p01.pdf
|
|
- えみ たにしき
- 6 years ago
- Views:
Transcription
1 RADIO CONTROLLED ELECTRIC POWERED WD RACING BUGGY INDEX SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE. C KYOSHO 000
2 R REQUIRED FOR OPERATION () ch with electronic speed controller and servo radio control set CAUTION: Only use a surface radio with channels and electronic speed controller! (Any other radio is prohibited!) This kit requires a channel radio control set with electronic speed controller. Because there are stick-type and wheeltype transmitters, use which ever fits your convenience best. For more information on the radio con-trol set, refer to its instruction manual. Stick-type ch radio set Wheel-type ch radio set AA-size Batteries (For Transmitter) Suitable servos, receiver & electric speed controller Servo Receiver AA AA Electric speed controller Operation/Receiver Battery and Charger for Ni-Cd Battery A single Ni-Cd battery powers operation and recei-ver. Batteries listed right are suitable. Use battery charger designed for saddle pack battery. 7.V-RC000 Ni-Cd Battery 7.V-X-FORCE 00 Ni-Cd Battery 7.V-X-FORCE 0 Ni-MH Battery Motor & Pinion Gear Use a 0 size motor & /8 Pinion Gear. Tire / Wheel / Inner Sponge /0 This kit does not supply tires and inner Sponge. Use tires and Inner Sponge for /0 buggies. Paint and Brush For painting the body, use Kyosho paints for models! PAINT BRUSH No.0 POLYCA COLOR No KYOSHO SPRAY COLOR CAUTION: Before using spray colors, always read their explanations! KY OSH O S PR AY CO LO R MICRON LINE TAPE No.8 (mm x m) KYOSHO 8 (.mm x m) 8 (.mm x m) 89 (0.mm x 8m) 860 (0.7mm x 8m) Super-flexible tape for masking and detail designing jobs. Micron Line Tape No.9670 D FLEX COLOR DECAL Self-adhesive super-flexible sheets that bond to polycarbonate - even when applied to curved surfaces. No.97 MASKING SHEET For safe masking jobs, use this plastic masking sheet featuring one self-adhesive edge.
3 REQUIRED FOR OPERATION () Tools required Phillips driver ( L. M. S. ) Sharp Hobby Knife Needle Nose Pliers Wire Cutters CAUTION: Handle tools carefully! Grease Grease Instant Glue TOOLS INCLUDED Hex Wrench Cross Wrench Ball Differential Grease Awl No.80 SPECIAL TAPER REAMER No need to pre-drill! Drills neat mm to mm holes directly! Rubber Cement No.89 ROUND CUTTER & SANDER For trimming bodies! Cutting along curved lines never was so easy! Set up the radio control system as indicated below. RADIO PREPARATION A new Ni-Cd battery must be charged before it is used. Refer to the charger instruction manual for charging. Ni-Cd Battery Charger Electronic Speed Controller 7 ON 9 OFF Transmitter ON OFF Servo START Receiver Install batteries. (Transmitter) Extend the antenna. (Transmitter) Connect the Ni-Cd battery. Extend the antenna. (Receiver) Center the trims. Switch on. (Transmitter) Switch on. (Receiver) Switch Make sure the servos are in command. 9 0 FINISH 9 0 Switch off. (Receiver) Switch off. (Transmitter) Retract the antenna. (Transmitter)
4 BEFORE YOU BEGIN () Read through the manual before you begin, so you will have an overall idea of what to do. Check all parts. If you find any defective or missing parts, contact your local dealer or our Kyosho Distributor. How to read the instruction manual: Front Suspension x 0mm Metal Bushing No., No., No.6 This instruction manual uses several symbols. Please note them during the entire assembly. King Pin 6 6.8mm Pillow Ball (Black) R 7 L 8 Key Number, Part Name, True-to-scale Diagram, Quantity Used All parts except screws are identified by key numbers. For purchasing spare parts, find the key no. of the part needed in the spare part list and refer to the left column to look up the corresponding order no. Symbols used throughout the instruction manual, comprise: Part bags used. mm Drill holes with the specified diameter (here: mm). Must be purchased separately! Apply epoxy glue. Cut off excess. Pay close attention here! Apply instant glue (CA glue, super glue). Cut off shaded portion. Apply rubber cement. Tentatively tighten. Apply grease. Ensure smooth non-binding movement while assembling. Apply threadlocker (screw cement). True-to-scale diagram. x Assemble as many times as specified (here: twice). Assemble in the specified order. Assemble left and right sides the same way. 90 No.90 Ball bearings are optional! (with optional part no.)
5 BEFORE YOU BEGIN () This kit contains screws and hardware in different metric sizes and shapes. Before using them, check the screws on the true-to-scale diagrams on the left side in each assembly step. Some screws are extras. SCREWS OTHER HARDWARE Self-tapping (TP) Washer Nut E-ring Cap TP F/H mm mm mm mm Flat Head (F/H) Set F/H mm Metal Bushing Bearing mm Pillow Ball mm 0mm 6.8mm 6 Self-tapping (TP) screws cut threads into the parts when being tightened. Excessive force may permanently damage parts when tightening TP screws. It is recommended to stop tightening when the part is attached or when some resistance is felt after the threaded portion enters the plastic. Correct Wrong Overtightened. The threads are stripped. ARRANGEMENT OF PLASTIC PARTS ON RUNNERS Shaded Parts are not used. t t R L t 8 t A B B A C B B C
6 Ball Differential No DIFF. DIFF. 6 7 Inside ADJUSTING 0 0 Now, hold the differential case firmly and rotate part 0. If part Secure parts and 0 in place with two flat head screwdrivers rotates into the opposite direction to part 0, no further adjustment and rotate the differential case until it becomes tight. Then, tighten is necessary. If part does not rotate, screw is too tight. In screw. When running the car, the differential must be tight, otherwise it may be this case, gradually loosen screw until part rotates. damaged. 8 Note the direction. 7 x Once the adjustment is done, install and (see"exploded view"). Shock x 6 x mm Plastic Collar 8 x 7 x mm Plastic Collar CC-ring No. 8.8mm L Ball End (L) 7.8mm S Put a little oil. Ball End (S) OO-ring E. EE-ring 8 Fit into groove. 8 O O-ring (M) 0 < for Front > 8 E.mm 0.mm approx. 0.mm < for Rear > 7 -C Front -C -B Rear -B for Front (Short) 6 for Rear (Long) 8mm approx. 8mm E.mm x x Put a little oil. Part bags used. DIFF. Apply grease (or differential grease). Apply instant glue (CA glue, super glue). x Assemble as many times as specified (here: twice). 6
7 Shock No. You can assemble the shock in ways. 9 0,, 9 Complete the shock assembly in the order 0, and 9. 0 for Front (Short) for Rear (Long) 8 for Front (Short) 7 for Rear (Long) Pull down the piston and slowly fill in oil. 0~mm Add oil one more time up to the brim. Move the piston up and down to get rid of air bubbles. Surplus oil comes out. Confirm that each piston moves up and down smoothly. Shock No. Keep expanded. Insert the shaft slowly. 8 for Front (Short) 7 for Rear (Long) Put the oil. 9 Tighten the cap until it slightly stops, then loosen it for a /nd lap. Tighten the cap firmly, and pull the shaft. 9 O O-ring (Large) 9 Surplus oil comes out. Shock No. 6.8mm Ball 8 0 for Front (S) for Rear (L) 6 for Front (S) for Rear (L) For adjusting the spring tension. 6 exists in widths. For making the F / R ground clearance horizontal, choose the necessary width(s) and amount of. When adjusting, run your car. 7 Compress the spring and install x Part bags used. Assemble as many times as specified. Must be purchased separately! 7
8 6 Chassis No. x 8mm F/H 7 Flanged Nylon Nut 7 x8mm 7 Front Suspension No. No.6 x 0mm TP 6 x0mm 8 Front Suspension No. No. x 0mm TP 70 x 0mm Adjustable Rod E.mm x0mm x 8mm 9 E. E E-ring 68.8mm Ball End (Medium) x0mm Suspension Shaft (Black) 8 x 6 x mm Plastic Collar 7 Front Note the direction. 6mm The side with the step is a reverse screw. Part bags used. Cut off shaded portion. Tentatively tighten. Assemble left and right sides the same way. 8
9 9 Front SuspensionFront No. 7 x mm TP F/H 8 0 xmm(tp) 0 Front SuspensionFront No. x8mm x 0mm TP x0mmtp 7 x 8mm Front SuspensionFront No. 8 x 8 mm F/H x 8mm SIM Right mm mm(black) Right 80 mm 8 mm.6mm 78 Part bags used. Cut off shaded portion. Tentatively tighten. Assemble left and right sides the same way. 9
10 Front SuspensionFront No. No. x 0mm TP x mm TP F/H 8 9 x8mm x mm x 8mm Cap x0mm mm Nut mm Washer 7 87 xmm F/H E. EE-ring 86 Suspension Shaft (Silver) 8 mm xmm Rear Gearbox No.6 x mm Set xmm F/H x8mm 9 x mm x 8mm x0mm 9 9 E. x 0mm x mm F/H E. EE-ring O-ring xmm 9 9 E EE-ring 00 OO-ring 6 8 x mm 9 x 6 x 7mm Aluminum Collar 9 Gearbox Spacer 96 E xmm 97 9 x 6mm Bearing Stopper mm Washer 6 Part bags used. Cut off shaded portion. Tentatively tighten. Assemble left and right sides the same way. 0
11 Rear Gearbox No. No. No.6 E. x8mm xmm x8mm If the ball bearings do not fit in easily, file off the edges xmm E. EE-ring 7 0 x8mm x7mm 0 x8mm x 8mm TP x 8mm 9 x 6 x 7mm Aluminum Collar 0 xmm x mm x mm 98 mm Shim 8mm Shim x 7mm x 8mm 6 8 x mm Rear Shock Stay x 8mm Cap x 0mm TP x mm mm No..6 x mm TP mm Nut x mm Set Nylon Nut 7.8mm S Ball Stud (S) xmm 6 8 mm xmm 0mm xmm mm Nylon 6 mm x8mm x0mm 7 0 mm Nylon 0 Part bags used. Cut off shaded portion. Tentatively tighten. Assemble left and right sides the same way.
12 6 Rear Gearbox No. No.6 x 8mm TP x 0mm TP x 0mm TP F/H 0 x0mm F/H x8mm mm x8mm x0mm 9 9 x0mm F/H 9 9 x0mm F/H 9 7 No. No. x 0mm Adjust Rod < Left > 69 (Long) 69 (Long) 8.mm The side with the step is a reverse screw. < Right > 69 (Long) Projection. Note direction. 69 (Long) Part bags used. Cut off shaded portion. Assemble left and right sides the same way.
13 8 Rear Suspension No. No. 80 x 0mm E. E x mm x 0mm TP E-ring Set 7.8mm S Ball Stud (S) x8mm x 8mm TP.8mm L Ball Stud (L) x mm F/H 8 9 mm Flanged Nylon Nut xmm(f/h) 6 x0mm xmm x0mm 80 x0mm 80 xmm(f/h) 8 mm Main Gear.6 x 6mm No. No.6 x 8mm.6mm mm.6mm Tighten.6mm screw x mm 0 x 8mm Thrust Plate x 8mm Bushing mm Nylon Nut 9 Trim to fit 9. Do not cut off too much! 9 xmm xmm 0 mm.6x6mm 0 * 9 GEAR RATIO * * ** : not available at Kyosho. 8 7 Part bags used. Cut off shaded portion. Assemble left and right sides the same way.
14 0 No. No.7 < Left > 68 (Medium) 69 (Long) x 0mm Adjust Rod mm 0 x mm Adjustable Rod < Right > 69 (Long) Projection. Note direction. 68 (Medium) 68 (Medium) 0 68 (Medium) The side with the step is a reverse screw. 7mm.6 x mm TP.6 x mm F/H x 6mm F/H () 60 7 No. No mm.6mm mm C Use according to the servo used. 66 x 0mm TP F/H x 0mm TP mm Nylon Nut.6mm Washer ().6mm C A 60 9 mm B xmm(TP) Futaba x0mm(tp) KO, Sanwa 6 A mm B x6mm x0mm(f/h) Part bags used. Cut off shaded portion. Assemble left and right sides the same way.
15 Chassis x 6mm F/H x 8mm x 0mm TP 6 No. No.7 7 x8mm 6 Unscrew the screws temporarily tightened, and attach 6 with them. x8mm 8 x0mm x8mm Location for receiver 6 7 Black x 0mm TP F/H 6 67 Note the direction. x0mm (FH) 7 Location for electronic speed controller x6mm( F/H) 7 Black Body Shell Magic Tape (hard side) 69 mm 7 Black 7 76 Magic Tape (soft side) Black 70 Part bags used. Cut off shaded portion. Must be purchased separately! mm Drill holes with the specified diameter (here: mm).
16 TRUE-TO-SCALE DIAGRAM 68.8mm Ball End (Medium) 0 x mm Shaft 8 x 6 x mm Plastic Collar mm Ball End (Long) 8 x 0mm Shaft 78 x 8 x mm Plastic Collar 0 8.8mm L Ball End (L) 86 Suspension Shaft (silver) 79 x 8 x mm Plastic Collar mm S Ball End (S) 6 8 x mm 7 Suspension Shaft (black) x 0mm Adjustable Rod 0 x mm Adjustable Rod x 9 x 9mm Plastic Collar x 8 x.7mm Plastic Collar mm Plastic Nut x 0mm 70 x 0mm Adjustable Rod Bearing Stopper x 7mm x 8mm.8mm L Ball Stud (L) 7.8mm S Ball Stud (S) x 7 x mm Aluminum Collar 0 0 x 8mm 8 King Pin Ball mm Tapered Collar x 6mm 8 L King Pin (L) mm Stopper 0 60 x 6mm Flanged 7 Steering Pin 9 x 6 x 7mm Aluminum Collar mm Shim 6.8mm mm Ball (mm hole) 9 Gearbox Spacer mm Shim Stabilizer Ball 8 Servo Saver Shaft mm Shim 0 Thrust Washer (thick, copper) Upper Deck Post 0 7 Hook Pin Thrust Washer (thin) 0 0 6
17 OPERATING YOUR MODEL SAFELY WARNING: Do NOT operate the model in the following places and situations: (Non-observance may lead to accidents!) Operate the model in spacious areas with no people around! Do NOT operate it:. on roads!. in places where children and many people gather!. in residential districts and parks!. indoors and in limited space! * Non-observance may account for personal injury and property damage! Always check the dry batteries in the radio! When the dry batteries get weaker, transmission and reception of the radio decrease. You may lose control of your model when operating it under such condition. This may lead to accidents! Keep in mind that people around you may also operate a radio control model! NEVER share the same frequency with somebody else at the same time! Signals will be mixed and you will lose control of your model. 0 This may lead to accidents! When the model is behaving strangely...! Immediately stop the model and check the reason. As long as the problem is not cleared, do NOT operate it! This may lead to further trouble and unforeseen accidents! Do NOT put fingers or any objects inside rotating and moving parts! Rotating / moving at high speed, you may be seriously injured! After operation, the electric motor and Ni-Cd battery are hot! You may burn yourself seriously touching them! WARNING: in order to avoid accidents and personal injury, be sure to observe the following: Before charging, please carefully read the explanations of the Ni-Cd battery and charger unit! While charging, the Ni-Cd battery and charger unit get hot! NEVER charge on top of or near easily inflammable material as this will result in fires! NEVER short out Ni-Cd batteries!. Do NOT disassemble or modify Ni-Cd batteries!. Ensure the cords do NOT trail into rotating and moving parts! Ni-Cd batteries use heavy metals that are noxious to health! NEVER throw them into fires as they will explode! ALWAYS return disused Ni-Cd batteries to the shop! Do NOT dispose of them into the usual waste stream! 7
18 BATT. BATT. BATT. BATT. BATT. BATT. BATT. / PROPER OPERATING PROCEDURES Fully charge the Ni-Cd battery. Check the transmitter batteries. Make sure the throttle control is in neutral. CH- CH- CH- CH- Connect the Ni-Cd battery. Extend the transmitter antenna. 6 Switch on the transmitter. ON CH- CH- CH- CH- OFF ON Switch on the receiver. Make sure the model steers according to your transmitter inputs. Make sure the speed (electric speed controller) changes according to your transmitter inputs. ON CH- CH- CH- CH- 0 Make sure the running area is safe. / AFTER FINISHING RUNNING After finishing running, collect your car. Do not leave on the racing car. STOP Switch off the receiver. OFF Switch off the transmitter. CH- OFF CH- ON OFF Disconnect the Ni-Cd battery. Remove dirt from the chassis. OFF CHECK When NOT using the model, always switch off the receiver and transmitter! Furthermore, disconnect the Ni-Cd battery and remove it from the model! This may lead to overheat and fires! 8
19 TROUBLESHOOTING Steering control servo does not operate. Transmitter and/or receiver is not switched on. Transmitter batteries are weak. Improper radio installation. Switch on. Replace with new batteries. Correct as per radio instruction manual. Motor does not run. Ni-Cd battery capacity is insufficient. Improper radio installation. Loose connectors. Motor trouble. Recharge Ni-Cd battery. Correct as per instruction manual. Make connectors tighter with minus screwdriver. Replace with a new motor. Motor runs but car does not run. Pinion gear is not installed. Or, screw is loose. Tighten screw that holds pinion gear. Not enough speed. Wheels hardly rotate/do not rotate at all. Ni-Cd battery capacity is insufficient. Electronic speed controller is not properly adjusted. Dirt entered rotating parts on wheels. Backlash is too tight. Recharge Ni-Cd battery. Adjust throttle trim (transmitter). Should electronic speed controller not shift into high, readjust it as per instruction manual. Clean and regrease. Readjust as per instruction manual. Even when releasing throttle, car does not run. Electronic speed controller is not properly adjusted. Adjust throttle trim (transmitter). Should electronic speed controller not shift into high, readjust it as per instruction manual. 9
20 SPARE PARTS No. No. Part Names Qty. KC-8 mm 00 x 0 60 mm Stopper LA- Differential Case Set 7 8 x 00 LA- /8 Thrust Ball /8 6 x 80 LA- 0 0 x Drive Pulley Set LA-0 Suspension Shaft Set 8 0 x 86 x 0 LA- (L) King Pin (L) 8 x 0 LA- Steering Pin 7 x 0 LA- x 8 x Servo Saver Shaft Set LA- Velcro Tape 76 x LA-.8mm.8mm Ball End 8 x 00 LA x Front Bulk Set LA-0 A- A-Arm Stay x,00 LA x Bumper Set x 6 x 0 LA-0 ( ) Suspension Arm Set (graphite) LA-0 Upper Deck LA-07 Rear Bulk Set LA-08 Plate Set LA-09 Transmission Plate LA-0 Rear Side Plate LA- Gear Cover 88 x 6 x x x 9 x 0 x x LA- 9 x 9 x 9 x6 Transmission Post Set LA- 7 x Front Belt LA- Rear Belt LA-6 Center Oneway Pulley LA-8 Hyper Disk Plate LA-9 Hyper Clutch Thrust Set LA- (ZX-S) Body Set (ZX-S) LA- Wing Set LA- LA- Stabilizer Parts (LAZER ZX-S) Decal (LAZER ZX-S) LA-6 Main Chassis LA-7 Battery Plate x 0 x 9 x x 0 x x 70 x 0 x,00,000 00,000, ,800,00 0, x 700 x x, x,600 LA x 79 x 78 x 600 LA-9 8 x.8mm King Pin Ball LA-0 Motor Cooling Plate 99 x 00 x LA- Sus Plate Set 87 6 x LAW x Hyper Clutch Set LAW-- () Main Shaft(Hyper Clutch) 96 x LAW-0- Skid Plate x LAW- x Front Shock Stay 0,00 0,00 800,000,000 LAW- Rear Shock Stay LAW- FOR JAPANESE MARKET ONLY. No. No. Part Names Qty. Steering Plate(C) OT-6 Knuckle Arm OT-9 Drive Washer OT-.8.8mm Ball OTW-9 Plastic Parts OTW-0 Unicrank Servo Saver OTW- (S) Adjust Rod (S) OTW- (M) SP- SP-07 Rear Hub Carrier 6 x,00 SPW- 70 x Adjuster Rod Set SPW-6-6 x Setting Stabilizer Bar Set UM- 8 x Slipper Pad UM- x Servo Saver Strong Ring UMW x Wing Stay Set.8mm UM-.8mm Ball End Cap UM- UM-8 UM-9 Adjust Rod (M) Small Plastic Parts Set Tensionner Spring.8mm (L).8mm Ball Stud (L).8mm (S).8mm Ball Stud (S) 9 x 7 7 x 8 x 6 x 0 6 x x 0 x x 66 x 7 x x 6 x x 7 x UM- mm Outer Front Hinge Pinmm 86 x 0 UM-6 6mm Outer Rear Hinge Pin 6mm 7 x 0 UM- 86T/8P Spur Gear 86T/8P x 0 M W-0 x 0 M Taper Washer 0 W-0 mm x 6 Aluminum Color mm 0 W-0 Shock End 7 x 00 W-07 Shock Diaphragm 0 x 0 00 W-06W (6 ) Narrow Wheel(6 Size) 7 x 0 W-07W (6 ) Wheel(6 Size White) 7 x 0 W-06 x Universal Swingshaft,00 W-06 (L) Universal Swingshaft (L) 89 x,00 W x Plastic Parts (Equalizer) 0 W-9 Setting Spacer 00 W-8 (S) Twin Cap Pro Shock(S),00 W-8-0 Shock End Cap 9 x 0 W-8-0 Lower Shock Cartridge 0 x W-8-0 Shock Pistons x x x 8 00 W-8-0 (S) Shock Seal O-Ring(S) x 0 W-8-0 (M) Shock Seal O-Ring(M) 9 x 0 00 TEL
21 No. No. Part Names Qty. W-8-06 x x 0 Shock Rebuild Set W-8-07 (S) Teflon Shock Case(S) 8 x 900 W-8-08 (S) Shock Shaft(S) x 600 (S) #60 W-8-60 Spring(S)#60 0 x 0 W-8-0 (M) Shock Shaft(M) x 600 W-8-0,W-8-0 W-8 (L) Twin Cap Pro Shock(L),00 (L) W-8-0 Teflon Shock Case(L) 7 x 900 (L) #6 W-8-6 Spring(L)#6 x 0 WBD- Pressure Plate x WBD Ball Diff. Shaft Set,00 WBD-6 x x0 x Ball Diff. Thrust Set 600 WBD-9 /6 Thrust Ball /6 x ( ) Color Antenna (white) 7 x x 0mm 80 x x 0mm 700 No. Part Names Description LA SPW- Toe Angle Adjuster Plate (Rear) UM-6 (6 T-8P) Steel Pinion Gear (6 T-8P) UM-09 (RB) Wing (RB) UMW-0 mm Hard Hinge Pin mm UMW-0 6mm Hard Hinge Pin 6mm UMW-0 (EP ) Light Slipper Disk(for EP) W-07 (7 T-8P) 0 Hard Pinion Gear (7 T-8P) W-06.8 (M.0).8 Hard Ball (M.0) W-06 (6 ) Narrow Wheel(6 Size Yellow) W-07 (6 ) Wheel (6 size Yellow) W-08 (6 ) Inner Sponge (6 size, high traction) W-0BK () Shock Cap Set (Black) W-0BL () Shock Cap Set (Blue) W-0G () Shock Cap(Gpld) W-0P () Shock Cap Set (Purple) W-0R () Shock Cap Set (Red) SPARE PARTS() OPTIONAL PARTS , FOR JAPANESE MARKET ONLY. No. No. Part Names Qty. x 8mm 90 x 700 x 8mm x 8mm 90 x 700 x 8mm 8 x mm x mm 6 x 906 (PureTen) Ball Differential Set (PureTen) FOR JAPANESE MARKET ONLY. No. Part Names Description W-8-09 (S) #70 Spring(S)#70 W-8- (S) # Spring(S)# 0 W-8-7 (S) #7 Spring(S)#7 0 W-8-0 (L) #70 Spring(L)#70 W-8-60 (L) #60 Spring(L)#60 0 W-8-7 (L) #7 Spring(L)#7 0 W-8-80 (L) #80 Spring(L)#80 0 W-88 Teflon Piston(No Hole) W-60 H-( ) H-Pin Narrow Tire (high traction) W-60 H- ( ) H-Pin Tire (high traction) W-60 ( ) Micro Block Narrow Tire (high traction) W-60 ( ) Micro Block Tire (high traction) W-606 (6/) Narrow Wheel(6 Size /Mesh) x x x 8 6 x 0 96 Special Unicrank x 60 x 968 Snap Pin 7 x 0 96 (mm) Foam Tape (mm) 7 x 967 x 6mm x 6mm 9 x 969 x 7mm x 7mm x 966 x 6mm x 6mm Shim Set 98 (0., 0., 0.mm) x x 7mm x 7mm Shim Set (0., 0., 0.mm) x x 0mm (0., 0., 0.mm) x 0 8 x 0mm Shim Set 9669 x 6mm x 6mm Flanged Bearing x W-606 (6 /) Wheel (6 size /Mesh) Silicone Oil cc, ,
22 () () (), ,680 () () ()
23 7
24 R THE FINEST RADIO CONTROL MODELS -00 TEL ( ) PRINTED IN JAPAN
P001.pdf
Before commencing assembly, please read these instructions thoroughly. WINGSPAN : 195mm R THE FINEST RADIO CONTROL MODELS EP CESSNA 180 TRAINER INSTRUCTION MANUAL RADIO CONTROLLED ELECTRIC POWERED AIRCRAFT
More information32720_MR-03_JSCC_CUP
Before beginning assembly, please read these instructions thoroughly. THE FINEST RADIO CONTROL MODELS R MINI-Z Racer MR-03 Chassis Set ASF.4GHz JSCC CUP Edition Thank you for purchasing the Chassis Set
More informationp01.pdf
Before beginning assembly, please read these instructions thoroughly. R THE FINEST RADIO CONTROL MODELS ELECTRIC POWER EPVERSION INSTRUCTION MANUAL :0 SCALE RADIO CONTROLLED ELECTRIC POWER WD RACING BUGGY
More informationKyosho Pure Ten EP KX-One Manual
Before commencing assembly, please read these instructions thoroughly! R THE FINEST RADIO CONTROL MODELS INSTRUCTION MANUAL RADIO CONTROLLED ELECTRIC POWERED TOURING CAR SERIES PureTen EP WD CHASSIS KIT
More informationP001.pdf
Before commencing assembly, please read these instructions thoroughly! R THE FINEST RADIO CONTROL MODELS INSTRUCTION MANUAL RADIO CONTROLLED ELECTRIC POWERED TOURING CAR SERIES PureTen EP WD CHASSIS KIT
More informationP12_InstructionManual.pdf
1 BAG 1 CHASSIS PREPARATION OPEN BAG 1 1 SEAL THE EDGES OF GRAPHITE PARTS FOR PROTECTION SANDPAPER USE SANDPAPER TO SAND SMOOTH THE EDGES C20001 Rapide P12 2.5mm Graphite Main Chassis CA GLUe APPLY CA
More informationp01.pdf
Before use, please carefully read the explanations! R THE FINEST RADIO CONTROL MODELS INSTRUCTION MANUAL LENGTH : 630mm (5") RADIO CONTROLLED ELECTRIC POWERED CRUISER INDEX REQUIRED FOR OPERATION BEFORE
More informationKyosho Ultima GP ST Type-R Manual
Before commencing assembly, please read these instructions thoroughly. THE FINEST RADIO CONTROL MODELS R GAS POWERED GPVERSION INSTRUCTION MANUAL :0 SCALE RADIO CONTROLLED.-.5 ENGIE POWER WD STADIUM TRUCK
More informationuntitled
OREC ISSUED NO. SP1000-1 Parts catalogue Spider Mower (EXPORT MODEL) SP1000 MODEL CODE SP1000 0202- CONTENTS HANDLE 1-8 DRIVING & CUTTING 9-12 CHAIN CASE 13 TRANSMISSION 14-22 GEAR FRAME 23 FRONT WHEEL
More informationp01.pdf
*Before beginning assembly, *please read these instructions thoroughly. R THE FINEST RADIO CONTROL MODELS INSTRUCTION MANUAL :8 Scale Radio Controlled Electric Powered WD Monster Truck TWIN FORCE INDEX
More informationP001.pdf
Before commencing assembly, please read these instructions thoroughly! Radio Controlled. Engine Powered Touring Car Series THE FINEST RADIO CONTROL MODELS R INSTRUCTION MANUAL INDEX REQUIRED FOR OPERATION
More informationp01.pdf
Before beginning assembly, please read these instructions thoroughly! THE FINEST RADIO CONTROL MODELS R INSTRUCTION MANUAL :8 Scale Radio Controlled. Engine Powered WD Racing Car EVOLVA 003 INDEX REQUIRED
More informationp01.pdf
Before beginning assembly, please read these instructions thoroughly! V-ONE RR EVOLUTION CONVERSION KIT R THE FINEST RADIO CONTROL MODELS INSTRUCTION MANUAL No.39300 Symbols used throughout the instruction
More informationp01.pdf
Before beginning assembly, please read these instructions thoroughly. R THE FINEST RADIO CONTROL MODELS For Beginner & Intermediate Flyers INSTRUCTION MANUAL Wingspan: 1600mm (6.9") RADIO CONTROLLED.0
More informationKyosho Fantom Sports Manual
Before commencing assembly, please read these instructions thoroughly! R THE FINEST RADIO CONTROL MODELS FANTOM SPORTS INSTRUCTION MANUAL :8 Scale Radio Controlled. Engine Powered WD Racing Car Series
More informationKyosho Fantom 2001 Manual
INSTRUCTION MANUAL Before commencing assembly, please read these instructions thoroughly! R THE FINEST RADIO CONTROL MODELS FANTOM 00 :8 Scale Radio Controlled. Engine Powered WD Racing Car INDEX REQUIRED
More informationSPARE PARTS (2) FOR JAPANESE MARKET ONLY. No. Part Names No. Quantity No. Part Names No. Quantity
SPARE PARTS (2) FOR JAPANESE MARKET ONLY. No. Part Names No. Quantity No. Part Names No. Quantity 37 W5015 Shock End 247 x 4 W5105BL 129 x 4 Shock Cap Set (Blue) W5106 Shock Plastic Parts 118 x 2 W5107
More informationp01.pdf
Before commencing assembly, please read these instructions thoroughly! R THE FINEST RADIO CONTROL MODELS Radio Controlled. Engine Powered Racing Car Series INSTRUCTION MANUAL INDEX REQUIRED FOR OPERATION
More informationp01.pdf
Before beginning assembly, please read these instructions thoroughly. R THE FINEST RADIO CONTROL MODELS INSTRUCTION MANUAL : 0 SCALE RADIO CONTROLLED.5 ENGINE POWERED WD RACING BUGGY INDEX This kit is
More informationP001(FANTOM SPORTS).pdf
Before commencing assembly, please read these instructions thoroughly! R THE FINEST RADIO CONTROL MODELS FANTOM SPORTS INSTRUCTION MANUAL :8 Scale Radio Controlled. Engine Powered WD Racing Car Series
More informationP001(LANDMAX II)PEUGEOT.pdf
Before commencing assembly, please read these instructions thoroughly. THE FINEST RADIO CONTROL MODELS R INSTRUCTION MANUAL Super Eight GP LANDMAX WD PEUGEOT 06 WRC INDEX REQUIRED FOR OPERATION RADIO PREPARATION
More informationKyosho GP TR-15 Rally Manual
Before commencing assembly, please read these instructions thoroughly. R THE FINEST RADIO CONTROL MODELS INSTRUCTION MANUAL GP TR-5 RALLY WD MITSUBISHI LANCER EVOLUTION VII WRC INDEX This kit is half assembled.
More informationKyosho Super Ten GP FW-04 Manual
INSTRUCTION MANUAL Before commencing assembly, please read these instructions thoroughly! R THE FINEST RADIO CONTROL MODELS Size GP WD Radio Controlled.5 Engine Powered Touring Car Series SuperTen GP FW-0
More information内蔵ハードディスクユニット-20GB (PG-HD2E4H) 内蔵ハードディスクユニット-40GB (PG-HD4E4H)取扱説明書 HARD DISK DRIVE 20GB(PG-HD2E4H) HARD DISK DRIVE 40GB(PG-HD4E4H) USER'S GUIDE
B7FY-0351-02 J E J 1 J 1 2 3 2 4 J 3 4 Preface Thank you very much for purchasing the hard disk drive. This hard disk drive provides a IDE interface and can be installed in the 3.5-inch storage bay of
More information19403131 AFTER MARKET SERVICE CARD When purchasing Tamiya replacement parts, please take or send this form to your local Tamiya dealer so that the parts required can be correctly identified and supplied.
More informationP001.pdf
*Before beginning assembly, *please read these instructions thoroughly. R THE FINEST RADIO CONTROL MODELS INSTRUCTION MANUAL INDEX MAD FORCE RADIO CONTROLLED. ENGINE POWERED MONSTER TRUCK REQUIRED FOR
More informationP001.pdf
Before commencing assembly, please read these instructions thoroughly! R THE FINEST RADIO CONTROL MODELS Size GP WD D AMG Mercedes CLK INDEX REQUIRED FOR OPERATION RADIO PREPARATION BEFORE YOU BEGIN ARRANGEMENT
More informationTF6 面付p
Before beginning assembly, please read these instructions thoroughly! R THE FINEST RADIO CONTROL MODELS INSTRUCTION MANUAL :0 Scale Radio Controlled Electric Powered WD Touring Car TF6 INDEX REQUIRED FOR
More informationp01.pdf
*Before beginning assembly, please read these instructions thoroughly. THE FINEST RADIO CONTROL MODELS R INSTRUCTION MANUAL RADIO CONTROLLED. ENGINE POWERED MONSTER TRUCK INDEX REQUIRED FOR OPERATION RADIO
More informationp01.pdf
Before beginning assembly, please read these instructions thoroughly! THE FINEST RADIO CONTROL MODELS R INSTRUCTION MANUAL :0 SCALE RADIO CONTROLLED.-.5 ENGINE POWERED TOURING CAR SERIES CHASSIS KIT INDEX
More informationp01.pdf
Before beginning assembly, please read these instructions thoroughly! R THE FINEST RADIO CONTROL MODELS INSTRUCTION MANUAL PureTen GP WD CHASSIS KIT :0 SCALE RADIO CONTROLLED.-.5 ENGINE POWERED TOURING
More informationP001.pdf
Before commencing assembly, please read these instructions thoroughly. THE FINEST RADIO CONTROL MODELS R WINGSPAN: 930mm (36.6") For Intermediate & Advanced Flyers INSTRUCTION MANUAL RADIO CONTROLLED ELECTRIC
More informationp01.pdf
*Before beginning assembly, *please read these instructions thoroughly. R THE FINEST RADIO CONTROL MODELS INSTRUCTION MANUAL GIGA CRUSHER DF (Dual Force) / SCALE RADIO CONTROLLED.6 X ENGINE POWERED MONSTER
More informationOPERATING INSTRUCTION RNTD Model NTD Model To the use r In order to use the torque driver properly and safely,please read the instructions before oper
OPERATING INSTRUCTION RNTD Model NTD Model To the use r In order to use the torque driver properly and safely,please read the instructions before operation.if there are any questions,please contact a Tohnichi
More information1 2 3
INFORMATION FOR THE USER DRILL SELECTION CHART CARBIDE DRILLS NEXUS DRILLS DIAMOND DRILLS VP-GOLD DRILLS TDXL DRILLS EX-GOLD DRILLS V-GOLD DRILLS STEEL FRAME DRILLS HARD DRILLS V-SELECT DRILLS SPECIAL
More informationWARNING To reduce the risk of fire or electric shock,do not expose this apparatus to rain or moisture. To avoid electrical shock, do not open the cabi
ES-600P Operating Instructions WARNING To reduce the risk of fire or electric shock,do not expose this apparatus to rain or moisture. To avoid electrical shock, do not open the cabinet. Refer servicing
More informationp01.pdf
Before beginning assembly, please read these instructions thoroughly. INSTRUCTION MANUAL R THE FINEST RADIO CONTROL MODELS INFERNO MP INDEX REQUIRED FOR OPERATION RADIO PREPARATION BEFORE YOU BEGIN ARRANGEMENT
More informationfx-9860G Manager PLUS_J
fx-9860g J fx-9860g Manager PLUS http://edu.casio.jp k 1 k III 2 3 1. 2. 4 3. 4. 5 1. 2. 3. 4. 5. 1. 6 7 k 8 k 9 k 10 k 11 k k k 12 k k k 1 2 3 4 5 6 1 2 3 4 5 6 13 k 1 2 3 1 2 3 1 2 3 1 2 3 14 k a j.+-(),m1
More informationLC304_manual.ai
Stick Type Electronic Calculator English INDEX Stick Type Electronic Calculator Instruction manual INDEX Disposal of Old Electrical & Electronic Equipment (Applicable in the European Union
More informationHow to read the marks and remarks used in this parts book. Section 1 : Explanation of Code Use In MRK Column OO : Interchangeable between the new part
Reservdelskatalog MIKASA MVC-88 vibratorplatta EPOX Maskin AB Postadress Besöksadress Telefon Fax e-post Hemsida Version Box 6060 Landsvägen 1 08-754 71 60 08-754 81 00 info@epox.se www.epox.se 1,0 192
More information03-01 Senyouki.pdf
Special Surface Treatment Rust-free under normal use conditions. No loss of precision due to rust. Minimum maintenance required. Stub Holder KH-E KH-EC1 Stub Holder KH-A 406 KH-E Quick Change Stub Holder
More informationp01.pdf
Before commencing assembly, please read these instructions thoroughly. R WINGSPAN: 116mm THE FINEST RADIO CONTROL MODELS For Intermediate & Advanced Flyers RADIO CONTROLLED ENGINE POWERED ALL-BALSA AIRCRAFT
More informationI N S T R U M E N T A T I O N & E L E C T R I C A L E Q U I P M E N T Pressure-resistant gasket type retreat method effective bulk compressibility Fro
Cable Gland This is the s to use for Cable Wiring in the hazardous location. It is much easier to install and maintenance and modification compared with Conduit Wiring with Sealing Fitting. The Standard
More informationThe hand operated type HB unit is a worm gear drive which may be used for any valve or device requiring a 90 movement. The HB worm gear actuator is es
The hand operated type HB unit is a worm gear drive which may be used for any valve or device requiring a 90 movement. The HB worm gear actuator is especially designed for operation of butterfly, plug
More informationÉXÅ[ÉpÅ[ÉRÉuÉâï\éÜ
class SCLE HELICOPTER SUPERCOR W-1W ODY KIT INSTRUCTION MNUL SUPERCOR Please read this manual in its entirety before attempting to assemble the helicopter. This manual explains the parts exclusive to SUPERCOR.
More informationP001.pdf
Before commencing assembly, please read these instructions thoroughly. R WINGSPAN : 600mm THE FINEST RADIO CONTROL MODELS For Intermediate & Advanced Flyers INSTRUCTION MANUAL RADIO CONTROLLED ELECTRIC
More informationp01.pdf
Before commencing assembly, please read these instructions thoroughly. R THE FINEST RADIO CONTROL MODELS INSTRUCTION MANUAL INFERNO MP-7. INDEX REQUIRED FOR OPERATION RADIO PREPARATION BEFORE YOU BEGIN
More informationP001(GP BLUE STREAK 800).pdf
Before commencing assembly, please read these instructions thoroughly! R GPVERSION THE FINEST RADIO CONTROL MODELS LENGTH : 90mm INSTRUCTION MANUAL RADIO CONTROLLED.6 ENGINE POWERED RACING BOAT GP BLUESTREAK
More informationUT(W1600).indd
UT UT Thread Trimmer for W1600 Series W1600 Parts Catalog INTRODUCTION This parts catalog covers the UT device which are manufactured in November, 2006. The components are shown on pages 4-19. The illustrations
More informationp01.pdf
Before commencing assembly, please read these instructions thoroughly! WINGSPAN: 156mm R THE FINEST RADIO CONTROL MODELS For Intermediate & Advanced Flyers. INSTRUCTION MANUAL RADIO CONTROLLED ENGINE POWERED
More informationES8259取説
ES8259 B B B B 2 µm µm C C C C µm µm 1 3 4 2 H H 3 C C C C C C C C C C C C C C C C C C C C C C C C C C C 4 B B B B B B B B B B B B 5 B B B C C B B C C B B B C B C B B B 6 7 8 OFF/ON $ & ( $ ' # % # $ %
More informationHow to read the marks and remarks used in this parts book. Section 1 : Explanation of Code Use In MRK Column OO : Interchangeable between the new part
Reservdelskatalog MIKASA MVB-85 rullvibrator EPOX Maskin AB Postadress Besöksadress Telefon Fax e-post Hemsida Version Box 6060 Landsvägen 1 08-754 71 60 08-754 81 00 info@epox.se www.epox.se 1,0 192 06
More informationp01.pdf
efore commencing assembly, please read these instructions thoroughly! R THE FINEST RADIO CONTROL MODELS INSTRUCTION MANUAL REQUIRED FOR OPERATION TOOLS REQUIRED EFORE YOU EGIN 3 RADIO PREPARATION 3 ASSEMLY
More information<45934B8D87955C B1D9CCA733816A2E786C73>
92001 On-Road Spring (Hard) 4955439738085 1284 Pillow Ball(5.8) 4955439654972 1710 Special Antenna Holder 4955439653845 1710V Special Antenna Holder II 4955439752456 1916 5x10 Bushing (=FD26) 4955439655450
More informationHow to read the marks and remarks used in this parts book. Section 1 : Explanation of Code Use In MRK Column OO : Interchangeable between the new part
Reservdelskatalog MIKASA MT65H vibratorstamp EPOX Maskin AB Postadress Besöksadress Telefon Fax e-post Hemsida Version Box 6060 Landsvägen 1 08-754 71 60 08-754 81 00 info@epox.se www.epox.se 1,0 192 06
More informationp01.pdf
Before commencing assembly, please read these instructions thoroughly! WINGSPAN: 1375mm R THE FINEST RADIO CONTROL MODELS For Intermediate & Advanced Flyers. INSTRUCTION MANUAL RADIO CONTROLLED ENGINE
More informationHow to read the marks and remarks used in this parts book. Section 1 : Explanation of Code Use In MRK Column OO : Interchangeable between the new part
Reservdelskatalog MIKASA MVC-50 vibratorplatta EPOX Maskin AB Postadress Besöksadress Telefon Fax e-post Hemsida Version Box 6060 Landsvägen 1 08-754 71 60 08-754 81 00 info@epox.se www.epox.se 1,0 192
More informationÉgÉEÉRÉuÉâï\éÜ
60 class SCLE HELICOPTER TOWCOR H-1SIII ODY KIT INSTRUCTION MNUL TOWCOR 60 Please read this manual in its entirety before attempting to assemble the helicopter. This manual explains the parts exclusive
More informationp01.pdf
Before beginning assembly, please read these instructions thoroughly. R THE FINEST RADIO CONTROL MODELS INSTRUCTION MANUAL II INFERNO MP-7. II YUICHI KANAI EDITION INDEX REQUIRED FOR OPERATION RADIO PREPARATION
More informationCS-3000_3400(6digits)(35)(36)_CS-3000_3400(6digits)(35)(36)_EN.xls
PARTS CATALOG TOP HANDLE SAW - 36057511 1. Cylinder, Crankcase, Piston 5 100202-39130 1 CRANKCASE SET Sus. by 100202-39131 5 100202-39131 1 CRANKCASE SET CS-3000 5 100202-39530 1 CRANKCASE SET Sus. by
More informationHG…p†[…c…J…^…“…O
HG Hemming guide device Machine models W(T)664 Series / HG Series Parts Catalog INTRODUCTION This parts catalog covers the HG Series device. On pages 2-37, each mechanism is arranged on facing pages, the
More informationTK-M700…p†[…c…−…X…g
TK Tape cutter device Machine models M700 Series / TK Series Parts Catalog INTRODUCTION This parts catalog covers the TK Series device. On pages 3-12, each mechanism is arranged on facing pages, the first
More informationHow to read the marks and remarks used in this parts book. Section 1 : Explanation of Code Use In MRK Column OO : Interchangeable between the new part
Reservdelskatalog MIKASA MCD-L14 asfalt- och betongsåg EPOX Maskin AB Postadress Besöksadress Telefon Fax e-post Hemsida Version Box 6060 Landsvägen 1 08-754 71 60 08-754 81 00 info@epox.se www.epox.se
More informationVol. A-TAP A-SFT A-POT Highly Efficient Multi-Purpose Tap Series Galling No Galling Galling No Galling Spiral Fluted Tap NEXT NEW SIZES FROM NEXT Spiral Fluted Tap FROM P.18 P.20 NEXT NEW SIZES FROM
More information面付け
組立てる前にこの説明書を良くお読みになり十分に理解してください Before Begining assembly, please read these instructions thoroughly. R For Intermediate & Advanced Flyers WINGSPAN: 100mm (55.1") - SP 1300mm (51.") - ST 中 上級者向 組立 取扱説明書
More information00_20
KAWADA CATALOG 2004 Vol.11 www.kawadamodel.co.jp 1/10th scale TOURING CAR SV-10 SIGMA 1-2 kit, spare parts, option parts 1/10th scale TOURING CAR SV-10 ALCYON series 3 kit, spare parts, option parts 1/12th
More information1) 1) Props of preparation. Wire Scale Spike Cutter Hammer Tape Marker (, ) Rope(For Sezing) 2) 2) Marking A 22 A point Position of twenty-two times t
1) 1) Props of preparation. Wire Scale Spike Cutter Hammer Tape Marker (, ) Rope(For Sezing) 2) 2) Marking A 22 A point Position of twenty-two times the Dia, from the end of the rope. B A B point Position
More informationINSTRUCTION MANUAL WARNING Be sure to READ the Instruction Manual. Prior to using, be sure to check whether the machine functions properly. If not, NE
INSTRUCTION MANUAL WARNING Be sure to READ the Instruction Manual. Prior to using, be sure to check whether the machine functions properly. If not, NEVER use it. NEVER apply your fingers to near the front
More informationAnl_MonzaJAP.indd
ENGLISH A car racing game which encourages tactical thinking for 2 to 6 clever players ages 5 to 99. Author: Jürgen P. K. Grunau Illustrations: Haralds Klavinius Length of the game: 10-15 minutes approx.
More informationMFS 8A3 9.8A3 #026832XE OB NO.002-21051-4 0910 NB 3,400 HOW TO USE THIS PARTS LIST 1. This Parts List contains the component parts of the Tohatsu outboard motors. 2. Please keep the Parts List updated
More informationP3FY J E
P3FY-1490-01 J E J 1 J 1 2 2 J 3 3 4 4 5 J 5 Preface Thank you very much for purchasing the hard disk drive. This hard disk drive provides a IDE interface and can be installed in the 3.5-inch storage
More informationWE WESB WENB WESNB 428
KH-A-NL Quick Change Stub Tapper Designed for use on KH-A spindle. Spindle Feed: All kinds of feed styles.for spindle feed other than pitch feed, use KH-A-NL in a condition where the tension feature always
More informationOPERATING INSTRUCTION RNTD Model NTD Model To the use r In order to use the torque driver properly and safely,please read the instructions before oper
OPERATING INSTRUCTION RNTD Model NTD Model To the use r In order to use the torque driver properly and safely,please read the instructions before operation.if there are any questions,please contact a Tohnichi
More informationW200テンプレート.indd
W200 Small Cylinder Bed Interlock Stitch Machines Parts Catalog INTRODUCTION This parts catalog covers the W200 series machine manufactured in January, 2003. The components of W200 series are arranged
More informationp01.pdf
Before beginning assembly, please read these instructions thoroughly! THE FINEST RADIO CONTROL MODELS R INSTRUCTION MANUAL :0 SCALE RADIO CONTROLLED.-.5 ENGINE POWERED TOURING CAR SERIES CHASSIS KIT INDEX
More informationMFS 2B 2.5B 3.5B OB NO NB 3,000
MFS B.5B 3.5B OB NO.00-105-1 0910 NB 3,000 HOW TO USE THIS PARTS LIST 1. This Parts List contains the component parts of the Tohatsu outboard motors.. Please keep the Parts List updated each time when
More informationp01.pdf
Before commencing assembly, please read these instructions thoroughly. R WINGSPAN: 1800mm THE FINEST RADIO CONTROL MODELS For Intermediate & Advanced flyers. INSTRUCTION MANUAL RADIO CONTROLLED ENGINE
More informationNo_ST012.indd
Pipe Threading Machine Supertronic INSTRUCTION MANUAL Double Insulation Important: For your safety and effective operation, read this Instruction Manual carefully and completely before use and thoroughly
More information03-03 Bush Mentori.pdf
54 541 A Headless Press Fit Bush Type A 1. Bushing with I.D. size smaller than 3.mm uses 3 degreed chamfered radius (R). SAG6 +.2 +.4 +.14 +.5 +.17 +.1 A +.2 +.2 +.3 +.4 +.36 +.5 +.43 +.52 +.62 +.74 +.1
More informationelemmay09.pub
Elementary Activity Bank Activity Bank Activity Bank Activity Bank Activity Bank Activity Bank Activity Bank Activity Bank Activity Bank Activity Bank Activity Bank Activity Bank Number Challenge Time:
More information01.eps
444 SumiTurn T-REX Tool Holders Cost reduction for copying with unique multiple cornered insert Carbide inserts, cermet inserts and 4 types of breakers are available. Expansion of our popular steel turning
More informationTL140 Book No BT9Z009 S N 21
TL140 Book No. BT9Z009 S/N 21400011- Index TL140 Book No.BT9Z009 Serial No.21400011-3 5 10 6 1 2 4 8 Reference Index ヘ ーシ 0-1 TL140 Book No. BT9Z009 S/N 21400011- How to read the parts manual(1/9) Reference
More information2
8 23 26A800032A8000 31 37 42 51 2 3 23 37 10 11 51 4 26 7 28 7 8 7 9 8 5 6 7 9 8 17 7 7 7 37 10 13 12 23 21 21 8 53 8 8 8 8 1 2 3 17 11 51 51 18 23 29 69 30 39 22 22 22 22 21 56 8 9 12 53 12 56 43 35 27
More information2
8 22 19A800022A8000 30 37 42 49 2 3 22 37 10 11 49 4 24 27 7 49 7 8 7 9 8 5 6 7 9 8 16 7 7 7 37 10 11 20 22 20 20 8 51 8 8 9 17 1 2 3 16 11 49 49 17 22 28 48 29 33 21 21 21 21 20 8 10 9 28 9 53 37 36 25
More information2
8 24 32C800037C800042C8000 32 40 45 54 2 3 24 40 10 11 54 4 7 54 30 26 7 9 8 5 6 7 9 8 18 7 7 7 40 10 13 12 24 22 22 8 55 8 8 8 8 1 2 3 18 11 54 54 19 24 30 69 31 40 57 23 23 22 23 22 57 8 9 30 12 12 56
More informationThread Mill Series
Thread Mill Series Index Go to the following for the quick tool search. Guide to Icons Tool Materials Helix Angle Shank Tungsten Carbide Cobalt HSS Helix angle of flute for cutters Tolerance for shank
More informationKyosho Inferno MP-7.5 Kanai 3 Edition Manual
ご使用前にこの説明書を良くお読みになり十分に理解してください Before beginning assembly, please read these instructions thoroughly. R THE FINEST RADIO CONTROL MODELS 写真のボディ ウイング用デカールはキットに付属しません 通常のキットデカールが付属します Pi ct ur eshowsspeci
More informationE適合表(TR15).xls
1245-073 Swing Shaft (5.8) 4955439647035 1284 Pillow Ball(5.8) 4955439654972 1296 6.8 Ball End (12 pcs) 4955439653838 1710 Special Antenna Holder 4955439653845 1710V Special Antenna Holder II 4955439752456
More informationES-2400_ES-2400_EN.xls
PARTS CATALOG SHRED 'N' VAC 1. Cylinder, Crankcase, Piston 1 101011-08960 1 CYLINDER (CR) 17 101003-08960 1 CYLINDER PISTON KIT 1 + 101011-08961 1 CYLINDER (CR) 5 + 100011-09560 2 RING, PISTON 7 + 100015-04630
More informationM6B_8B_98B_body.indd
M 6B 8B 9.8B 1. 2. 3. 4. ' 5. 1) """" 6. No. No. 7. "" "" HOW TO USE THIS PARTS LIST 1. This Parts List lists the component parts of the Tohatsu outboard motors. 2. Please keep the Parts List updated
More information5 11 3 1....1 2. 5...4 (1)...5...6...7...17...22 (2)...70...71...72...77...82 (3)...85...86...87...92...97 (4)...101...102...103...112...117 (5)...121...122...123...125...128 1. 10 Web Web WG 5 4 5 ²
More information5 7 3AS40AS 33 38 45 54 3 4 5 4 9 9 34 5 5 38 6 8 5 8 39 8 78 0 9 0 4 3 6 4 8 3 4 5 9 5 6 44 5 38 55 4 4 4 4 5 33 3 3 43 6 6 5 6 7 3 6 0 8 3 34 37 /78903 4 0 0 4 04 6 06 8 08 /7 AM 9:3 5 05 7 07 AM 9
More informationP001(MP-7.5 Y.K III)
ご使用前にこの説明書を良くお読みになり十分に理解してください Before beginning assembly, please read these instructions thoroughly. R THE FINEST RADIO CONTROL MODELS 写真のボディ ウイング用デカールはキットに付属しません 通常のキットデカールが付属します Pi ct ur eshowsspeci
More information2
8 23 32A950S 30 38 43 52 2 3 23 40 10 33 33 11 52 4 52 7 28 26 7 8 8 18 5 6 7 9 8 17 7 7 7 38 10 12 9 23 22 22 8 53 8 8 8 8 1 2 3 17 11 52 52 19 23 29 71 29 41 55 22 22 22 22 22 55 8 18 31 9 9 54 71 44
More information6 4 45 7ZS 5 59 7 8 94 05 4 5 6 4 5 5 6 8 8 40 45 48 56 60 64 66 66 68 7 78 80 8 7 8 0 0 0 90 0 57 64 69 66 66 69 0 4 4 4 4 4 0 7 48 5 4 4 5 4 4 4 7 46 46 6 46 8 46 48 46 46 4 46 46 4 4 5 4 6 4 9 9 0
More informationCanofix_Manual_JP 1805
Installation Manual Thank you for purchasing CANOFIX. Please give us a call or email if you have any questions regards toinstallation. (* canofixjapan@gmail.com *Required Tools Copyright 2015 Mr. Can All
More informationMIDI_IO.book
MIDI I/O t Copyright This guide is copyrighted 2002 by Digidesign, a division of Avid Technology, Inc. (hereafter Digidesign ), with all rights reserved. Under copyright laws, this guide may not be duplicated
More information6 4 4 9RERE6RE 5 5 6 7 8 9 4 5 6 4 4 5 6 8 4 46 5 7 54 58 60 6 69 7 8 0 9 9 79 0 4 0 0 4 4 60 6 9 4 6 46 5 4 4 5 4 4 7 44 44 6 44 8 44 46 44 44 4 44 0 4 4 5 4 8 6 0 4 0 4 4 5 45 4 5 50 4 58 60 57 54
More informationOn the Wireless Beam of Short Electric Waves. (VII) (A New Electric Wave Projector.) By S. UDA, Member (Tohoku Imperial University.) Abstract. A new e
On the Wireless Beam of Short Electric Waves. (VII) (A New Electric Wave Projector.) By S. UDA, Member (Tohoku Imperial University.) Abstract. A new electric wave projector is proposed in this paper. The
More information平成29年度英語力調査結果(中学3年生)の概要
1 2 3 1 そう思う 2 どちらかといえば そう思う 3 どちらかといえば そう思わない 4 そう思わない 4 5 楽しめるようになりたい 6 1 そう思う 2 どちらかといえば そう思う 3 どちらかといえば そう思わない 4 そう思わない 7 1 そう思う 2 どちらかといえば そう思う 3 どちらかといえば そう思わない 4 そう思わない 8 1 そう思う 2 どちらかといえば そう思う
More information