball End 300 FM-3 5.8mm 5.8mm Ball 00 FM Rear Stabilizer Bar (.6) 00 FM Rear Stabilizer Bar (.9) 00 FM Rear Stabilizer Bar (3.) 00 SPW-5 Use Together Adjuster Rod Set mm 5.8mm Ball End x8x.5mm 5x8x.5mm Ball Bearing mm 3.0mm 5.8mm Hard Ball Joint (w/3.0mm hole) mm 3.mm 5.8mm Hard Ball Joint (w/3.mm hole) 800 Needed parts for other engine than GS. Available optional parts for Fantom. No. No. No. Part Names Quantity No. Part Names Quantity FM-36 FM-380.mm UP Engine Mount 800 FMW- Body Stiffener (.mm) Gives strength of body. ASSY Use Together.5mm UP Clutch Assembly 8 FMW-5 Body Stiffener (.5mm) Gives strength of body FMW-6 Rear Spoiler 000 GS Needed parts for Fantom (GS engine is not available.) FMW-5 L Rear Spring L (.8-.8) Long Size No. FMW-5 L.8-.9 No. Part Names Quantity -89 Rear Spring L (.8-.9) Long Size FM-35 5mm-7075 L.8-.0 Main Chassis 9800 FMW-5 5mm thick-7075 Duraluminium -80 Rear Spring L (.8-.0) Long Size FM-37 Tensionner Set With Ball Bearings /8 Arrows Rear Spoiler 000 FM-375 Radio Plate Made of Carbon Fiber L VDS S P/8 VDS Lola SP (/8 Light) 3000 OPTION PARTS () are all needed for Fantom. 37

37 No. mm Size (mm) QUANTITY No. Round Head Screw 00 SCREW NUT etc. FOR JAPANESE MARKET ONLY. mm Size (mm) QUANTITY No. mm QUANTITY Round Head Self-Tapping Screw 00 Nut 00 Flanged Nut 00 Bind Screw 00 Flat Head Screw 5 each 5 each 5 each 5 each 5 each 5 each 00 Bind Self-Tapping Screw 00 Flat Head Self-Tapping Screw 00 Nylon Nut 00 Flanged Nylon Nut 00 Washer 00 Flanged Cap Screw 00 E E-Clips 50 Cap Screw 00 Oval Head Screw x8x0 0 each 00 Spring Washer 00 R THE FINEST RADIO CONTROL MODELS TEL ( PRINTED IN JAPAN